Jet IBG-8VS User manual

IBG-8VS
BENCH GRINDER
Original:
GB
Operating Instructions
JPW (Tool) AG.
Tämperlistrasse 5
CH-8117 Fällanden
Switzerland
Phone [phone]
Fax [phone]
www.jettools.com
M-578208-RU 2018-01

2
1.0 IMPORTANT SAFETY
INSTRUCTIONS
WARNING –To reduce risk of injury:
1. Read and understand the entire owner's manual
before attempting assembly or operation.
2. Read and understand the warnings posted on the
machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace warning labels if they become obscured
or removed.
4. This bench grinder is designed and intended for
use by properly trained and experienced
personnel only. If you are not familiar with the
proper and safe operation of a bench grinder, do
not use until proper training and knowledge have
been obtained.
5. Do not use this bench grinder for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result from
that use.
6. Always wear protective eye wear when operating
machinery. Eye wear shall be impact resistant,
protective safety glasses with side shields which
comply with ANSI Z87.1 specifications. Use of eye
wear which does not comply with ANSI Z87.1
specifications could result in severe injury from
breakage of eye protection. (Everyday eyeglasses
only have impact resistant lenses; they are NOT
safety glasses.)
7. Use the grinder’s eye shields and spark guards.
Also use respiratory protection if cutting operation
is dusty.
8. Wear proper apparel. Do not wear loose clothing,
neckties, rings, bracelets, or other jewelry which
may get caught in moving parts. Non-slip footwear
is recommended. Wear protective hair covering to
contain long hair.
9. Wear protective clothing such as apron or safety
shoes, where the grinding activity presents a
hazard to the operator.
10. Wear ear protectors (plugs or muffs) if the
particular work requires it.
11. CALIFORNIA PROPOSITION 65 WARNING:
This product contains chemicals known to the
State of California to cause cancer, or birth defects
or other reproductive harm.
12. This product, when used for welding, cutting, or
working with metal, produces fumes, gases, or
dusts which contain chemicals known to the State
of California to cause birth defects and, in some
cases, cancer. (California Health and Safety Code
Section 25249.5 et seq.)
13. Do not operate this machine while tired or under
the influence of drugs, alcohol or any medication.
14. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
15. Make certain the machine is properly grounded.
16. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
17. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine before
turning it on.
18. Keep safety guards in place at all times when the
machine is in use. If removed for maintenance
purposes, use extreme caution and replace the
guards immediately after completion of
maintenance.
19. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may affect
its operation. A guard orother part thatis damaged
should be properly repaired or replaced.
20. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
21. Keep the floor around the machine clean and free
of scrap material, oil and grease.
22. Keep visitors a safe distance from the work area.
Keep children away.
23. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
24. Give your work undivided attention. Looking
around, carrying on a conversation and “horse-
play” are careless acts that can result in serious
injury.
25. Keep proper footing and balance at all times so
that you do not fall into or lean against the grinding
wheel or other moving parts. Do not overreach or
use excessive force to perform any machine
operation.
26. Disconnect grinder from power source before
servicing and when changing abrasive wheels.
27. Use recommended accessories. The use of
improper accessories may cause risk of injury to
persons.

3
28. Turn off the machine before cleaning. Use a brush
to remove chips or debris —do not use your
hands.
29. Never leave the grinder running unattended. Turn
power off and do not leave machine until wheels
come to a complete stop.
30. Remove loose items and unnecessary work
pieces from the area before starting the grinder.
31. Don’t use in dangerous environment. Don’t use
power tools in damp or wet location, or expose
them to rain. Don’t use this grinder in a flammable
environment. Keep work area well lighted.
32. Keep work area clean. Cluttered areas and
benches invite accidents.
33. Use the right tool. Don't force tool or attachment to
do a job for which it was not designed.
34. Use proper extension cord. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will draw.
An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Table 1 (see sect. 6.2) shows the correct size to
use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier
the cord.
35. Maintain tools with care. Keep tools sharp and
clean for best and safest performance. Follow
instructions for lubricating and changing
accessories.
36. Direction of feed: Feed work into a blade or cutter
against the direction of rotation of the blade or
cutter only.
37. Do not overtighten wheel nut.
38. Frequently clean grinding dust from beneath
grinder.
39. Use grinding wheel suitable for speed of grinder.
40. Inspect abrasive wheels for cracks or other forms
of damage. Perform a “ring test” to check wheel
integrity. Do not use a faulty or damaged wheel.
41. Verify that maximum RPM of abrasive wheels is
compatible with speed of grinder. Do not remove
the blotter (label) from either side of a grinding
wheel.
42. Allow abrasive wheels to reach full RPM before
starting the grinding operation.
43. Do not crowd the work so that the wheels slow.
44. Tool rests should be adjusted to approximately
1/16” from wheel surface.
45. Do not grind on the side of a wheel; do all work on
the grinding face or edge near the tool rest.
46. Do not grind aluminum or magnesium, as these
may pose a fire hazard.
47. Use only the flanges that are furnished with the
grinder.
48. Do not start the grinder while a workpiece is
contacting a grinding wheel.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious, or possibly even fatal,
injury.

4
2.0 Table of contents
Section Page
1.0 IMPORTANT SAFETY INSTRUCTIONS.......................................................................................................2
2.0 Table of contents............................................................................................................................................4
3.0 About this manual ..........................................................................................................................................5
4.0 Specifications.................................................................................................................................................6
4.1 Mounting hole dimensions..........................................................................................................................7
5.0 Setup and assembly.......................................................................................................................................8
5.1 Unpacking ..................................................................................................................................................8
5.2 Carton contents..........................................................................................................................................8
5.3 Tools required for assembly.......................................................................................................................8
5.4 Securing the grinder...................................................................................................................................8
5.5 Assembling eye shield brackets to spark guards.......................................................................................9
5.6 Installing spark guards/brackets.................................................................................................................9
5.7 Eye shields.................................................................................................................................................9
5.8 Tool rests....................................................................................................................................................9
5.9 Dust hose...................................................................................................................................................9
6.0 Electrical connections ..................................................................................................................................10
6.1 Grounding instructions .............................................................................................................................10
6.2 Extension cords........................................................................................................................................10
6.3 Voltage conversion...................................................................................................................................11
7.0 Operation .....................................................................................................................................................11
7.1 Operating controls....................................................................................................................................11
7.2 Precautions ..............................................................................................................................................11
8.0 Adjustments .................................................................................................................................................12
8.1 Eye shield tilt adjustment..........................................................................................................................12
8.2 Spark guard..............................................................................................................................................12
8.3 Tool rest ...................................................................................................................................................12
9.0 User-maintenance........................................................................................................................................12
9.1 Ring test...................................................................................................................................................12
9.2 Care of grinding wheels............................................................................................................................12
9.3 Changing wheels......................................................................................................................................12
9.4 Wheel balancing.......................................................................................................................................13
9.5 Dressing the wheels.................................................................................................................................14
9.6 Wire wheel brushes..................................................................................................................................14
9.7 Cleaning...................................................................................................................................................14
9.8 Lubrication................................................................................................................................................14
9.9 Additional servicing ..................................................................................................................................14
10.0 Troubleshooting IBG-8VS Bench Grinder..................................................................................................15
10.1 General electrical and mechanical problems .........................................................................................15
10.2 Digital readout error codes.....................................................................................................................16
11.0 Optional accessories..................................................................................................................................17
12.0 Replacement Parts.....................................................................................................................................17
12.1.1 IBG-8VS Variable Speed Grinder –Exploded View............................................................................18
12.1.2 IBG-8VS Variable Speed Grinder –Parts List.....................................................................................19
12.2.1 IBG-Stand Assembly (OPTIONAL) –Exploded View..........................................................................21
12.2.2 IBG-Stand Assembly (OPTIONAL) –Parts List ..................................................................................21
12.3.1 DBG-Stand Assembly (OPTIONAL) –Exploded View........................................................................22
12.3.2 DBG-Stand Assembly (OPTIONAL) –Parts List.................................................................................22
13.0 Electrical Connections –IBG-8VS Grinder ..................................................Error! Bookmark not defined.
14.0 Warranty and Service...................................................................................Error! Bookmark not defined.

5
3.0 About this manual
This manual is provided by JET, covering the safe operation and maintenance procedures for a JET IBG-8VS
Variable Speed Bench Grinder. This manual contains instructions on installation, safety precautions, general
operating procedures, maintenance instructions and parts breakdown. Your grinder has been designed and
constructed to provide consistent, long-term operation if used in accordance with the instructions set forth in this
document.
The operator is encouraged to familiarize him/herself with ANSI B7.1 –Safety Requirements for Use, Care and
Protection of Abrasive Wheels.
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our
web site: www.jettools.com.
Retain this manual for future reference. If the grinder transfers ownership, the manual should accompany it.
Read and understand the entire contents of this manual before attempting assembly or
operation! Failure to comply may cause serious injury!
Register your product using the mail-in card provided, or register online:
http://www.jettools.com/us/en/service-and-support/warranty/registration/

6
4.0 Specifications
Model number
IBG-8VS
Stock number
578208-RU
Motor and Electricals
Motor type
Totally enclosed fan-cooled induction with inverter
Horsepower (true output)
0.75 kW
Motor phase
3
Voltage
230
Input power
single phase
Cycle
50 Hz
Listed FLA (full load amps)
3.5 A
On/off switch
TACT switch
Motor speed
Variable, 900-3600 /min
Power cable size
H05VV-F 1.0mm²x 3G, 182 cm
Power plug installed
VDE, 250V/16A
Recommended circuit size 1
15A
Sound emission without load 2
75 dB at 1 M
Arbor and grinding wheels
Arbor diameter
15.875 mm
Wheel size (dia. x width)
200 x 25 mm
Wheel bore
15.875 mm
Wheel material
aluminum oxide
Wheel grits
36 and 60
Wheel flange diameter
85 mm
Wheel speed
Variable, 900-3600 RPM
Arbor nut maximum tightening torque
270 kgf•cm
Tool rest distance to wheel
adjustable
Main materials
Arbor
Steel
Base
Cast iron
Motor housing
Sheet metal
Inner wheel guard
Cast iron
Outer wheel guard
Aluminum
Flange washers
Cast iron
Tool rests
Cast iron
Eye shields
Clear polycarbonate
Spark guards
Steel
Knobs
Polymide
Connector sleeve
ABS
T-fitting
ABS
Dimensions
Mounting hole centers
215 mm
Mounting hole diameters
11 mm
Footprint (width x depth)
241.6 x 205 mm
Assembled dimensions (LxWxH)
572 x 340 x 354 mm
Shipping dimensions (LxWxH)
580 x 342 x 356 mm
Dust/swarf collection
Dust port outside diameter
63.5 mm
Required min. extraction volume
350 CFM
Weights
Net weight
30.14 kg
Shipping weight
32.55 kg

7
1subject to local/national electrical codes.
2 The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace
conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks
involved only.
L = length, W = width, H = height
n/a = not applicable
The specifications in this manual were current at time of publication, but because of our policy of continuous
improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring
obligations.
4.1 Mounting hole dimensions
Figure 4-1: IBG-8VS hole centers

8
5.0 Setup and assembly
5.1 Unpacking
Separate all parts from the packing material. Check
each part against sect. 5.2, Carton contents,and
make certain that all items are accounted for before
discarding any packing material. (Check grinder first
to verify if any parts have been pre-mounted.)
5.2 Carton contents
Refer to Figure 5-1.
1 ea Grinder (not shown)
1 ea Dust hose with T-connector (not shown)
1 ea Spark guard –Left (A)
2 ea Lock knob (B)
1 ea Spark guard –Right (C)
1 ea Eye shield bracket –Left (D)
2 ea Flat washer, 1/4" (E)
1 ea Eye shield bracket –Right (F)
2 ea Eye shield plate (G)
4 ea Truss head screw, 3/16 x 1/2”(H)
4 ea Hex cap screw, 3/8 x 3/4" (J)
4 ea Hex cap screw, 3/8 x 1/2" (K)
8 ea Flat washer 3/8” (L)
1 ea Tool rest –Left (M)
1 ea Tool rest –Right (N)
2 ea Eye shield (O)
1 ea Wheel dresser (P)
5.3 Tools required for assembly
Cross-point (Phillips) screwdriver
14mm (or adjustable) wrench
The IBG-8VS bench grinder requires only the
assembly of the eye shields and tool rests.
Additional tools may be needed for fastening the
grinder to a workbench or stand. For your safety, do
not plug the grinder into a power source until all
assembly and adjustments are complete.
Be sure that the bench grinder
is unplugged and the power switch is in the OFF
position. Do not plug in the grinder to power
until it is inspected for shipping damage, fully
assembled, and moved to its permanent
location. Failure to comply may cause serious
injury.
Do not operate this grinder
without all guards and shields in place and in
working order. Failure to comply may cause
serious injury.
Chipped or cracked wheels can
break up and cause serious damage to the
grinder and/or severe injury to the operator.
Regularly inspect wheels for damage.
Figure 5-1: Carton contents
5.4 Securing the grinder
To prevent the machine from moving during
operation, it should be securely mounted to a work
surface or grinder stand. Fasteners for mounting are
not included with the grinder.
1. Align the mounting holes on the grinder with
predrilled holes in a bench or grinder stand.
Figure 4-1 shows hole centers for mounting.
2. Insert M8 (or 5/16”) bolts through the holes and
tighten, using washers and nuts.
An optional pedestal stand (not included) is
available from JET for your grinder. See sect. 11.0.

9
IMPORTANT: The grinder’s base plate contains
ventilation holes for keeping the circuit board at an
acceptable temperature. These holes should not be
obstructed. If the rubber pads are removed for
mounting to a table, allow an opening in the table
below the grinder for air circulation. However, it is
recommended the rubber pads be left on, as they
allow air circulation as well as vibration dampening.
5.5 Assembling eye shield brackets
to spark guards
Refer to Figure 5-2.
Note: Spark guards (A) and eye shield brackets (D)
are marked Lfor left side assembly and Rfor right
side assembly.
1. Assemble the left spark guard and eye shield
bracket using Figure 5-2 as a guide. Make sure
spark guard and bracket are both marked L.
2. Install the right assembly in the same manner.
Figure 5-2: brackets to spark guards
5.6 Installing spark guards/brackets
Refer to Figure 5-3.
1. Install the left spark guard and mounting
bracket assembly to the left wheel housing with
two 3/8 x 1/2” hex cap screws (K) and two 3/8"
flat washers (L).
2. Install the right spark guard and mounting
bracket in the same manner.
3. The spark guards (A1) should be adjusted to
within 1/16" of the grinding wheel surface or
other accessory being used. As the wheel
wears down, the spark guards must be re-
adjusted to maintain this 1/16" distance.
5.7 Eye shields
Refer to Figure 5-3.
The eye shields (O) are identical and will fit on either
side of the grinder.
1. Insert two 3/16” x 1/2” truss head screws (H)
through the bracket, eye shield (O), and plate
(G) which contains threaded mounting holes.
2. Tighten the screws (H).
5.8 Tool rests
Refer to Figure 5-3.
Note: There is a left and a right tool rest. Refer to
Figure 5-3 for proper orientation.
1. Install the left tool rest (M) by inserting two 3/8"
x 3/4" hex cap screws (J) through two 3/8" flat
washers (L), through the tool rest (M), into the
wheel housing.
2. Install the right tool rest in the same manner.
3. The tool rests should be adjusted to within 1/16"
of the grinding wheel or other accessories being
used. As the wheel wears down, the tool rest
must be readjusted to maintain a 1/16"
clearance.
Figure 5-3: guards and tool rests
5.9 Dust hose
Refer to Figure 5-4.
Slide the connector sleeves onto the T-fitting, and
onto the flanges of the wheel guards, as shown. The
T-connector has a 2-1/2” outside diameter port for
attaching a dust collection system.
Figure 5-4: dust hose

10
6.0 Electrical connections
Electrical connections should
be made by a qualified electrician in compliance
with all relevant codes. This tool must be
properly grounded.
The IBG-8VS Grinder is prewired for 115V single
phase power, and is supplied with a plug designed
for use on a circuit with a grounded outlet that looks
like the one pictured in A, Figure 6-1. The grinder
may be converted to 230V single phase power, see
sect. 6.3.
Before connecting to power source, be sure switch
is in off position.
It is recommended that the grinder be connected to
a 15-amp circuit with circuit breaker or fuse. If using
fuses, they should be time-delay fuses marked “D”.
Local codes take precedence over
recommendations.
Figure 6-1: plug configurations
6.1 Grounding instructions
1. All Grounded, Cord-connected Tools:
This tool must be grounded. In the event of a
malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with
an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface
that is green with or without yellow stripes is the
equipment-grounding conductor. If repair or
replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding
conductor to a live terminal.
Check with a qualified
electrician or service personnel if the grounding
instructions are not completely understood, or if
in doubt as to whether the tool is properly
grounded. Failure to comply may cause serious
or fatal injury.
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug.
Repair or replace damaged or worn cord
immediately.
2. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating less than
150 volts:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in A, Figure
6-1. An adapter, shown in Band C, may be used to
connect this plug to a 2-pole receptacle as shown in
Bif a properly grounded outlet is not available. The
temporary adapter should be used only until a
properly grounded outlet can be installed by a
qualified electrician. This adapter is not permitted in
Canada. The green-colored rigid ear, lug, and the
like, extending from the adapter must be connected
to a permanent ground such as a properly grounded
outlet box.
3. Grounded, cord-connected tools intended for use
on a supply circuit having a nominal rating between
150 - 250 volts, inclusive:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in D, Figure
6-1. A grounding plug may be installed, that looks
like the plug illustrated in D; or the grinder may be
“hard-wired” to a panel, provided there is a
disconnect for the operator.
Make sure the tool is connected to an outlet having
the same configuration as the plug. No adapter is
available or should be used with this tool. If the tool
must be reconnected for use on a different type of
electric circuit, the reconnection should be made by
qualified service personnel; and after reconnection,
the tool should comply with all local codes and
ordinances.
6.2 Extension cords
The use of extension cords is discouraged. Try to
position equipment near the power source. If an
extension cord becomes necessary, use only three-
wire extension cords that have three-prong
grounding type plugs and three-prong receptacles
that accept the tool's plug. Replace or repair
damaged or worn cord immediately.
Make sure your extension cord is good condition,
and is heavy enough to carry the current your
product will draw. An undersized cord will cause a
drop in line voltage resulting in loss of power and
overheating.

11
Table 1 shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt,
use the next heavier gage. The smaller the gage
number (AWG), the heavier the cord.
Ampere
Rating
Volts
Total length of
cord in feet
More
Than
Not
More
Than
120
240
25
50
50
100
100
200
150
300
AWG
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not
Recommended
Extension Cord Recommendations
Table 1
6.3 Voltage conversion
To change voltage input to 230-volt on the IBG-8VS
Grinder, remove existing plug from grinder cable
and attach a UL/CSA listed plug designed for 230V
power.
7.0 Operation
Always use approved safety
glasses or face shield while operating grinder.
Failure to comply may cause serious injury.
A bench grinder is designed for hand-grinding
operations such as sharpening chisels,
screwdrivers, drill bits, removing excess metal, and
smoothing metal surfaces.
A Medium Grain Abrasive Grinding Wheel is
suitable for rough grinding where a considerable
amount of metal must be removed or when
obtaining a smooth finish is not important.
A Fine Grain Abrasive Grinding Wheel should be
used for sharpening tools or grinding to close size
tolerances because it removes metal more
gradually for precision grinding and achieves a
smoother finish.
7.1 Operating controls
Press on/off button on keypad (Figure 7-1) to start
or stop. Press any of the numbered buttons to start
machine at the designated speed. Press arrow
buttons to change rotation speed in 100 RPM
increments.
The digital readout displays RPM (revolutions per
minute), and will flash briefly during start up and
speed adjustments.
The grinder will automatically shut off after 10
minutes of inactivity.
When OFF button is pushed,
the wheels may take a few moments to
completely stop.
Note: After extended operation, the grinder housing
may be warm to the touch.
Figure 7-1: keypad
7.2 Precautions
1. Before starting the grinder, turn the wheels by
hand to verify that they are clear of obstructions
and turn freely. The tool rests and spark guards
should not touch the wheel.
2. Keep tool rests and spark guards to within 1/16"
of the grinding wheel.
3. Turn on the grinder and allow it to reach full
running speed before starting to grind.
4. Adjust the eye shields as needed.
5. Keep a steady, moderate pressure on the
workpiece and keep it moving at an even pace
for smooth grinding. Pressing too hard
overheats the motor and prematurely wears the
grinding wheels. Note the original bevel angle
on the item to be sharpened and try to maintain
the same shape. The grinding wheel should
rotate into the object being sharpened.
6. If grinding a narrow workpiece, slide it laterally
across the width of the wheel. Using the full
width of the wheel will help prevent a groove
forming at one place on the wheel.
7. Keep a water pot filled with water and dip your
work into it regularly to prevent overheating.
Overheating can weaken metals. Do not apply
water directly to the grinding wheels.
8. Do not use the side of the grinding wheel; this
puts dangerous stress on the wheel.

12
9. When the wheel becomes loaded or dull, use an
approved grinding wheel dresser and dress the
wheel face.
8.0 Adjustments
8.1 Eye shield tilt adjustment
1. Loosen lock knob (A1, Figure 8-1).
2. Adjust eye shield (A2) to the desired tilt angle.
3. Tighten lock knob.
Figure 8-1: eye shield adjustment
8.2 Spark guard
As the wheel wears down, the spark guards must be
re-adjusted to maintain a 1/16" distance.
Refer to Figure 8-1.
1. Loosen two hex cap screws (B1) with a 14mm
wrench.
2. Slide the spark guard (B2) to 1/16" distance from
the grinding wheel surface.
3. Tighten screws (B1).
8.3 Tool rest
As the wheel wears down, the tool rests must be re-
adjusted to maintain a 1/16" distance.
Refer to Figure 8-1.
1. Loosen two hex cap screws (C1) with a 14mm
wrench.
2. Slide the tool rest (C2) to a distance of 1/16"
from the grinding wheel.
3. Tighten screws (C1).
9.0 User-maintenance
For safety, turn the switch to OFF and remove plug
from the power source outlet before adjusting and
maintaining the bench grinder or buffer. If the power
cord is worn, cut or damaged in any way, have it
replaced immediately.
9.1 Ring test
Before replacing a grinding wheel, perform this
simple test on the replacement wheel:
1. Loop a piece of string through the grinding
wheel hole and suspend the wheel by holding
up the string.
2. Tap the wheel with a piece of scrap wood or a
wooden dowel.
3. A good wheel will "ring"; a defective wheel will
"thud". Discard any wheel that does not "ring".
An internal defect may not be apparent by visual
inspection alone. The ring test may identify an
internal crack or void.
9.2 Care of grinding wheels
In normal use, grinding wheels may become
cracked, grooved, rounded at the edges, chipped,
out of true or loaded with foreign material.
Cracked wheels should be replaced
IMMEDIATELY. The other conditions can be
remedied with a dressing tool. New wheels
sometimes require dressing to make them round.
See sect. 9.5.
9.3 Changing wheels
The JET IBG-8VS bench grinder comes equipped
with general purpose grinding wheels. Wheels vary
according to types of abrasive, hardness, grit size,
and structure. Contact your local distributor for the
proper grinding wheel or wire wheel brush for your
application.
If you replace a wheel, obtain one with a safe rated
speed at least as high as the NO LOAD RPM
marked on the grinder's nameplate. Table 2 shows
correct dimensions for the replacement wheel.
Model
Wheel
Diameter
Maximum
Width
Center
Hole
IBG-8VS
8"
1"
5/8"
Table 2
Your bench grinder will accept most polishing and
buffing wheels available at dealers and hardware
stores.
The use of any other accessory
is not recommended and may result in serious
injury!
To change a wheel (see Figure 9-1):
1. Disconnect grinder from power source.
2. Loosen spark guard (B) and tool rest (C) and
move them away from the wheel.
3. Remove wheel guard using a cross-point or
flathead screwdriver.

13
4. Stabilize wheel by holding opposite wheel
firmly, or placing a wood wedge between wheel
and tool rest.
Figure 9-1: wheel replacement
5. Unscrew arbor nut (D) with a wrench.
Note: Turn the nut on the right-hand wheel
counterclockwise to loosen. Turn the nut on the
left-hand wheel clockwise to loosen.
6. Remove outer flange (E), wheel (F), and inner
flange.
7. Clean flanges. Check the flanges to make sure
they are flat. Wheel flanges that are not flat will
cause the wheel to wobble.
8. Inspect the new grinding wheel and perform a
“ring test”. Do not install a damaged wheel.
9. Install inner flange, wheel (F), outer flange (E)
and nut (D) on the shaft. Tighten nut.
Do not overtighten nut;
this may cause the wheel to crack. Maximum
safe torque on nut is 20 lbf•ft (270 kgf•cm).
10. Reinstall guard cover. Adjust spark guards and
tool rests to 1/16" clearance from wheel.
9.4 Wheel balancing
With the grinder unplugged from the power
source, and arbor nuts snugged down, rotate
wheels by hand and observe their motion.
A grinding wheel has proper balance when:
1. The wheel’s outside face spins true and round;
that is, its circumference rotates concentric to
the arbor.
2. There is no side-to-side wobble.
The operator who takes time to patiently perform
needed adjustments will be rewarded by wheels
running true, and accurate grinding of work pieces.
9.4.1 Adjusting concentricity
If the outside face is not rotating concentric to arbor,
try shifting the wheel closer to arbor centerline
before tightening the nut.
Another method of achieving concentricity is the use
of a wheel dresser. “Dressing” is the removal of the
current layer of abrasive to expose a fresh surface.
A wheel dresser is also used to “true” a wheel; that
is, to make the grinding surface parallel to the tool
rest, so the entire wheel face presents an even
surface to the work piece. Proper use of a wheel
dresser will eliminate high spots and result in
concentric rotation about the arbor, as well as
minimize vibration. See sect. 9.5.
9.4.2 Correcting side-to-side wobble
The IBG-8VS Grinder has large, machined flanges,
making wobble unlikely if a good quality grinding
wheel is used. Should a wheel exhibit need for
adjustment:
1. Loosen nut and rotate the outer flange a little.
Snug the nut and spin the wheel by hand to
check.
2. If wobble still exists, continue repeating step 1,
rotating outer flange incrementally in the same
direction. See Figure 9-2. Make sure to keep
the wheel in the same position each time.
Figure 9-2: wheel balancing
3. If complete rotation of outer flange has proved
ineffective, remove nut, outer flange, and wheel
(keep wheel in same orientation by placing a
pencil mark on it somewhere for reference).
Then rotate inner flange about 90° and repeat
the above steps for the outer flange.
4. Continue this combination of flange movements
until the wobble is eliminated.
If required, a shim made of paper or card stock may
be placed between flange and wheel side.
NOTE: Very slight wobble may still exist at spin-up
and spin-down, but will not affect normal speed
operation.

14
9.5 Dressing the wheels
Below is a general procedure for dressing a grinding
wheel.
Use safety glasses or face
shield during dressing operations.
1. Back off the tool rest enough to allow the
dresser to hook over its inside edge (Figure 9-
3). Tighten tool rest in position.
2. Turn on grinder and allow it to reach operating
speed.
3. Set the wheel dresser on the rest and bring it
into contact with the wheel by raising its handle.
Hold the dresser firmly.
Note: If sparks appear, increase the pressure
of the dresser discs against the wheel.
4. Move the dresser evenly left and right across
the wheel face until the wheel looks clean and
is square to the tool rest.
5. Remove the dresser, and adjust the tool rest to
1/16” away from the newly dressed wheel.
Figure 9-3: wheel dressing
9.6 Wire wheel brushes
Wire brushing provides a fast way to remove rust
scale, burrs, and paint from metal. Use coarse wire
brushes for hard cleaning jobs. Use fine wire
brushes for polishing and finish work. When the
brush tips become dull, reverse the brush on the
grinder.
9.7 Cleaning
Metal shavings may still be hot
from recent grinding operations. Make sure
shavings and debris are cold before cleaning
the grinder.
Brush all shavings from the motor housing, tool
rests, and wheel guards. Check grinding wheels for
cracks and chips. Replace if damaged.
Avoid use of the following
cleaning chemicals or solvents: gasoline,
carbon tetrachloride, chlorinated solvents,
ammonia and household detergents containing
ammonia.
9.8 Lubrication
All motor bearings are permanently lubricated and
sealed at the factory and require no additional
lubrication.
9.9 Additional servicing
Any additional servicing on the grinder should be
performed by an authorized service representative.

15
10.0 Troubleshooting IBG-8VS Bench Grinder
10.1 General electrical and mechanical problems
Table 3
Symptom
Possible Cause
Correction *
Motor will not start.
Not connected to power source.
Verify that plug is properly inserted into
receptacle.
Motor cord cut or abraded.
Replace with new cord.
Wheels cannot rotate because of
obstruction.
Unplug and turn wheel by hand to ensure
free movement. Restart.
Plug on cord is faulty.
Replace with new plug.
Low line voltage.
Check power line for proper voltage.
Fuse blown or circuit breaker open.
Re-set. May be too many machines on
one line.
Faulty switch.
Replace switch.
Open circuit in motor or loose
connection.
Inspect all lead connections on motor for
loose or open connections.
Motor faulty, or inverter PCB fault.
Contact JET technical service.
Motor will not start;
fuses blow or circuit
breakers trip.
Too many electrical machines
running on same circuit.
Turn off other machines and try again.
Incorrect fuse.
Use time-delay fuse, or go to circuit with
higher rated fuse or breaker.
Wheels cannot rotate because of
obstruction.
Unplug and turn grinding wheel by hand to
ensure free movement. Clear any
obstructions and restart.
Undersized extension cord.
Use correct size extension cord.
Short circuit in line cord or plug.
Inspect cord or plug for damaged
insulation and shorted wires.
Short circuit in motor or loose
connections.
Inspect all connections on motor for loose
or shorted terminals or worn insulation.
Motor fails to develop
full power.
Low line voltage.
Check power line for proper voltage.
Faulty motor or capacitor
Contact JET technical service.
Motor overheats.
Motor overloaded.
Reduce pressure against wheel. Make
sure grit size is appropriate for the job.
Motor stalls, resulting
in blown fuses or
tripped circuit.
Motor overloaded.
Reduce load on motor; do not press so
hard.
Capacitor failure.
Contact JET technical service.
Short circuit in motor or loose
connections.
Inspect connections on motor for loose or
shorted terminals or worn insulation.
Low voltage.
Correct the low voltage conditions.
Incorrect fuses or circuit breakers in
power line.
Install correct fuses or breakers.

16
Symptom
Possible Cause
Correction *
Motor slows.
Motor overloaded.
Reduce load to motor; do not press so
hard.
Low line voltage.
Check power line for proper voltage.
Loose connections.
Inspect connections.
Frequent fuse or circuit
breaker failure.
Motor overload.
Reduce load to motor; do not press so
hard.
Electrical circuit overload; too many
electrical machines running on same
circuit.
Turn off other machines and try again.
Incorrect fuse or circuit breaker
Have electrician upgrade service to outlet.
Excessive vibration.
Wheel(s) out of balance; wobbling or
not rotating concentric to arbor.
Dress wheel or replace it. Adjust wobble
by rotating flange as needed.
Improper mounting.
Secure machine firmly to bench or stand.
10.2Digital readout error codes
Table 4
Message
Possible Cause
Correction *
OCL
Internal electronic overload has been tripped.
Do not overload motor; reduce pressure of
workpiece against wheels.
OH
IGBT protection activated.
Inspect wire connections to U/V/W for possible
short circuits. Verify that motor rating
corresponds to AC motor drive output power.
OE
Excessive input voltage (exceeds AC driver
limits).
Use correct voltage.
LE1
Low voltage; AC motor driver detects that DC
bus voltage has fallen below minimum
threshold
Make sure input voltage falls within range of AC
motor input voltage range. Check for abnormal
load in motor.
LP1
Low input voltage (below AC driver limits)
Use correct voltage.
* WARNING: Some corrections may required a qualified electrician.

17
11.0 Optional accessories
These accessory items, purchased separately, are available for your JET bench grinder or buffer.
Contact your dealer to order, or call JET at the phone number on the cover.
578172
578173
578100
IBG Stand
Deluxe IBG Stand
Flexible 3W LED Lamp
(includes two 1/4 x 3/8 mounting screws)
The following accessories are for using Grinder with the JET #414800 (JDCS-505) Dust Collection Stand:
414825 Reducer, 3 in. to 2.5 in.
414811 0.6M Hose, Heat Resistant, ø2.5 x 24.4 in.
12.0 Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-
274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of
your machine available when you call will allow us to serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Some parts are shown for reference only, and may not be available individually.

18
12.1.1 IBG-8VS Variable Speed Grinder –Exploded View

19
12.1.2 IBG-8VS Variable Speed Grinder –Parts List
Index No. Part No. Description Size Qty
1................IBG8-01..................... Truss Head Screw...................................................3/16”-24 x 1/4” ..............4
2................IBG8-02..................... Rubber Pad ............................................................. ......................................4
3................IBG8-03..................... Base Plate ............................................................... ......................................1
4................IBG8-04..................... Truss Head Screw...................................................3/16”-24 x 3/8” ..............4
5................F011289.................... Truss Head Phillips Tap Screw................................#8x1/2”..........................4
6................IBG8VS-06................ Electrical Box........................................................... ......................................1
7................IBG8VS-07................ Inverter PCB............................................................ ......................................1
8................TS-0050021 .............. Hex Cap Screw........................................................1/4”-20 x 5/8” ................8
9................TS-0720071 .............. Lock Washer............................................................1/4”................................8
10..............IBG8VS-10................ Base......................................................................... ......................................1
11..............IBG8-11..................... Cord Plate................................................................ ......................................1
12..............IBG8VS-12................ Control Panel w/ Digital Readout (includes #13)..... ......................................1
13..............IBG8VS-13................ Panel Decal ............................................................. ......................................1
14..............IBG8VS-14................ Motor Housing ......................................................... ......................................1
15..............IBG8VS-15................ Stator....................................................................... ......................................1
16..............IBG8VS-16................ Rotor........................................................................ ......................................1
17..............IBG8-17..................... Motor Fan ................................................................ ......................................1
18..............BB-6204ZZ................ Ball Bearing .............................................................6204ZZ .........................2
19..............IBG8-19..................... End Bell................................................................... ......................................2
20..............TS-1540031 .............. Hex Nut....................................................................M5.................................4
21..............IBG8-21..................... Wheel Guard............................................................ ......................................2
22..............IBG8-22..................... Wheel Flange........................................................... ......................................4
23..............IBG8-23..................... Grinding Wheel .......................................................#36 Grit, 8” Dia .............1
24..............IBG8-24..................... Hex Nut (Left Hand Thread) ....................................5/8”................................1
25..............IBG8-25..................... Wheel Cover............................................................ ......................................2
26..............IBG8-26..................... Truss Head Screw...................................................1/4”-20 x 3/4” ..............10
27..............IBG8-27..................... Tool Rest-Left.......................................................... ......................................1
28..............TS-0680041 .............. Flat Washer .............................................................3/8”................................4
29..............IBG8-29..................... Hex Cap Screw........................................................3/8”-16 x 3/4” ................4
30..............IBG8-30..................... Tool Rest-Right........................................................ ......................................1
31..............TS-0060011 .............. Hex Cap Screw........................................................3/8”-16 x 1/2” ................4
32..............IBG8-32..................... Spark Guard –Left .................................................. ......................................1
33..............IBG8-33..................... Eye Shield ............................................................... ......................................1
34..............IBG8-34..................... Eye Shield Bracket -Left.......................................... ......................................1
35..............IBG8-35..................... Eye Shield Plate ...................................................... ......................................1
36..............IBG8-36..................... Truss Head Screw...................................................3/16”-24 x 1/2” ..............2
37..............IBG8-37..................... Knob ........................................................................ ......................................1
38..............TS-0680021 .............. Flat Washer .............................................................1/4”................................1
39..............IBG8-39..................... Spark Guard –Right................................................ ......................................1
40..............IBG8-40..................... Eye Shield Bracket –Right...................................... ......................................1
41..............TS-2284082 .............. Pan Head Screw......................................................M4 x 8...........................4
42..............IBG8-42..................... Screw.......................................................................M5 x 0.8 x 205 ..............4
43..............IBG8-43..................... Grinder Wheel..........................................................#60 Grit, 8” Dia .............1
44..............IBG8-44..................... Hex Nut (Right Hand Thread)..................................5/8”................................1
45..............IBG8-45B .................. Dust Port Assembly................................................. ......................................1
45-1...........IBG8-45-1.................. T Fitting.................................................................... ......................................1
45-2...........IBG8-45-2.................. Spring ...................................................................... ......................................2
45-3...........IBG8-45-3.................. Connector Sleeve.................................................... ......................................2
46..............IBG8-46E .................. Power Cord with Plug..............................................1.0mm²x 3G.................1
47..............IBG8-47..................... Strain Relief............................................................. ......................................1
50..............IBG8-50..................... Lamp Fixed Bracket................................................. ......................................1
51..............F000296.................... Flat Hd Phillips Machine Screw...............................1/4”-20 x 3/8”................2
53..............TS-0680041 .............. Flat Washer .............................................................3/8”................................2
54..............IBG8-54..................... Dresser Assembly....................................................Dia. 1-1/4 ......................1
54-1...........IBG8-54-1.................. Body......................................................................... ......................................1
54-2...........IBG8-54-2.................. Hood........................................................................ ......................................1
54-3...........IBG8-54-3.................. Cutter....................................................................... ......................................4
54-4...........IBG8-54-4.................. Cutter Washer.......................................................... ......................................2
54-5...........IBG8-54-5.................. Pin............................................................................6mm..............................1
54-6...........TS-1503051 .............. Socket Head Cap Screw .........................................M6 x 20.........................1

20
Index No Part No Description Size Qty
54-7...........IBG8-54-7.................. Square Nut ..............................................................M6.................................1
55..............TS-0680041 .............. Flat Washer .............................................................3/8”................................2
56..............TS-0060011 .............. Hex Cap Screw........................................................3/8”-16 x 1/2” ................2
57..............IBG8-33..................... Eye Shield ............................................................... ......................................1
58..............IBG8-35..................... Eye Shield Plate ...................................................... ......................................1
59..............IBG8-36..................... Truss Head Screw...................................................3/16”-24 x 1/2” ..............2
60..............IBG8-37..................... Knob ........................................................................ ......................................1
61..............TS-0680021 .............. Flat Washer .............................................................1/4”................................1
100............IBG8-100................... Eye Shield Assembly –Left (includes 31-38,53)..... ......................................1
101............IBG8-101................... Eye Shield Assembly –Right (includes 39,40,55-61) ....................................1
..................JET-92-73R............... JET Logo (not shown) .............................................92x38mm......................1