JVC EverioR GZ-R428 User manual

Read Me First
CAMCORDER
GZ-R428 E
Dear Customers
Thank you for purchasing this JVC product.
Before use, please read the “Read Me First” to ensure safe use of this product.
Verifying the Accessories
0AC Adapter (UIA312-0520)
0Power Cord
0Adapter Cable
0USB Cable (Type A - Micro Type B)
0AV Cable (E3A-0085-00)
0Core Filter (for AV Cable)
0Lens Cap
0Read Me First (this booklet)
B5A-2277-00
EN
.
Detailed User Guide
For more details on operating this
product, please refer to the “Detailed
User Guide” at the following website.
http://manual3.jvckenwood.com/index.html/
.Mobile User Guide
When you are outside, refer
to the “Mobile User Guide”.
Mobile User Guide can be
viewed with standard
browser for Android tablet
and iPhone.
http://manual3.jvckenwood.com/mobile/asia/

Safety Precautions
CAUTIONS:
0
If you notice smoke or a peculiar smell
coming from this unit or AC Adapter, shut
it down and unplug it immediately.
Continue using the unit or AC Adapter
under these conditions could lead to fire
or electric shock. Contact your JVC
dealer. Do not attempt to repair the
malfunction yourself.
0
To prevent shock, do not open the
cabinet. No user serviceable parts
inside. Refer servicing to qualified
personnel.
0
When you are not using the AC adapter
for a long period of time, it is
recommended that you disconnect the
power cord from AC outlet.
0
In certain areas, use the conversion plug
depending on the type of your AC wall
outlet.
NOTES:
0
The rating plate and safety caution are
on the bottom and/or the back of the main
unit.
0
The serial number plate is on the battery
pack mount.
0
The rating information and safety caution
of the AC adapter are on its upper and/
or lower sides.
WARNING:
The camcorder with battery installed
should not be exposed to excessive heat
such as direct sunlight, fire or the Iike.
CAUTION:
The mains plug shall remain readily
operable.
0
Remove the mains plug immediately if
this unit functions abnormally.
CAUTION:
To avoid electric shock or damage to the
unit, first firmly insert the small end of the
power cord into the AC Adapter until it is
no longer wobbly, and then plug the larger
end of the power cord into an AC outlet.
.
CAUTION:
A built-in lithium-ion battery is inside the
unit. When discarding the unit,
environmental problems must be
considered and the local rules or laws
governing the disposal of these batteries
must be followed strictly.
CAUTIONS:
0
Be sure to use the supplied AC adapter.
0
Do not use the supplied AC adapter with
other devices.
2EN

Do not point the lens directly into the sun.
This can cause eye injuries, as well as
lead to the malfunctioning of internal
circuitry. There is also a risk of fire or
electric shock.
CAUTION!
The following notes concern possible
physical damage to this unit and to the
user.
Carrying or holding this unit by the LCD
monitor can result in dropping the unit, or
in a malfunction.
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the unit.
CAUTION!
Connecting cables (Audio/Video, etc.) to
this unit and leaving it on top of the TV is
not recommended, as tripping on the
cables will cause this unit to fall, resulting
in damage.
Make a backup of important recorded
data
JVC will not be responsible for any lost
data. It is recommended to copy your
important recorded data to a disc or other
recording media for storage once every 3
months.
.
If this symbol is shown, it is only valid in
the European Union.
This product is licensed under the AVC
Patent Portfolio License for the personal
use of a consumer or other uses in which
it does not receive remuneration to (i)
encode video in compliance with the AVC
standard (“AVC Video”) and/or (ii) decode
AVC Video that was encoded by a
consumer engaged in a personal activity
and/or was obtained from a video provider
licensed to provide AVC Video. No
license is granted or shall be implied for
any other use.
Additional information may be obtained
from MPEG LA, L.L.C.
See http://www.mpegla.com
oAttaching the Core Filter
Attach the core filter to the AV Cable as shown in the illustration. The core filter reduces
interference when this unit is connected to other devices.
.
3 cm
To be connected to this unit
Release the
stopper.
Wind once
EN 3

Built-in Battery
This unit is equipped with a built-in lithium-
ion battery. Before using this Unit, be sure to
read the following cautions:
0
To avoid hazards
…
do not burn.
…
do not modify or disassemble.
…
do not expose this Unit to temperatures
exceeding 60 °C, as this may cause the
built-in battery to overheat, explode or
catch fire.
0
To prevent damage and prolong
service life
…
do not subject to unnecessary shock.
…
charge within the temperature range of
10°C to 35°C. Cooler temperatures require
longer charging time, or in some cases
stop charging at all.
Warmer temperatures prevent complete
charging, or in some cases stop charging
at all.
…
store in a cool, dry place. Extended
exposure to high temperatures will
increase natural discharge and shorten
service life.
…
keep a 30% battery level ( i ) if the
battery is not to be used for a long period
of time.
In addition, fully charge and then fully
discharge the battery every 6 months, then
continue to store it at a 30% battery level
(
i ).
…
remove the AC adapter from the unit when
not in use, as some machines use current
even when switched off.
…
do not drop intentionally or subject to
strong impact.
Recording Medium
0
Be sure to follow the guidelines below
to prevent corruption or damage to
your recorded data.
0
Do not bend or drop the recording
medium, or subject it to strong pressure,
jolts or vibrations.
0
Do not splash the recording medium
with water.
0
Do not use, replace, or store the
recording medium in locations that are
exposed to strong static electricity or
electrical noise.
0
Do not bring the recording medium near
objects that have a strong magnetic field
or that emit strong electromagnetic
waves.
0
Do not store the recording medium in
locations with high temperature or high
humidity.
0
Do not touch the metal parts.
0
When erasing data using the camcorder,
the data won’t be erased completely.
When handing over your camcorder and/
or SD card, you are recommended to erase
all of the data by either performing
“FORMAT” or “FACTORY PRESET”
operation on this unit, using commercially
available software, or by physically
destroying the camcorder.
LCD Monitor
0
To prevent damage to the LCD monitor,
DO NOT
…
push it strongly or apply any shocks.
…
place the camcorder with LCD monitor on
the bottom.
0
To prolong service life
…
avoid rubbing it with coarse cloth.
While the LCD monitor screen has more
than 99.99% effective pixels, 0.01% of the
pixels may be bright spots (red, blue,
green) or dark spots. This is not a
malfunction. The spots will not be
recorded.
4EN

Main Unit
0
For safety, DO NOT
…
open the camcorder’s chassis.
…
disassemble or modify the unit.
…
allow inflammables, water or metallic
objects to enter the unit.
…
disconnect the power supply while the
power is on.
…
place naked flame sources, such as
lighted candles, on the apparatus.
…
leave dust or metal objects adhered to the
power plug or an AC wall outlet.
…
insert any objects in the camcorder.
0
Avoid using the unit
…
in places subject to soot or steam such as
near a cooking stove.
…
in places subject to excessive shock or
vibration.
…
near a television set.
…
near appliances generating strong
magnetic or electric fields (speakers,
broadcasting antennas, etc.).
…
in places subject to extremely high (over
40 °C) or extremely low (under -10 °C)
temperatures.
0
DO NOT leave the unit
…
in places of over 50°C
…
in places where humidity is extremely low
(below 35 %) or extremely high (above 80
%) with the terminal cover open.
…
in direct sunlight.
…
in a closed car in summer.
…
near a heater.
…
in high places such as on a TV. Leaving the
unit in high places while a cable is
connected may result in a malfunction if the
cable is caught and the unit falls onto the
floor.
0
To protect the unit, DO NOT
…
drop the unit or strike it against hard
objects.
…
subject it to shock or excessive vibration
during transportation.
…
keep the lens directed at extremely bright
objects for long periods.
…
expose the lens to direct sunlight.
…
swing it excessively when using the hand
strap.
…
swing the soft camcorder case excessively
when the camcorder is inside it.
…
cover camcorder with a towel, cloth and so
on.
0
To prevent the unit from dropping
0
Fasten the grip belt securely.
0
When using the camcorder with a tripod,
attach the camcorder to the tripod
securely.
If the camcorder drops, you may be injured
and the camcorder may be damaged.
When a child uses the unit, there must be
parental guidance.
Power Consumption
0
2.2 W (when [MONITOR BRIGHTNESS]
is set to [3] (standard))
0
Rated Current Consumption: 2A
EN 5

.
This unit is equipped with Water
proof, Dust proof, Drop proof and
Freeze proof.
Water proof: Equivalent to IEC
Standard publication 529 IPX8
and IPX6 (30 minutes at depths
up to 5 m)
Dust proof: Equivalent to IEC
Standard publication 529 IP5X
Drop proof: This camera
clears company testing
compliant with "MIL-
STD-810F Method; 516.5
Shock: dropping onto
plywood 3 cm thick from a
height of 1.5 m"
Freeze proof: Allowable
operating temperatures: −10 °C
to +40 °C
Note: Temperatures between
−10 °C and 0 °C temporarily
lower battery performance,
reducing the time available for
recording.
Before use in water, be sure to read and
understand the “Detailed User Guide”.
Precautions for waterproof function
0
Malfunction due to misuse by the
customer is not covered by warranty.
0
Close the terminal cover firmly until it
clicks and confirm that the red sign
completely goes off.
0
Make sure that there is no damage to and
no foreign material adhered to the
packing inside the cover.
0
Use the camcorder in marine water and
fresh water not deeper than 5 m or for not
more than 30 minutes.
0
The waterproof cannot be guaranteed if
the camcorder is subject to impact such
as dropping.
0
Do not jump or dive into water holding the
camcorder.
0
Do not use the camcorder in strong water
flows such as in rapids or under
waterfalls. The strong water pressure
may impair the waterproof performance.
0
Do not soak the camcorder in hot springs
or water of 40 °C or higher.
Remember that this unit is intended
for private consumer use only.
Any commercial use without proper
permission is prohibited. (Even if you
record an event such as a show,
performance or exhibition for personal
enjoyment, it is strongly recommended
that you obtain permission
beforehand.)
Trademarks
0
AVCHD and AVCHD logo are
trademarks of Panasonic Corporation
and Sony Corporation.
0
AVCHD progressive and AVCHD
progressive logo are trademarks of
Panasonic Corporation and Sony
Corporation.
0
HDMI (High-Definition Multimedia
Interface) and HDMI logo are either
registered trademarks or trademarks
of HDMI Licensing, LLC in the United
States and/or other countries.
.
0
Manufactured under license from
Dolby Laboratories. Dolby and the
double-D symbol are trademarks of
Dolby Laboratories.
0
SDXC logo is a trademark of SD-3C LLC.
0
Windows® is either registered
trademark or trademark of Microsoft
Corporation in the United States and/
or other countries.
0
Apple, Mac, Mac OS, OS X, iMovie,
iPhoto, iPhone and Safari are
trademarks of Apple Inc., registered in
the U.S. and other countries.
0
Intel and Intel Core are trademarks or
registered trademarks of Intel
Corporation or its subsidiaries in the
United States and other countries.
0
Google™, Android™, YouTube™,
YouTube logo and Chrome™ are
trademarks and/or registered
trademarks of Google Inc.
6EN

Fogging inside the Lens
Models with waterproof function are airtight.
When the temperature rises during
recording, condensation can occur inside
the lens due to the internal humidity.
During recording
To prevent the temperature of this unit from
rising, we recommend that you use the unit
in the following ways.
A
Avoid frequent exposure to direct
sunlight.
Record under the shade or use an
umbrella. Best if you could keep a wet
towel cover the unit.
B
The use of a tripod is recommended.
Long hours of recording while holding the
unit in your hands will cause the
temperature of the unit to rise.
C
It is better to leave the terminal cover open
while recording.
However, the waterproof, dust-proof and
shockproof features do not function in this
condition. Do take note of the environment
when using the camera. (Do not use a wet
towel.)
D
Make sure to turn off the power when you
are not recording.
The power turns off when the LCD monitor
is closed.
During charging
It is recommended to charge the unit in a low
humidity environment.
The moist air inside the unit can cause
condensation.
We recommend that you charge the unit in a
room where humidifier is not in use, and in
an air-conditioned room during summer.
When fogging occurs inside the lens
Open the terminal cover to reduce the
temperature, close the LCD monitor and
leave the camera as it is for a while.
.
Open the terminal cover.
Protecting the Lens
This unit does not come with a lens cover and
lens cap.
However, there is a protective glass in front
of the lens to protect the lens.
0
It is recommended to put the camera in a
cloth bag when carrying it around.
0
If the protective glass is dirty, wipe clean
using a commercially available cleaning
cloth.
.
Lens protective glass
EN 7

.
.
.
.
©2017 JVC KENWOOD Corporation AH 0717TOH-SW-MT

用前必读
摄像机
GZ-R428 E
尊敬的顾客
感谢您购买此 JVC 产品。
使用之前，请阅读“用前必读”以确保安全使用本产品。
核对附件
0交流电适配器（UIA312-0520）
0电源线
0适配器电缆
0
USB 电缆（Type A - Micro Type B）
0AV 电缆（E3A-0085-00）
0核心过滤器（用于 AV 电缆）
0镜头盖
0用前必读（本手册）
B5A-2277-00
CS
.
详细用户使用指南
如需有关如何操作本产品的更多信息，请
访问以下网站的“详细用户使用指南”。
http://manual3.jvckenwood.com/index.html/
.移动用户指引
在户外时，请参阅“移动
用户指引”。可通过
Android tablet 和iPhone
的标准浏览器查看移动用
户指引。
http://manual3.jvckenwood.com/mobile/asia/

安全注意事项
警告 ：
0
若发现摄像机或交流电源适配
器发出烟雾或异味，应立即关闭
电源，或者拔下电源插头。如果
此时继续使用本摄像机或交流
电源适配器，将会导致火灾或电
击。请与 JVC 经销商联系。切勿
尝试自行修复。
0
为预防电击，请勿擅自打开机
壳。机内无用户可修的零件。检
修时请找特约技术人员。
0
在您长时间不用交流电源适配
器时，建议您从交流电源插座上
拔下电源电线。
0
在某些地区，请根据交流电源墙
壁插座的类型使用转换插头。
注意 ：
0
额定值牌（系列号码牌）和安全
警告位于主机的底部和/或背面
上。
0
序列号码牌在电池箱座上。
0
交流电适配器的额定信息和安
全警告位于其上部和/或下部。
小心 ：
请勿将装有电池的摄像机暴露于
直射阳光、火焰或类似高温环境
下。
小心 ：
电源插头应易于操作。
0
如果摄像机功能异常，请立即拔
下电源插头。
小心 ：
为防电击或损坏本机，先将电源
电线的小头紧紧插入交流电源适
配器直到不再松动，然后将电源
电线的大头插入交流电源插座。
.
小心 ：
本机内装有内置锂离子电池。处
理本机时，应充分考虑环境问题。
请务必严格遵守当地有关此类电
池处理的规定或法律。
警告 ：
0
务必使用随附的交流电适配器。
0
不要在其它设备上使用附带的
交流适配器。
2CS

不要将镜头直接对向太阳。否则
会损伤眼睛并导致内部电路出现
故。还可能有引起火灾或电击的
危险。
警告!
下列注意事项关系到对摄像机及
用户的可能损害。
抓着液晶监视器携带或拿持摄像
机会摔落本机，或引起故障。
不要在不平稳的平面上使用三脚
架。否则可能翻倒而使摄像机严
重受损。
警告!
最好不要把摄像机接在电缆（音
频/视频、等）上然后将本机放在电
视机顶面上，否则不小心勾到电
缆则会使摄像机摔落而受损。
给重要的录制数据做好备份
JVC 对丢失的数据概不负责。 建
议您每三个月把重要的录制数据
复制到光碟或其他录制媒体上存
储。
.
如果显示此符号，仅在欧盟国家
有效。
本产品根据 AVC 专利组合许可
授权，供消费者个人使用或用于
不获得酬劳的以下用途（i）按照
AVC 标准进行视频编码（“AVC
视频”）和/或（ii）对 AVC 视频进
行解码，该视频是由从事个人活
动的消费者进行编码和/或从已获
AVC 视频提供许可的视频提供商
处获得。未授予或暗示任何其他
用途的许可。
可通过 MPEG LA、L.L.C.获得更
多信息
请访问 http://www.mpegla.com
o连接核心过滤器
如图所示，把核心过滤器安装至 AV 电缆。 本机与其他设备相连时，核
心过滤器会减少干扰。
.
3 cm
㚊⼆ᶏ㚭㚻彟㌦
㛿⺁撂㇤ɝ 乖ᶁ⚉
CS 3

内置电池
本机装备有内置锂离子电池。在使
用本机前，请务必阅读以下注意事
项：
0
为避免危险
…
请勿燃烧。
…
请勿修改或拆解。
…
请勿将本机暴露在温度超过 60℃
的环境中，否则可能引起内置电
池过热、爆炸或着火。
0
为避免毁坏并延长使用寿命
…
避免不必要的震动。
…
请在 10℃至 35℃的温度范围内
进行充电。低温需要较长时间充
电，某些情况下会完全停止充电。
高温会导致无法完全充电，某些情
况下会完全停止充电。
…
在凉爽干燥的地方保存。长时间
暴露在高温下会引起自然放电，
并缩短使用寿命。
…
如果电池长期不用，则保持 30 %
（ i ）的电量。
此外，每 6个月把电池充足电，然
后完全放电，再继续保持 30 %
（
i ）的电量。
…
将交流电适配器从未使用的机器
中取出，因为某些设备即使是在
关机的状态下也会有电流。
…
不要故意掉落或使其受到强烈撞
击。
记录媒体
0
请务必遵循以下指南，以免损坏
记录的数据。
0
请勿弯折或掉落记录媒体，或
让其经受强烈压力、冲击或振
动。
0
请勿将水洒到记录媒体上。
0
请勿在有强烈静电或电气噪声
的地方使用、更换或贮存记录
媒体。
0
请勿将记录媒体放在有强烈磁
场或释放强烈电磁波的物体附
近。
0
请勿将记录媒体存放在高温或
高湿的地方。
0
请勿触摸金属部件。
0
在使用摄像机删除数据时，数据
不会被完全删除。在处理您的摄
像机和/或SD 卡时，建议您通过
以下手段之一删除所有数据：在
本机上执行“格式化”或“出厂前
预设值”操作，使用市售软件，或
者实际上毁坏摄像机。
液晶监视器
0
为防止液晶监视器损坏，请勿
…
用强力推入或振动。
…
放置摄像机时将液晶监视器置于
底部。
0
为了延长使用寿命
…
避免使用粗布擦拭。
尽管液晶监视器的屏幕可能有
99.99 %以上的有效像素，但 0.01
%的像素可能是亮点（红、蓝、绿）
或黑点。 这不是故障。 这些点不
会录进去。
4CS

主机
0
为保证安全，请勿
…
打开摄像机底盘。
…
拆解或修改设备。
…
让易燃物、水或金属物体进入设
备。
…
在开机状态下断开电源。
…
将本机靠近明火，如点燃的蜡烛
等。
…
使电源插头或交流电源插座沾附
灰尘或金属物体。
…
将异物插入摄像机。
0
避免在以下地方使用设备
…
有烟灰或蒸汽的地方，例如靠近
厨灶的地方。
…
振动或抖动过大的地方。
…
靠近电视机。
…
靠近产生强磁场或强电场的地方
（扬声器、广播天线等）。
…
放置于温度过高（超过 40℃）或过
低（低于-10℃）的地方。
0
请勿将设备放在
…
超过 50℃的地方。
…
在端子盖敞开的状态下放置于湿
度过低（35 %以下）或过高（80 %
以上）的地方。
…
阳光直射下。
…
夏季时封闭汽车内。
…
靠近加热器的地方。
…
电视机等高处。在连接了电缆的
情况下将设备放置于高处时，如
果绊到电缆且主机跌落到地面，
则可能导致故障。
0
为保护设备，请勿
…
摔落设备或将其撞击硬物。
…
在运输过程中振动或过度抖动。
…
长时间使镜头直接对着过亮的物
体。
…
将镜头暴露于直射阳光。
…
使用手带时猛烈摇晃。
…
过度摇晃装有摄像机的摄像机
包。
…
用毛巾、布等物品盖住摄像机。
0
为防止本机跌落
0
扣紧手握带。
0
使用三脚架时，请将摄像机牢
固地安装在三脚架上。
如果摄像机跌落，可能会使您受到
伤害，摄像机也可能会受到损坏。
儿童务必在家长的监护下使用该设
备。
电源消耗
0
2.2 W（将[监视器亮度]设为时[3]
（标准））
0
额定电流消耗 ：2A
CS 5

.
本机配备有防水、防尘、防跌落和
防冻功能。
防水：相当于 IEC Stand-
ard publication 529 IPX8
和 IPX6（深达 5米的水中
30 分钟）
防尘：相当于 IEC Stand-
ard publication 529 IP5X
防跌落：该摄像机高于符
合“MIL-STD-810F 方法的
公司测试标准；516.5 冲
击：从 1.5 米高处掉落在 3
厘米厚的胶合板上”
防冻：允许的工作温
度：-10°C 至+40°C
注意：介于−10°C 和 0°C
之间的温度会暂时性地降
低电池性能，并因此减少可
供录制的时间。
在于水中使用以前，请确保阅读并理
解“详细用户使用指南”。
使用防水功能的注意事项
0
由于顾客使用不当所造成的故障
不在保修范围内。
0
紧紧关上端子盖直至其卡住，并
确认红色标志完全熄灭。
0
请确保盖内的包装上无损伤并且
没有附着异物。
0
在不超过 5米深的海水及淡水中
使用摄像机，或者在水中使用不
超过 30 分钟。
0
如果摄像机受到如跌落等撞击，
则防水功能无法得到保证。
0
在持有摄像机时，请勿跳入或潜
入水中。
0
请勿在强水流如激流中或瀑布下
使用摄像机。强大的水压可能会
影响防水性能。
0
请勿将摄像机浸于温泉中或者温
度为 40 °C 或更高的水中。
记住，本摄像机仅供用户个人使用。
任何未经许可的商业使用都是受禁止
的。（即使是摄录个人欣赏用的影片、
表演或展览，您最好事先获得准许。）
商标
0
AVCHD 和AVCHD 徽标是
Panasonic Corporation 和
Sony Corporation 的商标。
0
AVCHD progressive 和
AVCHD progressive 徽标是
Panasonic Corporation 和
Sony Corporation 的商标。
0
HDMI（高清多媒体接口）和
HDMI 徽标是 HDMI Licens-
ing, LLC 在美国和/或其他国家
的注册商标或商标。
.
0
经Dolby Laboratories 许可制
造。“Dolby”和双 D标志是
Dolby Laboratories 的商标。
0
SDXC 徽标是 SD-3C LLC 的
商标。
0
Windows®是Microsoft Cor-
poration 在美国和/或其他国家
的注册商标或商标。
0
Apple、Mac、Mac OS、OS X、
iMovie、 iPhoto、iPhone 和 Sa-
fari 是苹果公司在美国和其他
国家的商标。
0
Intel 和Intel Core 是英特尔公
司或其在美国和其他国家的子
公司的商标或注册商标。
0
Google™、Android™、 You-
Tube™、 YouTube 徽标和
Chrome™是谷歌公司的商标
和/或注册商标。
6CS

镜头内部起雾
备有防水功能的型号具有密封性。
当温度在录制过程中升高时，摄像
机内部的湿度会导致镜头内部起雾
（冷凝）。
录制期间
为防止本机温度升高，建议您按照
以下方式使用本机。
A
避免经常暴露于阳光直射下。
在阴影处或打伞拍摄。最好能用
湿毛巾盖住本机。
B
建议使用三脚架。
手持本机进行长时间拍摄会导致
本机温度升高。
C
最好在拍摄时将端子盖敞开。
但是，在这种状态下防水、防尘和
防震功能无法工作。使用摄像机
时，请注意周围环境。（不要使用
湿毛巾。）
D
不进行录制时，务必切断电源。
液晶监视器关闭时，电源也随之
切断。
充电期间
建议在低湿度环境下进行充电。
本机内部的湿气会导致冷凝。
建议您在没有使用加湿器的房间进
行充电；夏季则在空调房间进行充
电。
当镜头内部起雾时
打开端子盖降低温度，关闭液晶监
视器并将摄像机放置片刻。
.
㇔⺁䩰⫑䙗ɝ
保护镜头
本机没有配备镜头盖。
然而，镜头前方的防护玻璃可以保
护镜头。
0
建议随身携带摄像机时，将其放
进一个布袋里。
0
如果防护玻璃脏了，请使用市售
清洁布擦拭。
.
擝⢵斳㈥䌼䐄
CS 7

.
.
.
.
©2017 JVC KENWOOD Corporation AH 0717TOH-SW-MT