Jiangsu GoodWe EzLogger User manual






UserManual
EzLogger
Ver03





















TableofContents
1、Symbols .................................. 01
2、Safety..................................... 02
3、Installation............................... 03
3.1Unpacking ............................. 03
3.2AppearanceandSize......................04
3.3EquipmentInstallation ....................04
3.4ElectricalConnection......................06
4、IndicatorLights..............................20
5、OperationwithRippleControlReceiver(RCR)....21
5.1ConnectionwithRCR......................21
5.2OperationwithRCR.......................22
6、ResetandReload..... .... .... ............23
7、OperatewithEzExplorer .....................24
7.1NewEzLogger............................24
7.2EditEzLogger.............................27
7.3DeleteEzLogger..........................29
7.4MemoryStatus...........................31
7.5ViewProperty............................33
7.6Summary................................35
7.7SetdateCollectPeriod.....................37
8、TechnicalParameters ........................40
8.1OperationConditions......................40
8.2OperationLimitation......................40
8.3DataStorage.............................41
9、Certificates................................41
10、Warranty..................................42
10.1WarrantyPeriod........................42

10.2WarrantyCard..........................42
10.3WarrantyConditions....................42
10.4ScopeofWarranty......................43
11、Contact..................................44

1
1、Symbols


Caution!‐Failuretoobserveawarningindicated
inthismanualmayresultinjury.

Productshouldnotbedisposedashousehold
waste.

Thissideup;thepackagemustalwaysbe
transported,handledandstoredinsuchaway
thatthearrowsalwayspointupwards.

Componentsoftheproductcanberecycled.

Fragile;thepackage/productshouldbehandled
carefullyandneverbetippedoverorslung.

Keepdry;thepackage/productmustbeprotected
fromexcessivehumidityandmustbestored
undercover.
CEMark

2
2、Safety

TheEzLoggerofJiangsuGoodWePowerSupply
TechnologyCo.Ltd.(hereinafterreferredtoasGoodWe)
strictlyconformstorelatedsafetyrulesindesignandtest.
Safetyregulationsrelevanttothelocationshallbe
followedduringinstallation,commissioning,operation
andmaintenance.Improperoperationmaycauseserious
injury,electricshockand/ordamagetoequipmentand
property.
EnsurechildrenarekeptawayfromEzLogger.
DonotopenthefrontcoveroftheEzLogger.Apartfrom
performingworkatthewiringterminal(asinstructedin
thismanual),touchingorchangingcomponents
withoutauthorizationmaycauseinjurytopeople,
damagetoEzLoggerandannulmentofthewarranty.
Staticelectricitymaydamageelectroniccomponents.
Appropriatemethodsmustbeadoptedtopreventsuch
damagetotheEzLogger;otherwisetheEzLoggermay
bedamagedandthewarrantyannulled.


3
3、Installation
3.1Unpacking
WhenyoureceivetheGoodWeEzLogger,pleasecheckfor
externaldamagetotheEzLoggerandanyaccessories.Please
alsocheckthatthefollowingsareincluded:
EzLogger.............1PowerAdapter............1
MicroSDCard........1FixingBracket.............2
ScrewM3*8..........4MiniUSBCable............1
UserManual.........1WarrantyCard.............1
FlashDisk............1Connector.................1
EzLogger
Power
Adapter

Fixing
Bracket

Screw
M3*8
MiniUSB
Cable

MicroSD
Card
User
Manual
Warranty
Card
FlashDisk

Connector


4
3.2AppearanceandSize



Figure3.2.1

3.3EquipmentInstallation
3.3.1Selectingtheinstallationposition
Thefollowingmustbeconsideredwhenselectingthebest
locationforanEzLogger:
Indooruseonly.
Themountandinstallationmethodmustbesuitableforthe
EzLogger'sweightanddimensions.
Thelocationmustbewellventilatedandshelteredfrom
directsunlight.

L=146.0
W=103
H=31.2

5
3.3.2MountingProcedure
Figure3.3.2‐1
Figure3.3.2‐2







Figure3.3.2‐3Sizeofinstallationplate
Step1：Assemble
EzLoggerandFixing
Bracketasshowninthe
Graph3.3.2‐1,and
tightenthembyScrews
M3*8intheaccessory
bag.
Step2：Tighten
EzLoggerbyScrews
φ4*12.Installation
dimensionsareshown
intheGraph3.3.2‐2.

6
3.4ElectricalConnection
3.4.1InterfaceInstruction


ABCDEF
Figure3.4.1
AAdapterSocket
BRS485RJ45Socket(connectstoinverter)
CUSBportSocket
D6pinTerminalSocket,RefertoTable3.3
ELANRJ45Socket(connectstonetwork)
FMicroSDCardSocket
Table3.4.1
Notice:UnpackthemicroSDcardandinsertittothesocket(F)

PleasedonotmixinterfaceBandEup
whichwillleadtodamagetoEzLogger!



7
3.4.2InstallationProcedure
Step1:Firstofall,makeupcables
NOTICE:Inordertoimplementwaterproof,thecablesshould
bemadeupbyhandstrictlyobeytheguidanceinmanualof
inverter.
ThelinesequenceofbothplugsofRS485cableshouldbemade
upsameasshowninFig3.4.2.1.

Fig3.4.2.1Linesequence
ThelinesequenceinbothRJ45plugsshouldobeyTIA/EIA‐568B
criterionstrictly,from1to8asbelow:



8
LineColorLineColor
1Orange&White 5Blue&White
2Orange6Green
3Green&White7Brown&White
4Blue8Brown
Besidesthat,eachcableshouldbetestedbyLANcabletesterto
ensurethecableisOK.Thesecableswillbeusedtoconnectnot
onlyEzLoggerandinverterbutalsoinverterandinverter.
Step2:Checkthecabledaisychain
Thewholesystemshouldbemadeupasshowninbelow
Fig3.4.2.2,inwhichthelaptopisonlyusedfordebug.

Fig3.4.2.2.Wholesystemconnectiondiagram
Beforecompletethewholeconnection,itshouldbetestedas
below:
Testtheconnectionfromplug1atoplug(N+1)basshownin

9
Fig3.4.2.3.Ifeverythingisok,theLANcabletesterwilltellthe
line3/6/7/8 isOK.Neglectthestatusofline1/2/4/5 becausethe
line1isshortedtoline2andline4isshortedtoline5ininverter.

Fig3.4.2.3.CheckthewholeRS485cableconnection
Iftheline3/6/7/8 isnotok,pleasepullouttheplugNbfrom
inverterN#,andtesttheconnectionfromplug1atoplugNb,as
showninFig3.4.2.4.

Fig3.4.2.4.Checktheconnectionbetween1aandNb
Ifthetestresultisok,itmeansthereissomethingwrongwith
inverterN#.Firstre‐checkcableN+1usingLANcabletesterand
makesureitisOKandinserttheplugbackintoinverterN#.
TheninsertplugNbintoinverterN#,andpulloutplugNafrom
inverter(N‐1)#asshowninFig3.4.2.5.Checkandmakesurethe
connectionofplugsandsocketsisfirmlygood.Thentestthe

10
connectionbetweenplugNaandplug(N+1)b.Iftheconnection
isOK,insertplugNaintoinverter(N‐1)#.Thenre‐test
connectionfromplug1atoplug(N+1)bandtheresultwillpass.

Fig3.4.2.5.ChecktheconnectionbetweenNaand(N+1)b
Repeatstepsabovecanfindthebugandthenfixitonebyone
untilthewholedaisychainconnectionisok.
AtlastpulloutcableN+1frominverterN#andfastenthecover
andtheninsertplug1atoEzLogger.
Step3:PowerontheEzLoggerandallinverters.Observethe
statusofLEDindicatorsontopcoverofEzLogger.
IfeverythingisOK,itshouldbelikebelow:
PowerLed:alwayson
Ifnot,checkthepowersupplyadaptorofEzLogger.
SpeedLed:alwaysonaftertheLANcableisconnectedtothe
Ethernetnetwork
LinkLed:flashfrequentlyaftertheLANcableisconnectedto
theEthernetnetwork

11
Ifnot,checktheconnectionbetweenEzLoggerandexchanger
orrouter.
RS485Led:flashevery1minute
Ifnot,itmeansthecommunicationbetweenEzLoggerand
invertersisnotOK.Weneedtore‐checktheconnectionofthe
cabledaisychainandconfirmtheprotocol.

3.4.3ConfigureEzLogger
AlaptopwithEthernetsocketisessentialforEzLogger
configuration.
Step1.PowertheEzLoggeronwithpoweradaptor
Step2.UsingaCAT5LANcableconnectthelaptopwith
EzLoggerdirectly.ModifytheIPaddressofthelaptopto
192.168.1.100followingstepsbelow.

Fig3.4.3.1.ClickStart,andclick‘ControlPanel’
Youwillget:

12

Fig3.4.3.2.Click‘Viewnetworkstatusandtasks’
Youwillget:

Fig3.4.3.3.Click‘LocalAreaConnection’
Youwillget:

13
 
Fig3.4.3.4.click‘Properties’button
Youwillget:

14
 
Fig3.4.3.5.Choose‘InternetProtocol’andclick‘Properties’

15

Fig3.4.3.6.Choose‘UsethefollowingIPaddress’andkeythe
digitalinpurplecircleasaboveandclick‘OK’button

Step4.RunEzConfig.exethatisstoredintheflashdisk.
Ifthe‘ConnectionStatus’is‘ConnectFail’,pleasechecktheIP
addressofyourlaptopis192.168.1.100ornot.

16

Step4.1TimeConfiguration
OnceEzConfig.execonnectswithEzLoggersuccessfully,itwill
setthesystemtimeofthelaptoptoEzLoggerautomatically.If
thereistimedifferencefromlocaltime,youcanclick‘SetTime’
buttontosettime.
Step4.2InverterInformation

Fig3.4.3.7.InverterList
Afterconnects,youcanclick‘Refresh’buttontoacquirethe

17
inverterlistwhicharecommunicatingwithEzLoggerwell.
Onlywheneachinverterinstalledinthewholesystemisonline
canwefinishthedebugprocess.
Step4.3LANParameterConfiguration
TherearetwowaysforEzLoggertobeallocatedIPaddress.One
isstaticIPaddressandtheotheroneisautomatically.
Click'DHCPEnable'toenableDHCPfunctionwhichmeansthe
IPaddressofEzLoggerwillbeallocatedfromrouterorswitch
automatically.

Fig3.4.3.8
HoweverifitispreferredtouseastaticIPaddressforEzLogger,
pleasetypethecorrectIP,SubnetMaskandGateway,andthen
click'Set'buttonandtheLANconfigurationwillbeappliedto
EzLogger
NOTICE:
OnceLANparameterismodified,theconnectionbetween
EzLoggerandEzConfigwillbreak.Ifitisneededtoconnect
EzConfigwithEzLoggeragain,youhavetoreloadEzLoggerto