JS Automation AIO3310/1A User manual

AIO3310/1/2A
Analog Input and
Multi-Function Digital I/O Card
User’s Manual (V1.2)
健昇科技股份有限公司
JS AUTOMATION CORP.
新北市汐止區中興路 100 號 6 樓
6F., No.100, Zhongxing Rd.,
Xizhi Dist., New Taipei City, Taiwan
TEL ： [phone]
FAX ： [phone]
http://www.automation.com.tw
E-mail ： [e-mail]

1
Correction record
Version
Record
1.0
firmware version 1.0 up
1.1
1.
Modify Notes on hardware installation
2.
Add Warranty
3.
Change orientation of JF1 connector (chapt. 5.1)
4.
Add specifications to each input and output (chapt. 6)
1.2
Add special note on PWM

2
Contents
1. Forward ............................................................................................................................................5
2. Features.............................................................................................................................................6
3. Specifications....................................................................................................................................7
3.1 AIO3310A Main card ................................................................................................................7
3.2 JS51026 37P DIN rail mounted dummy wiring board ...........................................................8
4. Layout and dimensions....................................................................................................................9
4.1 AIO3310/1/2A Main card..........................................................................................................9
4.2 JS51026 37P DIN rail mounted dummy wiring board ...........................................................9
5. Pin definitions.................................................................................................................................10
5.1 Pin definitions for JF1 (on card 37P) connector......................................................................10
5.2 Pin definitions for JM1 (extension 37P) connector.................................................................11
6. I/O interface diagram....................................................................................................................12
6.1 Digital I/O diagram..................................................................................................................12
6.2 Analog I/O diagram.................................................................................................................12
7. Hardware settings..........................................................................................................................13
7.1 Card ID setting.........................................................................................................................13
7.2 Digital I/O................................................................................................................................13
7.3 JP1,JP2 Jumper setting ............................................................................................................13
7.4 Timer/Counter..........................................................................................................................13
7.5 Analog input ............................................................................................................................13
8. Applications....................................................................................................................................14
8.1 Analog input section:...............................................................................................................14
8.2 Digital section:.........................................................................................................................14
8.3 Counter/Timer section: ............................................................................................................14
9. Ordering information....................................................................................................................15

3
Notes on hardware installation
Please follow step by step as you are installing the control cards.
1. Be sure your system is power off.
2. Be sure your external power supply for the wiring board is power off.
3. Plug your control card in slot, and make sure the golden fingers are put in right contacts.
4. Fasten the screw to fix the card.
5. Connect the cable between the card and wiring board.
6. Connect the external power supply for the wiring board.
7. Recheck everything is OK before system power on.
8. External power on.
Congratulation! You have it.
For more detail of step by step installation guide, please refer the file
“..\download\Supplemental_technical_data\Step_by_step_installation_of_Contrl_Card.pdf “ on the CD
come with the product or download the complementary documents from
http://www.automation.com.tw/common/Supplemental_technical_data.htm
Warning:
Some computer BIOS has “Auto detect DIMM/PCI clock” option, be sure to switch to
“DISABLE” else in some cases the PCI add on cards will not be detected by windows at cold start.

4
Warranty
The AIO3310/1/2A are warranted against defects in materials and workmanship for a period of two
years from the date of shipment, as evidenced by receipts or serial no. on board. JS automation Corp.
will, at its option, repair or replace product that proves to be defective during the warranty period. This
warranty includes parts, labor and shipping costs of returning.
Except as specified herein, JS automation Corp. makes no warranties, express or implied, and
specifically disclaims any warranty of merchantability or fitness for a particular purpose. Customer’s
right to recover damages caused by fault or negligence on the part of JS automation Corp. shall be
limited to the amount theretofore paid by the customer. JS automation Corp. will not be liable for
damages resulting from loss of data, profits, use of products, or incidental or consequential damages,
even if advised of the possibility thereof. This limitation of the liability of JS automation Corp. will
apply regardless of the form of action, whether in contract or tort, including negligence. Any action
against JS automation Corp. must be brought within one year after the cause of action accrues.
JS automation Corp. shall not be liable for any delay in performance due to causes beyond its
reasonable control. The warranty provided herein does not cover damages, defects, malfunctions, or
service failures caused by owner’s failure to follow the JS automation Corp. installation, operation, or
maintenance instructions; owner’s modification of the product; owner’s abuse, misuse, or negligent acts;
and power failure or surges, fire, flood, accident, actions of third parties, or other events outside
reasonable control.
If any defect occurs, you should email to us as the following form to get the fast response:
Detailed Company Information
Company/Organization:
Contact Person:
E-mail:
Address:
Country:
Tel/Fax:
Web Site:
Product information
product model:
serial no.:
Environment to Use: such as CPU board, Operating System, target application...
description of defect: (as detail as possible)

5
1. Forward
Thank you for your selection of our PCI bus AIO3310/1/2A a multi-channel analog input, and
multi-function digital i/o and timer/counter card.
An analog input card maybe as simply as just signal conversion, and the calibration job will be the
burden of the users. AIO3310A provides a new approach that each channel has been calibrated with our
precision instruments and all the records kept in the on-card eeprom to give the users a transparent
environment of accurate result at low card price.
Except for the calibration features, 2 byte-wide programmable TTL I/O ports also give users more
flexible functions to integrate the whole system.
Two 32bit Timer/counter ports also provide you versatile functions such as: programmable one-shot,
rate generator, square wave generator, software/hardware triggered strobe, event timer/counter, triggered
timer/counter, PWM generator, ….
Wish you would enjoy this card!
Other Analog I/O Card:
AIO3315/A12/16 bit Analog I/O and Digital I/O Card (PCI bus)
AIO3320A/1A isolated 8 12 bit A/D, isolated 8/16 16 bit D/A with 16 isolated digital I/O
(PCI bus)
AIO3382U Analog I/O Card, 8 AI 2 AO, 16 TTL , 2 multi- function timer/counter card
(Include bracket kit for TTL I/O) (PCI bus)
AIO3382UA/BAnalog I/O Card, 8 AI 2 AO, 16 TTL , 2 multi- function timer/counter card
(2 current source/ sink AO)(Include bracket kit for TTL I/O) (PCI bus)
AIO3384U Analog I/O Card, 8 AI 4 AO, 16 TTL , 2 multi- function timer/counter card
(Include bracket kit for TTL I/O) (PCI bus)
AIO3384UAA/BB Analog I/O Card, 8 AI 4 AO, 16 TTL , 2 multi- function timer/counter card
(4 current source / sink AO)(Include bracket kit for TTL I/O) (PCI bus)
AIO3384UAB Analog I/O Card, 8 AI 4 AO, 16 TTL , 2 multi-function timer/counter card
(2 current source AO , 2 current sink AO)(Include bracket kit for TTL I/O) (PCI bus)
AIO6328/A12/16 bit Analog I/O and Digital I/O PCI-104 Module
Any comment is welcome,
please visit our website
http://www.automation.com.tw/ for the up to date information.

6
2. Features
General
-PCI plug and play function with card ID for 16 identical cards
-Security password blocks illegal copy of software
Analog Function
-8/16/24 channel 16bit analog inputs (standard:8 channels)
-Software selectable input range: -10V~ +10V, -5V~ +5V , 0~10V, 0~5V
-Factory pre-calibrated analog conversion accuracy
Digital I/O Function
-2 byte-wide programmable TTL I/O
-IO00, IO01 as trigger/counter in, IO10,IO11 as trigger out of timer/counter function
Timer/Counter Function
-2 32bit multifunction counters up to 33MHz
-multi-function:
-- programmable one-shot
-- square wave generator
-- event counter
-- PWM generator

7
3. Specifications
3.1 AIO3310A Main card
Analog Input Block
-Input channels : 8/16/24 channel single end or differential (standard:8 channels)
-Resolution : 16bit
-Input range : -10V~ +10V, -5V~ +5V , 0~10V, 0~5V
-Input impedance: 100K ohm
-Range selection : software selectable per chip
-Conversion speed : 6us per chip (8 channel per chip)
-Accuracy : full range within 5mV (after calibration)
-Integral nonlinearity error: -3 ~ +3 LSB(max)
-Zero error: -28 ~ +28 LSB
TTL I/O Block
-I/O channels : 16 TTL (port 0,port 1)
-Configuration : byte input /output
-Output Capacity : (sink or source) 24mA @5V
-Output at power on : jumper configurable at high or low
Timer/Counter Block
-Channels : 2
-Data Length : 32 bit
-Specific Input : trigger in/ counter in via digital I/O port 0
-Specific Output : trigger out / counter out via digital I/O port 1
-Time Base : PCI system clock (33/66MH)
-Functions :
-- Programmable one-shot
-- Square wave generator
-- Event counter
-- PWM generator
General
-Security password : 10 bytes, user configurable
-Interrupt : software disable/enable
-Card ID : 16 locations set by rotary switch

8
-PCI bus data width : 32 bits
-Operation temperature : 0 to 70°C
-Storage temperature : -20 to 80°C
-Operation humidity : 5~95% RH, non-condensing
-Dimension : 156(W)*112(H)mm , 6.2(W) * 4.5(H)in
*Special Note on using PWM output
PWM output can be configured to isolated output or TTL output, owing to the interface
electric characteristics, the real output may be distorted by frequency bandwidth or on/off
delays. As for TTL, we recommend to check for the minimum duty. For the isolated output,
the PWM frequency and duty pulse width is limited not less than 100us and check the
response by a scope to verify the validity of your application.
3.2 JS51026 37P DIN rail mounted dummy wiring board
-Connection cable : D-type 37P cable to connect main and wiring board
-Dimension : 90(W)*113(L)*60(H)mm , 3.6(W)*4.5(L)*2.4(H)in

9
4. Layout and dimensions
4.1 AIO3310/1/2A Main card
*dimension in bare board
4.2 JS51026 37P DIN rail mounted dummy wiring board
*dimension in bare board