Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are
trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies
in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof might be covered by one or more
of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899,
6,552,918, 6,567,902, 6,578,186, and 6,590,785. Copyright © 2016 Juniper Networks, Inc. All rights reserved. Printed in Malaysia. Part Number: 530-067368 Revision 01, 1 April 2016.
6. Repeat the steps for each power supply you are connecting.
7. Insert the power cord plug into an AC power source outlet.
NOTE: The optical ILA powers on as soon as power is provided to the power supply.
8. If the AC power source outlet has a power switch, set it to the on (|) position.
9. Verify that the status LED for each power supply is lit green and is on steadily.
Part 3: Perform the Initial Configuration
You must perform the initial configuration of the optical ILA through the console port.
Before you begin, set the following parameter values from the console server or PC:
zBaud Rate—115200
zFlow Control—None
zData—8
zParity—None
zStop Bits—1
zDCD State—Disregard
To connect and configure the optical ILA from the console:
1. Connect the console port to a laptop or PC by using the provided RJ-45 cable and
RJ-45 to DB-9 serial port adapter. The console (CON) port is located on the
management panel of the optical ILA.
2. Log in as the root user. Enter the default password root.
login: root
3. Start the command-line interface (CLI).
root@% localhost:~# /usr/bin/command
Welcome to ILA World
BPS>
4. To enter the administrative mode, log in as the root user with password Admin@123.
BPS>login
Username: root
Password: *********
Completed!
BPS>
5. You can use the CLI commands documented in the Optical Inline Amplifier Hardware
Guide to configure, monitor, and troubleshoot the optical ILA.
Safety Warnings Summary
This is a summary of safety warnings. For a complete list of warnings, including
translations, see the optical ILA documentation at http://www.juniper.net/techpubs/.
WARNING: Failure to observe these safety warnings can result in personal injury
or death.
zOnly trained and qualified personnel are permitted to install or replace the optical ILA
components.
zPerform only the procedures described in this quick start and the optical ILA
documentation. Other services must be performed by authorized service personnel.
zBefore installing the optical ILA, read the planning instructions in the optical ILA
documentation to make sure that the site meets power, environmental, and clearance
requirements for the optical ILA.
zBefore connecting the optical ILA to a power source, read the installation instructions
in the optical ILA documentation.
zIf the rack or cabinet has stabilizing devices, install them in the rack before mounting or
servicing the optical ILA in the rack or cabinet.
zBefore installing or after removing an electrical component, always place it
component-side up on a flat antistatic mat or in an antistatic bag.
zDo not work on the optical ILA or connect or disconnect cables during electrical
storms.
zBefore working on equipment that is connected to power lines, remove jewelry,
including rings, necklaces, and watches. Metal objects heat up when connected to
power and ground and can cause serious burns or become welded to the terminals.
Contacting Juniper Networks
For technical support, see:
http://www.juniper.net/support/requesting-support.html
