Jacobsen SLF 1880 User manual

Technical Repair Manual
SLF 1880

Page Intentionally Blank

Technical Repair Manual
SLF 1880
!
WARNING: If incorrectly used this machine can cause sever injury. Those
who use and maintain this machine should be trained in its proper use,
warned of its dangers and should read the entire manual before attempting
to set up, operate, adjust or service the machine.
Litho in the U.S.A. 5/2011 Part Number 4171721 Rev B
©2011, Jacobsen, A Textron Company. All rights reserved.

Page Intentionally Blank

Forward
General
This manual provides detailed information and proce-
dures to safely repair and maintain the following:
Jacobsen® SLF1880™ fairway mower and associated
accessory attachments.
This manual is intended to introduce and guide the user
through the latest factory-approved troubleshooting
and repair techniques and practices.
Before you attempt to troubleshoot or make repairs,
you must be familiar with the operation of this machine.
Refer to the operator’s manual and parts manual for
specific information on these topics.
THE INFORMATION CONTAINED IN THIS MANUAL
IS BASED ON MACHINES MANUFACTURED UO TO
THE TIME OF PUBLICATION. JACOBSEN
RESERVES THE RIGHT TO CHANGE ANY OF THIS
INFORMATION WITHOUT NOTICE.
California
Proposition 65 Warning
Trademark Acknowledgement
Jacobsen acknowledges the following trademarks for
company names or products mentioned within this pub-
lication:
Lubriplate® Is a Trademark of Fiske Brothers Refining
Co.
Loctite® and Permatex® are trademarks of Henkel Cor-
poration.
WARNING
Certain vehicle components contain or emit
chemicals known to the state of California to
cause cancer and birth defects or other repro-
ductive harm.
!

Forward
How to Use This Manual
This manual is designed to provide multiple ways to
locate and access repair information.
Read each section in entirety before beginning a pro-
cedure. Proper understanding of machine operation
and components is the key to successful diagnostics
and repair.
Make use of special information features within this
manual in order to be better prepared to perform
repairs. Always follow manual procedures and safety
guidelines. Never take shortcuts.
Table of Contents
Major machine components or topics of interest are
separated into specific chapters. Each manual lists
these chapters in the main table of contents.
Chapter table of Contents
Each chapter begins with a detailed Table of Contents
related to the specific machine component or system.
Use the chapter Table of Contents to find specific com-
ponent or procedural information.
Required Tools and Material
Some procedures will require the use of specific tools
and/or materials. These tools and/or materials will be
listed for reference, prior to beginning a procedure.
Specifications
Near the beginning of each chapter is a specifications
listing. this listing contains any specifications contained
within the chapter.
Quick Reference Specifications
A list of all machine specifications can be found in
Chapter 1 “Specifications”. This is a list of all general
specifications. Detailed specifications will be listed in
the front of each chapter under “Specifications”.
Warning and Cautions
Warning and Caution indicators are located throughout
the manual at specific points of interest. These notices
are given to prevent personal injury, death and/or
equipment damage. Always heed these notices, and
practice common sense when performing any mainte-
nance or repair procedure.
Notes
Special notes are given in order to draw attention to
detailed instructions. These notes are intended to give
further important information regarding the machine
and/or a step in a procedure.
Troubleshooting
Troubleshooting charts are provided in each chapter to
aid in the diagnostic process. Use these suggestions to
aid in identifying a potential mechanical or machine
adjustment problem.
Copyright 2011 Textron Inc.
“All rights reserved, including the right to reproduce this manual or portions thereof in any form.”

INTRODUCTION
CONTROLS
ENGINE
DRIVE TRAIN
BRAKE SYSTEM
STEERING
WHEELS AND TIRES
HYDRAULICS
CHASSIS
ELECTRICAL SYSTEM
PREVENTIVE MAINTENANCE
ATTACHMENTS
OPTIONS
MISCELLANEOUS
1
2
3
4
5
6
7
8
9
10
11
12
13
14

Page Intentionally Blank

INTRODUCTION
--1
SECTION 1
INTRODUCTION
1A General Information ........................................................................................................................................ 1
Contents................................................................................................................................................... 1
Index Numbers......................................................................................................................................... 1
Replacement Parts................................................................................................................................... 1
Specifications ........................................................................................................................................... 2
Serial Numbers ........................................................................................................................................ 4
General Cleaning ..................................................................................................................................... 4
Safety ....................................................................................................................................................... 4
Torque Values ........................................................................................................................................ 10
1

INTRODUCTION
-0
Page Intentionally Blank