Jatontec JTLink 5000 User manual

JATONTEC JTLink 5000
LTE-U CAT6 Small Cell
Installation Manual V1.0

PLEASE READ THESE SAFETY PRECAUTIONS!
RF Energy Health Hazard
The radio equipment described in this guide uses radio frequency transmitters.
Although the power level is low, the concentrated energy from a directional
antenna may pose a health hazard.
Do not allow people to come in close proximity to the front of the antenna while the
transmitter is operating.
Protection from Lightning
Before connecting this instrument to the power line, make sure that the voltage of
the power source matches the requirements of the instrument. The unit must be
standards.
Disposal and Recycling Information
Pursuant to the WEEE EU Directive electronic and electrical waste must not be
disposed of with unsorted waste. Please contact your local recycling authority for
disposal of this product.
Reduction of Hazardous Substances
This Device is compliant with the EU Registration, Evaluation, Authorization and
Restriction of Chemicals (REACH) Regulation and the EU Restriction of Hazardous
Substances (RoHS) Directive (Directive 2011/65/EU of the European Parliament and
of the Council).

Table of Contents
1. OVERVIEW................................................................................................................................................4
USER INTERFACE SPECIFICATION .....................................................................................................4
2. GETTING STARTED................................................................................................................................5
DEVICE LOGIC CONNECTION .............................................................................................................5
INSTALLING MOUNTING BRACKETS...................................................................................................6
HEADER CONNECTION.......................................................................................................................7
3. LED DISPLAY ...........................................................................................................................................8
4. GROUNDING............................................................................................................................................9

1. Overview
JTLink 5000 is a highly integrated CAT6 small cell base station with all-in-one packaging of
RF and base-band components. it includes integrated Quad receiver and transmitter to
support two channel MIMO and Carrier Aggregation. It is available as an all outdoor solution
for LTE-U applications to minimize physical footprint and operator expense.
User Interface Specification
Model
Description & User Interface
JTLink 5000
- Panel antenna:
B46 (2 X 2) 17dBi, (4X 4) 13dBi
B42/43/48 13dBi
- 2 RJ45 10/100/1000M LAN Port
- 1 SFP Port
- Power, SYN, SAS, LTE, Link, ALM
- 48V/0.5A PoE adapter/ 48V DC, ODU Power <24Watts
- Dimensions: 250 mm (L) × 250 mm (W) × 80mm (D)
- Weight: <2.5 Kg

2. Getting Started
1) Packing list
Upon receiving the product, please unpack the product package carefully. Each product is
shipped with the following items:
Table 2-1 Packing List
Outdoor CPE Products
Quantity
Small cell
1
PoE adapter
1
Power cord
1
Mounting brackets
1
PC Ethernet Cable
1
If you find any of the items is missing, please contact our local distributor immediately.
2) Unpacking the Equipment
Table 2-1 lists all the standard parts that are supplied in your LTE small cell Installation
Package. Please take the time to unpack the package and check its contents against this list.
3) Installing the Equipment
Device Logic connection
For small cell product, it is suggested that the device be installed in a shaded area to avoid
direct sun light exposure which may cause over heat in certain extreme weather condition.
To power on the device, the small cell must use a 48V PoE integrated DC power supply
adapter. The power adapters can operate in 100-240V AC range and therefore can be used
in different country. Once the device is powered up, the user should wait for about 2 minutes
before the device becomes operational.
To connect PC, LAN switch or other type of IP device to the small cell product, the user
should use SFTP CAT5E Ethernet cable/ Optical cables and connect to the appropriate PoE
adapter LAN port/ device SFP port. Once connected, the ETH LED indicator should come on.

Installing Mounting brackets

Header Connection

3. LED Display
LED
Function
Description
PWR
Power indicator
Solid Blue –Device is power on.
SYN
GPS status indicator
Solid Blue –GPS syncing.
Blinking Blue –GPS synced successfully
Off –Device GPS is not working
SAS
TBD
TBD
LTE
Cell status indicator
Solid Blue –The cell setup success.
Blinking Blue –The cell is communicating.
Off –The cell is not working.
LNK
LAN port status
Solid Blue –S1 connected.
Blinking Blue –S1 connecting.
ALM
Alarm indicator
Solid Blue –Device alarm.

4. Grounding
Make sure that the installation of the small cell unit, antenna and cables is performed in
accordance with all relevant national and local building and safety codes. Even where
grounding is not mandatory according to applicable regulation and national codes, it is
highly recommended to ensure that the outdoor unit and the antenna mast are grounded and
suitable lightning protection devices are used so as to provide protection against voltage
surges and static charges. In any event, we not liable for any injury, damage or regulation
violations associated with or caused by installation, grounding or lightning protection.
The Grounding screw is located on the lower part at the back of the unit (see Figure below).
Use 10 AWG cable for grounding.
Connect one of a grounding cable to the grounding screw and firmly tighten the grounding
screw. Connect the opposite end of the grounding cable to a good ground(earth) connection.