JEFF ROWLAND 535 Quick start guide

©"Jeff"Rowland"Design"Group"2017・All"Rights"Reserved
MODEL 535 STEREO AMPLIFIER
Operational Manual

SAFETY INSTRUCTIONS
The amplifier has been designed to operate at the highest level of efficiency and
performance in any normal operating situation; however, there are a few important
use and care principles that must be kept in mind when operating the amplifier:
§Read these instructions before operating the amplifier.
§Do not expose the amplifier to rain, moisture, or excessively damp conditions.
§Due to auto-ranging circuitry within the power supply, the audio performance
will not be affected by any voltage fluctuations within the operating voltage
range. The Model 535 can be operated at any mains voltage over the range of
85 to 265 VAC without any adjustments necessary.
§The Model 535 must not be modified in any way, other than according to
official service bulletins from JRDG (Jeff Rowland Design Group). Otherwise, the
factory warranty will be voided.
§When operating the Model 535, a properly grounded AC receptacle should be
used. A potential shock hazard may result if the supplied 3-wire, grounded AC
cable ground terminal is defeated or lifted or the unit is connected to a 2-wire
ungrounded AC outlet.
PROTECTIVE SYSTEMS
The Model 535 is equipped with internal and external fuses for protection against
excessive AC current draw; however, since no protection circuitry or system can
completely protect a product from every electrical hazard, certain precautions should
be observed. In the event of severe voltage hazards such as lightning or when the
amplifier will not be used for extended periods of time, the amplifier should be
unplugged from the AC mains to avoid potential damage to the internal circuitry. All
other audio/video system components should also be disconnected from AC mains
power as hazardous voltages can easily travel throughout an interconnected system.
The crossed-out wheeled bin is the European Union symbol for
indicating separate collection for electrical and electronic equipment.
This product contains electrical and electronic equipment which
should be reused, recycled or recovered and should not be
disposed of with unsorted regular waste. Please return the unit or
contact the authorized dealer from whom you purchased this
product for more information.
!
!2

LIMITED WARRANTY
Jeff Rowland Design Group, Inc. warrants the materials, workmanship, and proper
functioning of this product for a period of five years from the date of purchase as long
as the product was operated in accordance with its operating manual, the products
was not altered or improperly serviced or prepared, or if the product failed to function
from the beginning. In the event of such a failure, the product will be repaired or
replaced by Jeff Rowland Design Group, Inc. through one of its dealers. This warranty is
extended to the original purchaser only and is non-transferable to any secondary or
other purchaser.
In order to have this product repaired or replaced, the original purchaser must first
obtain the prior authorization of Jeff Rowland Design Group, Inc. or one of its dealers.
Purchaser must then return the product, PACKAGED IN ITS ORIGINAL CARTON,
FREIGHT PREPAID to: Jeff Rowland Design Group, Inc., 2911 North Prospect Street,
Colorado Springs, Colorado, 80907, or to one of its dealers.
Jeff Rowland Design Group, Inc. reserves the right to inspect any product which is
subject to any warranty claim prior to repairing or replacing it. Final determination of
warranty coverage lies solely with Jeff Rowland Design Group, Inc. Said determination
shall be made as soon as possible following receipt of the product. Jeff Rowland
Design Group, Inc. may, at its option, require from the purchaser, valid proof of
purchase (dated copy or photocopy of dealer's original invoice). Out-of-warranty
claims will be billed for labor, materials, return freight, and insurance as required. Any
product for which a warranty claim is accepted will be returned to the purchaser and
costs of shipping and insurance will be factory prepaid within the boundaries of the
USA. Units to be shipped outside of the USA will be shipped freight collect only. This
warranty gives the holder specific legal rights. The purchaser also has implied warranty
rights, and may also have other rights which may vary from state to state.
Jeff Rowland Design Group, Inc. strives to manufacture the very finest possible
equipment and therefore reserves the right to make changes in design and
improvements upon its previously manufactured models.
This product complies with European Low Voltage (2006/95/EC) and
Electromagnetic Compatibility (89/336/EEC) Directives when used
and installed according to this instruction manual. For continued
compliance servicing must be referred to qualified service
personnel.
!
!3

THE ABOVE WARRANTY IS THE SOLE WARRANTY GIVEN BY JEFF ROWLAND DESIGN
GROUP, INC. AND IS IN LIEU OF ALL OTHER WARRANTIES; ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE SHALL BE STRICTLY
LIMITED IN DURATION TO FIVE YEARS FROM THE ORIGINAL DATE OF PURCHASE AND
UPON THE EXPIRATION OF THIS FIVE YEAR WARRANTY PERIOD, JEFF ROWLAND DESIGN
GROUP, INC. SHALL HAVE NO FURTHER OBLIGATION OF ANY KIND WHETHER EXPRESSED
OR IMPLIED.
Jeff Rowland Design Group, Inc. does not authorize any third party, including any
dealer or representative, to assume any liabilities on its behalf or to make any
warranties on its behalf unless authorized to do so.
Warranty registration cards must be completed and mailed to Jeff Rowland Design
Group, Inc. within thirty (30) days of the date of purchase. If this product is used in a
commercial or industrial application, then special warranty exclusions may apply.
Contact your dealer or Jeff Rowland Design Group, Inc. for information regarding our
commercial warranty policies.
MANUAL INTENT
This manual is intended to make installation and use of this product as easy as
possible. Information in this document has been carefully checked for accuracy at the
time of printing; however, Jeff Rowland Design Group, Inc.'s goal is one of continuous
improvement, therefore design and specifications are subject to change without prior
notice. If you notice any errors please feel free to email us at:
[e-mail].
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic or
other means, in any form, without prior written permission of the manufacturer. All
trademarks and registered trademarks are the property of their respective owners.
© Copyright Jeff Rowland Design Group, Inc 2017
!4

NOTE FROM JEFF ROWLAND DESIGN GROUP
elcome to the Jeff Rowland Design Group “family” and congratulations on
your purchase of what is unquestionably one of the world’s finest amplifiers.
With its combination of features such as precision electronic circuitry, exceptional
efficiency, and accurately machined chassis components throughout, your Model 535
will offer you many years of musically satisfying enjoyment.
Please take a few minutes to read the remainder of this Owner’s Manual before
proceeding with the installation of the amplifier. A thorough understanding of the
operational features will allow you to gain the maximum performance and ease of use
for which this amplifier was designed.
Please note that your Model 535 serial number begins with the letters “SM”. Please
include this number with any correspondence regarding your Model 535. It has been
my intent to create an audio component of enduring value that reflects the highest
ideals of musical and artistic expression. I hope these qualities will enhance your
musical experience.
If you have any additional questions regarding the installation or operation of the
MODEL Model 535, please contact your authorized Jeff Rowland Design Group dealer
or check the Jeff Rowland Design Group web site at http://jeffrowlandgroup.com.
Enjoy the music!
Jeff Rowland!
President, Jeff Rowland Design Group
!5
W

TABLE OF CONTENTS
Design Features
7
Maintenance and Care
9
Unpacking and Placement
10
Front Panel Operation
11
Rear Panel Connections
12
Specification
14
!6

DESIGN FEATURES
MACHINED ALUMINUM CHASSIS: Precision-machined chassis, milled from a solid block of
aircraft grade aluminum, provides exceptional thermal heat transfer/dissipation, RFI/
EMI shielding, resonance control, and minimizes micro-phonically induced micro-
vibrations from any source.
CERAMIC CIRCUIT BOARDS: Critical audio circuits are implemented on mil-spec, multi-
layer, low dielectric constant, Rogers™ ultra-rigid ceramic circuit board substrate for
extremely low energy retention and absorption. Large low impedance ground planes
areas for extended internal star-grounding.
BALANCED TOPOLOGY: Inherent cancellation effects of balanced topology implemented
throughout power and input/output circuits ensure reduced distortion and noise
under dynamic signal conditions.
HIGH-PRECISION SURFACE MOUNT COMPONENTS: Extensive use of Lead (Pb)-free, low
temperature coefficient, active and passive surface-mount components results in
significantly smaller loop areas, reduced circuit capacitance and inductance, and
introduces less noise than conventional leaded components.
THIN-FILM RESISTORS: All resistors are low noise, 0.1% thin-film type for extremely low
thermal noise which complement the low-noise characteristics of the active circuitry.
TEFLON INSULATED WIRES:All signal carrying input and output wires are teflon insulated,
for low dielectric energy storage, ensuring that each audio note naturally decays into
the deeper silence of the music.
TRANSFORMER-COUPLING AND ISOLATION: Transformer coupled input circuitry provides
universal component compatibility and virtually eliminates ground loop noise and RFI/
EMI. Transformer coupling ensures identical amplifier overall gain when using
unbalanced input adapters.
ACTIVE POWER FACTOR CORRECTION: Power Factor Correction (PFC) integrated into
the power supply reduces AC line harmonic noise pollution and increases AC line
power utilization to 97%.
HIGH-EFFICIENCY SWITCH-MODE POWER SUPPLY: Highly efficient, compact, light weight,
switch-mode power supply provides optimum voltage regulation for all circuits and
operating conditions, and allows for quiet operation over a wide range of AC mains
power sources.
!7

BINDING POSTS: CE approved speaker output terminals require no tools for secure, low
resistance connections.
FRONT PANEL STANDBY BUTTON: Illuminated front panel push-button switches the
amplifier into standby mode (<0.3 watt consumption). An internal switch allows the
user to dim the front panel indicator light "ring" or shut off the light altogether when
the amplifier is powered on.
REMOTE ON/OFF: A 1/8”(3.5mm) mini plug connector on rear panel permits amplifier
power on/standby switching in remote and home theater applications.
!8

MAINTENANCE AND CARE
All Jeff Rowland Design Group products are designed to provide a lifetime of
enjoyment and listening pleasure.
The chassis is sealed to prevent dust from entering the interior of the chassis and thus
should never need interior cleaning during the lifetime of the product. All internal
circuitry is maintenance-free such that no adjustments of any kind are necessary over
the lifetime of the product. If the amplifier is ever in need of service, updating, or
upgrading, it should only be returned to an authorized repair facility or technician for
servicing.
The front panel of the unit is precision-machined in a unique process that incorporates
a diamond tipped cutting tool. This process was refined over many years to produce an
attractive and unique appearance. Because the surface is not finished in the typical
fashion of most audio and video equipment, there are a few rules that must be kept in
mind when cleaning the equipment.
NOTE: PLEASE ALLOW THE FRONT PANEL, WHICH IS COATED WITH AN AUTOMOTIVE-GRADE
POLYURETHANE FINISH, TO CURE FOR 6 MONTHS BEFORE ATTEMPTING TO CLEAN IT. THIS WILL
PREVENT SMALL SCRATCHES FROM MARRING THE SURFACE BEFORE THE SURFACE COATING HAS
HAD A CHANCE TO HARDEN COMPLETELY.
WARNING: THE FRONT PANEL OF THE UNIT SHOULD NEVER BE CLEANED WITH ANYTHING OTHER
THAN A VERY SOFT COTTON CLOTH AND PLAIN WATER OR FINE OIL-BASED FURNITURE POLISH.
BECAUSE OF THE FINE FINISH OF THE FRONT PANEL, USE OF ANY OTHER CLEANING AGENT MAY
PERMANENTLY SCRATCH THE FINISH.
The top and bottom cover, sides and bottom are protected by a durable black
anodized finish and can be cleaned with a soft cotton cloth (such as an optical lens or
microfiber cleaning cloth) dampened with plain water. Water should be applied
directly to the cloth and not the chassis. A very mild plastic or glass cleaner that does
not contain ammonia may also be used. If a mark has been left on the chassis, do not
use any type of abrasive or chemical cleaner to remove the mark.
If you have any questions about the care or cleaning of your Model 535, please
contact your dealer before attempting to clean the chassis. The use of a cleanser or
abrasive to clean the chassis that has not been approved by the factory will almost
certainly damage the finish and will not be covered under warranty.
!9

UNPACKING AND PLACEMENT
INITIAL INSPECTION
Inspect the shipping container for damage. If any portion of the shipping container,
packing material, amplifier, or accessories are damaged or missing, notify your dealer
and the shipper (if a claim is to be made) immediately.
NOTE: MANY SHIPPERS REQUIRE NOTIFICATION AND INSPECTION WITHIN 24 HOURS OF
DELIVERY TO DETERMINE THE NATURE OF DAMAGES INCURRED.
Your Model 535 has undergone extensive performance evaluations, listening tests,
quality control inspections, and a minimum 72-hour burn-in period prior to shipment
and should therefore be in perfect operating condition upon delivery. If the amplifier
does not operate correctly, please notify your dealer immediately.
We strongly suggest that you save all of the packing materials. If the amplifier is
returned to your dealer or Jeff Rowland Design Group, the original packing materials
must be used for shipment to avoid possible damage. Neither Jeff Rowland Design
Group nor the shipper can be held responsible for damages incurred during transit if
the original factory packing is not used. All factory returns require that Jeff Rowland
Design Group issue a Return Authorization (RA) number prior to shipment.
UNPACKING
Carefully unpack amplifier chassis and power supply from original packing box.
Remove all accessory items from the accessory box. Accessories include:
§1 Detachable IEC AC Power Cord
§Operational Manual
§Warranty Card
IMPORTANT: RETAIN ALL PACKING MATERIALS FOR FUTURE TRANSPORT. SHIPPING PRODUCT IN
INADEQUATE PACKING MATERIALS MAY VIOLATE THE JEFF ROWLAND DESIGN GROUP
MANUFACTURER’S WARRANTY.
!10

FRONT PANEL OPERATIONS
1. FRONT PANEL POWER BUTTON.Press this button to operate the amplifier. Press
again to place the amplifier in Standby Mode.
2. POWER INDICATOR RING. This ring will illuminate white when the amplifier is
operational. Ring will not be illuminated when the amplifier is in Standby Mode.
Figure 1: Front Panel
!11

REAR PANEL CONNECTIONS
1. INPUT: Left Channel Balanced XLR: Use XLR to RCA input adapter (not included)
for use with RCA interconnects.
2. INPUT: Right Channel Balanced XLR; Use XLR to RCA input adapter (not included)
for use with RCA interconnects.
3. INPUT: Bridged Mono XLR; Use XLR to RCA input adapter (not included) for use
with RCA interconnects.
4. LOUDSPEAKER OUTPUT RIGHT CHANNEL:Connect to right Loudspeaker, 2 to 16
ohm impedance, for Stereo Operation.
5. LOUDSPEAKER OUTPUT LEFT CHANNEL: Connect to left Loudspeaker, 2 to 16
ohm impedance, for Stereo Operation.
6. LOUDSPEAKER MONO OUTPUT: Connect to Loudspeaker, 4 to 16 ohm
impedance, for mono Operation.
7. STEREO/BRIDGED MODE SWITCH: Configures Model 535, as either a stereo or
mono amplifier. When configured as a single mono amplifier, the overall gain of
the amplifier is automatically adjusted to maintain the same gain as in stereo
operation.
8. REMOTE ON/OFF: A 1/8” (3.5 mm) mini-plug jack is provided on the rear panel of
the Model 535 for remotely switching the amplifier between Operational and
Standby modes. Applying a continuous 6 to 15 volts DC to the connector will
override the front panel power button and place the amplifier into operational
mode.The Model 535 operational mode can also be controlled by another audio
component with the proper circuitry, through the remote on/off connector.
Figure 2: Rear Panel Connections
!12

9. AC MAINS INPUT CONNECTOR: Install an AC Power Cable, supplying 85 - 230
volt AC , into the AC mains input connector.
10. FUSE HOLDER: Supplied with 6.3A 250V slow-blow or time-delay type fuse (MDL).
Always replace with similar rating and type fuse.!
!13

SPECIFICATIONS
Output Power
250 watts @ 8 ohms /500 watts @ 4 ohms,
100-230 Vac
900 watts @ 8 ohms, Mono, 230 Vac
700 watts @ 8 ohms, Mono, 100-120 Vac
Frequency Response
5 Hz – 70 kHz, -3 dB
Dynamic Range
120 dB, A weighted
Output Noise
55 microvolts, A weighted
Transient Intermodulation
Distortion
(TIM), 0.0035% @10 watts
Intermodulation Distortion
(CCIF,18 kHz + 19 kHz) 0.0015%, @10 watts
Input Impedance
40k ohms
THD + Noise
< 0.05%, 20 Hz -20 kHz, 0.003% @ 1 watt, 1 kHz
Damping Factor
> 1000 @ 1 kHz
Output DC offset
< +/- 1.0 millivolts
Overall Gain
26/26 dB Stereo/Mono
Maximum Output Capacitive Load
1.0 microfarad
Overall Amplifier Efficiency
89% @ 250 watts
Common Mode Rejection Ratio
> 90 dB, 20 Hz - 20 kHz
Inputs
1 pair (XLR) Stereo, One (XLR) Mono, pin 2 +
Outputs
1 pair binding posts Stereo, One binding post
Mono
Power Consumption Idle
9 watts
Power Consumption Standby
0.3 watts
Power Factor
0.97, 120 Vac, rated output
Amplifier Weight
22 lbs. / 9.97kg
Amplifier Dimensions (h/w/d)
2.85” x 15.5” x 11.0” / 72mm x 381mm x 279mm
!14