JAROLIFT TDRR-01W User manual
Operating manual
Rev.: 05/2015_Jarolift TDRR 01W_ST
1-channel radio receiver - wall-mounted unit
Type TDRR-01W
compliant
2011/65/EU
RoHS
General safety instructions ...........................................1
Technical data & included with delivery..................2
Electrical connection.......................................................2
Assembly .............................................................................3
Programming the radio code.......................................4
Contact information........................................................6
GB
F
I
E
NL
PL
TR
An English manual can be downloaded at http://www.jarolift.de/en/manuals
Vous trouverez des instructions en français sur http://www.jarolift.de/fr/instructions
Una guida in italiano è disponibile alla pagina http://www.jarolift.de/it/guida
Encontrará un manual en idioma español en http://www.jarolift.de/es/manual
Een handleiding in Nederlands kan u vinden op http://www.jarolift.de/ne/handleiding
Instrukcja w jezyku polskim znajduje sie na stronie http://www.jarolift.de/pl/instrukcje
Türkçe kılavuzu http://www.jarolift.de/tr/kilavuzu adresinde bulabilirsiniz
Michael Mayer
Managing Director
The radio receiver TDRR 01W meets the requirements of the relevant European and national regulations.
2014/53/EU - Radio Equipment regulations
2014/30/EU - EMC regulations
2014/35/EU - Low voltage regulations
EN 301 489-1 V1.9.2:2011; EN 301 489-3 V1.6.1:2013;
EN 300 220-2 V2.4.1:2012; EN 60669-1:1999/A2:2008;
EN 60669-2-1:2004/A12:2010;
Schoenberger Germany Enterprises GmbH & Co. KG
Zechstraße 1-7
82069 Hohenschäftlarn - Germany
WEEE-Reg.-Nr. DE 41060608 for: JAROLIFT®TM
is a registered brand of Schoenberger Germany Enterprises GmbH & Co.KG, Zechstraße 1-7, 82069 Hohenschäftlarn, Germany
1General safety instructions
1
Failure to follow these instructions can endanger life!
Connecting the tubular motor to the mains, and any work on
electrical equipment, must only be carried out by an appro-
ved electrical specialist in accordance with the connection
plans included in these instructions (see Page 3).
Always disconnect the power prior to installing or connecting
any electrical equipment.
Any work on electrical equipment carries the risk of fatal injury
from electric shock.
Observe the regulations regarding installation in damp areas.
In particular, observe DIN VDE 0100, section 701 and 702 when
using in damp areas. These regulations contain compulsory protec-
tive measures.
Use of defective equipment can cause a hazard for persons and
material damage (electric shock, short circuit)
Never use defective or damaged units.
Check the motor and mains cable for any damage.
Please refer to our Service Team (see last page), if you nd any
damage to the equipment.
Please instruct all personnel on how to use the radio receiver
safely.
Improper use may lead to an increased risk of injury.
Observe the moving roller shutters and keep all personnel
clear until the shutter’s movement is completed.
Do not allow children to play with xed controls or the remo-
te control.
Keep the hand transmitter in such a way to prevent any acci-
dental operation, e.g. by children playing.
When cleaning the roller shutters, make sure to disconnect
the power.
IMPORTANT
In accordance with DIN EN 13695, care must be taken to ensure
that the movement conditions established for roller shutters as
per EN12045 are observed, therefore with side locking.
Shutter curtain slats with locking mechanisms are available at
www.jalousiescout.de.
Correct use / operating conditions
Use the radio receiver only to open and close roller shutters
and awnings.
The motor cable must be laid in an empty conduit as far as the
junction box, in accordance with local electrical regulations.
Only use the manufacturer’s original components and acces-
sories.
Conditions for use
For electrical connection, the installation site must have a
constant 230 V / 50 Hz electricity supply, with a main circuit
disconnect device (fuse) on site.
IMPORTANT
Important installation instructions
IMPORTANT
Before assembly, compare the voltage / frequency information on the type label with that of the local electricity network.
Before installing the radio receiver, remove or decommission any cables or units not needed for operation.
After unpacking, compare the following:
contents of package and the delivery information in these instructions.
the type of motor and the corresponding information on the type label.
Technical data & included with delivery 2
2
Technical data & included with delivery
Technical data
230 V, 50 Hz
< 400 W
1 Watt
IP 20
-0°C to + 60°C
Rolling code
433.92 MHz
The receiver can store a maximum of 15 transmitting channels
4 minutes
Compatible with all TDR radio transmitters, as of production date 03/2010
After you have unpacked the device, check the package content
with the information on the delivery contents in these instructions:
1. Outer frame, white
2. Receiver module incl. supporting frame, white
+ Instructions
Electrical connection
L1 N N
PE
N
L1
MOnly authorised electricians are permit-
ted to work on the power connections
of the wireless timer and all other elec-
trical work. All work must comply with
the wiring diagrams provided in these
instructions
Caution:
Any work on electrical equipment car-
ries the risk of fatal injury from electric
shock.
Always disconnect the power prior to
installing or connecting any electrical
equipment.
green / yellow
brown
black
Motor
blue
Power supply:
System load:
Standby consumption:
Protection:
max. authorised ambient temperature:
Radio coding:
Radio frequency:
Channels:
Power-on time:
Compatibility:
3
3Assembly
Assembly
1. First push the power supply unit out of the inner supporting frame
and the outer frame. To do this, hold the outer frame rmly on the
side and push the power supply unit from behind.
2. First, x the support frame into a suitable ush-mounted socket.
3. Now install the connections in accordance with the connection plan
shown on page 2 of these instructions.
When making the connection, the power supply unit must be loca-
ted on the outer frame before connection!
4. Once the electrical installation is completed, press the clock module
including the outer frame into the previously installed support fra-
me.
Function overview
Using the radio receiver button TDRR-01W, you can convert a simple tubular motor into an easy to use wireless motor in no time at all. The
motor can then be controlled remotely using any of the TDR remote transmitters available. Furthermore, the remote button oers a local operating option
via the three large buttons on the front (UP/STOP/DOWN).
The red LED indicator light on the front panel of the device signals the
following conditions:
permanently on (the unit is ready for operation)
(permanently on = orientation aid e.g. in darkness)
ashing (an activation command is being processed)
light is o (the device is in learning mode)
Please note!
If the end point of the tubular motor has been reached, the LED continues ashing for approximately 4 minutes as the receiver is still in self-holding
mode. Subsequently, the receiver will switch automatically to the “Ready” mode.
LED control light
UP
STOP
DOWN
Programming the radio code 4
4
Programming the radio code
1. Connect the radio receiver in accordance with the assembly instructions (see Page 3). Press the STOP button of the radio receiver for 3 se-
conds in order to activate the programming mode. The connected motor will vibrate briey, and the LED indicator light goes out.
This indicates that the receiver is now in programming mode for 5 seconds
2. Within 5 seconds, press the UP and DOWN button on your hand-held transmitter simultaneously and then press the STOP button briey.
If the code has been programmed successfully, the motor vibrates once more. Now you can control the motor using the UP/STOP/DOWN
buttons on your transmitter.
(Motor vibrates)
Press the UP / DOWN buttons
at the same time
then press the STOP
button
(Motor vibrates)
Press the STOP button
for 3 seconds
Copying an existing radio code (only when a transmitter has already been programmed)
1. Press the UP and DOWN buttons simultaneously on the transmitter you have already programmed. Then press the STOP button 8 times on
this transmitter. The motor will vibrate briey as conrmation.
2. Within 5 seconds, simultaneously press the UP and DOWN button on the transmitter onto which the code should be copied and then press
the STOP button briey. The motor will vibrate briey again as conrmation. The code has been copied to the new transmitter.
Press the UP / DOWN but-
tons at the same time
then press the STOP
button 8x
Transmitter 1
(Motor vibrates)
Press the UP / DOWN but-
tons at the same time
then press the
STOP button
Transmitter 2
(Motor vibrates)
Each button on the hand-held transmitter must be pressed for approx. 1 second!
Deleting the radio code (only when a transmitter has been programmed)
1. Press the UP and DOWN buttons on the transmitter at the same time. Then press the STOP button six times.
2. Now press the UP button inside 5 seconds. The motor will conrm the code has been deleted by vibrating briey.
Press the UP / DOWN but-
tons at the same time
then press the STOP
button 6x
Press the UP button
(Motor vibrates)
5
5Programming the radio code
Changing the direction of rotation of the motor
1. Press the UP and DOWN buttons on the programmed transmitter at the same time. Then press the STOP button four times.
2. Now press the UP button briey inside 5 seconds. The motor will conrm the direction has been changed by vibrating briey.
Press the UP / DOWN but-
tons at the same time
then press the STOP
button 4x
Press the UP button
(Motor vibrates)
Setting inching mode
1. Stop the motor using the STOP button.
Activating inching mode
2. Press the UP and DOWN buttons on the transmitter at the same time and then press the STOP button six times.
3. Now press the DOWN button within 5 seconds. A brief vibration of the motor conrms that the inching mode is activated.
Press the UP / DOWN but-
tons at the same time
then press the STOP
button 6x
Press the DOWN
button
(Motor vibrates)
The motor will now operate as long as you press the UP or DOWN button. In inching mode, press the UP or DOWN button for 3 seconds. The
motor moves to the end point or until you press the STOP button.
Please note, timer control will not function while inching mode is set!
1. Stop the motor using the STOP button.
De-activating inching mode
2. Press the UP and DOWN buttons on the transmitter at the same time and then press the STOP button six times.
3. Now press the DOWN button within 5 seconds. A brief vibration of the motor conrms that the inching mode is deactivated.
Press the UP / DOWN but-
tons at the same time
then press the STOP
button 6x
Press the DOWN
button
(Motor vibrates)
If you experience problems with one of our products, or you have received a defective unit, please contact the following
address in writing or by email:
is a registered brand of
Schoenberger Germany Enterprises GmbH & Co.KG
Zechstraße 1-7
82069 Hohenschäftlarn - Germany
Tel.: 08178 / 932 932
Fax.: 08178 / 932 970 20
www.jarolift.de
We reserve the right to make technical changes, and accept no liability for printing
errors and other errors.
Contact information 6
6
is a registered brand of Schoenberger Germany Enterprises GmbH & Co.KG, Zechstraße 1-7, 82069 Hohenschäftlarn, Germany
Other manuals for TDRR-01W
1
Table of contents
