Jandy JE User manual
H0408600 Rev B
Jandy® Pro Series
JE Heat Pump
WARNING
This product must be installed by a licensed HVAC technician certied in heat
pump repair and maintenance by the jurisdiction in which the product will be installed where such
state or local requirements exists. The technician must possess and comply with all certications and
regulations regarding the purchasing, handling, transportation and reclamation of R410A refrigerant.
In the event no such state or local requirement exists, the installer or maintainer must be a
professional with sufcient experience in pool equipment installation and maintenance so that all of
the instructions in this manual can be followed exactly. Before installing this product, read and follow
all warning notices and instructions that accompany this product. Failure to follow warning notices
and instructions may result in property damage, personal injury, or death. Improper installation and/
or operation can create an electrical hazard which can cause serious injury, property damage, or
death. Improper installation and/or operation will void the warranty.
Page 1
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
1.1 Introduction .........................................................3
1.2 Consumer Information and Safety ......................3
1.3 Warranty ............................................................. 4
1.4 Codes and Standards .........................................4
1.5 Technical Assistance ........................................... 4
1.6 Materials Needed For Installation .......................4
1.7 Specifications ...................................................... 5
2.1 General Information ............................................ 5
2.2 Location Requirements ....................................... 5
3.1 Plumbing Layout ................................................ 8
3.2 Water Connections at Heat Pump ...................... 8
3.3 Check Valve Installation ......................................8
3.4 Multiple Unit Installation ...................................... 9
4.1 General Information ............................................ 9
4.2 Main Power ....................................................... 10
4.3 Bonding ............................................................. 15
4.4 Optional Remote Controls ................................15
5.1 Initial Start-up Precautions ................................ 18
5.2 Operating the Controller ...................................18
Figure 1. Zodiac® JE Heat Pumps Dimensions .........7
Figure 2. Anchor Clamp Positions .............................9
Figure 3. Anchor Clamp Installation ..........................9
Figure 4. Standard Plumbing Layout ....................... 11
Figure 5. Plumbing For Heating System
Combinations ........................................... 11
Figure 6. Two (2) Heat Pump Plumbing Layout ......12
Figure 7. Four (4) Heat Pump Plumbing Layout .....12
Figure 8. JE Single-Phase Electrical Supply
Wiring Diagram ........................................13
Figure 9. JE 3-Phase Electrical Supply Wiring
Diagram ...................................................14
Figure 10. JE Heat Pump Front View ........................15
Figure 11a. Remote Pool-Off-Spa Connection
(3-Wire Connection) .................................16
Figure 11b. AquaLink RS or Remote TSTAT
Connection (2-Wire Connection) ..............16
Figure 12. AquaLink® RS to JE Heat Pump ..............17
Figure 13. JE Heat Pump Connection to Power
Center ......................................................18
5.3 Operating Features of Hybrid Units with
Optional Chiller ................................................. 19
5.4 User Setup Options ..........................................20
5.5 Set Point Lockout .............................................. 21
5.6 Water Pressure Switch Adjustment ................... 21
6.1 Water Chemistry ............................................... 21
6.2 Winterizing ........................................................ 22
6.3 Spring Start-Up ................................................. 22
6.4 Inspection and Service .....................................22
7.1 Heat Pump Design ............................................ 23
7.2 Heat Pump Components and Operation ........... 23
8.1 Troubleshooting Guide......................................25
8.2 Diagnostics ....................................................... 25
9.1 Ordering Information ......................................... 26
9.2 Zodiac JE Heat Pumps Parts List ..................... 26
9.3 Zodiac JE1500 Heat Pumps Exploded View ... 27
9.4 Zodiac JE2000 Heat Pumps Exploded View ... 28
9.5 Zodiac JE Single Phase Electric Box ................ 29
9.6 Zodiac JE Three Phase Electric Box ................ 29
Figure 14. Main Control Panel ..................................20
Figure 15. Winterizing the JE Heat Pump .................22
Figure 16. Zodiac JE1500 Heat Pumps Exploded
View (JE1500 Shown) ..............................27
Figure 17. Zodiac JE2000 Heat Pumps Exploded
View (JE2000 Shown) ..............................28
Figure 18. Zodiac JE Heat Pump Single Phase
Electric Box ..............................................29
Figure 19. Zodiac JE Heat Pump Three Phase
Electric Box ..............................................29
Table 1. JE Heat Pump Technical
Specifications .............................................6
Table 2. Heat Pump Clearances ..............................7
Table 3. Optimal Water Chemistry Ranges ............23
Table 4. Heat Pump Troubleshouting Guide ..........24
Table 5. Heat Pump Diagnostics ...........................25
Page 2 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
Page 3
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
The U.S. Consumer Product Safety Commission
warns that elevated water temperature can
be hazardous. Consult heater operation and
installation instructions for water temperature
guidelines before setting temperature.
The following “Safety Rules for Hot Tubs,”
recommended by the U.S. Consumer Product
Safety Commission, should be observed when
using the spa.
Spa or hot tub water temperature should never
exceed 104°F (40°C). One hundred degrees
Fahrenheit (100°F [38°C]) is considered safe for
a healthy adult. Special caution is recommended
for young children.
The drinking of alcoholic beverages before or
during spa or hot tub use can cause drowsiness
which could lead to unconsciousness, and
subsequently result in drowning.
Pregnant women take note!
“Fresh water swimming pools and spas” include
systems that utilize saltwater chlorine generator
units, such as the Zodiac AquaPure® Electronic
Chlorine Generator. Please ensure that the salt
content of the pool/spa does not exceed
4500 ppm and water ow rate is within
30-70 gpm (110-265 lpm).
After installation, these
instructions must be given to
the homeowner or left on or
near the heat pump.
This manual contains
important information that
will help you in operating and
maintaining this heat pump.
Please retain it for future
reference.
Page 4 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
more economical
not
or
all
Page 5
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
Flex conduit is recommended for connecting
the electrical supply wires to the heat pump so
that the front panel may be removed easily for
servicing.
must
Plastic 2” PVC (Unions included)
Maximum
Optimum
Minimum
70 gpm (265 lpm)
60 gpm (230 lpm)
20 gpm (76 lpm)
75 psi
Voltage Requirements
1-Phase
3-Phase
230 VAC 60Hz
230 VAC 60Hz
(Model dependent)
600 PSI
Indoor installations require special
considerations for condensate drainage and
venting the cold air produced by the heat
pump. Contact the Zodiac technical support
department at (800) 822-7933.
When pool equipment is located below the pool
surface, a leak from any component can cause
large scale water loss or ooding. Zodiac cannot
be responsible for such water loss or ooding or
resulting damage.
Page 6 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
VOLTAGE 230V/60HZ 230V/60HZ 230V/60HZ 208/230V/60HZ/3 230V/60HZ 208/230V/60HZ/3
OUTPUT* 72,000 BTUs 108,000 BTUs 119,000 BTUs 137,000 BTUs
INPUT* 3.83 kW 5.03 kW 5.34 kW 6.37 kW
COP* 5.5 6 6.2 6.3
OUTPUT, STANDARD RATING CONDITIONS** 67,000 BTUs 92,000 BTUs 106,000 BTUs 127,000 BTUs
COP, STANDARD RATING CONDITIONS** 5.2 5.7 5.6 6.0 5.9 6.0 5.9
OUTPUT, LOW AMBIENT** 46,000 BTUs 64,000 BTUs 74,000 BTUs 86,000 BTUs 86,000 BTUs
COP, LOW AMBIENT** 4.0 4.0 4.0 4.2 4.0 4.2 4.0
RLA (RUNNING LOAD AMPS) 19.87A 30.77A 32.05A 23.21A 32.05A 25.00A
LRA (LOCKED ROTOR AMPS) 105A 178A 148A 164A 185A 164A
MINIMUM CIRCUIT AMPACITY 26.14A 40.21A 41.81A 30.76A 41.81A 33.0A
MAX OVER CURRENT PROTECTION*** 45A 60A 60A 45A 60A 50A
HEAT EXCHANGER Titanium
COMPRESSOR Reciprocating Scroll Scroll Scroll
CABINET ABS
REFRIGERANT 64 Oz, R410A 78 Oz, R410A 78 Oz, R410A 78 Oz, R410A 118 Oz, R410A 126 Oz, R410A 118 Oz, R410A 126 Oz, R410A
REFRIGERANT HIGH PRESSURE ALARM 600 PSI (reset to 460 PSI)
REFRIGERANT LOW PRESSURE ALARM -
HEATING UNITS
58 PSI (reset to 127 PSI)
REFRIGERANT LOW PRESSURE ALARM -
REVERSE UNITS
35 PSI (reset to 74 PSI)
LOW WATER FLOW ALARM 20 GPM
MAXIMUM HEIGHT BELOW WATER LEVEL 10 feet below pool level
MINIMUM HEIGHT ABOVE WATER LEVEL 5 feet above pool level
OPTIMAL WATER FLOW 30 GPM 42 GPM 48 GPM 48 GPM 57 GPM 57 GPM
MINIMUM WATER FLOW 20 GPM
MAXIMUM WATER FLOW 70 GPM
AIR FLOW 2100 CFM 3600 CFM
WATER TEMPERATURE DIFFERENTIAL (DELTA
T)
Adjustable between 1°F to 5°F
UNION SIZE 2”
WEIGHT 175 lbs 220 lbs 223 lbs 223 lbs 228 lbs 230 lbs 228 lbs 230 lbs
* Test Conditions: 80˚ F Air, 80% RH, 80˚ F Water, Outside the scope of AHRI Standard 1160 (I-P)
** Rated in accordance with AHRI Standard 1160 (I-P)
*** Max Over Current Protection refers to the maximum breaker size allowed. If this value is not a standard breaker size, use the next smallest standard size breaker.
The breaker size must not be smaller than the Minimum Circuit Ampacity value.
Page 7
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
3.5"
8"
B
A
C
F
E
D
MODEL SIZE DIMENSIONS
A B C D E F
JE1500T 33” 34” 12.5” 9” 7” 39”
JE2000/2500T 36” 40” 13.8” 19” 15” 43”
JE3000T 36” 44” 13.8” 19” 15” 43”
Ensure that the pad is pitched not more than ¼
inch per foot cm per toward the compressor end
(front) of the heat pump. Pitch slab from back to
front ¼ inch per foot maximum and level from
side to side.
Side of
Heat
pump
Minimum Clearances for
Operation
Recommended Clearances
for Serviceability
Inches Centimeters Inches Centimeters
Front 24 60 36 90
Rear 12 30 24 60
Left 12 30 24 60
Right 12 30 24 60
Top 60 150 60 150
Clearances listed in Table 2 are manufacturer’s tested values.
These are given as minimum values. Where local and national codes
apply, and values are different than those listed in Table 2, use the
greater value to ensure safe and proper operation.
Page 8 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
Pool > Pool Pump > Filter > Heat Pump > Check
Valve > Chemical Loop > Chlorinator > Pool
For normal installations, do not install a shutoff
valve or any kind of variable restriction in the
water piping between the heat pump outlet and
the pool/spa.
Shipping plugs have been installed in the water inlet
and outlet ports of the heat pump at the factory.
Before installing any plumbing, remove the shipping
plugs.
Make sure that ow requirements and pool
water turn over rates can be maintained with
the installation of additional heat pumps and
plumbing restrictions.
A check valve can interfere with the proper
operation of certain Suction Vacuum Release
System (SVRS) products. To avoid possible
entrapment hazard, serious injury, or death,
make sure to review the operation/owners
manual of your particular SVRS product
before installing the check valve.
Page 9
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
It may be necessary to adjust water pressure
switch if a unit is installed below the water level.
See Section 5.6 for details on when and how to
adjust the pressure switch.
Each heat pump allows a maximum ow rate of
70 gpm (265 lpm) and requires a minimum of
20 gpm (76 lpm).
4" MIN
2 1/2" MIN
CONCRETE
EQUIPMENT PAD
1/4" X 1 3/4"
GALVANIZED OR PLATED
CONCRETE SCREW
(MANUFACTURER PROVIDED)
HEAT PUMP
ANCHOR
BRACKET
3/16" DRILLED HOLE
#10 X 5/8"
STAINLESS STEEL SCREW
NOTE: DO NOT DRILL INTO
EVAPORATOR COIL TUBES
EVAPORATOR
COIL
HEAT PUMP
PLASTIC BASE
ATTACH ANCHOR BRACKETS
TO BASE OF HEAT PUMP
WHERE INDICATED
Page 10 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
This heat
pump contains wiring that carries high voltage.
Contact with these wires may result in severe
injury or death. Disconnect power circuit before
connecting the heat pump
Label all wires prior to disconnection when
servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper
operation after servicing.
Page 11
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
AquaPure
POOL PUMP
FILTER
FROM POOL OR SPA
CHEMICAL FEEDER
TO POOL OR SPA
CHECK VALVE
OR OPTIONAL CHLORINE
GENERATION SYSTEM
(JANDY AQUAPURE
®
SHOWN)
MANUAL BYPASS VALVE
CHEMICAL LOOP
POOL HEATER
VENT FOR INDOOR
INSTALLATION ONLY
Page 12 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
Flow Meter
Pool pump
NOTE! Gate Valves are
optional on heater inlets
but will help system
balancing
Extend 12" past
end heater inlet
for hydraulic
balancing
2" pvc pipe
12 inches min. clearence around evap.
12"
Flow Meter
To Pool
Minimum 2" pvc
pipe
2" Gate Valve Bypass
OPTIONAL
2" pvc
Heater 1
Front of
Heater 2
Front of
Heater 3
Optional
Isolation Valves
From Filter
Manual Bypass Valve
2” PVC
3” PVC
Optional
Isolation Valves
From Filter
To Pool
Manual Bypass Valve
Optional
Isolation Valves
From Filter
To Pool
2” PVC
3” PVC
Page 13
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
COMPRESSOR
CAPACITOR
FAN
CAPACITOR
24 VAC
TRANSFORMER
POWER
INTERFACE
W
BK
WATER PRESSURE
SWITCH
CONTACTOR
FAN RELAY
COMPRESSOR
BK
R
BL
R
BK
BL
BK
BK
BR
W
BL
Y
Y
BL
W
BR
HIGH REFRIGERANT
PRESS SWITCH
LOW REFRIGERANT
PRESS SWITCH
WATER
TEMP
DEFROST
TEMP
BK
R
R
L1
L2
Y
Y
Y
Y
BK
W
R
R
FAN MOTOR
BR
BR/W
BK
W
W
W
W
W
R
R
GROUND
GR
GR
R
REVERSING VALVE
(OPTIONAL)
BL
HARD START
CAPACITOR
(OPTIONAL)
BK
BK
BK
BK
FACTORY INSTALLED 208/230 VAC
FIELD INSTALLED 208/230 VAC
FACTORY 24 VAC HARNESS
FACTORY OPTIONAL 24 VAC
FACTORY OPTIONAL 208/230 VAC
JE SERIES
230 VAC
SINGLE PHASE
60 Hz
WIRING DIAGRAM
JE 3000TR & JE3000TR3 ONLY
Page 14 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
BK
BR
W
BL
Y
BL
BK
BL
BL
Y
Y
BL
R
BK
R
BK
BL
BL
R
BK
Y
Y
BK
W
W
BK
BK
BK
BL
R
BR
BR/W
BK
R
BK
GR
GR/Y
GROUND
POWER BOARD
COMPRESSOR
FAN MOTOR
WATER PRESSURE
SWITCH
USER INTERFACE
REVERSING
VALVE
(OPTIONAL)
HIGH REFRIGERANT
PRESSURE SWITCH
LOW REFRIGERANT
PRESSURE SWITCH
CONTACTOR
W
W
W
WW
L1
L2
L3
FAN CAPACITOR
FAN
RELAY
WATER
TEMP
DEFROST
TEMP
SENSOR
R
Y
Y
W
Y
W
FACTORY OPTIONAL 24 VAC
FACTORY 24 VAC HARNESS
FIELD INSTALLED 208/230 VAC
FACTORY INSTALLED 208/230 VAC
JE SERIES
230 VAC
THREE PHASE
60 Hz
WIRING DIAGRAM
JE 3000TR & JE3000TR3 ONLY
Page 15
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
SERVICE ACCESS
PANEL (5 SCREWS)
CONNECTOR FOR
HIGH VOLTAGE WIRES
CONNECTOR FOR
LOW VOLTAGE WIRES
This heater must be connected to a bonding
grid with a solid copper wire not smaller in
diameter than 8 AWG (In Canada, it shall be no
smaller than 6 AWG.)
The display will revert back to after one
minute since the last key press.
Page 16 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
The display will revert back to after one
minute since the last key press.
Only a revision “N”, or higher, program chip in
the RS system will support the
heat pump interface.
Page 17
ENGLISH
Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
Heat Pump
Green - Enabled
Red - On Heat Pump Connections
Terminals 1 and 2
Connector for Low
Voltage Wires
DIP Switches
S1 and S2
S1
S2
RESET
SERVICE
TIME OUT
FILTER PUMP
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
RS6 & RS8 ONLY
RS8 ONLY
HEATER SOLAR
POOL MODE
SPA MODE
SPA DRAIN
SPA FILL
AUTO
6 5 4 3 2 1
10987654321
4 3 2 1 4 3 2 1
S1
S2
OFF ON
OFF ON
1 2 3 4 5 6 7 8
1 2 3 4
Thu January, 2009 3:03 PM
AquaLink Touch
Home
Menu OneTouch Help Back Status Photos Power
FILTER
PUMP
SPA POOL
HEAT
Pool Temp
86º Air Temp
78º
SPA
HEAT
AUX1 AUX2 AUX3 Other
Devices
On/Off
Green - Enabled
Red - On
If you need to install more than two (2) wires in
each terminal, order a Zodiac® Multiplex PCB
Kit, which includes the Multiplex Board (Zodiac
Part No. 6584). Never put more than two (2)
wires into each of the pins of the terminal bar.
If connecting more than two (2) items to the RS
Power Center red, 4-pin connector, a Multiplex
PCB is required.
Page 18 ENGLISH Jandy® Pro Series JE Heat Pumps | Installation and Operation Manual
1234
RED
BLK
YEL
GRN
®
JANDY AquaLink RS
FILTER PUMP OFF
AIR 79°
06/26/04 MON
6:00 PM
EQUIPMENT ON/OFF
ONETOUCH ON/OFF
MENU / HELP
OR
4-Conductor
Wire
Jandy Pro Series JE Heat Pump Power Interface
OPTIONAL
4321
RED
BLK
YEL
GRN
RS Power
Center
S1
S2
RESET
SERVICE
TIME OUT
FILTER PUMP
AUX 1
AUX 2
AUX 3
AUX 4
AUX 5
AUX 6
AUX 7
RS6 & RS8 ONLY
RS8 ONLY
HEATER SOLAR
POOL MODE
SPA MODE
SPA DRAIN
SPA FILL
AUTO
6 5 4 3 2 1
10 9 8 7 6 5 4 3 2 1
4 3 2 1 4 3 2 1
OR
Thu January, 2009 3:03 PM
AquaLink Touch
Home
Menu OneTouch Help Back Status Photos Power
FILTER
PUMP
SPA POOL
HEAT
Pool Temp
86º
Air Temp
78º
SPA
HEAT
AUX1 AUX2 AUX3
Other
Devices
On/Off
Do not use this heat pump if any part has
been under water. Immediately call a qualied
service technician to inspect the heater and
replace any part of the control system which
has been under water.
Keep all objects off the top of the heat pump.
Blocking air ow could damage the unit and
may void the warranty.
XXX represents the current temperature setting
on the control. The default setting for pool
temperature is 80°F (26°C).
and
.
.
,
.
This manual suits for next models
1
Table of contents
Languages:
Other Jandy Heat Pump manuals
Popular Heat Pump manuals by other brands
Supreme Heating
Supreme Heating HEATSEEKER VORTEXPRO 10 KW Installation & user manual
Bosch
Bosch Compress Hybrid 7000i AW installation manual
Daikin
Daikin VRV reference guide
Graco
Graco HIGH-FLO 311211L Instructions - parts
Nibe
Nibe Fighter 200P Installation and maintenance instructions
Electra
Electra Monoblock 7 Service manual
Olimpia splendid
Olimpia splendid Sherpa Monobloc 4 Instructions for installation, use and maintenance
Viessmann
Viessmann Vitocal 200-S Installation and service instructions
Rinnai
Rinnai EHP32 Operation and installation guide
Carrier
Carrier 38AUQ 25 Series Installation, Start-Up and Service Instructions
AZURO
AZURO BP-50WS-C Installation and Maintenance
Airwell
Airwell CKD Series Service manual
