Jegs 555-23560 User manual

OPERATING INSTRUCTIONS AND PART MANUAL
555-23560
9 LITER MANUAL FLUID EXTRACTOR
CAREFULLY READ THIS MANUAL BEFORE OPERATING THE UNIT

WARNING: Please read all instructions and warnings
carefully before use
Do not use the unit with gasoline.
For security reasons, do not use the unit to extract or store dangerous
chemicals, poison, acid, alkaloid, or solvents.
Do not use the unit to extract, siphon or store petroleum or other highly
inflammable liquids.
Do not throw, drop or mishandle the unit.
Do not disassemble, tamper with or modify the unit for any other purpose
than what it was originally intended for.
Do not store either the unit or suction tubes near or in areas of high
temperatures, direct sunlight, rain or snow.
The unit must be instantly, drained, washed and cleaned after each use.
1

Extractor Unit
Tube Storage Unit
Main Suction Tube
Extracting Tube
Brake Tube With
Rubber Fitting
Contents of Package:
Instructions Manual
2

Extractor Unit Components
A. Cover Housing
B. Release Button
C. Reservoir Tank
D. Tube Storage Unit
E. Footboard
F. Base
G. Hand Pump
H. Handle
I. Fluid Outlet Housing
J. Fluid Inlet Coupler
K. Main Suction Tube
L. Extracting Tube
M. Brake Tube W/ Rubber Fitting
3

9 LITER MANUAL FLUID EXTRACTOR
OPERATING INSTRUCTIONS
Notes:
When using the Manual Fluid Extractor unit
to extract engine oil, first you need to make
sure the vehicle is level, and then run the
engine for about 5 minutes to warm the oil
and allow any sludge or contamination
within the oil to mix.
Operating Steps:
1. To set up the Tube Storage Unit ( D ) into the two hooks of Reservoir Tank ( C )
2. Remove the oil dipstick from the engine.
4

3. Insert the Extracting Tube ( L ) into
the dipstick hole until it reaches the
bottom of the oil pan.
Connect the Main Suction Tube ( K )
into the Fluid Inlet Coupler ( J ) with
the Main Suction Tube Adapter.
The Main Suction Tube ( K ) will
connect to the Extracting Tube ( L )
with the Extracting Tube Adapter.
4. Lift the Handle ( H ) of the
Hand Pump ( G ) to the top position
and press it to the bottom position
repeatedly.
The Extractor Unit will start operation.
5. When the fluid inside the extractor tank
reaches 〝Full〞position, the Extractor
Unit will shut off automatically, the
Handle ( H ) of the Hand Pump
( G ) will lock. Push the Release
Button ( B ) on the side of the
Cover Housing (A ), and then press
the Handle ( H )of the Hand
Pump( G ) to the bottom position
to release Hand Pump from locked
position.
5

6. Disconnect the Main Suction Tube ( K ) and the Extracting Tube ( L ) remove them
from the dipstick hole. Open the Fluid Inlets Coupler ( J ) and dispose of the oil or
fluid in accordance with the laws and guidelines in your state.
Trouble shooting:
No.
Trouble Cause
Trouble shooting
1
When the Extractor Unit is
working
, but it can’t suck the fluid
any more
Check that the extraction tube has been
inserted completely and firmly or has slipped
out? Inspect that the fluid has been
completely emptied or not? Check the fluid
inside the extractor tank level – if “Full”,
empty tank.
6

7

PART LIST
Index
Part No. Description Unit Index
Part NO.
Description Unit
1 PX90M-01 Cover Housing 1 26 PX90-12 Fixed Strip 1
2 PX90-49 Release Button 1 27 PX90-35
Screwψ4x10mm
3
3 PX90-49-1 Spring 1 28 PX90-36 Screw M8x16mm 2
4 PX90-06 Fluid Inlet Coupler 1 29 PX90M-29 Ring Seal 1
5 PX90-14
O Ring 25.2xψ2.7mm
1 30 PX90-18 Shaft 1
6 PX90-05 Fluid Outlet Housing 1 31 PX90-28 Oil Seal 1
7 PX90-32
O Ring 31xψ1.0mm
1 32 PX90-27 Holder 1
8 PX90-09 Lock Nut 1 33 PX90-47 Flat Washer 2
9 PX90-49-6 Locking Bushing 1 34 PX90-46 Piston Spacer 1
10 PX90-49-3 Shaft 1 35 PX90-45 Piston 1
11 PX90-49-5 Spring 1 36 PX90-44 Hex Nut M8 1
12 PX90-51 Check Valve 1 37 PX90-19 Holder 1
13 PX90M-13 Safety Cup 1 38 PX90M-17 Alum. Tube 1
14 PX90-49-5 Spring 1 39 PX90M-23 Alum. Tube Base 1
15 PX90M-15 Bracket Base 1 40 PX90-38 Screw M5x16mm 1
16 PX90M-16 Arm 1 41 PX90-39 Nut M5 7
17 PX90-13
O Ring 154.3xψ3.5mm
1 42 PX90-16 Handle 1
18 PX90-02 Reservoir Tank 1 43 PX90-20 Cap 2
19 PX55-19 Pin 2 44 PX90-43 Screw M5x20MM 6
20 PX55-25 Screw
ψ
3.8x10mm 2 45 PX90-30 Main Suction Tube
W/Adapter 1
21 PX55-20 Float 1 46 PX90-31
Extracting Tube
W/Adapter
1
22 PX90-04 Tube Storage Unit 1 47 PX90-68 Connecter 2
23 PX90-03 Base 1 48 PX90-29 Brake Tube
W/Rubber Fitting 1
24 PX90-34
Screwψ6x15mm
4
25 PX90-11 Footboard 1
The type’s specifications may be changed without notice
8