Jumpking OR1413B6A1 User manual

2

®
CONTENTS
                           

   
  
  

 
  
  
3

1. Trained Spo er supervision is recommended.
2. Must place the trampoline on lawn, bark wood chip, sand or cushioning materials.
3. Maintain a free space of minimum 2500mm on all sides of the trampoline. This area should not included
concrete, bitumen, brick, or other hard surfaces as these can cause serious injuries.
4. Adequate overhead clearance is essen al. A minimum of 24 from ground level is recommended.
Provide clearance for wires, tree limbs, and other possible hazards.
5. Lateral clearance is essen al. Place the trampoline and trampoline enclosure away from walls, structures
,
fences, and others play areas. Maintain a clear space on all sides of the trampoline and trampoline
enclosure.
6. Place the trampoline and trampoline enclosure on a level surface before use.
7. Use the trampoline and trampoline enclosure in a well-lighted area. Ar cial illumina on may be
required for indoor or shady areas.
8. Secure the trampoline and trampoline enclosure against unauthorized and unsupervised use.
9. Remove any obstruc ons from beneath the trampoline and trampoline enclosure.
10. The trampoline enclosure is only to be used as an enclosure for a trampoline of a size for which the
enclosure is designed.
11. The owner and supervisors of the trampoline are responsible to make all users aware of prac ces
speci ed in the use instruc ons.
12. DO NOT a empt or allow somersaults on the trampoline. Landing on the head or neck can cause serious
injury, paralysis, or death, even when landing in the middle of the bed.
13. Do not allow more than one person on the trampoline and trampoline enclosure. Use by more than one
person at the same me can result in serious injuries.
14. Use trampoline and trampoline enclosure only with mature, knowledgeable supervision.
15. Trampoline over 20 in. (51 cm) tall are not recommended for use by children under 6 years of age.
16. The trampoline is designed for users weighing 90 kg (200 lbs.) or less.
17. Misuse and abuse of the trampoline is dangerous and can cause serious injuries.
18. Injury may result from encountering the frame or falling through the springs while ge ng onto or o the
trampoline or while jumping. Stay in the center of the bed when jumping. Do not use the trampoline
without the frame pad securely in place to cover the frame. The frame pad is not designed or intended to
support the weight of the user. Do not step or jump directly onto the frame pad.
19. The trampoline is a rebounding device that propels the user to unaccustomed heights and into a variety
of body movements. Rebounding o the trampoline, striking the frame or springs, or improperly landing
on the bed may cause injury.
20. Do not jump on the trampoline while holding an object, par cularly one that is sharp or breakable.
21. Inspect the trampoline and trampoline enclosure before each use. Make sure the frame padding, barrier
and the enclosure support (frame) padding is correctly and securely posi oned. Replace any worn,
defec ve, or missing parts.
22. Climb on and o the trampoline. It is a dangerous prac ce to jump from the trampoline to the oor or
ground when dismoun ng, or jump onto the trampoline when moun ng. Do not use the trampoline as a
springboard to other objects.
23. Stop bounce by exing knees as feet come in contact with the trampoline bed. Learn this skill before
a emp ng others.
24. Learn fundamental bounces and body posi ons thoroughly before trying more advanced skills. A variety
of trampoline ac vi es can be carried out by performing the basic fundamentals in various series and
combina ons, performing one fundamental a er another, with or without feet bounces between them.
25. Avoid bouncing too high. Stay low un l bounce control and repeated landing in the center of the
trampoline can be accomplished.
C
ontrol is more important than height.

26. While keeping the head erect, focus eyes on the trampoline toward the perimeter. T
his will help control
bounce.
27. Avoid bouncing when red. Keep turns short.
28. Properly secure the trampoline when not in use. Protect it against unauthorized use. If a trampoline
ladder is used, the supervisor should remove it from the trampoline when leaving the area to prevent
unsupervised access by children under 6 years of age.
29. Keep objects away which could interfere with the performer. Maintain a clear area around the
trampoline.
30. Do not use the trampoline while under the in uence of alcohol or drugs.
31. For addi onal informa on concerning the trampoline equipment, contact the customer services Hotline
number 1-877-927-8777.
32. For informa on concerning skill training, contact a cer ed trampoline instructor.
33. Bounce only when the surface of the bed is dry. Wind or air movement should be calm to gentle. The
trampoline must not be used in gusty or severe winds.
34. Real all instruc ons before using the trampoline and trampoline enclosure. Warnings and instruc ons for
the care, maintenance, and use of this trampoline and trampoline enclosure are included to promote
safe, enjoyable use of this equipment.
35. Users may become entangled in or strangled by loose cords or in gaps between trampoline and
enclosure.
36. Keep enclosure ghtly fastened to the trampoline in accordance with manufacturer’s instruc ons. Failure
to properly assemble and maintain a ght, secure trampoline/enclosure boundary may result in serious
injury, strangula on, or death.
37. Do not a empt to jump over the barrier.
38. Do not a empt to crawl under the barrier.
39. Do not inten onally rebound o the barrier.
40. Do not hang from, kick, cut, or climb on the barrier.
41. Wear clothing free of drawstrings, hooks, loops or anything that could get caught while using the
trampoline/enclosure and result in entanglement or strangula on, or both.
42. Do not a ach anything to the barrier that is not a manufacturer-approved accessory or part of the
enclosure system.
43. Enter and exit the enclosure only at the enclosure door or barrier opening designated for that purpose.
44. The trampoline frame and the enclosure are made of metal. They are not grounded, and they will
conduct electricity. Therefore, an electrocu on hazard exists.
45. Keep all frame and heat sources away from the product.
24. Learn fundamental bounces and body posi ons thoroughly before trying more advanced skills. A
variety
of trampoline ac vi es can be carried out by performing the basic fundamentals in various series and
combina ons, performing one fundamental a er another, with or without feet bounces between them.
25. Avoid bouncing too high. Stay low un l bounce control and repeated landing in the center of the
trampoline can be accomplished. Control is more important than height.
death, as well as property damage. To reduce these risks, disassemble the trampoline and enclosure and
from moving as a result of the wind, but even anchored trampoline can become airborne or damaged.
46.

The placard shown at the below must be attached to the trampoline enclosure by the owner (see assembly step
15 on page 20). If the placard is missing or illegible, call our Customer Hotline toll free at 1-877-927-8777,
Monday through Friday, 8 a.m. until 5 p.m. Central Time, to order a free replacement placard.
Note: The placard is not shown actual size.
OR1413B6 A1
Do not attempt or allow
somersaults. Serious injuries,
paralysis, or death may result.
To reduce the chance of
landing on your head or neck,
do not do somersaults(flips).
Do not allow more than one person
on the trampoline at a time.
While keeping the head erect, focus eyes on the trampoline toward the perimeter.
Avoid bouncing when tired.
OR1413B6A1
WARNING
Use trampoline only with mature,
knowledgeable supervision.
Not recommended for children under 6
years of age.
Read instructions before use.
Inspect before use and replace any worn,
defective or missing parts.
OR 1413B 6A1

1-877-927-8777,

8

the
sharply
spot.

Connect Toprail(2) with t-connector w/slot(4) to toprail(1) with t-connector(3).
Then connect another toprail with t-connector to finish 1 section. Should
have total of 4 sections (a and b) completed as below diagram.
Lay out all of the parts in groups :
4 Toprails with T-connector w/ round slot (2)
8 Toprails with T-connector (1)
12 Leg extensions (5)
6 " W" shaped legs (6)
Once the leg sections has been connected, lay it out as seen: Making sure A
sections lay across from each other. B sections lay across from each other but
the legs should not match laying on the same directions as seen:
A
A
A
A
B
B
B
B
2.1) Have 2 people connect the section A and B together. Follow the steps
until all 4 sections has been connected and is now a full circle.
2.2) Now bring in the leg section and connect it to the 2 T-connector as
shown.
2.3) Finish connecting the last leg section to the other 2 T-connectors.
1. 1.
2. 2.
2.1.
A
A
B
B
2.2. 2.3.
A
A
B
B
1
2
5
6
T-connector+
Welded tube(4)
T-connector+
Welded tube(4)
A
A
B
B

16
Frame
Holes
V-rings
7
9
9
Springs (9)
19
Hook the V-ring
V-ring
7
9
9
Frame
Black webbing with yellow line
No yellow line
3. Lay the Bed (7) on the ground inside of the
assembled frame. Make sure that the two warn-
ing decals (not shown) are on top of the Bed.
Note: There are V-rings around the edge of the
Bed (7) and holes around the top of the frame.
During this step, you will attach the Bed to the
frame using the included Springs (9) for holes
on top of frame and for holes on bottom of frame
(see the inset drawing). Hook a spring to the
Bed(7) and using the spring pulling tool(19), pull
the spring from the Bed to the hole slot in the
trampoline frame with even spring tension.
Be careful where you place your hands, the
Springs and frame joints can pinch.
To attach each Spring, you will first hook one end
of the Spring into a V-ring with black webbing
with yelow line location (see the inset drawing).
Hook the first two Spring(9) into two the V-rings
(black webbing with yellow line) on the Bed(7) and
into the holes on the top tube. Attach two more
Springs (9) with black with yellow line location
directly across the Bed (with the webbing) from the
first two Spring. Attach two more Spring(9) with
black webbing with yellow line location halfway
between the first/second Spring(9), so eight
Springs(9) are attached as shown. Attach four
more Springs(9) (not shown) halfway between
the first eight Springs(9). Continue attaching
Springs(9) halfway between the previously attached
Springs,until all the Springs are attached.
During the installation of springs, wear
gloves and protective eye wear.

17
4
4. Lay the Frame Pad (8) on the frame.
Do not use the trampoline without the
Frame Pad (8), which is designed to reduce the
likelihood of injury to the user from coming in con-
tact with the trampoline frame. If you do not
have a Frame Pad, call our Customer Hot Line
toll-free at 1-877-927-8777, Monday-Friday,8 a.m.
-5 p.m. Central Time.(Excluding Holidays)
Properly install the Frame Pad before using the
trampoline.
Thread one end of Elastic Tie-Down, then tie a knot
on V-Ring.
Repeat this step with the remaining straps which at
middle position of each pad section (not shown).
Elastic Tie-Down
Spring
V-Ring
V-Ring
5
ABC
Frame Pad Frame Pad
Frame Pad
Top tube
Top tube
Top tube
Webbing Webbing Webbing
D-ring D-ring
D-ring
Look under the trampoline and locate the pairs
of straps near the edge of bed(7) and Double
D-ring and webbing near the frame.
See the inset drawing. A, B and C. Repeat this
step with the remaining straps (not shown).
5.
Elastic Tie-Down
Strap with Double D-ring on the pad edge
Safety pad(8)
D-ring
T-connector Webbing
Webbing
Double D-ring in the middle of pad should be
fixed exactly close to the right of T connector
on the top rail.
Double D-rings on the middle of pad should be fixed
exactly on the right of each T-connector of frame.
8

6. Using the included plastic tie, attach the Safety
Placard (10) to the frame near the point where
jumpers will climb onto and off the trampoline.
The trampoline is now fully assembled. Make
sure that all parts are securely attached.
Familiarize yourself and all users of the tram-
poline with the safety precautions, use and
instructional materials, and care and mainte-
nance instructions in this manual before using
the trampoline.
6
Frame
7. Lay a Straight Tube(11) and a Top Tube (12)
with Plastic Cap on the ground.
Make sure that the Straight Tube (11) is oriented
so the small holes are in the position shown.
Slide a Foam Sleeve (17) onto each of the tubes;
note that the ends of the Straight Tube (11) should
not be covered.
Insert the Straight Tube (11) into the Top tube(12).
Tighten a Self-tapping Screw (13) into the small hole
in the Tube (11,12).
Assemble the remaining Straight Tubes (11), Top
Tubes (12), and Foam Sleeves (17) in the same
way.
7
8
Tighten Self-tapping Screw
Into Small Hole
Small Hole
Plastic Cap
(15)
11
12
13
11
18
17
17
17
17
Plastic Cap
(15)
T-connector(4)
Straight tube (11)
8. Insert the end of Straight Pole (11,12) into the hole
of T-connector+Welded tube (4).
Attach the other three Straight Pole (11,12) in the
same way. See inset drawing.
Attach the Poles(11,12) as above arrow drawing
shown.
Leg
7
8
11
12

9. Lay out Top G3 Pole (14), joint each section
Connector to a straight line as shown.
Assemble the remaining Top G3 Pole (14) in the
same way.
Spread the Netting (16) on the trampoline bed,
insert a Top G3 Pole (14) into the opening of
Top Sleeve on the Netting (16). Insert the
other Top G3 Pole (14) into the opposite
opening of Top Sleeve on the Netting (16).
Insert the pole into sleeve of the Netting(16)
Netting(16)
Opening
Joint the end of each pole by Clip of Connector
Start:
Finish
Door of Netting
Top Sleeve
10. Joint each end of Top G3 Pole (14) by the clip of
connector at each opening. The Top Sleeve of the
Netting (16) become a round shape.
6 Sections Per Line
Top G3 Pole (14)
Spread out G3 Pole and Joint each section
to one straight line.

11. Note: During steps 12 and 13, you will “sew” the lower
edge of the Netting(16) to the V-rings on the bed using
the Cords(18).
Locate the V-ring closest to the door. Thread one end
of a Cord(18) through the lower edge of the Netting(16)
above the V-ring and then thread the Cord through the
V-ring. Tie the Netting to the V-ring, by making a double
knot in the Cord.
12
13
16
18
16
18
12. Thread the Cord(18) through the lower edge of the
Netting(16) halfway between the first V-ring and the
V-ring to the left, and then thread the Cord through
the V-ring to the left. Repeat this procedure until
the entire Cord is threaded through the Netting and
the V-rings as shown. Keep the Cord taut. Tie the
end of the Cord to the last V-ring that it reaches.
Tie a second Cord(not shown)to the last V-ring
reached by the first Cord. Thread the second Cord
through the Netting(16) and the V-ring as described
above. Repeat this procedure with the remaining
Cords until the last Cord reaches the first Cord.
(Note: The last Cord may overlap the first Cord.)
Make sure that the Netting is sewn to every V-ring
on the trampoline bed; the Netting below the door
must also be sewn to the V-rings.
13. Using the included plastic tie,attach the Safety
Placard(10)to the Netting(16)near the door as
shown.
The trampoline/enclosure is now fully assembled.
Make sure that all parts are securely attached.
Familiarize yourself and all users of the trampo-
line/enclosure with the safety precautions, use
and instructional materials, and care and mainten-
ance instructions in this manual before using.
Disassembly
To disassemble the trampoline/enclosure,follow assembly steps 1 through 14 in reverse order.
Do not attempt to disassemble any trampoline frame components before the springs and the bed
have been removed. Use gloves to protect your hands from pinch points during disassembly.
11
20
10