Jaypro PVB Series User manual

JAYPRO PVB SERIES COLLEGIATE NET SYSTEM
Installation and Operating Instructions
Applicable Part Numbers/Models:
PVB-1500: Steel Collegiate Net System
PVB-4500/PVB-5000: Featherlite Collegiate Net system

PVB Series Collegiate Net System Instructions
- 1 of 9-
JSL-Inst040
www.jayprosports.com
Table of Contents
1Safety................................................................................................................ 2
2Specifications .................................................................................................. 2
3Introduction ..................................................................................................... 2
4Required Tools ................................................................................................. 3
5Included Hardware & Components............................................................ 4
5.1 System Components.............................................................................. 4
5.2 Hardware................................................................................................. 5
6Assembly .......................................................................................................... 6
7Maintenance .................................................................................................. 9

PVB Series Collegiate Net System Instructions
1Safety
•WARNING: Do not attempt to remove the height adjuster pin if the net is under
tension.
•WARNING: Always use protective padding around each upright during use.
•WARNING: Uprights are heavy. Do not attempt to lift or install without assistance.
•IMPORTANT: Follow all warning labels on equipment.
•IMPORTANT: Inspect for damage before and after each use.
2Specifications
UPRIGHT
OUTER
DIAMETER HEIGHT RANGE
#OF
POSITIONS WEIGHT
UPPER
UPRIGHT
MATERIAL
LOWER
UPRIGHT
MATERIAL
PVB-1500 3-1/2”
(89mm)
6’6” to 8’2”
(2.0m to 2.5m)
16
Pin Stops
152 lbs
(69kg)
Aluminum
6063 Steel
PVB-4500
(3” FLOOR
SLEEVE)
3-1/2”
(89mm)
6’6” to 8’2”
(2.0m to 2.5m)
16
Pin Stops
104 lbs
(47kg)
Aluminum
6063
Aluminum
6063
PVB-5000 3-1/2”
(89mm
6’6” to 8’2”
(2.0m to 2.5m)
16
Pin Stops
104 lbs
(47kg)
Aluminum
6063
Aluminum
6063
3Introduction
Note: The Flex Net supplied with this system will stretch slightly during the first few uses.
This is a natural consequence of the headband fibers being stretched under tension.
During this break-in period, the headband and net body may sag during use. Simply
increase tension to remove the sag.
These instructions assume that the appropriate ground sleeves have been correctly
installed:
1NCAA and NFHS rules require that the upright standards must be installed at least 3’3”
(1m) outside the court boundaries. Jaypro recommends 36’ spacing on center to satisfy
both regulations.

PVB Series Collegiate Net System Instructions
Figure 3-1: Correct Ground Sleeve Dimensions
4Required Tools
Before continuing, please verify that you have the following tools required to complete
the installation and setup of your PVB Series Collegiate Net System.
Adjustable wrench
Hex keys – 3/16”, 5/16”

PVB Series Collegiate Net System Instructions
5Included Hardware & Components
Before continuing, please open all packages to verify that you have all the required
hardware for installation and setup. If any of the following items are missing, contact the
Jaypro Sports customer support team, Monday through Friday, 8:30AM to 5:00 PM (EST),
at 1-800-243-0533.
5.1 System Components
Figure 5-1: PVB-1500 Standard Upright (PVB150B, 2X), included w/ PVB-1500 system only.
Figure 5-2: PVB-5000 Standard Upright (PVB501B, 2X), included w/ PVB-5000 system only.
Figure 5-3 PVB-4500 Standard Upright (PVB450B, 2X), included w/ PVB-4500 system only.
Figure 5-4: Winch with strap (PVBWINCH, 1X).

PVB Series Collegiate Net System Instructions
Figure 5-5: Flex-Net (PVBN-6, 1X)
Figure 5-6: Antennae and Net Tapes (VBA-4, 1 pair)
Figure 5-7: Anchor Strap (PVB-604, 1X)
5.2 Hardware
Figure 5-8: Button Head Cap Screw (HS5098, 1X) Figure 5-9: Button-Head Cap Screw (HS5201, 1X)
Figure 5-10: Acorn Nut (HN809, 2X) Figure 5-3: Spacer Bearing (HM6347, 1X)

PVB Series Collegiate Net System Instructions
6Assembly
WARNING: Uprights are heavy. Do not attempt to lift or install without assistance.
1. Install each upright into the ground sleeves.
2. Follow instructions included with winch to set the winch clamp to the correct
upright diameter (3-1/2”).
3. Install winch to one upright using the button head cap screw and acorn nut
(Figure 6-1, items 1 & 2).
4. Fasten the clamp together using the cap screws supplied with the winch (Figure
6-1, item 4-1).
Figure 6-1: Winch installation.

PVB S
e
5
6
e
ries Collegiate
.Install the
.Set the h
e
WARNING:
Net System Ins
anchor stra
e
ight of the
u
Do not atte
m
tructions
-
p to the up
r
Figure 6
-
u
prights usin
m
pt to remov
e
Figure
6
-
7 of 9-
JSL-Inst040
r
ight without
-
2: Install anchor str
a
g the install
e
e
the hei
g
ht a
d
6
-3: Set upright hei
gh
the winch (
a
p.
e
d height a
d
dj
uster pin if t
h
h
t.
Figure 6-2).
d
just pin (Fig
h
e net is und
e
ure 6-3).
e
r tension.

PVB S
e
7
8
9
1
0
1
2
NC
A
hea
d
e
ries Collegiate
.Attach o
n
(Figure 6-
4
.Adjust th
e
***The ne
t
in before
.Tension t
h
necessar
y
0
.Verify ne
t
downwa
r
center th
e
adjust pi
n
1. Attach th
straps ar
o
A
A and NFH
S
d
band whe
n
Net System Ins
n
e end of n
e
4
).
e
length of t
h
t
will stretch
applying te
n
h
e net by tu
r
y
to keep n
e
heights an
d
r
d due to ne
e
net. WAR
N
n
.
e bottom n
e
o
und buckle
s
S
rules stipul
a
n
fully tensio
n
tructions
-
e
t to anchor
Figure 6-
h
e anchor s
t
~6 – 8 inch
e
n
sion when
c
r
ning the wi
n
e
t centered.
d
net center
i
t tension; y
o
N
ING: Relea
s
e
t straps to
e
s
for additio
n
a
te that the
r
n
ed.
-
8 of 9-
JSL-Inst040
strap, then
4: Attach net to stra
p
t
rap as nec
e
e
s when ten
s
c
entering th
e
n
ch handle
c
i
ng. The up
r
o
u may nee
d
s
e tension fr
o
e
ach uprigh
t
n
al player s
a
r
e be no m
o
attach oth
e
p
s.
e
ssary to ce
n
s
ion is appli
e
e
net.
c
lockwise
2
.
A
r
ights will de
f
d
to adjust t
h
o
m the net
b
t
as shown i
n
a
fety.
o
re than ¾”
o
e
r end to win
n
ter net on
c
e
d so you m
u
A
djust anch
o
f
lect inward
h
eir heights
a
b
efore remo
v
n
Figure 6-5.
o
f sag in the
ch strap
c
ourt.
u
st factor thi
o
r strap as
and
a
nd/or re-
v
ing height
Wrap Velcr
net
s
o

PVB S
e
1
2
1
3
7
Your
reco
m
of ex
c
e
ries Collegiate
2
.Attach n
e
antenna
e
3
.Install pa
d
Maintena
PVB Series
C
m
mended t
h
c
essive we
a
Strap
Net
Sprin
g
Winc
h
Scre
w
Net System Ins
e
t antenna
e
e
set.
d
s around e
a
nce
C
ollegiate N
e
h
at the co
m
a
r. Key area
s
webbing
g
clips and
D
h
mechanis
m
w
s and nuts
tructions
-
Figure 6-5: Secur
e
e
and tapes
a
a
ch upright.
e
t System is
d
m
ponents be
s
to inspect
i
D
-rings
m
-
9 of 9-
e
bottom net straps
t
a
ccording t
o
d
esigned to
inspected
a
i
nclude (bu
t
t
o upri
g
hts.
o
instruction
provide ye
a
a
t least onc
e
t
are not limi
s included
w
a
rs of play; h
e
every seas
ted to):
w
ith
owever, it is
on, for signs