Johnson Controls M300MJ-4-20 User manual

M300MJ-4-20
4-20mA Analog Input Module
BEFORE INSTALLING
This information is included as a quick reference installation guide. Refer to
the control panel installation manual for detailed system information. If the
modules will be installed in an existing operational system, inform the opera-
tor and local authority that the system will be temporarily out of service. Dis-
connect power to the control panel before installing the modules.
NOTICE: This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The M300MJ-4-20 4-20mA Analog Input Module is intended for use in in-
telligent, two-wire systems, where the individual address of each module is
selected using the built-in rotary switches. This module allows intelligent pan-
els to interface and monitor two-wire or three-wire sensors, that produce a
4-20mA signal output. It transmits the status (normal, open, or alarm) of one
sensor back to the control panel. The M300MJ-4-20 has a panel controlled
LED indicator. Only one sensor can be connected to the M300MJ-4-20.
COMPATIBILITY REQUIREMENTS
To ensure proper operation, this module shall be connected to a compati-
ble Johnson Controls system control panel only (list available from Johnson
Controls). In addition, please refer to Johnson Controls Device Compatibility
document for the list of compatible devices.
FIGURE 1. CONTROLS AND INDICATORS:
C0218-05
SPECIFICATIONS
SLC
Normal Operating Voltage: 15 to 32 VDC
Maximum Current Draw: 9.3 mA (LED on)
Average Operating Current: 1 mA (LED flashing)
External Supply
Normal Operating Voltage: 24 VDC Nominal
Standby Current: 10 mA
Maximum Current: 510 mA
Initiating Device
Maximum Current: 500 mA
Temperature Range: –10°C to 60°C
Humidity: 10% to 95% Non-condensing
Dimensions: 41/2˝ H × 4˝ W × 1
1/4˝ D (Mounts to a 4˝ square by 21/8˝ deep box.)
Accessories: SMB500 Electrical Box
JC-460-007 1 I56-3369-001
I56-3369-001
INSTALLATION AND MAINTENANCE INSTRUCTIONS
MOUNTING
The M300MJ-4-20 mounts directly to 4-inch square electrical boxes (see Fig-
ure 2). The box must have a minimum depth of 21/8inches. Surface mounted
electrical boxes (SMB500) are available from Johnson Controls.
FIGURE 2. MODULE MOUNTING:
C0449-01
WIRING
NOTE: All wiring must conform to applicable local codes, ordinances, and
regulations. This module is intended for powerlimited wiring only.
1. Install module wiring in accordance with the job drawings and appropri-
ate wiring diagrams.
2. Set the address on the module per job drawings.
3. Secure module to electrical box (supplied by installer), Figure 2.
507 E. Michigan Street
Milwaukee, WI 53201
Phone: [phone]

JC-460-007 2 I56-3369-001
©2008 Johnson Controls
Figure 3. 4-20mA Module 3-wire Configuration:
(+)
(–)
(+)
(–)
(+)
(–)
TERMINAL WIRING MUST
BE POWER LIMITED.
TO NEXT
DEVICE
M300MJ-4-20
MODULE SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
CONNECT MODULES TO LISTED
COMPATIBLE CONTROL PANELS ONLY.
FROM PANEL
OR PREVIOUS
DEVICE
SLC WIRING
( - )
SENSE
( + )
{
TO 4-20mA
3-WIRE
DEVICE
DO NOT LOOP WIRE UNDER
TERMINALS. BREAK ALL WIRE
RUNS TO PROVIDE SUPERVISION
OF CONNECTIONS.
24 VDC POWER
LIMITED
( + ) ( - )
24 VDC POWER
SUPPLY ISOLATED,
REGULATED, POWER
LIMITED.
TO NEXT
MODULE
C0994-03
Figure 4. 4-20mA Module 2-wire Configuration:
(+)
(–)
(+)
(–)
(+)
(–)
TERMINAL WIRING MUST BE
POWER LIMITED.
DO NOT LOOP WIRE UNDER
TERMINALS. BREAK ALL WIRE
RUNS TO PROVIDE SUPERVISION
OF CONNECTIONS.
M300MJ-4-20
MODULE
TO NEXT
DEVICE
SIGNAL LINE CIRCUIT (SLC)
32 VDC MAX.
TWISTED PAIR
IS RECOMMENDED
CONNECT MODULES TO LISTED
COMPATIBLE CONTROL PANELS ONLY.
FROM PANEL
OR PREVIOUS
DEVICE
SLC WIRING
24 VDC POWER
LIMITED
( + ) ( - )
( – ) SENSE
( + )
{
TO 4-20mA
2-WIRE DEVICE
24 VDC POWER SUPPLY
ISOLATED, REGULATED,
POWER LIMITED.
TO NEXT
MODULE
C0995-03