JK Audio AutoHybrid IP2 User manual

JK Audio
User Guide
AutoHybrid IP2™
VoIP/AoIP Codec

ii AutoHybrid IP2™ VoIP/AoIP Codec
Thank You
Thank you for purchasing a JK Audio AutoHybrid IP2 VoIP/AoIP Codec. Please
read this guide for instructions on setting up and using your new product.
Getting Assistance
If you have technical or application questions:
In the US & Canada, call us toll free at: 800-552-8346
All other countries dial: 815-786-2929 (M-F 8:30-5:00pm Central Time Zone)
Email us at: [email protected]
Or, check out our FAQ section for answers to common questions.
Limited Warranty
The AutoHybrid IP2 is covered by a 2 year warranty to be free from defective
workmanship and materials. To obtain service, contact JK Audio by phone or
email for return authorization. Once authorized, you will carefully pack and ship
the faulty product and all accessories to us. You will pay for shipping to us and
we will pay for return back to you.
This warranty does not cover damages due to accident, weather, re, ood,
earthquake, misuse, unauthorized repairs or modications, or damages occurred
in shipping, only defective workmanship or materials.
There are no expressed or implied warranties which extend beyond the
warranty here made.
Welcome

Contents
Overview 1
Getting to know your AutoHybrid IP2
2Controls & Indicators
3Inputs & Outputs
2
Getting Connected 4
Logging In 5
Graphic User Interface
6
7
8
11
12
13
Call Management
Accounts
Audio
Network
System / Management
FAQs 14
Troubleshooting 15
Block Diagram 16
Technical Information 17
FCC Compliance Notice 18
Contents iii
Contents

iv AutoHybrid IP2™ VoIP/AoIP Codec
Features
Simple 2-Line VoIP Call Control,
Auto-Answer, and Conference
Caller ID
G.711, G.722 (HD Voice) VoIP Hybrid
24-bit AoIP Wide Band Stereo Codec
AGC & Ducking
Send and Receive LED Metering
Female XLR Line Input (2)
Male XLR Line Output (2)
LAN, USB, Remote Control
Connections
Rear Panel Recessed Level Controls
Remote Control I/O Terminal Block
PoE or AC Mains Powered
Optional RA2 Rack Mount Adapter
Features
PS009 Power Supply
CN094 AC cable
CN114 Ethernet cable
CN115 USB cable
What’s in the Box?

Overview 1
Introducing the AutoHybrid IP2™
AutoHybrid IP2™ functions as a two-line VoIP hybrid. The desktop/half-rack
design provides one button access to the common features of a phone line
hybrid including: call control, auto-answer, and conference. Advanced call control
features and VoIP line setup are provided through the internal web server. In
VoIP mode, Line-level XLR jacks provide mono send and receive audio for Line 1
and Line 2.
The AutoHybrid IP2™ Remote jack allows easy connection to the JK Audio
Interchange™ Intercom Phone Bridge, offering an auto-answer VoIP connection
into your party-line intercom.
Low power consumption for Power over Ethernet (PoE) applications. External
power supply included for LAN connections without PoE capability.
Ready to go?
The AutoHybrid IP2 controls and connectors are clearly marked and ready for
operation. If this is your rst exposure to a hybrid, we suggest that you read the
entire manual to allow you to take advantage of all these features.
Any Questions?
Before you pick up the phone... Please thumb through the rest of this manual.
You might nd those deep technical questions are covered on later pages.
Overview
Product Registration / Firmware Updates
Your AutoHybrid IP2 contains many advanced features, but we are constantly
looking for ways to improve. Product Registration allows us to keep you informed
of any rmware updates that become available in the future.
Please register your purchase by visiting:
http://www.jkaudio.com/support/
STOP

2AutoHybrid IP2™ VoIP/AoIP Codec
Getting to Know Your AutoHybrid IP2
4 5 621 3 7 8
1. Hidden Reset Switch
Use a paper clip to reset the AutoHybrid IP2 instead of power cycling.
2. Auto Answer
When enabled, AutoHybrid IP2 automatically answers an incoming call and
then disconnects after the caller hangs up.
3. OH LED
Lit when the corresponding line is off-hook. For incoming calls, the OH
LEDs provide a visual ring indication.
4. Call Buttons
Press this button to answer the corresponding line.
5. Drop Buttons
Press this button to drop a call or place the corresponding line on-hook.
6. Signal LEDs
Send LEDs represent the signal level going into the transmitter. Receive
LEDs represent the signal level at the output XLR.
7. Conference Button
Conference lines 1 & 2 together when both lines are off-hook. The LED will
only light up when there are two calls in an active conference.
8. Power LED
Lit when unit receives power from AC or PoE.
Controls & Indicators
4 56 3 2
Line 2
Line 1

3
Getting to Know Your AutoHybrid IP2
5 6 71 2 3 4
8 9
Inputs & Outputs
1. Line Out 2/R
Line 2 or Stereo Right Channel male balanced XLR output with recessed
level control.
2. Line In 2/R
Line 2 or Stereo Right Channel female balanced XLR input with recessed
level control.
3. Line Out 1/L
Line 1 or Stereo Left Channel male balanced XLR output with recessed
level control.
4. Line In 1/L
Line 1 or Stereo Left Channel female balanced XLR input with recessed
level control.
5. LAN Jack
The LAN jack has a Link/Activity LED and 10/100 Mbps speed LED.
6. Remote Jack (For JK Audio products only)
WARNING! Connecting this jack to any device besides a JK Audio
product may result in irreparable damage. This damage is not covered
under warranty.
7. Remote Header
The removable screw terminal block provides connection to switch contacts
for remote operation. See page 17 for the Remote Header Pinout.
8. USB Jack
Connecting the USB port to a computer is not necessary for typical
operation. The USB port should only be used by your IT administrator to
obtain the IP address or perform a “check le system” command.
9. Power Jack
For connection only to the supplied 9VDC regulated power supply.
Inputs & Outputs

4AutoHybrid IP2™ VoIP/AoIP Codec
Getting Connected
Setting Up
Although each application will require a slightly different setup, following is a
general cable connection setup and explanation.
1. Connect the supplied ethernet cable between the jack marked <LAN> and
an active ethernet port.
2. Connect to your mixer.
i. Connect a line-level audio signal to the AutoHybrid IP2 <Line In> jack(s).
ii. Connect the <Line Out> jack(s) to the line-level input(s) on your
mixing console.
3. Connect the supplied AC power cord to the back of the AutoHybrid and then
to an AC power outlet. Or, enable Power over Ethernet (PoE) on your switch
or router.
Your AutoHybrid IP2 will be ready to take calls once a SIP Account is congured.
What is SIP?
Session Initiation Protocol.
It is a standard communications protocol used for controlling multimedia
communication sessions. For public service outside of your local network, users
must register with a VoIP provider which provides a directory service similar to a
public switched telephone network for POTS lines.
The AutoHybrid IP2 protocol stack provides the components necessary to
provide a standardized method for managing the device, providing real-time
multimedia transport and monitoring and controlling the Quality of Service.
SIP is a standard mechanism for connection management, including registration
and location service, that provides phone number portability across the internet.

Logging In 5
Logging In
Before Logging In
To log into the AH IP2 GUI you will have to enter the IP address in your browser's
address bar. There are a few methods of nding a dynamic IP address. You
must be on the same network as the AutoHybrid IP2.
A. Windows PCs running Vista or later: Open Windows Explorer and
navigate to Network. Users can connect by simply clicking on the icon
representing the AutoHybrid IP2.
B. Windows / Mac / Linux: Log into the router connected to the Autohybrid to
view the the IP address of connected devices.
1. Enter the Router's IP address into the address bar of your internet
browser to access the router's control panel. The IP address can be found
on the base of the router or in the router's manual.
2. Enter a username/password when prompted. If they have not been
changed from the default, the router login credentials can be found in the
router's documentation.
3. The AutoHybrid IP2 will be displayed in the router's connected devices list
with a hostname of AutoHybrid-IP2.
C. Use an IP address scanning application.
Tip: For easy identication, disconnect unused devices from the network and
connect only one AutoHybrid at a time. The MAC address can be found on the
bottom of your AutoHybrid IP2 but we recommend labeling the device with the
IP address or the Account Name registered to the device.
Logging In
Enter the AutoHybrid IP2's IP address in the address bar in your browser to
access the AH IP2 GUI.
Default Username: admin
Default Password: admin
See Page 9 to change username and password.
Username:
Password:

6AutoHybrid IP2™ VoIP/AoIP Codec
Graphic User Interface
3 4 5 6 87
1
13 14
9 10 11 12
2
Note: Controls & Indicators 2-12 only apply to the corresponding line.
Gray = OffBlue = On