Joy MagConnect User manual

Seat Bolt | Bolt Mount
There are four different mounting options that can be
utilized for securing the mount to a vehicle bolt. There
are a few things to consider when choosing the best
location for the bolt mount. When possible the arm at the
base of the mount should run perpendicular to the
vehicle floor. This provides ultimate support of the
mount. Included are three bolt brackets along with a
base that should be utilized to accomplish this.
Choose the best option based on the hardware in the
vehicle while ensuring configuration provides optimal
mount stability.
Flat Horizontal Surface: Follow
Mounting Option 1 on page 2.
Flat Vertical Surface: Follow Mount-
ing Option 3 on page 3.
Flat Horizontal Surface Obstructed
Bolt: Follow Mounting Option 2 on
page 2.
Choose a location
(a) 90º raiser bracket x1
(b) 90º bracket x1
(c) 180º bracket x1
(d) support bracket x1
(e) washer x1
(f) screw x1
(a)
(e)
(i) (j)
(f)
(g) (h)
(b) (c)
(d)
Package Contents:
(g) screw nuts x2
(h) support foot x1
(i) support foot cap x1
(j) base x1
Angeled Surface: Follow Mounting
Option 4 on page 3.
1
INSTALLATION GUIDE MagConnect HD Seat Bolt | Bolt Mount
™
Support
For questions or concerns please contact us at:
Customer Service Support
Toll Free: +1.877.JOY.FACT (877.569.3228)
[e-mail]

Secure Base Using Vehicle Bolt: Replace bolt while
securing the base (j).
Attach Mount to Base: Place mount over base and
secure by turning latch.
Attach Bracket with Bolt & Mount to Base: Replace
the bolt while securing the bracket. Place mount over
base and secure by turning latch.
(j)
(i)
(g)
(h)
(d)
Remove Vehicle Bolt: Remove the bolt from the vehicle.
Mounting Option 1
Secure Base to 180º Bracket: Assemble bracket
according to diagram above. The extended bracket (d, i,
g, h) can be utilized to add additional support. Ensure
connection is tight.
(e)
(j)
(f)
(g)
(c)
Mounting Option 2
Remove Vehicle Bolt: Remove the bolt from the vehicle.
2
MOUNT INSTALLATION: Mount

Secure Base & Support Bracket to 90º Bracket:
Assemble bracket according to diagram above. The
extended bracket (d, i, g, h) can be utilized to add
additional support. Ensure connection is tight.
(i)
(h)
(e)
(j)
(f)
(g)
(b)
(d)
Mounting Option 3
Remove Vehicle Bolt: Remove the bolt from the vehicle.
Remove Vehicle Bolt: Remove the bolt from the vehicle. Attach Bracket with Bolt & Attach Mount to Base:
Replace the bolt while securing the bracket. Place
mount over base and secure by turning latch.
Secure Base & Support Bracket to 45º Bracket:
Assemble bracket according to diagram above. The
extended bracket (d, i, g, h) can be utilized to add
additional support. Ensure connection is tight.
(i)
(h)
(e)
(j)
(f)
(g)
(a) (d)
Mounting Option 4
Attach Bracket with Bolt & Attach Mount to Base:
Replace the bolt while securing the bracket. Place
mount over base and secure by turning latch.
3
INSTALLATION GUIDE: Mount

Ensure all screws and knobs are securely fastened
to prevent unwanted shifting.
Not for use while operating vehicle.
For safety reasons place mount a safe distance
from airbags.
Extend & Rotate Arms: Release latch by pulling it
away from the mount arm. Once released pull middle
joint upward until it has reached desired position. Secure
position by turning latch to locking position. To rotate
the arms & tray turn knobs at adjust to your liking.
Tighten knobs to secure.
Open
Close
Attach Brackets to Tray: Step 1: Attach rubber pads to
bracket tip. Step 2: Attach brackets to tray.
Secure Device to Tray: Extend brackets fully and place
device onto tray. Secure brackets tightly to edge of
device ensuring a tight connection.
Extending & RotateAttach Brackets to Tray
Secure Keyboard on Tray. Step 1: Place tray in a flat
position. Fully expand brackets. Step 2: Place keyboard
on top of tray. Secure brackets tightly to edge of
keyboard ensuring a tight connection.
Use Tray for Keyboard Case
Caution
Support
For questions or concerns please contact us at:
Customer Service Support
Toll Free: +1.877.JOY.FACT (877.569.3228)
[e-mail]
Use Tray with Device
INSTALLATION GUIDE: Adjustable Tray
4
1
2
1
2