J D Williams New England QN913 User manual

Dimensions
Width - 32cm
Depth - 31cm
Height - 60cm
Important– Please read these instructions fully before starting assembly
Assembly Instructions- please keep for future reference
464/3944
New England Laundry Hamper
Issue 1 - 16/05/2016
QN913

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers

H
4PCS
2
Components -Panels
Please check you have all the panels listed below
Components - Fittings
Note:
may be supplied than are required.
Tools required
Phillips screwdriver
(medium & large)

3

4
Assembly Instructions
F
E
E
F
Step 1
1. Into left side panel 2
insert 6 x Male Camlocks
and 4 x Dowels C as
shown.
2. Into Right side panel 1
insert 6 x Male Camlocks
and 4 x Dowels C as
shown.
Step 2
Step 3
1
1. Slide Base panel 5
into position as shown
C
A
C
A
C
A
C
A
C
A
C
A
C
A
C
A
C
A
C
A
C
A
C
A
2
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
1
3
C
B
C
B
C
B
C
B
C
B
C
B4
5
C
A
C
A
1
2
C
C
C
C
1. Connect Right Side
panel 1 to Back panel
3 and Front panel 4
as shown, locating
dowels and Male
camlocks into adjacent
holes.
2. Insert 6 x Female
camlocks and
tighten with a Phillips
screwdriver
1
34
C
B
5

5
Assembly Instructions
Step 4
Step 5
Step 6
C
B
C
B
C
B
C
B
C
B
C
B
2
6
C
E
C
D
C
D
C
E
C
E
C
E
C
E
C
E
C
F
C
G
1. ConnectLeft Side
panel 1 to Back panel
3 and Front panel 4
as shown, locating
dowels and Male
camlocks into adjacent
holes.
2. Insert 6 x Female
camlocks and
tighten with a Phillips
screwdriver
2
34
C
B
1. Connect Lid 6 to the
unit using 2 x Hinges D
and 8 x Screw E
2. Add 4 x Protective feet
H to the legs of the unit
6
C
D
C
E
1. Add 2 x Safety hinges
to the unit using 8 x
Screw E. Hinge G
attaches to Left side
panel 2 and hinge F
attaches to Right side
panel 1.
2
1
C
G
C
E
C
F
2
1
C
H
C
H
C
H
C
H