JumpXfun Extreme 426cm User manual

90 cm
270 cm
426 cm
It is very important that you read and understand the instructions before assembling and
using the trampoline.
We hope that you will enjoy using the trampoline. A trampoline is great fun and at the same time
good exercise. It takes some time to assemble so please read all the instructions before starting
and it will be easier. It is possible that the assembly will take more than an hour, so be patient and
get the assistance of a friend.
Assembly Instruction
JumpXFun trampoline
–
Extreme 426cm

IMPORTANT
Read the following statements and warnings to avoid serious or fatal injury.
Warning.
- Max 150 kg.
- Only for domestic use.
- Outdoor use.
- Only one user. Collision hazard.
- The net should be replaced every year.
- Adult supervision required.
- Do not perform somersaults (flips).This is very dangerous and you risk serious injury or death
- Always close the safety net opening before jumping.
- Read the instructions.
- The trampoline shall be assembled by an adult in accordance with the assembly instructions
and then checked before the first use
- Jump with proper gym shoes or barefoot only.
- Empty pockets and hands before jumping.
- Always jump in the middle of the mat.
- Do not use when the mat is wet.
- Do not eat while jumping.
- Do not exit by a jump.
- Limit the time of continuous usage (take regular breaks).
- Do not use in strong wind conditions and secure the trampoline.
- Do not try to jump over the net.
- Do not purposely jump onto the net.
- Do not try to purposely rebound off the safety net.
- Do not hang on the top of the net, or try to climb the netting.
- Take off any jewellery that could become entangled with the netting or cut the netting.
Placement of the trampoline
Do not place the trampoline on a concrete floor or other hard surfaces. The ideal placement is a
level, stable surface like a lawn. There must be at least 2 meters of space around the trampoline.
Check that there are no wires, tree branches, fences or other possible hazards above and around
the trampoline. The trampoline should not be placed near any pools, swings, slides, climbing
frames or other obstructive installations. The trampoline is not intended to be buried into the
ground.
Weather conditions
The trampoline should not be used when wet. In winter conditions, please disassemble the
trampoline and store all fabric parts (mat, foam pad, safety net) inside. In strong wind conditions,
disassemble the foam pad and safety net and secure the trampoline to the ground using Ground
Stakes/Anchors (sold separately).
How to use
Take it easy at first. Don’t try difficult move
Do not jump when tired - this increases the risk of injury. Be sure to wear proper shoes, e.g. gym
shoes, or be barefoot when jumping.
Never step on the frame pad. It is not constructed to support the weight of a person. Never
dismount by jumping off the trampoline. Always climb off. Don’t use the trampoline under the
influence of drugs or alcohol.
Always have someone else watching while you jump. If you should injure yourself you will have
someone to assist you.
Always start your jump at the centre of the mat. If you land more than 30 cm away from the edge
of the logo, stop your jump immediately!
Restart your jump at the centre of the mat.
Assembly
Please read the assembly instructions fully before starting to assemble the trampoline. It is
advisable to have two people assembling it together.
Start first by checking that you have all the required parts. The reference No. of each part will be
used in the instructions to guide you.
2

Parts No. Parts Description Quantity
1Trampoline Mat, stitched with
Triangle-Rings 1
2 Frame Pad 1
3 Top Rail with Leg Sockets 6
4 Top Rail 6
5 Leg Base 6
6 L-Shaped Leg 12
7Galvanized Springs
(3,5mm x 34N) 84
8 Spring Loading Tool 1
9 Arc Washer 12
10 Screw 12
11 Allen Wrench 1
12 Spring Washer 12
13 Self-Locking Screw (Small) 12
TRAMPOLINE Parts List
3

Parts No. Parts Description Quantity
AUpper Frame Tube with
Long Foam 6
BMiddle Frame Tube with
Long Foam 6
C Lower Frame Tube with No Foam 6
D U-Screw 12
E Clamp 12
F Lock Nut 24
G Gap Spacer 12
H Self-Locking Screw 18
I Cable Wire 12
J Plastic Cap 6
K Cord 9
L Enclosure Netting 1
M Nut Cover 24
N Wrench 1
O PVC Sleeve 6
P Cap 6
Q End Cap 6
SAFETY NET Parts List:
4

6 6
10 5
9
6
6
5
3
4
Trampoline assembly
Two people required for assembly.
Step 1
Start by building the frame. Slide the pieces together.
Begin by laying out the pieces as shown in the picture.
Step 2
Slide two “L-shaped Legs” 6 into the “Leg Base” 5 as shown. Repeat this step for all the
Leg Bases. Secure with the “Screw” 10 and Arc Washer 9 .
5

12 13
11
5
6 6
3
6 6
5
4
6
3
666
Step 3
Take the leg support built in step 2. This part will be simpler if one person holds the leg support
and another person puts the “Top Rail with Leg Sockets” 3 in place as shown. Repeat for all legs.
Now insert the remaining “Top Rail” 4 into the spaces between leg supports as shown.
Screw in the “Self-Locking Screw (Small)” 13 and “Spring Washer” 12 as shown. Do not tighten
fully at this point.
6

TRAMPOLINE MAT
1
7
Step 4
Please take care when attaching the springs.
Start by laying out the “Trampoline Mat” 1 inside the frame.
Select a point to start. Call this 1. Use the special spring tool to attach the “R-hook Springs” 7
as shown.
Start by putting the hook of the spring in the V-shaped ring on the trampoline mat. Then use
the special tool to pull the spring into place on the frame. Make sure that the spring hooks on
completely otherwise it may come loose during jumping. When doing this you should wear
protective gloves to avoid injuries.
When the first spring is in place continue with the next in the numerical order shown on the
picture. When you have completed number 16 you can attach the remaining springs in any order.
It is important to follow this instruction carefully to get the right tension for the trampoline mat. If
you do not follow this pattern it will be very difficult to assemble the trampoline mat correctl .
7

2
Step 5
Lay the “Frame Pad” 2 over the trampoline so that it covers the springs and the metal frame. Line
up the straps so that you have one over the leg sockets and one between. Make sure to tie the
straps tightly. Tie the straps as shown.
Now go back and tighten all screws firmly on the trampoline
8

CQ
E
F
M
G
D
B
H11
C
Safety Net assembly
Two people required for assembly.
Step 6
Attach “End Cap” Q to the “Lower Frame Tube with No Foam” C making sure it is fitted at the
correct end as shown.
Attach the “Lower Frame Tube with No Foam” C to the leg frame, using the “U-screw” D , “Gap
Spacer” G and secure with the “Clamp” E and the “Lock Nut” F as shown.
Hint: Don’t tighten all lock nuts at once. Tighten all the lock nuts at the end of Step 7.
Step 7
Attach the “Middle Frame Tube with Foam” B to the “Lower Frame Tube with No Foam” C .
Screw in the “Self-Locking Screw (Small)” H as shown. Do not tighten fully at this point.
After all the U-screws have been assembled, tighten all lock nuts. Put the “Nut Cover” M onto the
“Lock Nut” F to avoid injury.
Please note that only the lower U-screws need to be covered.
Repeat step 1 and 2 for all frame tube sets and tighten all the nuts.
Note: The Lower “U-screw” should be placed about 30 cm from the ground, while the Upper
“U-screw” should be placed right above the end of the “Leg Socket” (80 cm from the ground).
2
9

N
I
I
L
J
A
11 H
Step 8
Pull the foam down slightly to locate the hole on the curved end of “Upper Frame Tube with Foam”
A .
Attach the “Plastic cap” J and secure with the “Self-Locking Screw” H .
Repeat on all tubes.
Step 9
Connect the thread to the nut of “Cable Wire” I by using the “Wrench” N as shown. Then insert
the two groups of Cable Wires into the sleeves of the “Enclosure Netting” L respectively.
Two people should now hold both ends of the wire respectively, so that all the Cable Wires form a
circle. Then connect the two ends of cable Wires together by connecting the thread to the nut
as shown.
Now place the Cable Wires with the Enclosure Net on the Trampoline Mat for further assembly.
10

A
O
J
P
L
B
A
11
H
A
B
Step 10
Slide in “PVC Sleeve” O into “Upper Frame Tube with Long Foam” A . Please make sure the tie
on the upper part of the Sleeve is on the top. Secure the top opening of the Sleeve with a tie.
Then slide the Cable Wire in to the “Plastic Cap” J assembled on the Upper Frame Tube with
Long Foam. Make sure the cable wire fits into the slot properl . Pull down the PVC Sleeve O to
cover up all the foam as shown.
Finally, put the ”Cap” P onto the “Plastic Cap” J .
Repeat for all tubes.
Step 11
Now lift the assembled “RING” up to attach the “Upper Frame Tube with Long Foam” A to the
“Middle Frame Tube with Foam” B .
Make sure all legs are in place before securing with the “Self-Locking Screw” H .
11

L
K K
Step 12
First, tie the end of one “Cord” K to the Trampoline Mat ribbon. Then pull the cord through the
corresponding hole on the net as shown. Repeat this step until you have tied all the “Cord” K to
the Trampoline Mat ribbon and tie both ends together.
Step 13
Pull the zip of the “Netting” L at the door which should be located within one leg base of the
Trampoline, then snap the two buckles together as shown.
Step 14
Important: Remember to go back and tighten all screws, nuts and buckles on both the Trampoline
and the Enclosure Netting. Otherwise it may not function properly and may lead to injuries that
could have been avoided by proper assembly.
The assembly of the trampoline is now complete. Remember to be careful when jumping.
12

KNEE BOUNCE
BASIC BOUNCE
SEAT BOUNCE
FRONT BOUNCE
180 DEGREE BOUNCE
BASIC TRAMPOLINE BOUNCES
1. Start from standing position, feet shoulder
width apart and with head up and eyes on mat.
2. Swing arms forward and up and around in a
circular motion.
3. Bring feet together while in mid-air and point
toes downward.
4. Keep feet shoulder width apart when landing
on mat.
1. Start with basic bounce and keep it low.
2. Land on knees keeping back straight, body
erect and use your arms to maintain balance.
3. Bounce back to basic bounce position by
swinging arms up.
1. Land in a flat sitting position
2. Place hands on mat besides hips, do not lock
your elbows.
3. Return to erect position by pushing with hands.
1. Start with a low bounce.
2. Land in prone (face down) position and keep
hand and arms extended forward on mat.
3. Push off the mat with arms to return to
standing position.
1. Start with front bounce position.
2. Push off with left or right hands and arms
(depending on which way you wish to turn).
3. Maintain head and shoulders in the same
direction and keep back parallel to mat and
head up.
4. Land in prone position and return to standing
position by pushing up with hands and arms.
WARNING
ALWAYS START YOUR JUMP AT THE CENTER OF THE MAT. WHEN YOU LAND MORE THAN
30 CM AWAY FROM THE LOGO, STOP YOUR JUMP IMMEDIATELY!
RESTART YOUR JUMP AT THE CENTER OF THE MAT.
NOTE
MAKE SURE ALL BUCKLES AND ZIPPERS ARE CORRECTLY CLOSED DURING ANY USE OF
THE TRAMPOLINE.
13

CARE AND MAINTENANCE
This trampoline was designed and manufactured with quality materials and craftsmanship.
If proper care and maintenance is provided, it will provide all jumpers with years of exercise,
fun, and enjoyment as well as reduce the risk of injury. Please follow the guidelines listed below.
Installments of additional accessories must be carried out as per manufacturer’s instructions.
This trampoline is designed to withstand a certain amount of weight and use. Please make sure
that only one person at any one time uses the trampoline. Jumpers should either wear socks,
gymnastics shoes, or be barefoot when using the trampoline. Please be aware that street shoes
or tennis shoes should NOT be worn while using the trampoline. In order to prevent the trampoline
mat from getting cut or damaged please do not allow any pets onto the mat. Also, jumpers should
remove all sharp objects from their person prior to using the trampoline. Any type of sharp or
pointed objects should be kept off the trampoline mat at all times. Regurlarly check that nuts and
bolts are securely tightened, since they may come loose over time. Check that all spring-loaded
(pit pin) joints are still intact and cannot become dislodged during play; Check all coverings and
sharp edges and replace when required Check that mat, padding and enclosure are free from
defects.
Always inspect the trampoline before each use for worn, abused or missing parts. A number of
conditions could arise that may increase your chances of getting injured. Please be aware of:
•Punctures, holes, or tears in the trampoline mat
• Sagging trampoline mat
• Loose stitching or any kind of deterioration of the mat
• Bent or broken frame parts, such as the legs
• Broken, missing, or damaged springs
• Damaged, missing, or insecurely attached frame pad
• Protrusions of any types (especially sharp types) on the frame, springs, or mat
Note. Sunlight, rain, snow and extreme temperatures reduce the strength of these parts over time.
IF YOU FIND ANY OF THE PREVIOUS CONDITIONS, OR ANYTHING ELSE THAT YOU FEEL
COULD CAUSE HARM TO ANY USER, THE TRAMPOLINE SHOULD BE DISASSEMBLED OR
SECURED FROM USE UNTIL THE CONDITION (S) HAS BEEN RESOLVED.
Do not modify the trampoline or any of its parts
The net should for safety’s sake be replaced every year.
MOVING THE TRAMPOLINE
If you need to move the trampoline, two people should be used. All connector points should be
wrapped and secured with weather resistant tape, such as duct tape. This will keep the frame
intact during the move and prevent the connector points from dislocating and separating. When
moving, lift the trampoline slightly off the ground and keep it horizontal to the ground. For any type
of other move, you should disassemble the trampoline.
Keep this instruction manual.
14

90 cm
270 cm
426 cm
Det er meget vigtigt, at du læser og forstår vejledningen, før trampolinen samles og
an-vendes.
Vi håber, at du bliver glad for at bruge trampolinen. En trampolin er rigtig sjov og giver god motion
på samme tid. Det tager lidt tid at samle den, men det er lettere, hvis du læser alle anvisninger,
før du starter. Det kan tage over en time at samle trampolinen, så vær tålmodig, og få en til at
hjælpe dig.
Samlevejledning
JumpXFun Trampolin
Extreme 426cm
–

VIGTIGT
Læs følgende erklæring og advarsler for at undgå alvorlige eller fatale ulykker.
Advarsel.
- Maks. 150 kg.
- Kun til privat brug.
- Til udendørs brug.
- Kun en bruger ad gangen. Risiko for kollision.
- Nettet bør udskiftes hvert år.
- Opsyn af en voksen er påkrævet.
- Lav ikke saltomortaler. Det er meget farligt, og du risikerer alvorlige skader eller dødsfald.
- Luk altid sikkerhedsnettets åbning, inden du begynder at hoppe.
- Læs vejledningen.
- Trampolinen skal samles af en voksen ifølge samlevejledningen og derefter tjekkes før brug.
- Hop kun i gymnastiksko eller med bare fødder.
- Tøm lommerne, og hav ikke noget i hænderne.
- Hop altid på midten af dugen.
- Må ikke bruges, hvis dugen er våd.
- Spis ikke, når du hopper
- Hop aldrig ned fra trampolinen.
- Benyt trampolinen i begrænset tid (hold jævnligt pauser).
- Må ikke bruges i stærk blæst. Fastgør trampolinen.
- Forsøg ikke at springe over nettet.
- Hop ikke ind i nettet med vilje.
- Forsøg ikke at hoppe tilbage fra nettet igen med vilje.
- Hæng ikke oven på nettet, og forsøg ikke at klatre op i det.
- Tag smykker af, som kan vikle sig ind i nettet eller skære i det.
Placering af trampolinen
Placer aldrig trampolinen på et cementgulv eller andre hårde fl der. Den bedste placering er på en jævn
og stabil overflade som for eksempel en græsplæne. Der skal vær et frit område på mindst to meter
omkring trampolinen. Sørg for, at der ikke er nogen ledninger, grene, hegn eller andre mulige farer over
og rundt om trampolinen. Trampolinen må ikke placeres tæt på pools, gynger, rutsjebaner, klatrestativer
eller andre installationer, der udgør en risiko. Denne trampolin er ikke beregnet til nedgravning.
Vejrforhold
Trampolinen må ikke bruges, når den er våd. Skil trampolinen ad om vinteren, og opbevar alle
stofdele (dug, skumkanter og sikkerhedsnet) indendørs. Fjern skumkanter og sikkerhedsnet ved
stærk blæst, og fastgør trampolinen til jorden med pløkker/jordspyd (sælges separat).
Vejledning
Start langsomt. Forsøg ikke at lave svære øvelser.
Hop ikke i trampolinen, når du er træt. Det øger risikoen for skader. Sørg for at bære passende
fodtøj, f.eks. gymnastiksko, eller hop med bare fødder.
Træd aldrig på sikkerhedsbetrækket. Det er ikke konstrueret til at kunne bære en persons vægt.
Når du skal ned fra trampolinen, må du aldrig hoppe. Kravl altid af. Hop aldrig i trampolinen, hvis
du har indtaget stoffer eller alkohol.
Der skal altid være andre til stede, når du hopper i trampolinen. Så er der nogen til at hjælpe dig,
hvis du skulle komme til skade.
Begynd altid med at hoppe midt i cirklen. Hvis du lander mere end 30 cm fra kanten af logoet, skal
du omgående holde op med at hoppe!
Begynd at hoppe på midten af dugen igen.
Montering
Læs samlevejledningen omhyggeligt, før du begynder at samle trampolinen. Det kan anbefales, at
to personer hjælpes ad med at samle trampolinen.
Begynd med at kontrollere, at du har alle de nødvendige dele. Hver dels referencenummer vil
blive brugt her i vejledningen som en hjælp til dig.
16

Delnr. Dele Beskrivelse Antal
1Trampolindug med påsyede
trekantringe 1
2 Sikkerhedsbetræk 1
3 Topramme med benfæster 6
4 Topramme 6
5 Benbase 6
6 L-formet ben 12
7Galvaniserede fjedre
(3,5mm x 34N) 84
8 Fjedermonteringsværktøj 1
9 Buet spændeskive 12
10 Skrue 12
11 Unbrakonøgle 1
12 Fjederskive 12
13 Selvlåsende skrue (lille) 12
Oversigt over dele (trampolin):
17

Delnr. Dele Beskrivelse Antal
AØvre rammerør med langt
skumstykke 6
BMidterste rammerør med kort
skumstykke 6
C Nedre rammerør uden skumstykke 6
D U-skrue 12
E Spændebånd 12
F Låsemøtrik 24
G Afstandsstykke 12
H Selvlåsende skrue 18
I Kabeltråd 12
J Plastikhætte 6
K Line 9
L Sikkerhedsnet 1
M Møtrikhætte 24
N Skruenøgle 1
O PVC-muffe 6
P Kasket 6
Q Endestykke 6
Oversigt over dele (sikkerhedsnet):
18

6
6
5
3
4
Montering af trampolin
Der skal to personer til at montere trampolinen.
Trin 1
Start med at bygge rammen. Skub delene sammen.
Begynd med at lægge delene ud som vist på billedet.
Trin 2
Før to L-formede ben 6 ind i benbasen 5 som vist. Gentag for at alle benbaserne. Stram med
skruen 10 og den buede spændeskive 9 .
6 6
10 5
9
19

12 13
11
Trin 3
Tag den benstøtte, som du samlede i trin 2. Her er det lettest, hvis en person holder benstøtten,
og en anden person sætter toprammen med benfæster” 3 på plads som vist på billedet. Gentag
dette for alle ben.
Indsæt nu de resterende toprammer 4 i hullerne mellem benstøtterne som vist.
Skru den selvlåsende skrue (lille) 13 og fjederskiven 12 på som vist. Stram dem ikke på
nuværende tidspunkt.
5
6 6
3
6 6
5
4
6
3
666
12
12
20