Jacobsen HR-9016 Turbo User manual

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
Jacobsen HR9016 ROPS Cab
** Shown with optional equipment
Jacobsen HR9016 ROPS Cab
This ROPS cab is designed and built
to fit the Jacobsen HR9016.
Designed and Built by:
Tektite Manufacturing Inc:
24157 Hwy 3
P.O. Box 639
Winkler, MB
R6W 4A8
Canada
PH: 204-331-3463
Fax: [phone]
[e-mail]
One year standard product
warranty provided by Tektite.
Caution
** Please read installation instructions and follow all safety statements before attempting operating
this ROPS product.
** A copy of this operator manual should be kept with the machine operating manuals.
** If this manual is lost, please contact your local Jacobsen dealer for a replacement.

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
Tektite Manufacturing Incorporated thanks you for purchasing a Jacobsen HR9016 ROPS cab!
Tektite has worked very hard to design and build this ROPS product and we hope that it
provides you with many years of ROPS protection.
Tektite’s ROPS products are designed to provide safe and dependable service during operation
when they are properly maintained according to the instructions. Please read this operator
manual carefully before using this ROPS product.
The photos/illustrations provided in this manual may not provide all the detail needed, and are
for reference only.
All directions provided are from the reference point of the tractor seat facing the steering
wheel. All left and right references are from this view point.
For reference, please fill in the information below. This will assist your dealer in providing
service for this ROPS. It is advisable that this information be provided to your insurance
company as well in the event that the tractor is lost or damaged.
Vehicle Model: _________________________________________________________
ROPS Serial Number: ___________________________________________________
Date of Purchase: _______________________________________________________
Dealer Name: ___________________________________________________________

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
Safety Precautions
Safety First
Read these instructions carefully. It is essential that you read the instructions and safety
regulations before you attempt to assemble or use the features that are on this cab/ROPS.
Danger: Indicates an immediate hazardous situation which, if not avoided, will result in death
or serious injury.
Warning: Indicates a potentially hazardous situation which, if not avoided, may result in death
or serious injury.
Caution: Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
Caution: Raising wing decks with side doors and side windows open can cause door glass to
break!
Important: Indicates that cab or property damage may result if instructions are not carefully
followed.
NOTE: All products are designed to give safe, dependable service if they are operated and
maintained according to instructions. It is the owner’s responsibility to be certain anyone
operating this product reads this manual, and all other applicable manuals, to become familiar
with this cab and all safety precautions. Failure to do so could result in serious personal injury
or cab damage. If you have any questions, consult your dealer. Read and understand this
manual before operation.
NOTE: A safe operator is the best assurance against accidents. All operators, no matter how
experienced they may be, should read this operator manual and all other related manuals
before attempting to operate features in this cab/ROPS and operate the base tractor. Please
read the following section and pay particular attention to all safety recommendations
contained in this manual and those labelled on the cab and on the tractor.

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
General Safety
1. Never let an unqualified or untrained driver operate the mower.
2. Keep a fire extinguisher, with ABC rating securely fastened in the ROPS. Maintain it and be
familiar with its use.
3. Do not carry passengers.
4. Never operate the mower in a closed building for a prolonged period. Ensure adequate
ventilation is present, as engine exhaust fumes are poisonous and can kill.
5. Always keep sleeves, jackets or other loose clothing relatively tight and belted. Loose clothing
may catch on moving parts and result in severe personal injury or death.
6. Provide a first-aid kit, securely attached inside of the ROPS for use in case of accident.
7. Never jump from the mower. There is a danger of tripping or falling on protruding parts.
8. Use steps and hand holds when mounting and dismounting the mower, or for servicing
components too high to reach from the ground.
9. When seated in the ROPS, fasten seat belt before starting the engine. A proper seat belt must
be worn at all times when using a ROPS.
10. Safety devices and shields are intended to protect operators from injury or death. Under no
circumstances should they be modified, disabled or removed.
Operating Safety
1. Always operate the mower controls while sitting in the operator’s seat.
2. Lock seat in position and buckle seat belt before operating the mower.
3. Avoid abrupt sharp turns at high speeds.
4. On sloped terrain, do not make sharp turns as machine stability could be compromised.
5. Operate the mower smoothly, avoid abrupt starts and stops.
6. Keep all shields in place when operating the mower.
7. Do not operate the mower when you are tired, sick, or impaired.
8. Never operate the mower in confined areas; visibility next to the tractor is reduced. Injury to
bystanders or damage to the ROPS or equipment may result.
Safety
Carefully review the procedures given in this manual and the mower operator’s manual with all
operators annually. It is important that all operators become familiar with, and follow safety
precautions. Operating instructions must be given to everyone using the tractor before
operation and at least once yearly thereafter in compliance with OSHA Regulations 1928.57
(United States).

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
Safe Operation on Rough Terrain
1. Drive the mower slowly on hillsides and curves to eliminate the danger of tipping. Avoid
slopes which are too steep for safe operation. Avoid sharp uphill turns.
2. Always drive slowly enough over rough ground or obstructions. Drive at speeds slows enough
to ensure your safety.
3. When driving out of a ditch, gully, or up a steep hillside, engage the clutch slowly. Avoid
sharp uphill turns.
4. When descending steep grades, select a sufficiently low gear to maintain control with
minimum use of braking.
5. Use caution when driving near the edge of a ditch or gully. It may cave in, causing the mower
to roll over.
6. Be alert when operating near trees, slopes and around obstructions. Tree branches can cause
damage to ROPS components.
Maintenance Safety
1. Remove mud, crop residue, chains, and tools from steps and operator’s platform. They may
interfere with pedal operation or entry/exit from mower.
2. When servicing components are too high to reach from the ground use steps and handholds.
Do not use fenders or shields that are not designed as steps.
Safe Highway Operation
1. Before operating the mower on, or near, public roadways check with your local authorities
for any local regulations that will affect you.
2. Equip towed implements with slow moving vehicle (SMV) signs when traveling on public
roads.
3. Install additional lights on implement rear to safeguard against rear end collisions.
4. Use hazard warning flashers as required by law when transporting or driving on public roads.
If the mower had warning flashers removed when mounting the ROPS, they must be replaced
prior to operation on public roads.
5. Keep to the right, yielding right-of-way traffic, especially if pulling implements. Pull off the
road and stop to allow motorists to pass. Drive on the road shoulder, if permitted by law.
6. Use extreme caution when pulling heavy loads at road speeds. Avoid hard application of the
mower brakes at high speed.
7. Always drive slowly near curbs, approaches or ditches.
8. If equipped, ensure headlights are aligned so they will not blind the operator’s of oncoming
vehicles. If the mower is not equipped with turn signals and law requires them, install them
prior to operating on or near public roads.

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
9. Use your turn signals, checking for traffic well in advance of turning. If the mower is not
equipped with turn signals and law requires them, install them prior to operating on or near
public roads.
Safety Decals
1. Keep decals clean. Remove dirt with a wet clean cloth when necessary.
2. Replace safety decals if destroyed, missing, painted over or unreadable. If any safety decals
are covered or obscured when the ROPS is mounted, it is recommended that you purchase
replacement decals from the mower manufacturer. Mount them in a readable location at, or
near, their original location before operating the mower.
3. New ROPS decals and mower decals are available from your mower dealer.
ROPS Safety
1. Install the ROPS in accordance with Tektite mounting instructions. Failure to do so may affect
the ROPS ability to withstand a roll over.
2. If the ROPS is subjected to alteration, structural damage or involved in an over turn accident,
the entire structure must be replaced. Failure to do so may result in injury or death in the event
of a roll over.
3. If the mower in not equipped with seat belts, purchase approved seat belts from the mower
manufacturer or Tektite prior to operating the mower.
4. Always fasten seat belts prior to operating the mower.
5. Always operate the mower from the operator’s seat.
6. Remove mud, crop residue, chains and tools from steps and operator’s platform. They may
interfere with pedal operation or entry/exit from the mower.
7. Remove all loose chains, tools, and equipment from the operator’s platform. Failure to do so
may cause injury or death in the event of a roll over.
8. Do not install the ROPS on a mower model that the ROPS is not designated for (compatible
mower designations are printed on the ROPS serial number plate). The ROPS is designed
specifically for individual models to ensure ROPS requirements will be met. Installing the ROPS
on a non designated mower may result in injury or death.
Emergency Exits
This ROPS cab has 2 exits, which may be used in an emergency: left and right side doors.

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
Operating Instructions
Important
The following section locates, identifies and briefly describes the functions of all cab controls.
All operators should familiarize themselves with control location and function prior to operating
the mower. Failure to do so may result in unsafe operation of the mower and possible injury or
death to operators and bystanders.
There are two switch plates located in the headliner.The following switches are available and
their functionality is described.
Left Switch Plate
1. Front Wiper Rocker Switch (standard)
Low position: Off
High position: On
Note: indicator light activates when wiper is on.
2. Rear Wiper Rocker Switch (optional)
Low position: Off
High position: On

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
Note: indicator light activates when wiper is on.
3. Front Work Light Rocker Switch (optional)
Low position: Off
High position: On
Note: indicator light activates when work lights are on.
4. Rear Work Light Rocker Switch (optional)
Low position: Off
High position: On
Note: indicator light activates when work light is on.
5. Head Lights Rocker Switch (optional)
Low position: Off
High position: On
Note: indicator light activates when head lights are on.
6. Front and Rear Washer Rocker Switch (optional)
Low position: Momentary – On Rear Washer
Middle position: Off
High position: Momentary – On Front Washer
7. Turn Signal Rocker Switch (optional)
Left position: On
Middle position: Off
Right position: On
Right Switch Plate
1. Beacon Rocker Switch (standard)
Low position: Off
High position: On
Note: indicator light activates when beacon is on.
2. Hazard Rocker Switch (optional)
Low position: Off
High position: On
Note: indicator light activates when 4-way flashers are on.
3. Air Conditioner Rocker Switch (optional)
Low position: Off
High position: On
Note: indicator light activates when air conditioner is on.

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
4. Fan Rotary Switch (optional)
Indicator mark above switch indicates whether fan is operational or not.
5. Temperature Control Rotary Switch (optional)
Indicator mark at lower left corner indicates current temperature setting. Rotate to increase
heat output or to decrease heat output of heating system. When air conditioner is being used,
it is recommended that the switch be at maximum cooling position.
Optional turn signal switch lever mounted to steering console is also available. Lift up to
indicate right turn. Push down to indicate left turn. 4-way hazards can also be activated with
this switch lever.
Cab Circuit Protection
The Tektite ROPS cab is wired to provide maximum protection against accidental battery
rundown and circuit overload. A relay in the cab is ignition activated and prevents the operator
from accidentally leaving fan motors, lights on after turning the tractor off and leaving for the
day. A circuit breaker is provided to prevent the cab electrical components from drawing more
power than they should be able to from a dead short. The cab electrical components are also
fused individually, and the fuse block is located in the headliner, directly above the door
opening on the left side. Locate the 3” snap cap, and with a small flat screw driver you can
remove the cap to examine the fuses provided. A decal on the fuse block indicates which fuse
is for which electrical option.

August 2015©
Jacobsen HR9016 ROPS Cab Operator Manual
After your ROPS Cab has been installed:
Before starting a mower equipped with a Tektite ROPS cab:
1. Clear the operator platform of all tools. Tools left in or around the ROPS and mower can
cause operator interference which could lead to bodily injury and/or damage the machine.
2. Inspect the ROPS and mower to ensure all bolts are tight and re-tighten if required.
3. Ensure that all pedals, levers, and controls have adequate clearance for normal operation.
4. Ensure that all electrical components of both the ROPS and mower operate normally.
5. Ensure your door latches properly onto the striker pin. Immediately after installation, the
ROPS frame may flex slightly from installation, and the door latch will need to be re-aligned for
proper operation. Loosen the striker pin, striker mounting plate and door latch as necessary to
get a proper alignment of the door striker.
Service Parts Breakdowns:
Following are parts breakdowns for components that may require service parts replacement
during the life of the ROPS. If you require replacement parts, please contact the dealer that
you purchased the ROPS from and indicate which parts you require.

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0013 TEKT-0009 5MM Bushing 8
2 A00-0019 STEP-BOLT1-4X1 Step Bolt, 1/4" x 1", MB 4
3 A00-0021 FLANGE-NUT-1-4 Flange Nut, 1/4", YD 4
4 A00-0044 TEKT-ASM-002 Side Window Hinge Weldment 2
5 A00-0057 TEKT-0020MIR Side Window Latch, L60776 1
6 A00-0058 CARRIAGE_BOLT-5-16X1 Bolt, Carriage, 5/16"x 1", YD 1
7 A00-0059 FLANGE-NUT-5-16 Flange Nut, 5/16", YD 1
8 A00-0087 TEKT-0028 Side Window Slider Bracket 2" tube 1
9 A00-0119 WASHER_1-4 Washer, Flat, 1/4" 2
10 Ja5-0004 JA9016-056 Side Window Glass 1
11 Ja5-0013 JA9016-153_ Side Window Seal 1
1 req Left Side Window Assembly
Daryl Furkalo 2015-08-12 Imp. JA9016-ASM-15_OP
B
SCALE 0.250
1
2
3
4
5
6
7
8
9
10
11

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0013 TEKT-0009 5MM Bushing 8
2 A00-0019 STEP-BOLT1-4X1 Step Bolt, 1/4" x 1", MB 4
3 A00-0021 FLANGE-NUT-1-4 Flange Nut, 1/4", YD 4
4 A00-0046 TEKT-ASM-002R Side Window Hinge Right 2
5 A00-0056 TEKT-0020 Side Window Latch, L60775 1
6 A00-0058 CARRIAGE_BOLT-5-16X1 Bolt, Carriage, 5/16"x 1", YD 1
7 A00-0059 FLANGE-NUT-5-16 Flange Nut, 5/16", YD 1
8 A00-0087 TEKT-0028 Side Window Slider Bracket 2" tube 1
9 A00-0119 WASHER_1-4 Washer, Flat, 1/4" 2
10 Ja5-0004 JA9016-056 Side Window Glass 1
11 Ja5-0013 JA9016-153R Side Window Seal 1
1 req Right Side Window Assembly
Daryl Furkalo 2015-08-12 Imp. JA9016-ASM-15R_OP
B
SCALE 0.250
11
10
9
12
3
4
5
6
7
8

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0001 DLP-HANDLE Outside Push Button Handle 1
2 A00-0002 LEFT-LATCH Suicide Door Left Latch 1
3 A00-0013 TEKT-0009 5MM Bushing 15
4 A00-0018 STEP-BOLT1-4X1-1-2 Step Bolt, 1/4" x 1 1/2", MB 3
5 A00-0020 STEP-BOLT1-4X1-1-4 Step Bolt, 1/4" x 1 1/4", MB 4
6 A00-0021 FLANGE-NUT-1-4 Flange Nut, 1/4", YD 9
7 A00-0039 TEKT-ASM-001 Left Door Hinge Weldment, Upper 1
8 A00-0040 REID-RST-160-RST-163 Grab Handle 1
9 A00-0041 TEKTITE-DECAL Tektite Cab Decal - Solid White 1
10 A00-0118 FLANGE_BOLT_1-4X1 Flange Bolt, 1/4" x 1", YD 2
11 A00-0177 TEKT-0068 Handle Washer Spacer 1
12 A00-0228 TEKT-ASM-029 Left Door Hinge Weldment, Lower 1
13 A00-0295 FLANGE_BOLT_M6X30 Flange Bolt, M6x30, YD 1
14 Ja5-0002 JA9016-054 Left Door Glass 1
15 Ja5-0014 JA9016-154- LH Door Seal 1
16 Ja5-0015 JA9016-ASM-17 Left Door Frame Weldment 1
1 req Left Door Assembly
Daryl Furkalo 2015-08-12 Imp. JA9016-ASM-16_OP
B
SCALE 0.150
1
16
15
14
13
12
11
10
9
8
7
65
4
3

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0001 DLP-HANDLE Outside Push Button Handle 1
2 A00-0003 RIGHT-LATCH Suicide Door Right Latch 1
3 A00-0013 TEKT-0009 5MM Bushing 15
4 A00-0018 STEP-BOLT1-4X1-1-2 Step Bolt, 1/4" x 1 1/2", MB 3
5 A00-0020 STEP-BOLT1-4X1-1-4 Step Bolt, 1/4" x 1 1/4", MB 4
6 A00-0021 FLANGE-NUT-1-4 Flange Nut, 1/4", YD 9
7 A00-0040 REID-RST-160-RST-163 Grab Handle 1
8 A00-0041 TEKTITE-DECAL Tektite Cab Decal - Solid White 1
9 A00-0042 TEKT-ASM-001R Right Cab Door Hinge Weldment, Upper 1
10 A00-0118 FLANGE_BOLT_1-4X1 Flange Bolt, 1/4" x 1", YD 2
11 A00-0177 TEKT-0068 Handle Washer Spacer 1
12 A00-0229 TEKT-ASM-029R Right Door Hinge Weldment, Lower 1
13 A00-0295 FLANGE_BOLT_M6X30 Flange Bolt, M6x30, YD 1
14 Ja5-0003 JA9016-055 Right Door Glass 1
15 Ja5-0016 JA9016-ASM-19 Right Door Frame Weldment 1
16 Ja5-0017 JA9016-155- RH Door Seal 1
1 req Right Door Assembly
Daryl Furkalo 2015-08-12 Imp. JA9016-ASM-18_OP
B
SCALE 0.150
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0013 TEKT-0009 5MM Bushing 3
2 A00-0014 TEKT-0092 Thick Bushing 3
3 A00-0020 STEP-BOLT1-4X1-1-4 Step Bolt, 1/4" x 1 1/4", MB 3
4 A00-0021 FLANGE-NUT-1-4 Flange Nut, 1/4", YD 3
5 Ja5-0001 JA9016-043 Windshield Glass 1
6 Ja5-0018 JA9016-156- Front Window Seal 1
1 req Windshield Assembly
Daryl Furkalo 2015-08-12 Imp. JA9016-ASM-44_OP
B
SCALE 0.200
1
2
3
4
5
6

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0013 TEKT-0009 5MM Bushing 5
2 A00-0014 TEKT-0092 Thick Bushing 3
3 A00-0019 STEP-BOLT1-4X1 Step Bolt, 1/4" x 1", MB 1
4 A00-0020 STEP-BOLT1-4X1-1-4 Step Bolt, 1/4" x 1 1/4", MB 3
5 A00-0021 FLANGE-NUT-1-4 Flange Nut, 1/4", YD 4
6 A00-0033 315-080 Rear Wiper Shaft Grommet 1
7 A00-0043 WWF-MOTOR WWF Wiper Motor, 1" Shaft 1
8 A00-0108 TEKT-ASM-037 WWF, Adjustable Radial Arm, 15" to 19" 1
9 A00-0320 TEKT-0159 12 3/4" Wiper Blade 1
10 Ja5-0005 JA9016-058 Rear Window Glass 1
11 Ja5-0019 JA9016-157- Rear Window Seal 1
1 req Rear Window Assembly
Daryl Furkalo 2015-08-12 Imp. JA9016-ASM-45_OP
B
SCALE 0.250
1
2
3
4
5
67
8
9
10
11

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0095 TEKT-0057 ROPS Isolator 2
2 A00-0353 TEKT-0143 New Condensor Assembly, Kalori 1
3 A00-0359 FLANGE-NUT-10-32 Flange Nut, 10-32 6
4 A00-0360 SCREW-10-32X1-2 Screw, 10-32 x 1/2" 6
5 Ja5-0006 JA9016-ASM-13 Rear Bracket Weldment 1
6 Ja5-0020 JA9016-116 Rear Bracket Seal, Bottom 1
7 Ja5-0020 JA9016-117 Rear Bracket Seal Vertical 1
8 Ja5-0020 JA9016-127 RH Ndax Rear Bracket 1
Condenser/Rear Bracket Assembly
Daryl Furkalo 2015-08-12 Imp. JA9016-ASM-30_OP
B
SCALE 0.200
1
2
3
4
5

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0006 TEKT-0074 Cabin Air Filter 2
2 A00-0016 TEKT-0075 Domelight LED 1
3 A00-0017 305-1002 Panto Mount Plate 1
4 A00-0025 BALL-LOUVER 2 1/2" Ball Louver 4
5 A00-0026 OSCILLATING-FAN Oscillating Fan 1
6 A00-0038 TEKT-0076 3" Plug 1
7 A00-0055 TEKT-0019 Fir Tree Fastener 2
8 A00-0070 REID-KBP-262-KBP-265 Knob, Knurled, 1/4" 6
9 A00-0071 LEFT-SWITCHPLATE-ASM Left Switchplate Assembly 1
10 A00-0072 TEKT-ASM-030 Right Switchplate Assembly, 2014 Update 1
11 A00-0073 FILTER-COVER Filter Cover 3
12 A00-0074 TEKT-ASM-004 Fuse Block Assembly 1
13 A00-0075 WWJ-MOTOR-ASM Front Wiper Motor, WWJ 1
14 A00-0076 TEKT-0026 1/4" Panel Nut 6
15 A00-0081 KUF2880-HEADLINER-REV1 Headliner 1
16 A00-0082 KUF2880-049 Headliner Upholstery 1
17 A00-0083 KUF2880-060 Front Filter Upholstery 1
18 A00-0120 BLADE_24 Wiper Blade, 24" 1
19 A00-0140 PANTO_ARM_20 Wiper Arm, 20" Panto 1
Headliner Assembly, Mowers
Daryl Furkalo 2014-01-02 Imp. TEKT-ASM-032
B
SCALE 0.110
12
13
14
15
18
19
SCALE 0.110
1
2
16
17
3
45
6
7
8
9
10
11

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 A00-0006 TEKT-0074 Cabin Air Filter 2
2 A00-0070 REID-KBP-262-KBP-265 Knob, Knurled, 1/4" 4
3 A00-0073 FILTER-COVER Filter Cover 2
4 A00-0076 TEKT-0026 1/4" Panel Nut 4
5 Ja5-0009 JA9016-149 Rear Seal Roof Cap 1
6 Ja5-0010 JA9016-150 Front Seal Roof Cap 1
7 Ja5-0011 JA9016-151- Roof Cap Edging 1
8 Ja5-0012 JA9016-152- Roof Cap Seal, Side, 180 Bulb 1
9 Ja5-0012 JA9016-152R Roof Cap Seal, Side, 180 Bulb 1
10 Ja5-0021 JA9016-ASM-40 Roof Cap Weldment 1
1 req Roof Cap Assembly
Daryl Furkalo 2015-08-13 Imp. JA9016-ASM-42_OP
B
SCALE 0.150
1
2
3
4
5
6
7
8
9
10

Notice of Confidentiality
This material is property of Tektite Manufacturing
Inc and is not to be used by the recipient for any
purpose other than the purpose for which it was
transmitted. The material remains the property of
Tektite and shall be returned upon request. The
material may not be reproduced or disclosed to third
parties without the written consent of Tektite.
Tolerances:
Unless otherwise
specified
X.X = 1/16"
Angular = 1.0
Drawn By:
Checked By: Size:
File Name:
Units:
Date:
Date:
Req'd: Description:
Tektite Manufacturing Inc.
24157 Hwy 3, Box 639, Winkler MB, R6W 4A8, Canada
CNC:
Index Service Part #File Name Description Qty
1 JA9016-ASM-22-RADIO 1
2 A00-0021 FLANGE-NUT-1-4 Flange Nut, 1/4", YD 2
3 A00-0059 FLANGE-NUT-5-16 Flange Nut, 5/16", YD 2
4 A00-0084 TEKT-0070 Gas Shock 2
5 A00-0085 TEKT-0069 Gas Shock Stud 2
6 A00-0134 WASHER-BOTTLE Washer Tank 1
7 A00-0136 RED_TAIL_FLASH Red Tail Light 2
8 A00-0141 ROUND_MIRROR_6_INCH External 6" Mirror 2
9 A00-0143 TEKT-0083 Turn light, Amber 4
10 A00-0182 TEKT-ASM-018 Headlight 2
11 A00-0313 TEKT-ASM-050 Oct 2014 Work Light 2
1 req Accessories Assembly
Daryl Furkalo 2015-08-13 Imp. JA9016-ASM-46_OP
B
SCALE 0.120
2
11
10
9
8
7
5
4
3
6