Janome Decor Excel II 5024 User manual

AAASewing.com
INSTRUCTION BOOK
Janome Decor Excel 5024
Instruction Manual
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety precautions should always be followed, including the
followings:
Read all instructions before using this appliance.
DANGERÑ To reduce the risk of electric shock:
1. An appliance should never be left unattended when plugged in. Always unplug this sewing machine
from the electric outlet immediately after using and before cleaning.
2. Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 15 Watts.
WARNINGÑ To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or
near children.
2. Use this appliance only for its intended use as described in this ownerÕs manual.
Use only attachments recommended by the manufacturer as contained in this ownerÕs manual.
3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it
has been dropped or damaged, or dropped into water.
Return this sewing machine to the nearest authorized dealers or service center for examination,
repair, electrical or mechanical adjustment.
4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing
machine and foot controller free from accumulation of lint, dust and loose cloth.
5. Never drop or insert any object into any opening.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
8. To disconnect, turn all controls to the off (Ò0Ó) position, then remove plug from outlet.
9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
10. Keep fingers away from all moving parts. Special care is required around the sewing machine
needle.
11. Always use the proper needle plate. The wrong plate can cause the needle to break.
12. Do not use bent needles.
13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
14. Switch this sewing machine off (Ò0Ó) when making any adjustment in the needle area, such as
threading the needle, changing the needle, threading the bobbin or changing the presser foot, and
the like.
15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or
when making any other adjustments mentioned in this ownerÕs manual.
SAVE THESE INSTRUCTIONS
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
1
Table of Contents
Names of Parts ....................................................2
Detachable Extension Table.................................3
Accessory Storage Compartment ........................4
Connecting Machine to Power Supply .................5
Foot Control .........................................................5
Sewing Light.........................................................6
¥ To replace the light bulb ................................6
Pressure Dial........................................................6
To Raise or Drop the Feed Dog ...........................6
To Remove and Attach Presser Foot ...................7
To Remove and Attach the Foot Holder ...............7
Reverse Button ....................................................7
Presser Foot Lifter................................................7
Changing Needle .................................................8
Choose Your Needle and Thread.........................8
Winding the Bobbin ..............................................9
¥ Set the Spool.................................................9
¥ Removing the Bobbin.................................... 9
¥ Winding the Bobbin .....................................10
¥ Inserting the Bobbin .................................... 11
Threading the Machine ......................................12
¥ Needle Threader .........................................13
¥ Drawing Up the Bobbin Thread................... 14
Adjust the Top Thread Tension...........................15
¥ Choose the Correct Tension........................15
¥ Tension is too tight.......................................15
¥ Tension is too loose.....................................15
Pattern Selector Dial ..........................................16
Zigzag Width Control..........................................16
Stitch Length Control..........................................16
Infinite Needle Position ......................................16
Straight Stitching ................................................17
¥ Starting to Sew............................................17
¥ Changing Sewing Direction......................... 17
¥ Finishing Sewing .........................................17
Sewing on Heavy Fabrics .................................. 18
Seam Allowance Lines ....................................... 18
Turn a Square Corner ........................................18
Zigzag Stitching..................................................19
Overcasting ........................................................19
Overedge Stitch .................................................20
Tricot Stitch ........................................................20
Triple Strength Stitch..........................................21
Outline Stretch Stitch .........................................21
Sewing Buttons ..................................................22
Automatic Buttonhole ...................................23Ð25
¥ To Alter the Stitch Density ...........................25
Corded Buttonhole .............................................26
Zipper Sewing ..............................................27Ð28
¥ To Snap On the Zipper Foot ........................27
¥ Fabric Preparation.......................................27
¥ To Sew...................................................27Ð28
Rolled Hem ........................................................29
Blind Stitch Hemming.........................................30
Decorative Satin Stitch Patterns ........................31
Stretch Stitch Patterns .......................................31
Adjusting Stretch Stitch Balance ........................32
Smocking ...........................................................32
Quilting ...............................................................33
Pin Tucking......................................................... 33
Shell Tuck...........................................................34
Fagoting .............................................................34
AppliquŽ .............................................................35
Patch Work.........................................................35
Scallop Hems .....................................................36
Elastic Stitch.......................................................36
Care of Your Machine.........................................37
¥ Cleaning the Hook Race and
Feed Dog ....................................................37
¥ Replacing the Bobbin Holder ......................37
Troubleshooting ........................................... 38Ð39
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
2
1
2
3456
7
8
9
10
11
12 13
14
15
16
17
18
19
20 21
22
23
24
25
26
Names of Parts
1. Stitch length control
2. Zigzag width control
3. Foot storage compartment
4. Flip-top sewing instruction panel
5. Top cover
6. Thread tension dial
7. Pressure dial
8. Face plate
9. Thread cutter
10. Needle threader
11. Hook cover plate
12. Hook cover plate release button
13. Extension table (Accessory storage box)
14. Reverse button
15. Needle clamp screw
16. Presser foot
17. Handwheel
18. Pattern selector dial
19. Feed balance dial
20. Power switch
21. Machine socket
22. Drop feed lever
23. Buttonhole lever
24. Presser foot lifter
25. Thread take-up lever
26. BH pitch balance adjusting dial
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
3
Detachable Extension Table
For Free Arm Sewing
To remove, lift out the extension table toward you as
illustrated.
Advantages of free arm sewing:
* Avoid fabric bunching around the needle
when bar tacking to reinforce pockets,
plackets and waistlines.
* For stitching sleeves, waistbands, pants legs,
or any circular garment area.
* For darning socks or mending knees,
elbows,or areas of wear in childrenÕs
clothes.
For Flat-bed Sewing
Position the tabs on the base grooves and push
down gently.
Extension table
Tabs
Base grooves
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
4
LG
D
C
F
AE
123
4
5
6
7
8
9
10 11
12
13
14
15 16 17
18
19
Accessory Storage Compartment
1. Set of needles
2. L: Quilter
3. G: Blind stitch hem foot
4. D: Hemmer foot
5. E: Zipper foot
6. A: Zigzag foot
7. F: Satin stitch foot
8. C: Overedge foot
9. Extension table
Open the extension table toward you for a
convenient place to store your accessories.
10.Screwdriver
11. R: Automatic buttonhole foot
12.Lint brush
13.Bobbin
14.Seam ripper
15.Large spool holder
16.Small spool holder
17.Additional spool pin
18.Spool pin felt
Other
19.Foot control
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
5
¥ Foot Control
Sewing speed can be varied by the foot
control.
The harder you press on the control, the faster
the machine runs.
Connecting Machine to Power Supply
Power supply plug Power switch
Outlet Machine socket
Machine plug
Before connecting the power cord, make sure the
voltage and frequency shown on the machine con-
form to your electrical power.
1. Turn off the power switch .
2. Insert the machine plug into the machine
socket .
3. Insert the power supply plug into the outlet .
4. Turn the power switch to turn on the power
and sewing light.
For Your Safety
1. While in operation, always keep your eye on
the sewing area, and do not touch any moving
parts such as the thread take-up lever,
handwheel or needle.
2. Always turn off the power switch and unplug
from the power supply:
* When leaving the machine unattended.
* When attaching or removing parts.
* When cleaning the machine.
3. Do not place anything on the foot control,
except in use.
Operating Instructions:
The symbol Ò0Ó on a switch indicates the ÒoffÓ posi-
tion.
ÒFor appliances with a polarized plug (one blade
wider than the other).
To reduce the risk of electric shock, this plug is in-
tended to fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician to
install the proper outlet. Do not modify the plug in any
way.Ó
ÒFoot Controller Model 21245 for use with Sewing
Machine Model 5124Ó
(For U.S.A market only).
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
6
Pressure Dial
The pressure dial should be set at Ò3Ó for regular
sewing. Reduce the pressure to Ò2Ó for appliquŽ,
cutwork, drawn work, basting and embroidery.
Set the pressure to Ò1Ó when sewing chiffon, lace,
organdy and other fine fabrics. Velours and knits with
a lot of stretch may also require a Ò1Ó setting.
Pressure dial
Setting mark
To Raise or Drop the Feed Dog
¥ For button sewing, etc., drop the feed dog.
¥ After finished sewing, raise the feed dog.
The feed dog must always be up for normal sewing.
Lowered position
Raised position
(120V)
(A)
(240V)
(B)
Sewing Light
Nornally, the sewing light comes on when you turn on
the main switch.
However, if you prefer to have the sewing light off
while sewing, you can open the face plate and ac-
cess the bulb on/off knob.
Face plate
Switch knob
¥ To replace the light bulb
NOTE: Unplug the power supply before
changing the light bulb.
CAUSION: As the light bulb be HOT, protect your
fingers when you handle it.
(A) To remove........ Turn to the left.
To replace........ Turn to the right.
(B) To remove........ Push and twist to the left.
To replace........ Push and twist to the right.
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
7
To Remove and Attach Presser Foot
Press the red button on the back of the foot holder.
The presser foot will drop off.
Place the selected presser foot so the pin on the foot
lies just under the groove of the foot holder. Lower
the presser bar to lock the foot in place.
Red button
Groove
Pin
To Remove and Attach the Foot Holder
To Remove:
Remove the thumb screw by turning the screw
counter-clockwise with the screwdriver.
Thumb screw
To Attach:
Match the hole in foot holder with the threaded
hole in the presser bar.
Fit the thumb screw into the hole.
Tighten the screw by turning it clockwise.
Foot holder
Presser bar
Reverse Button
For as long as you keep the reverse stitch
button depressed, the machine sews
backwards.
Reverse button
Presser Foot Lifter
The presser foot lifter raises and lowers your presser
foot.
You can raise it about 0.6 cm (1/4Ó) higher than the
normal up position for easy removal of the presser
foot or to help you place heavy fabric under it.
Presser foot lifter
Normal up position
High position
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
8
Changing Needle
Raise the needle by pressing the up/down
needle position button and lower the presser
foot.
Turn off the power switch.
Loosen the needle clamp screw by turning it
counterclockwise.
Remove the needle from the clamp.
Insert the new needle into the needle clamp
with the flat side to the rear.
When inserting the needle into the clamp,
push it up as far as it will go and tighten the
clamp screw firmly.
To find a good needle, put the flat side of the
needle onto something flat (a needle plate,
glass, etc.).
The gap between the needle and the flat
surface should be consistent. Never use a
bent or blunt needle.
Needle clamp screw
Pin
Needle clamp
Choose Your Needle and Thread
LIGHT
WEIGHT
MEDIUM
WEIGHT
HEAVY
WEIGHT
FABRICS
Crepe de Chine,
Voile, Lawn,
Organdy,
Georgette, Tricot
Linens, Cotton,
Pique, Serge,
Double Knits,
Percale
Denim, Tweed,
Gabardine, Coating,
Drapery, and
Upholstery Fablic
THREADS
Fine Silke
Fine Cotton
Fine Synthetic
Fine Cotton Covered
Polyester
50 Silk
50 to 80 Cotton
50 to 60 Synthetic
Cotton-covered
Polyester
50 Silk
40 to 50 Cotton
40 to 50 Synthetic
Cotton Covered
Polyester
NEEDLE SIZE
9 or 11
11 or 14
14 or 16
NOTE:
* In general, fine threads and needles are used for sewing thin fablics, and thicker threads and needles
are used for sewing heavy fablics.
Always test thread and needle size on a small piece of fabric which will be used for actual sewing.
* Use the same thread for needle and bobbin.
* When sewing stretch, very fine fabrics and synthetics, use a blue tipped needle.
The blue tipped needle effectively prevents skipped stitches.
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
9
Winding the Bobbin
¥ Set the Spool
Lift up the spool pin and place the spool of thread on
it with the thread coming off the spool as shown.
Press the large spool holder firmly against the spool
of thread.
* The small spool holder is used with small or
narrow spools of thread.
Spool pin
Ordinary spool
Large spool holder
Small spool holder
Small spool
¥ Removing the Bobbin
Gently slide the hook cover plate release button to
the right and remove the cover plate.
Lift out the bobbin.
Hook cover plate release button
Hook cover plate
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
10
¥ Winding the Bobbin
Lift up the spool pin. Place the spool of thread
on the spool pin with the thread coming off
the spool as shown.
Attach the large spool holder, and press it
firmly against the spool of thread.
* The small spool holder is used with narrow
or small spools of thread.
* To use the additional spool pin, guide the
upper thread as shown in , .
Guide the thread around the thread guide.
Pass the thread through the thread guide.
Thread through the hole in the bobbin from
the inside to outside. Put the bobbin on the
bobbin winder spindle.
Push the bobbin to the right.
A red light on the front panel will come on.
With the free end of the thread held in your
hand, depress the foot control. Stop the
machine when it has made a few turns, and
cut the thread close to the hole in the
bobbin.
Depress the foot control again. When the
bobbin is fully wound, it will stop automatically.
Return the bobbin winder to its original
position by moving the spindle to the left, and
cut the thread as shown.
* The machine will not sew until the spindle is
in the left position.
Spool pin
Spool
Spool holder
Additional spool pin
Felt
Additional spool pin hole
Bobbin winder spindle
7
7
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
11
¥ Inserting the Bobbin
Place the bobbin in the holder with the
thread running off counterclockwise.
End of thread
Guide the thread into the notch on the
front side of the bobbin holder.
Draw the thread to the left, sliding it between
the tension spring blades.
Notch
Continue to draw the thread lightly until the
thread slips into notch .
Pull out about 15 cm (6Ó) of thread.
Notch
Attach the hook cover plate.
Check the threading by referring to the chart
shown on the hook cover plate.
Threading chart
10
1/8 3/8 5/8
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
12
Threading the Machine
* Raise the presser foot lifter.
* Press the up/down needle position button
twice to raise the needle.
Presser foot lifter
Lead the thread from the spool and pass it
through the thread guide. Then draw it down
along the right slot.
Thread guide
Then, down around the check spring holder.
Check spring holder
Firmly draw the thread from right to left over
the take-up lever and down into the take-up
lever eye.
Thread take-up lever
Slide the thread behind the needle bar
thread guide on the left.
Thread the needle from front to back or use
the needle threader.
Needle bar thread guide
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
13
¥ Needle Threader
Raise the needle to its highest position.
Pull down the needle threader knob as far as
it will go.
Turn the knob in the direction of the arrow in
the illustration, then insert Hook into the
needle eye.
Lead the thread around Guide and under
Hook .
Turn the knob in the direction of the arrow in
the illustration, drawing the thread loop
through the needle.
Pull the thread through the needle eye.
* The needle threader can be used with a
#11 to #16 needle or a Janome Blue Tip
needle. Thread size 50 to 100 should also
work well.
Hook
Guide
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
14
¥ Drawing Up the Bobbin Thread
Raise the presser foot. Hold the needle thread
lightly with your left hand.
Press the up/down needle position button
twice to pick up the bobbin thread.
Draw up the needle thread together with a
loop of bobbin thread.
Slide 10 cm (4Ó) of both threads to the back
under the presser foot.
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
15
43
5
43
5
43
5
Adjust the Top Thread Tension
¥ Choose the Correct Tension
For Straight Stitch:
The ideal straight stitch will have threads locked
between the two layers of fablic, as shown left (mag-
nified to show detail).
If you look at the top and bottom of the seam, you will
notice that there are no gaps; that each stitch is
smooth and even.
When adjusting the top thread tension, the higher the
number, the tighter the top thread.
Results depend on;
* stiffness and thickness of the fabric
* number of fabric layers
* type of stitch
Needle thread (Top thread)
Bobbin thread (Bottom thread)
Right side of fabric
Wrong side of fabric
To loosen
To tighten
¥ Tension is too tight
The bobbin thread shows through on the right side of
the fabric and it will feel bumpy.
Turn the dial to the left to loosen the top thread
tension.
Right side of fabric
Wrong side of fabric
To loosen
¥ Tension is too loose
The top thread shows through on the wrong side of
the fabric and it will feel bumpy.
Turn the dial to the right to tighten the top thread
tension.
Right side of fabric
Wrong side of fabric
To tighten
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
16
Pattern Selector Dial
Raise the needle and turn the pattern selector dial
until the red indication is below the desired stitch.
At the same time the appropriate thread tension,
zigzag width and stitch length are indicated in the
upper portion of the guide message window.
Pattern selector dial
Red indicator mark
Thread tension dial
Zigzag width
Stitch length
Recommended presser foot
* Concerning items through above,
there sometimes is a discrepancy between
the settings shown on the front panel and
those shown on the reference chart inside
the top cover.
The reference chart settings are
recommended for the special sewing
techniques illustrated on the chart.
Zigzag Width Control
The higher the number, the wider the stitch width.
This machine will sew the maximum 6.5 mm (0.25Ó)
wide zigzag.
* Raise the needle above the fabric when
you set the stitch width.
Stitch Length Control
The higher the number, the longer the stitch length.
You can select the suitable stitch length for fabrics
that you plan to sew.
Note:
Stitch length is automatically set for stretch stitch
patterns on pattern number 2.16 to 24.
Infinite Needle Position
When pattern number 1 is selected and the stitch
width control is activated, you can move the needle
between center and left needle positions.
01 3245
601234
012 3 4 56789
BH
12
RAA
3
A
0123456
01234
12340
01 32 456
01 32 456
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
17
01 32 456
12340
43
5
Straight Stitching
Stitch selector: 1
Stitch width:
Stitch length: 1.5Ð4
Top thread tension: 2Ð6
Presser foot: A: Zigzag foot
¥ Starting to Sew
Raise the presser foot and position the fabric next to
a seam guide line on the needle plate (see page 18).
Lower the needle to the point where you want to
start.
Lower the presser foot and pull the threads toward
the back. Depress the foot control.
Gently guide the fabric along the seam guide line
letting the fabric feed naturally.
¥ Changing Sewing Direction
Stop the machine and bring the needle down into the
fabric by pressing the up/down needle position but-
ton. Raise the presser foot.
Pivot the fabric around the needle to change sewing
direction as desired. Lower the presser foot.
Presser foot lifter
¥ Finishing Sewing
To fasten the ends of seams, press the reverse
button and sew several reverse stitches.
Raise the presser foot. Remove the fabric, draw the
threads to the back and cut using the thread cutter.
The threads are cut the proper length for starting the
next seam.
Thread cutter
Fabric
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide

AAASewing.com
18
Seam Allowance Lines
The seam guides on the needle plate and hook
cover plate help you measure seam width.
* The number indicates the distance between
the middle needle position and the seam
allowance line.
Sewing on Heavy Fabrics
Pressing the black button on Foot A (before lowering)
locks it in a horizontal position.
This ensures even feeding at the beginning of seams
and helps when sewing many layers of fabric.
When you reach a point of increased thickness, lower
the needle and raise the foot. Press in the black
button, then lower the foot and continue sewing.
It releases automatically after a few stitches.
Fabric
A: Zigzag foot
Millimeters Inches
Marks on
needle plate 15 20 4/8Ó 5/8Ó 6/8Ó
Middle needle position
Edge of fabric
Needle plate guide lines
Turn a Square Corner
To turn a square corner 1.6 cm (5/8Ó) from the fabric
edge.
1. Stop stitching and lower the needle by
pressing the up/down needle position button
when the fabric edge lines up with the
cornering guide, as shown.
2. Raise the presser foot and turn the fabric to
line the edge with the 1.6 cm (5/8Ó) seam
guide.
3. Lower the presser foot and begin stitching in
the new direction.
Cornering guide
Up/down needle position button
Presser foot lifter
15
20
5/8
6/8
Janome 5024 Instruction Manual
www.aaasewing.com
5024 Owners Manual/ User Guide