Jinan Lifan Machinery PHILICAM User manual

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
1
PHILICAM
PHILICAM
Plasma cutting machine user manual
Jinan Lifan Machinery Co.,Ltd
Website:www.fldcnc.com
http://fldcnc.en.alibaba.com
Service Contact information :
Email: [e-mail]
Service Skype: lifancnc
Please send us your Order No. , we will do our best service for you.

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
2
Customer First Service First Quality First
Plasma cutting machine install manual
CONTENTS
1. Install machine ………………………………………..page2
2. Adjusting ……………………………………………… page8
3. Maintenance…………………………………….………page13
4. Other point need pay attention………………………….page18

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
3
Chapter One: Install Machine
Thank you very much for your right choice .
Safety
Plasma Cutting Machine are designed and built with ample safety
consideration. However, proper installing and operating the machine can
increase your safety.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT CASUALLY
WITHOUT READING THIS MANUAL THROUGHOUT.
Attention:
*Before connect all the lines,please check all the switches in Power off position
*Please check there is connector for 380V and 220V in your place.
1.Put machine in a suitable position

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
4
2.Connect lines in the control box
Photo 1.-Machine electric parts connecting
input three phase 380v and
one zero wire,blue wire is
N zero wire ,three black
wire is L fire wire .
Connect the plasma
power ,three phase 380v

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
5
Photo 2.—Plasma Power connect
Adjust current
Check air
Cutting
Arc line
Material holder
connector
Sign line
Plasma head
connector

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
6
Photo 3- Material holder
Attention:
* Ground function.Must touch with material when working
* This holder can put any place of the material.
* During working process , Do Not touch this holder.
Material holder
This is holder
for material
Air compressor
Air compressor
380v

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
7
Photo 4—Air compressor power connect
Photo 5-Air compressor connector with plasma power
Exhaust pressure
at least 0.8MPa
Air compressor connect
with plasma power

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
8
Photo 6- Air compressor connect with plasma power
Connect the air
compressor

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
9
Photo 7 -- Open green button
Operating panel
Power swith
Emergency stop

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
10
Photo 8 -- Operating system
Attention:
If screen show is not English , you can press G G 3 , screen will show as follow ,you
choose English , it will be ok.
Main menu
U disk,upload
the file

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
11
Photo 9-- change English show
3. Set up the parameter
Press system

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
12

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
13
Chapter 2 Adjusting
During work, there need adjust according different material.
First step :Adjusting Air Pressure

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
14
Photo 10. Air pressure adjusting
Attention:
* Need pull button up then adjusting. When finish, please put down this button.
* High thickness material need higher air pressure
40--63A : air pressure :0.3---0.6MPa
100--200A: air pressure :0.5--0.7Mpa
Step 1.open Plasma power
Step 2.Press the button into Check Air(Photo 11th)
Air pressure adjusting
Air pressure normal
0.3--0.6MPa

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
15
Step 3.Adjusting Air pressure on 0.5Mpa
Step 4. Press the button into Cutting (Photo 11)and start to work
Photo 11--Current Adjusting
Second Step: Adjusting Current according to different
Photo 12--Current Adjusting ( See attachment suggestion)
Attention:
*Adjusting current when working according to material.
Current adjusting
by this button

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
16
*Data setting is on the basic of material thickness
Operation:
After adjusting, now let’s start to operate.
1.move plasma head to left bottom of working piece
Press X+ X- Y+ Y- ,move the x axis and y axis left bottom of
working piece .as picture Photo 13
Photo 13
2.upload the file , plug the U disk , press EDIT on the screen ,then press
USB, again press input ,find U disk file , press direction button find file
which you need cut , then press ENTER button .then press ESC ,choose
AUTO ,press Fbutton ,set up working speed .then press green
button ,machine start to work.
Left bottom

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
17
Edit
USB
File
Input
ENTER

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
18
3. Adjust torch height :
This is height value,
1-3mm about set 90,
100mm about set 105.
Long time press
this button
Show this
F button
Change
working speed
Torch height up
Torch height down
Start button

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
19
Chapter 3 Maintenance
Change the Electrode
Pull down the head of water pipe from plasma head
*From Left direction to Right side
Then press this button
Two times
Last press this
button

济南力帆机械设备有限公司
Jinan Lifan Machinery Co.,Ltd
20
Loosen small electrode by spanner then put it out by hand.
*Direction same as Big electrode.
Other point need pay attention：
1. Put material flat before working
2. Cleaning Rail and insert oil before work off
3. Power off when change Nozzle and electrode
4. Fulfill water into water pump during work process
5. Adopt Pure water to keep electromagnetic valve in long life time
6. Check water pump in working process (Water out) before working.
Loose small electrode
by spanner
Loosen Big electrode
by spanner