jcb LT26 Installation manual

Important! It is essential that you read the instructions in this manual before assembling,
maintaining and operating this machine.
Subject to technical modifications.
Keep the instruction for future reference.
SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
SAFETYAND OPERATING MANUAL
ORIGINAL INSTRUCTIONS
26CC LINE TRIMMER
JCB-LT26
JCB-LT26_960443001-01_Manual_final.indd 1JCB-LT26_960443001-01_Manual_final.indd 1 12/2/2010 4:20:11 PM12/2/2010 4:20:11 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
GENERAL SAFETY RULES
INTENDED USE
The product should only be used outdoors.
The product is intended for cutting long grass, weeds, and similar vegetation at or
about ground level. The cutting plane should be approximately parallel to the ground
surface. The product should not be used to cut or trim hedges, bushes or other
vegetation where the cutting plane is not parallel to the ground surface.
For safe operation, read and understand all instructions before using the trimmer.
Follow all safety instructions. Failure to follow all safety instructions listed below can
result in serious personal injury.
Do not allow children or untrained individuals to use this unit.
Never start or run the engine in a closed or poorly ventilated area; breathing
exhaust fumes can kill.
Clear the work area before each use. Remove all objects such as rocks, broken
glass, nails, wire or string which can be thrown or become entangled in the fixed
line head.
Wear full eye and hearing protection while operating this unit.
Wear heavy long trousers, boots, and gloves. Do not wear loose fitting clothing,
short trousers, jewellery of any kind or use with bare feet.
Secure long hair so it is above shoulder level to prevent entanglement in any
moving parts.
Keep all bystanders, children and pets at least 15 m away.
Do not operate this unit when you are tired, ill or under the influence of alcohol,
drugs or medication.
Do not operate in poor lighting.
Keep firm footing and balance. Do not overreach. Overreaching can result in loss
of balance or exposure to hot surfaces.
Keep all parts of your body away from any moving part.
Do not touch area around the silencer and engine of the trimmer, these parts get
hot from operation.
Always stop the engine and remove the spark plug wire before making any
adjustments or repairs except for carburetor adjustments.
Inspect the unit before each use for loose fasteners, fuel leaks, etc. Replace any
damaged parts before use.
The fixed line head will rotate during carburetor adjustments.
JCB-LT26_960443001-01_Manual_final.indd 2JCB-LT26_960443001-01_Manual_final.indd 2 12/2/2010 4:20:18 PM12/2/2010 4:20:18 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
It has been reported that vibrations from hand-held tools may contribute to a
condition called Raynaud’s Syndrome in certain individuals. Symptoms may include
tingling, numbness and blanching of the fingers, usually apparent upon exposure to
cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work
practices are all thought to contribute to the development of these symptoms. It is
presently unknown what, if any, vibrations or extent of exposure may contribute to
the condition. There are measures that can be taken by the operator to possibly
reduce the effects of vibration:
Keep your body warm in cold weather. When operating the unit, wear gloves to
keep the hands and wrists warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
After each period of operation, exercise to increase blood circulation.
Take frequent work breaks. Limit the amount of exposure per day.
If you experience any of the symptoms of this condition, immediately discontinue use
and see your doctor about these symptoms.
Keep the tool well maintained, fasteners tightened and worn parts replaced.
Mix and store fuel in a container approved for fuel.
Mix fuel outdoors where there are no sparks or flames. Wipe up any fuel spillage.
Move 9m away from refueling site before starting engine.
Stop the engine and allow to cool before refueling, performing adjustments or
maintenance or storing the unit.
Allow the engine to cool; empty the fuel tank and secure the unit from moving before
transporting in a vehicle.
JCB-LT26_960443001-01_Manual_final.indd 3JCB-LT26_960443001-01_Manual_final.indd 3 12/2/2010 4:20:18 PM12/2/2010 4:20:18 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
ADDITIONAL SAFETY RULES FOR YOUR TRIMMER
Do not touch area around the silencer and engine of the trimmer, these parts get
hot from operation.
Stop the engine and allow to cool before refueling, performing adjustments or
maintenance or storing the unit.
Allow the engine to cool; empty the fuel tank and secure the unit from moving
before transporting in a vehicle.
Replace fixed line head if cracked, chipped, or damaged in anyway. Be sure the
fixed line head is properly installed and securely fastened. Failure to do so can
cause serious injury.
Make sure all guards, straps, deflectors and handles are properly and securely
attached.
Use only the manufacturer's replacement line in the cutting head. Do not use any
other cutting attachment.
Never operate unit without the safety guard in place and in good condition.
Maintain a firm grip on both handles while trimming. Keep fixed line head below
waist level. Never cut with the fixed line head located over 76 cm or more above
the ground.
JCB-LT26_960443001-01_Manual_final.indd 4JCB-LT26_960443001-01_Manual_final.indd 4 12/2/2010 4:20:18 PM12/2/2010 4:20:18 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
SYMBOLS
Thank you for your purchase.
Thetrimmerhasbeenengineeredandmanufacturedtoahighstandardfordependability,
ease of operation, and operator safety. If properly cared for, it will give years of rugged,
trouble-free performance.
Important: Some of the following symbols may be used on the tool. Please learn
the meaning. Proper interpretation of the symbols will allow better and safer opera-
tion of the tool.
Indicates danger, warning or caution. It means “Attention! Your safety is
involved.”
Read the operation manual and follow all warnings and safety
instructions.
Wear eye and ear and head protection.
Keep all bystanders, especially children and pets, at least 15 m from the
operating area.
Danger of ricochet.
Do not install blade on this unit.
Rotational direction and maximum speed of the shaft for the cutting
attachment.
Wear non-slip safety footwear.
Wear non-slip heavy-duty gloves.
Do not smoke when mixing fuel or filling fuel tank.
Use unleaded petrol intended for motor vehicle use with an octane rating
of 91 ([R+M]/2) or higher.
Use synthetic 2-stroke oil for air cooled engines.
JCB-LT26_960443001-01_Manual_final.indd 5JCB-LT26_960443001-01_Manual_final.indd 5 12/2/2010 4:20:18 PM12/2/2010 4:20:18 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
Mix the fuel mixture thoroughly each time before fueling or refueling.
On/Off Switch (I = on; O = off)
Conforms with all regulatory standards in the EU country where the
product is purchased.
JCB-LT26_960443001-01_Manual_final.indd 6JCB-LT26_960443001-01_Manual_final.indd 6 12/2/2010 4:20:18 PM12/2/2010 4:20:18 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
TECHNICAL DATA
SPECIFICATIONS
Weight (kg)
Without fuel; without string head
Without fuel; with string head 4.66
4.82
Fuel tank volume [cm3or (L)] 250 or (0.25)
Cutting swath (mm) 432
Engine displacement (cm3/cc) 26
Line diameter (mm) 2.4
Maximum engine performance (in accordance with ISO
8893) (kW) 0.65
Maximum rotational frequency of spindle (min-1) 12,000
Engine speed (rotational frequency) at recommended
maximum spindle (min-1)12,000
Engine speed (rotational frequency) at idle (min-1) 2,800-3,800
Fuelconsumption(inaccordancewithISO8893)atmaximum
engine performance [kg/h or (L/h)] 0.33 or (0.45)
Specific fuel consumption (in accordance with ISO 8893) at
maximum engine performance [g/kW.h or (L/kW.h)] 508 or (0.7)
NOISE INFORMATION (Uncertainty of noise is K=3dB.)
Sound pressure level at operator position (in accordance
with EN ISO 22868) [LpA dB(A)] 97.7
Measured sound power level dB(A) 108.4
Sound power level (in accordance with EN ISO 22868) [LwA
dB(A)] 110
VIBRATION INFORMATION (Uncertainty of vibration is K=1.5 m/s2.)
Vibration level idling (m/s2)
Left handle
Right handle 8.8
4.9
Vibration level racing (m/s2)
Left handle
Right handle 15.4
10.4
JCB-LT26_960443001-01_Manual_final.indd 7JCB-LT26_960443001-01_Manual_final.indd 7 12/2/2010 4:20:19 PM12/2/2010 4:20:19 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
COMPONENT LIST AND ASSEMBLY
ASSEMBLY
See Figure 2.
WARNING
Ifanyparts aredamaged ormissing,do notoperate thetooluntil theparts are replaced.
Failure to heed this warning could result in serious personal injury.
WARNING
Do not attempt to modify the product or create accessories not recommended for use
with the product. Any such alteration or modification is misuse and could result in
hazardous condition leading to possible serious personal injury.
WARNING
To prevent accidental starting that could cause serious personal injury, always
disconnect the engine spark plug wire from the spark plug when assembling parts.
WARNING
Never attach or adjust any attachment while the power head is running. Failure to stop
the engine may cause serious personal injury.
WARNING
Be certain the knob is fully tightened before operating the equipment; during use,
check periodically for tightness to avoid serious injury.
1. Primer bulb
2. Choke lever
3. Fuel cap
4. Starter grip
5. On/Off switch
6. Throttle trigger
7. Rear handle
8. Front handle
9. Shaft
10.Safety guard
11.Fixed line head
12.Cutting line
13.Knob
14.Throttle lock
15.Idle speed screw
16.Spool retainer
COMPONENT LIST
See Figure 1.
JCB-LT26_960443001-01_Manual_final.indd 8JCB-LT26_960443001-01_Manual_final.indd 8 12/2/2010 4:20:19 PM12/2/2010 4:20:19 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
OPERATING INSTRUCTIONS
WARNING
To reduce the risk of injury, the user must read and understand the manual.
WARNING
Do not attempt to operate the trimmer until you have read thoroughly and completely
understood all instructions, safety rules etc contained in the manual. Failure to
comply may result in accidents involving fire, electric shock or serious personal
injury. Save the manual and review frequently for continuing safe operation, and for
instructing others who may use the tool.
Read all instructions.
FUELING AND REFUELING
Fuel is highly flammable. Always handle with care.
Always refuel outdoors where there are no sparks and flames. Do not inhale fuel
vapors.
Do not let petrol or oil come in contact with your skin.
Keep petrol and oil away from your eyes. If petrol or oil comes in contact with your
eyes, wash them immediately with clean water. If irritation still exists, see a doctor
immediately.
Clean up spilled petrol immediately.
TO MIX THE FUEL
See Figure 3.
The product is powered by a 2-stroke engine and requires pre-mixing petrol with
2-stroke oil. Pre-mix unleaded petrol and 2-stroke engine oil in a clean container
approved for petrol.
The engine is certified to operate on unleaded petrol intended for automotive use
with an octane rating of 91 ([R+M]/2) or higher.
Do not use any type of pre-mixed petrol/oil from fuel service stations, such as
the pre-mixed petrol/oil intended for use in mopeds, motorcycles, etc. Do not use
automotive oil or 2-stroke outboard oil.
Use only synthetic 2-stroke oil.
Mix 2% of synthetic 2-stroke oil into the petrol. This is a 50:1 ratio.
JCB-LT26_960443001-01_Manual_final.indd 9JCB-LT26_960443001-01_Manual_final.indd 9 12/2/2010 4:20:19 PM12/2/2010 4:20:19 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
1 l + 20 ml =
2 l + 40 ml =
3 l + 60 ml = 50:1 (2%)
4 l + 80 ml =
5 l + 100 ml =
Mix the fuel thoroughly each time before fueling.
Mix in small quantities. Do not mix quantities more than the amount to use in a
30-day period. Synthetic 2-stroke oil containing a fuel stabilizer is recommended.
TO FILL THE TANK
1. Clean surface around the fuel cap to prevent contamination.
2. Loosen the fuel cap slowly to release pressure and to keep the fuel from spilling
around the cap.
3. Carefully pour the fuel mixture into the tank. Do not spill.
4. Prior to replacing the fuel cap, clean and inspect the gasket.
5. Immediately replace and tighten the fuel cap. Wipe up any fuel spillage. Move 9 m
away from the refueling site before starting the engine.
Note: It is normal for smoke to emit from a new engine during and after first use.
WARNING
Always shut off the engine before fueling. Never add fuel to a machine with a running
or hot engine. Move at least 9 m from the refueling site before starting the engine.
Do not smoke!
JCB-LT26_960443001-01_Manual_final.indd 10JCB-LT26_960443001-01_Manual_final.indd 10 12/2/2010 4:20:19 PM12/2/2010 4:20:19 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
STARTING AND STOPPING ENGINE
See Figure 4.
WARNING
Never start or run the engine inside a closed or poorly ventilated area; breathing
exhaust fumes can kill.
Note: Before starting the unit, make sure:
the On/Off switch is in “I” position;
the trimmer is lying on a flat and bare surface.
TO START A COLD ENGINE
1. Press the primer bulb slowly 10 times.
Note: After the 7th press, the fuel should be visible in the primer bulb. If not, con-
tinue pressing until the fuel is visible.
2. Set the choke lever to “Full” choke position.
3. Squeeze the throttle trigger completely and pull the starter grip until the engine
starts. Do not pull the starter grip more than 4 times.
Note: Keep the throttle trigger squeezed completely.
4. Set the choke lever to “Half” choke position.
5. Pull the starter grip until the engine starts. Do not pull the starter grip more than 6
times.
6. Allow the engine to run for 10 seconds, then set the choke lever to “Run” position.
Note: If the engine does not start, return to “Full” choke position and repeat the
process beginning at step 2.
TO START A WARM ENGINE
1. Press the primer bulb slowly 10 times.
2. Set the choke lever to “Run” position.
3. Squeeze the throttle trigger completely and pull the starter grip until the engine
starts.
TO STOP THE ENGINE
Press and hold the On/Off switch in “O” position until the engine stops.
JCB-LT26_960443001-01_Manual_final.indd 11JCB-LT26_960443001-01_Manual_final.indd 11 12/2/2010 4:20:19 PM12/2/2010 4:20:19 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
OPERATING THE TRIMMER
See Figure 5.
Hold the trimmer with the right hand on the rear handle and the left hand on the
front handle.
Keep a firm grip with both hands while in operation. The trimmer should be held at
a comfortable position with the rear handle at about hip height.
Always operate the trimmer at full throttle.
Cut tall grass from top down. This will prevent grass from wrapping around the shaft
housing and fixed line head which may cause damage from overheating.
If grass gets wrapped around the fixed line head, stop the engine, disconnect the
spark plug wire, and remove the grass.
Prolonged cutting at partial throttle will result in oil dripping from the silencer.
CUTTING TIPS
See Figure 6.
When cutting, make sure the cutter head is at a slightly slanted angle while still
keeping it parallel with the ground surface.
Move the head in steady strokes from right to left through the grass.
JCB-LT26_960443001-01_Manual_final.indd 12JCB-LT26_960443001-01_Manual_final.indd 12 12/2/2010 4:20:19 PM12/2/2010 4:20:19 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
MAINTENANCE
WARNING
Use only the original manufacturer's replacement parts, accessories and
attachments. Failure to do so can cause possible injury, poor performance and may
void your warranty.
You may make adjustments and repairs as described in the manual. For other
repairs, have the trimmer serviced by an authorised service agent.
Consequences of improper maintenance may include excessive carbon deposits
resulting in the loss of performance and discharge of black oily residue dripping
from the silencer.
Make sure all guards, straps, deflectors and handles are properly and securely
attached to avoid the risk of personal injury.
The cutting attachment must not rotate in idle mode. If this requirement is not
satisfied, the idle speed needs adjustment (See Figure 10) or the machine needs
urgent maintenance by a qualified technician.
LINE REPLACEMENT
See Figure 7.
Use 2.4 or 2.8 mm diameter monofilament line. For best performance, use the original
manufacturer's replacement line.
1. Stop the engine and disconnect the spark plug lead.
2. Pull and remove the old line from the holes located on top of the fixed line head.
3. Use 2 pieces of the provided pre-cut trimmer lines or cut 2 pieces of trimmer lines,
28 cm in length.
4. Insert the line into the slots located at both sides of the fixed line head. The line
should be pushed in until about 2.5 cm is left protruding from the holes of the fixed
line head.
Note: The fixed line head has no string line extending function. Do not tap the fixed
line head on the ground.
CLEANING THE EXHAUST PORT AND SILENCER
Depending on the type of fuel used, the type and amount of oil used, and/or your
operating conditions, the exhaust port and silencer may become blocked with
carbon deposits.
If you notice power loss with your petrol-powered tool, contact a qualified service
technician to remove these deposits and restore performance.
JCB-LT26_960443001-01_Manual_final.indd 13JCB-LT26_960443001-01_Manual_final.indd 13 12/2/2010 4:20:19 PM12/2/2010 4:20:19 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
SPARK ARRESTOR CLEANING OR REPLACEMENT
The spark arrestor must be cleaned or replaced every 25 hours or yearly to ensure
proper performance of the product.
Spark arrestors may be in different locations depending on the model purchased.
Please contact your nearest service dealer for the spark arrestor location of your
model.
CLEANING THE AIR FILTER SCREEN
See Figure 8.
For proper performance and longer life span, keep the air filter screen clean.
1. Remove the air filter cover by pushing down on the latch while gently pulling on
the cover.
2. Brush the air filter screen lightly.
3. Replace the air filter cover by inserting the tabs of the cover into the slots on the
air filter base; then push the cover up until it latches securely in place.
FUEL CAP REPLACEMENT
WARNING
A leaking fuel cap is a fire hazard and must be replaced immediately.
The fuel cap contains a non-serviceable filter and check valve.
A clogged fuel filter will cause poor engine performance.
If performance improves when the fuel cap is loosened, the check valve may be
faulty or the filter clogged. Replace the fuel cap if required.
SPARK PLUG REPLACEMENT
See Figure 9.
This engine uses a Champion RCJ-6Y or NGK BPMR7A spark plug with 0.05 in.
electrode gap. Use an exact model and replace annually.
IDLE SPEED ADJUSTMENT
See Figure 10.
If the cutting attachment turns at idle speed, the idle speed screw needs adjusting.
Turn the idle speed screw counterclockwise to reduce the idle rpm and stop the
cutting attachment movement.
If the cutting attachment still moves at idle speed, contact a service dealer and
JCB-LT26_960443001-01_Manual_final.indd 14JCB-LT26_960443001-01_Manual_final.indd 14 12/2/2010 4:20:20 PM12/2/2010 4:20:20 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
discontinue use until repair is made.
STORING THE PRODUCT
Clean all foreign materials from the product.
Store the unit indoors in a dry, well-ventilated area that is inaccessible to children.
Keep away from corrosive agents such as garden chemicals.
Abide by all ISO and local regulations for the safe storage and handling of petrol.
WHEN STORING FOR 1 MONTH OR LONGER
Drain all fuel from the tank into a container approved for petrol. Run the engine until
it stops.
JCB-LT26_960443001-01_Manual_final.indd 15JCB-LT26_960443001-01_Manual_final.indd 15 12/2/2010 4:20:20 PM12/2/2010 4:20:20 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
PROBLEM SOLVING
If these solutions do not solve the problem, contact your authorised service dealer.
PROBLEM POSSIBLE CAUSE SOLUTION
Engine will not start. Power switch is off. Make sure the On/Off switch is on
(“I” position).
No spark. The spark plug may be damaged.
Remove it and check for dirt or
cracks.
Replace with a new spark plug.
No fuel. Push primer bulb until the bulb is
full of fuel.
Ifthebulb does notfill,theprimary
fuel delivery system is blocked.
Contact a service dealer.
If the bulb fills, the engine may be
flooded. Proceed to the next item.
Fuel is old. Remove fuel from product.
Press primer bulb while draining
fuel.
Mix fresh petrol with 2-stroke oil,
fill fuel tank and follow the starting
procedure.
Starter grip harder to pull
than when new. Contact a service dealer.
JCB-LT26_960443001-01_Manual_final.indd 16JCB-LT26_960443001-01_Manual_final.indd 16 12/2/2010 4:20:20 PM12/2/2010 4:20:20 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
Engine will not start. Engine is flooded. Remove spark plug, then turn
the unit so the spark plug hole is
aimed at the ground.
Set the choke lever to “Run”
position and pull starter grip 10 to
15 times. This will clear excessive
fuel from the engine.
Remove any fuel from the
product.
Clean and reinstall the spark
plug.
Clean up any spilled fuel and
move at least 9 m away before
restarting.
Pull starter grip 3 times with the
choke lever at “Run” position.
If the engine does not start, set
the choke lever to “Full” choke
position and repeat the normal
starting procedure.
If the engine still fails to start,
repeat procedure with a new
spark plug.
Engine does not stop
when the On/Off
switch is off.
Electrical connection is
loose/unplugged. Setthe chokeleverto “Full”choke position to stop the engine.
Immediately stop using the
product.
Check that the electrical
connection at the bottom of the
trimmer is properly connected.
Contact a service dealer if the
problem persists.
Engine starts but will
not accelerate. Not enough time given for the engine to warm
up.
Allow the engine to completely
warm up.
If the engine does not accelerate
after 3 minutes, contact a service
dealer.
JCB-LT26_960443001-01_Manual_final.indd 17JCB-LT26_960443001-01_Manual_final.indd 17 12/2/2010 4:20:20 PM12/2/2010 4:20:20 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
Engine starts but
will only run at high
speed and at half
choke.
Carburetor requires
adjustment. Contact a service dealer.
Engine does not
reach full speed
and emits excessive
smoke.
Improper mixing of oil/
fuel. Use fresh fuel and the correct 2-stroke oil mix.
Air filter is dirty. Cleanthe air filter.Refer to “Cleaning
the Air Filter Screen” in the manual.
Spark arrestor screen is
dirty. Contact a service dealer.
Engine starts, runs
and accelerates, but
will not idle.
Idle speed screw on
carburetor requires
adjustment.
Turn idle speed screw clockwise
to increase idle speed (See
Figure 10).
Ensure that after adjustment, the
cutting head does not rotate at
idle speed.
Contact a service dealer if the
problem persists.
Grass wraps around
shaft housing and
fixed line head.
Cutting tall grass at
ground level. Cut tall grass from top down.
Operating trimmer at
part throttle. Operate trimmer at full throttle.
Knob hard to turn. Screw threads dirty or
damaged. Clean threads and lubricate with grease; if no improvement, replace
knob.
Oil drips from
silencer. Operating trimmer at part throttle. Operate trimmer at full throttle.
Improper mixing of oil/
fuel. Use fresh fuel and the correct synthetic 2-stroke oil mix.
Air filter dirty. Clean the air filer. Refer to “Cleaning
the Air Filter Screen” in the manual.
Note: If the unit exhibits specific performance problem(s) where the Problem Solving
section recommends a clockwise screw adjustment on the carburetor, but no adjust-
ments have been made since the original purchase, the unit should be taken to an
authorised service centre for repair. In most cases, the needed adjustment is a simple
task for the trained service representative.
JCB-LT26_960443001-01_Manual_final.indd 18JCB-LT26_960443001-01_Manual_final.indd 18 12/2/2010 4:20:20 PM12/2/2010 4:20:20 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
WARRANTY STATEMENT
CUTTING EDGE CONSTRUCTION TECHNOLOGY IN YOUR HANDS
In 1945, JCB began producing construction equipment. Today, we build the world’s
number one diggers, each one the product of our unswerving focus on innovation,
quality and engineering. JCB power tools are built to give you the same world beating
standards of performance. The same innovation, to always get the job done better,
the same quality, to never let you down, the same engineering heritage and expertise
that you can trust 100%.
JCB power tools are guaranteed against manufacturing defects for a period of 3
years (with registration) from the date of purchase. If your JCB power tool becomes
defective within this warranty period, we guarantee to:
Replace or repair all defective parts, free of charge, or
Repair products free of charge, or
Replace the unit with a new or re-conditioned unit, free of charge.
REGISTER NOW FOR YOUR EXTENDED JCB WARRANTY
With the extended 3 year warranty, JCB offers you additional protection which
extends far beyond the legally required periods and warranty conditions.
Thisserviceis availableto you atno cost ifyou register yournew JCB outdoorproduct
within 30 days of the purchase date.
All you need to do in order to receive this JCB service: register your machine online
at JCBDIY.COM
Our JCB service is only available within the U.K. & Ireland on Tel: [phone]
LIMITED WARRANTY
JCB warrants this outdoor product to be free of defects in material or workmanship
for 24 months from the date of purchase by the original purchaser, subject to the
limitations below. Please keep your invoice as proof of date of purchase.
This warranty is only applicable where the product is used for personal and
non-commercial purposes. This warranty does not cover damage or liability caused
by/due to misuse, abuse, accidental or intentional acts by user, improper handling,
unreasonable use, negligence, failure by end user to follow operating procedures
outlined in the user’s manual, attempted repair by non-qualified professional,
unauthorized repair, modification, or use of accessories and/or attachments not
specifically recommended by authorized party.
This warranty does not cover spark plugs, leaf collection bags, chainsaw chains &
chain bar, brush cutter blades, line trimmer heads, nylon cable or any part which
ordinary wear and tear results in required replacement during warranty period. Unless
JCB-LT26_960443001-01_Manual_final.indd 19JCB-LT26_960443001-01_Manual_final.indd 19 12/2/2010 4:20:20 PM12/2/2010 4:20:20 PM

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00
www.JCBdiy.com
specifically provided under applicable law, this warranty does not cover transportation
cost of consumable items.
This limited warranty is void if the product’s original identification (trade mark, serial
number, etc.) markings have been defaced, altered or removed or if product is not
purchased from an authorized reseller or if product is sold AS IS and/or WITH ALL
FAULTS.
Subject to all applicable local regulations, the provisions of this limited warranty
are in lieu of any other written warranty, whether express or implied, written or oral,
including any warranty of MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL WE BE LIABLE FOR SPECIAL, INCIDENTAL,
CONSEQUENTIAL DAMAGES. OUR MAXIMUM LIABILITY SHALL NOT EXCEED
THE ACTUAL PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.
This warranty is valid only in the U.K. & Ireland
WARRANTY CLAIMS
For guarantee claims, please contact JCB Customer Services. You will need to
submit proof of purchase in the form of a valid receipt that displays date and place of
purchase.
JCB CUSTOMER SERVICES 0845 600 5526
JCB – Chestnut House
Chestnut Avenue, Chandlers Ford,
Eastleigh, Hants, SO53 3LE – United Kingdom.
JCB-LT26_960443001-01_Manual_final.indd 20JCB-LT26_960443001-01_Manual_final.indd 20 12/2/2010 4:20:20 PM12/2/2010 4:20:20 PM