Jumpking Rectangle Combo User manual

12ft x 17ft Rectangle Combo
User Guide
WARNING: Read these assembly instructions carefully
before attempting to assemble or use this product. Keep
this user guide in a safe place for future reference.
Got a Problem building your trampoline?
Call us on 0344 800 4060 and we can help
Patent no: DE602006006495D1, EP1721640B1 and US7628731
Made In China

IMPORTANT INFORMATION
2
. WARNING! ADULT SUPERVISION & GUIDANCE REQUIRED AT ALL TIMES.
. Recommended age 6+ years.
. No somersaults or flips - can cause serious injury.
WARNINGS!
. Only for domestic use.
. Maximum user weight limit 140 kg.
. Not suitable for children under 36 months - small parts, choking hazard.
. Outdoor use only.
. The trampoline should be assembled by an adult in accordance with assembly instructions
and checked in every instance before use.
. Only one user. Collision hazard.
. Always close the net opening before jumping.
. Remove footwear before jumping on the trampoline.
. Do not use the mat / jumping bed when it is wet.
. Empty pockets and hands before jumping.
. Always jump in the middle off the mat / jumping bed.
. Do not eat whilst jumping.
. Do not exit by a jump.
. Limit the time of continuous usage (make regular stops).
. Do not use in strong wind conditions and sec
. The net should be replaced every 1 year.
ure the trampoline.
ADVISORY
. This trampoline is not intended to be buried in the ground.
. The following product dimension relate to this trampoline:
- Height from ground to top rail: 89 cm (0.89m)
- Height from ground to top of enclosure: 278 cm (2.78m)
- Height from top rail to top of enclosure: 189 cm (1.89m)
. The trampoline must be placed on a level surface at least 2m from any structures or
obstructions such as fence, garage, house, overhanging branches, laundry lines or electrical
wires.
. Do not install the trampoline over concrete, asphalt or any other hard surface not at
proximity of other conflicting installation, such as paddling / swimming pools, swings, slides
or climbing frames.
. Inspect trampoline / enclosure net before each use. Any damaged or worn parts must be
replaced before using the trampoline (see spare parts page 19).
. If an access ladder is used it should be removed when trampoline is not in use.
. Make sure there are no children / animals / obstructions underneath the trampoline.
. Access the trampoline through the door of the enclosure net only. Making sure you securely
close it before bouncing.
. Please don’t use when it’s windy or rainy as this can cause you slip and become injured.
. Don’t intentionally rebound off the enclosure net as this will weaken it.
. Only attach manufacturer approved accessories to the trampoline and enclosure net.
. Always jump in the middle of the mat and practice bounce techniques safety with adult
supervision and guidance.
. Jump without shoe.
. In certain countries during winter period, the snow load and the very low temperature can
demage the trampoline. It is recommended to remove the snow and store the mat and the
enclosure indoor.

JUMPING INSTRUCTIONS
Fundamental Bounce
1. Start from a standing position with
your head erect and your eyes on the
frame pad.
2. Swing your arms forward and up in a
circular motion.
3. Bring your feet together and point
your toes downward while in the air.
4. Keep your feet about 30 cm (15 in.)
apart from when landing on the bed.
Seat Drop
1. Land in a sitting position with your
legs parallel to the bed.
2. Place your hands on the bed beside
your hips.
3. Push with your hands to return to an
erect position.
Hand and Knee Drop
1. Start bouncing from a standing
position, keeping your eyes on the
frame pad.
2. Land on the bed on your hands and
knees.
3. Push with your hands and come back
up to an erect position.
HalfTurntable
1. Start from the front drop position
and push to the left or right with
your arms to begin turning your body
in the opposite direction.
2. Turn your head and shoulders
toward the direction that your body
is turning.
3. Keep your back parallel to the bed
and your head up.
4. After completing a half turn, land in
the front drop position.
Knee Drop
1. Start bouncing from a standing
position, keeping your eyes on the
frame pad.
2. Land on your knees, keeping your
back straight and your body erect.
3. Come back up to an erect position.
Swivel Hips
1. Start with a seat drop.
2. Turn your head to the left or right
and swing your arms up in the same
direction.
3. Turn your hips in the same direction
as your head and arms, completing a
twist.
4. Land in the seat drop position.
3
IMPORTANT PRECAUTIONS
surface.
1 user allowed at any one time.
This can result in serious injury to head, neck, arms or legs.

4
CARE & MAINTENANCE
Regular care and maintenance of your trampoline is required. This will help prolong its life and reduce
the possibility of injury. Neglecting this can lead to a risk for users.
Inspect your trampoline before each use using the checklist below as a guide. Take particular care in
doing this at the start of each season and at regular intervals. Ensure all parts are in tact and cannot
become dislodged during play, tighten any screws or nuts and bolts where required.
IMPORTANT: If any faults are found, the trampoline MUST NOT BE USED. We advise that the
trampoline is dismantled and placed in a dry place until new parts are
Looking after your trampoline:
Excess weight and improper use will damage it and
cause it to break easily.
If any part becomes dirty, clean with a damp cloth and dry thoroughly. Do
not use any abrasive cleaners as this could damage the product.
Prolonged exposure to sun
and harsh weather can shorten its life.
(available to buy from our website).
Common damage can be caused by water pooling, garden/outdoor debris landing on it, sparks
from nearby or displays landing on it.
their claws can damage it.
A trampoline can act like a sail in strong winds. It can be blown over
which can cause damage to the frame and surrounding areas. We recommend that it is moved
to a sheltered location and secured to the ground (tie-down kit available from our website), or
dismantled and stored away.
Follow assembly
instructions in reverse order making sure the springs are removed before dismantling frame.
To be lifted by 2 people. Lift slightly off the ground,
keeping the frame horizontal. Never drag to move it as this can displace parts. Always check that
parts are positioned correctly after moving.
PART
All Parts
Springs
Frame / Enclosure
Poles
Bed / Enclosure
Net / Frame Pad /
Foam Tubes
CHECKLIST
Securely attached
Correctly positioned
No sharp edges or points present
No missing parts
No damage (bent / broken)
No missing parts
No bent parts
No damage
No rusting or corrosion
No missing parts
(e.g. V-rings / Ties / Zips etc.)
No sagging
No damage
(Holes / Rips / Fraying / Tearing)
NOT OKOK

BUILDING YOUR TRAMPOLINE
Description:
Safety glasses
Description:
Cross-head screwdriver
Description:
Mallet
Description:
Gloves
WHAT YOU WILL NEED
1. This is a 2 person build.
2. Time for build is approximately 2 hours.
3. Choose a good location:
(wood chippings, sand or grass).
(7.3m) from ground level, away from
wires, trees and other possible hazards.
(2.5m) around sides, away from walls, fences, structures, tarmac
and other hard surfaces and play areas.
5

6
PARTS LIST
Part 2
Part 6Part 8
Part 11
Part 16
Part 21
Part 17
Part 18 Part 19 Part 20
Part 9
Part 14 Part 15
Part 3
Part 13
Part 12
Part 7Part 10
Part 4Part 5
Part 1
Description:
L-Top tube with
T-Connector +
welded tube
D marking
Quantity: 2
Description:
Description:
Stitched bed
Quantity: 1
Description:
Top enclosure poles
Quantity: 8
Description:
Enclosure netting
Quantity: 1
Description:
7inch Springs
Quantity: 144
Description:
Bottom enclosure
poles
Quantity: 8
Description:
Cords
Quantity: 8
Description:
Cap connector
Quantity: 8
Description:
L Legs
Quantity: 8
Description:
Spring tool
Quantity: 1
Description:
Quantity: 24
Description:
Centre legs
Quantity: 4
Frame pad
Quantity: 1
Description:
Black G3 poles
Quantity: 2
Self tapping screws
and spring washers
Description:
Top Tube
C marking
9 spring holes
Quantity: 2
Description:
Top Tube
B marking
9 spring holes
Quantity: 2
Description:
Top Tube
6 spring holes
Quantity: 2
Description:
L-Top tube with
T-Connector +
welded tube
A marking
Quantity: 2
Description:
T-Connector +
welded tube
2 pcs A 2 pcs B
2 pcs C 2 pcs D
Quantity: 8
Description:
Top Tube
D, A marking
10 spring holes
Quantity: 2
Description:
Top Tube
C marking
6 spring holes
Quantity: 4

7
Slot the narrow end of the top tube with
.rotcennoc-T
10
STEP 1 : ASSEMBLING THE FRAME
You will need the following parts to complete section 1:
2 x Part 1: L tube with D marking
2 x Part 2: L tube with A marking
8 x Part 3: T-connector+welded tube
(2xA, 2xB, 2xC, 2xD)
2 x Part 4: Straight tube with C marking(9 spring holes)
2 x Part 5: Straight tube with B marking(9 spring holes)
2 x Part 6: Straight tube A D marking(10 spring holes)
4 x Part 7: Straight tube C marking(6 spring holes)
2 x Part 8: Slightly bent tube D marking(6 spring holes)
8 x Part 9: L leg
4 x Part 10: Centre Leg
16 x Part 18: Self tapping screw + washers
3
9
189
10
12
L-Top tube
D marking
L-Top tube
A marking
Centre leg
L Leg
You will also need a cross-head screwdriver
(not supplied).
Self tapping screw and washer
Cross-head screwdriver
4
5
Top tube C marking(9 spring holes)
Top tube B marking(9 spring holes)
8Slight bent top tube (6 spring holes)
Slight bent top tube
(6 spring holes)
With D marking
With C marking
Long - 9 spring holes
6
Top tube D A marking(10 spring holes)
7
Top tube C marking(6 spring holes)
Top tube C marking(6 spring holes) Top tube C marking(6 spring holes)
With A marking
With B marking
Long - 9 spring holes
Place Part 1 - L tube upside down and attached Part 3 T-connector+welded tube with D marking to the long endjoin Part 4 top
tube with C marking(9 spring holes) to the short end and attachPart 3 - T-connector+welded tube with C marking.
N.B.: The letters on the welded tube will facing outwards. Screw holes on T-connector+welded tubes facing towards one
another.
Place Part 2 - L tube upside down and attach Part 3 T-connector+welded tube with A marking to the long end join Part 5 top
tube with B marking(9 spring holes) to the short end and attachPart 3 - T-connector+welded tube with B marking.
Insert the center leg and leg extensions into upright tube on T-connector.
Note: You may need to tap the leg extension in using a rubber mallet or by placing a
piece of wood over the top of the tube. Do not use a metal hammer on the metal tube
as this may distort the end of tube.

8
Important: The frame is held together under
tension so you will have to use some force to
insert certain parts.
Place your feet on the top tubes and grip the leg
extension with both hands.
Pull the extension until it can be slotted into the
T-connector.
Slot the end of leg extension into the
T-connector.
Push down on the end of the centre leg to fully
.rotcennoc-Tehtotninoisnetxegelehttesni
You have now completed the frame section.
Repeat the last two steps until you have
assembled the remaining sections of the trampolines
frame.
You have now completed step.
Screw one of the self tapping screws through the
slot in the T-connector and into the hole in
the leg extension using the cross-head screwdriver.
With B marking
With A ma
A marking
A marking
B marking
B marking
rking
Top tube C marking
6 spring holes
Top tube C marking
6 spring holes
Top tube D marking
6 spring holes
Top tube C marking
6 spring holes
Top tube C marking
6 spring holes
Top tube D marking
6 spring holes
D marking
D marking
C marking
C marking

9
This step will require 2 people who must be
wearing gloves.
Slot two of the frame section together as shown in
the diagram.
You will now need to slot the frame together, this
will take some force. The easiest method is if the
two people face each other.
Important:
Numbers relate to amount of
spring holes on top rail.
Ensure all of the top tubes, leg
extensions and centre legs are fully inserted.
The frame is now fully assembled and you have
now completed step 2.
Hold the top tubes either side of the
T-connector+welded tubes and push
towards each other until the loose end of the
frame can be inserted into the T-connector.
STEP 2 : ASSEMBLING THE FRAME
AA
A
A
A
A
B9
B
B9
B
C6 C9
C
C6
C6
C
C9 C6
D6
D6
D
D10
D
D10
D
D
Attach Part 6: top tube with A D markings (10
spring holes) in between the T-connector+welded
tube marked A and D.
Attach Parts 7 and 8 the completed sections
marked C, D, C between T-connector+welded
tubes B and C.

10
STEP 3 : FITTING THE STITCHED BED
This step will require 2 people who must be
wearing gloves and protective eye wear.
Lay the stitched bed (with the V-Rings) out inside
the frame of the trampoline with the warning labels
facing upwards.
Please note the bed is 2 foot smaller than the frame.
Locate the 4 V-Rings with the yellow stitching.
These will be at 4 corners.
Slot one of the springs onto one of the yellow
stitched V-Rings as shown.
Important: springs must be slotted on the right way
around with the more curled end of the spring
hooked to the V-ring.
Slot the other end of the spring into one of the
spring slots in the top of the frame.
IMPORTANT: Ensure the spring is fully
inserted into the slot on the top of the frame.
Yellow
stitching

11
Attach a spring to the diagonal yellow stitched
V-Ring.
Important: You will now need to use the spring
tool to attach the spring to the frame.
Hook the spring tool onto end of spring, and pull
until the spring can be slotted into the spring slot
on the top of the frame.
IMPORTANT: Ensure the spring is fully
inserted into the slot on the top of the frame.
Attach four more springs to the V-Rings then attach
them to the frame next to the T-connector+welded tube.
T-connector+welded tube
Continue to attach springs in the same sequence
as above: in the middle of each section, making
sure the next spring is attached on the opposite
side to even out the tension.
Important: The stitched bed is designed like
elastic to be bouncy, which means that during
construction it may look like it won’t Please
note that it will stretch to the correct size when
attaching the springs, this may take some force.
The stitched bed is now and you have
completed step 3.
1
2
3
4
5
6
7
8

12
STEP 4 : FITTING THE FRAME PAD
This step will require 2 people.
Lay the frame pad - Part 13 out over the edge of
the frame with the ties facing downwards.
Align the openings in the frame pad with the
T-connector+welded tube's on the frame.
The frame pad is now and you have
completed step 4.
WARNING: The trampoline MUST NOT be used
during construction.
ABC
Frame Pad Frame Pad
Frame Pad
Top tube
Top tube
Top tube
Webbing Webbing Webbing
D-ring D-ring
D-ring
Look under the trampoline and locate the pairs
of straps near the edge of bed(6) and Double
D-ring and webbing near the frame.
See the inset drawing. A, B and C. Repeat this
step with the remaining straps (not shown).

STEP 5 : FITTING THE ENCLOSURE TUBES
You will need the following parts to complete step 5:
8 x Top enclosure tubes
- Part 14
8 x Bottom enclosure tubes
- Part 15
8 x Self tapping screws & washers -- Part 18
You will also need a cross-head screwdriver (not
supplied).
Slot the thin end of one of the bottom enclosure
tubes into the open end of one of the top
enclosure tubes.
Align the hole in the bottom enclosure tube with
the slot in the top enclosure tube.
Screw one of the self tapping screws through the
slot in the top enclosure tube and into the hole in
the bottom enclosure tube using the cross-head
screwdriver.
Top enclosure tube
Bottom enclosure tube
Self tapping screw and washer
Cross-head screwdriver
13

14
Slot the bottom enclosure tube into the tubes in
stolsehthguorhtelbisivsebutdedlew+rotcennoc-Teht
in the frame pad.
Assemble the seven enclosure tubes
using the three self tapping screws and the
cross-head screwdriver.
Slot the eight enclosure tubes into the
T-connector+welded tube's on the frame.
The enclosure tubes are now and you have
completed step 5.
Screw one of the self tapping screws through the slot
in the tubing and into hole using the cross-head
screwdriver.

STEP 6 : FITTING THE ENCLOSURE NETTING
You will need the following parts to complete step 6:
1 x Enclosure netting - Part 17
Lay the enclosure netting out on the trampoline.
Enclosure
netting
15
2 x Black G3 poles - Part 16
Find the sleeves that run along the top of the
enclosure netting.
Slot the thin sections on the two black G3 poles
into the metal ends so the poles become two long
sections.
Black G3
poles
You may need to slide the connected poles around
in the nettings sleeves until the thin black sections
are aligned with the gaps between sleeves.
The corners of the G3 rod jut out of a long cut out
section of the netting.
The zip of the door is on the long side of the
trampoline.
Stand on the trampoline and insert one of the
exposed sections of the Black G3 pole into a
plastic grip on top of one of the enclosure tubes.

Attach the seven other exposed sections of the
FRP rods to the other enclosure tubes in the
order shown in the diagram.
The enclosure net is now and you have
completed step 6.
16
4
5
6
78

17
STEP 7 : ATTACHING THE BOTTOM OF THE NET
You will need the following parts to complete step 7:
8 x Cords
- Part 19. .
Tie one end of the cord around a V-ring on the bed
of the trampoline. Push the outer end through a
hole in the bottom of the netting. Sew in and out
using every V-ring and a hole in the netting nearest
that V-ring.
Important: Keep the cord tight at all times.
Continue to do this until all the net is sewn in,
typing off the rope and starting the next when is has
come to the end.
From the underside of the trampoline, tie the
remaining elastic straps around the springs or
through the V-Rings.
You have completed step 7 and the trampoline is
fully assembled.

USING THE TRAMPOLINE
To enter the trampoline, unzip the door and climb
in.
Always close the doorway before using the
N.B.: The zip will be on the long side of the
trampoline.
trampoline.
Ensure that there is 7.3 metres (24 feet) clearance
above the trampoline.
Also check that there are no overhanging objects
in the area above the trampoline.
7.3m
24ft
Door
zip
18
2.5m
8.2ft
Before using your trampoline, check again that
there is enough clearance around it. Maintain a
clear space of 2.5 metres (8.2 feet) on all sides of
the trampoline.
Also check that the area is free from walls,
structures, fences, tarmac and other hard surfaces
and other play areas.

SPARE PARTS
For a full range of accessories and replacement parts call 0344 800 4060
or visit our web site at: www.jumpking.eu
Customer Helpline on: 0344 800 4060.
To help us assist you, please provide the following information when calling:
12’ x 17’ Rectangle Combo
(see parts list below).
21
19
18
Key
No. Qty. Description
Key
No. Qty. Description
24
16
11
20
10
10
3
3
9
9
1
6
5
10
9
8
779
12
13
14
15
21
23
17
74
2
7
8
22
Welded T-connector
To order replacement parts, you can email us on: [email protected], or call our
1 2 L Frame with D marking
2 2 L Frame with A marking
3 8 T-connector+welded tube
(Ax2, Bx2, Cx2, Dx2)
4 2 Straight tube with C marking
(9 spring holes)
5 2 Straight tube with B marking
(9 spring holes)
6 2 Straight tube with A D marking
(10 spring holes)
7 4 Straight tube with C marking
(6 spring holes)
8 2 Slightly bent tube with D marking
(6 spring holes)
9 8 L leg
10 4 Centre leg
11 144 7” springs
12 1 Bed
13 1 Surround pad
14 8 Bottom enclosure poles
15 8 Top curved enclosure poles
16 1 G3 Rod - 2 in pack
17 1 Net
18 1 Self tapping screws pack of 24
19 1 Ropes - 8 in pack
20 1 Spring tool
21 8 Enclosure plastic cap
22 8 Connector cap
23 8 Foam sleeve
24 1 User Manual