J. A. Roby ROBY2500 CUISINIERE User manual

November 5, 2015 Printed in Canada
Tested and listed
ULC STD S627-00
UL 1482-7
CAN/CSA STD B415.1
-
10
Instruction Manual
490, rue de l'Argon
Quebec, CANADA G2N 2C9
Tel.: [phone] Fax : [phone]
www.jaroby.com
PLEASE READ CAREFULLY AND KEEP
THIS MANUAL FOR FUTURE REFERENCE
ROBY2500 CUISINIERE LX
ROBY2500
ROBY2500 CUISINIERE

November 5, 2015
TABLE OF CONTENTS
Introduction...............................................................................3
Rating plate ..............................................................................4
Appliance Dimensions..............................................................5
Installation ................................................................................6
Floor protection ....................................................................6
Minimum dimension of floor protection plate ...................6
Clearances chart on floor plate........................................7
Minimums clearances to combustible material.....................8
Assembly before installation ................................................9
Installing legs...................................................................9
Warmer stove Assembly (Optional) .................................9
Fan and Snap disc box installation ................................11
Firebricks installation..........................................................12
General stove installation steps .........................................15
Chimney connector installation ..........................................16
Mobile home installation.....................................................18
...........................................................................................18
General steps of chimney installation ................................19
Vertical Installation Inside Masonry Chimney ................20
Outside Vertical Installation ...........................................20
Vertical Installation on Cathedral Roof...........................21
Offset Vertical Installation ..............................................21
Vertical Installation.........................................................22
Combustion air intake.............................................................22
Air Inlet Obstruction .......................................................22
Replacing stainless steel deflector.....................................23
Replacement stainless steel tubes.....................................24
Stainless steel tubes Installation.................................... 24
Operating Instructions ............................................................25
Control of primary and secondary air admission................25
Lightning fire ...................................................................... 25
First fire..............................................................................25
Keeping a fire.....................................................................25
Fan Control ........................................................................ 25
Maintenance........................................................................... 26
Ash Removal .................................................................26
Ash Disposal..................................................................26
Creosote Formation.......................................................26
Chimney Inspection .......................................................26
Chimney Sweeping........................................................27
Door maintenance .........................................................27
Air Tighten Adjustment ..................................................27
Cleaning up glass .......................................................... 27
Disassembly and reassembly of door............................ 27
Replacing broken glass .................................................27
Replacing glass fiber rope ............................................. 28
What to do in case of Chimney Fire .......................................28
Annexe 1 ................................................................................ 29
Door assembly................................................................... 29
Wood Stove Door ..........................................................29
Annexe 2 ................................................................................ 30
Replacement parts.............................................................30
J. A. Roby Limited Lifetime warranty......................................31

3
November 5, 2015
Introduction
Read all instructions carefully before installing your new J. A. ROBY ROBY2500/ROBY2500 CUISINIERE wood stove. A proper
installation is very important for a safe and effective use of your stove. If you have any doubts about the installation of your appliance
correctly, we suggest to call a professional installer. A wrong installation may result in a fire, injury or loss of life.
Keep these instructions for future use.
This appliance must be connected to
•A type HT chimney of 6 inch diameter (15.24 cm) listed to UL-103 or ULC-S629
•A conforming masonry chimney of 6 inch diameter (15.24cm) with qualified internal lining
N.B: Please be aware that the local codes and regulations might be more specific than this manual. You can consult a
professional installer, the Fire Department or local authorities about restriction on installation of solid-fuel burning
appliances.
DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

4
November 5, 2015
Rating plate

5
November 5, 2015
Appliance Dimensions
Figure 1

6
November 5, 2015
Installation
Floor protection
Your stove must be installed on a plate of non-combustible material to protect the floor and avoid fire caused by:
•Projections of sparks at the moment of opening the door and loading.
•The heat radiation of runaway which might cause self-ignition of floor and surface.
•Possible creosote flow when there is a chimney fire.
UNITED STATES ONLY: The surface must be non-combustible and listed to the USA standard UL1618 or the local codes (Example:
cement, brick, ceramic tiles etc.)
Minimum dimension of floor protection plate
The following dimensions are the minimum values.
Canada:
•41 7/8 inches (106 cm)
•47 5/8 inches (115.88 cm)
•3/8 inch thickness (1 cm)
Unites States:
•41 7/8 inches (106.42 cm)
•45 5/8 inches (115.88 cm)
•3/8 inch thickness (1 cm)
UNITED STATES ONLY: It’s necessary to protect the floor
beneath the horizontal part of chimney connector extending
2 inch (5cm) beyond each side of the pipe. You can extend
the floor protection panel while respecting the clearances of
each side of stove.

7
November 5, 2015
Clearances chart on floor plate
The following dimensions are the minimum values.
Canada:
•8 inches (20.32 cm) rear
•8 inches (20.32 cm) side
•18 inches (45.72 cm) loading door
Unites States:
•8 inches (20.32 cm) rear
•8 inches (20.32 cm) side
•16 inches (40.64 cm) loading door

8
November 5, 2015
Minimums clearances to combustible material
This appliance needs a minimum space because of these reduced clearances. Whether in the living room or the dining room, the
ROBY2500/ ROBY2500 CUISINIERE will match perfectly by its originality and heating. It requires a MINIMUM clearance of 12 inches
at the back (for a single pipe with a heat shield) and an 18 inch MINIMUM clearance on each side.
1) In case of a single pipe without heat shield, you must keep ROBY2500/ ROBY2500 CUISINIERE cook stove 18 inches
away from all combustible material so that the MINIMUM clearance at the back of the stove will be 16¼ inches
(41.3cm).
•For a 45° corner installation, or other corner installation, the
minimum clearance between the cook stove and
combustible material must be 18 inches.
Figure 3

9
November 5, 2015
Assembly before installation
The stove leg and the warming oven top might not be assembled
in the factory, in order to save space for transportation and
storage. You must therefore assemble these parts before
installing the cook stove.
Installing legs
1) Take out legs and bricks from combustion chamber.
2) Unscrew the stove from the skids.
3) Lay the stove on its back carefully not to damage the
paint.
4) Loosen the nut (#2) without removing it completely.
5) Install the legs (#1) as illustrated below.
Attention: Make sure the legs are in place, correctly
positioned and in contact with the bottom of the
stove.
Warmer stove Assembly (Optional)
At this moment, you need to know which type of smoke pipe you
are installing: a single pipe or a double pipe.
For the single pipe, it is not necessary to remove the pre-cut
metal part.
For the double pipe, you must remove the pre-cut metal part on
the top, inside and in front of the warmer, see pictures below.
Couper le contour
Cut the edg
e
Couper le contour
Cut the
edge
Couper le contour
Cut the edge

10
November 5, 2015
1) Place the backside on the product package to protect
the painted part.
2) Fix the left side.
3) Fix the right side.
4) Attach the front part (with the door) to the two sides
and the back. Leave the horizontal holes empty for
the chrome decoration.
5) Insert the chrome decoration in the holes and fix it
with carriage bolts and nuts (with 2 bolts each).
6) Attach the top part to the back and the front.
7) Install the left chrome decoration.
8) Install the right chrome decoration.