JVC KD-G161 User manual

ENGLISH
FRANÇAIS
CD RECEIVER
RECEPTEUR CD
KD-G162/KD-G161
For installation and connections, refer to the separate manual.
Pour l’installation et les raccordements, se référer au manuel séparé.
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
GET0334-003A
[EX/EU]
For canceling the display demonstration, see page 5.
Pour annuler la démonstration des affichages, référez-vous à la page 5.
KD-G162
KD-G161
KD-G162
KD-G161
Cover_KD-G162_161[EX_EU]f.indd 2Cover_KD-G162_161[EX_EU]f.indd 2 10/18/05 4:47:11 PM10/18/05 4:47:11 PM

2
ENGLISH
How to detach/attach the control
panel
Detaching...
Attaching...
Note: Only for [EX] model users in UK and
European countries
For security reasons, a numbered ID card
is pro ided with this unit, and the same ID
number is imprinted on the unit’s chassis.
Keep the card in a safe place, as it will help the
authorities to identify your unit if stolen.
Warning:
If you need to operate the unit while dri ing,
be sure to look ahead carefully or you may be
in ol ed in a traffic accident.
How to reset your unit
• Your preset adjustments will also be erased.
How to forcibly eject a disc
• If this does not work, reset your unit.
• Be careful not to drop the disc when it ejects.
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to
obtain the best possible performance from the unit.
IMPORT NT FOR L SER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top co er. There are no user ser iceable parts inside the unit; lea e
all ser icing to qualified ser ice personnel.
3. CAUTION: Visible and in isible laser radiation when open and interlock failed or defeated.
A oid direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
EN02-05_KD-G162_1[EX_EU]f.indd 2EN02-05_KD-G162_1[EX_EU]f.indd 2 10/18/05 4:45:06 PM10/18/05 4:45:06 PM

ENGLISH
3
How to read this manual
• Button operations are mainly explained with
the illustrations in the table below.
• is used to indicate an indicator is
displayed for the correspnding operation.
• Some related tips and notes are explained in
“More about this unit” (see pages 14 and 15).
Press briefly.
Press repeatedly.
Press and hold until your
desired response begins.
Press and hold both
buttons at the same time.
How to use the M MODE button
If you press M MODE, the unit goes into
functions mode, then the number buttons work
as different function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
To use these buttons for their original
functions again after pressing M MODE, wait
for 5 seconds without pressing any of these
buttons until the functions mode is cleared or
press M MODE again.
CONTENTS
Control panel — KD-G162 and KD-G161 ........ 4
Getting started ................................. 5
Basic operations .................................................... 5
Radio operations .............................. 6
FM RDS operations ............................ 7
Searching for your favorite FM RDS programme ... 7
Disc operations ................................. 9
Playing a disc in the unit ...................................... 9
Sound adjustments ........................... 10
General settings — PSM ................... 11
Maintenance .................................... 13
More about this unit ......................... 14
Troubleshooting ............................... 16
Specifications ................................... 17
Caution on volume setting:
Discs produce ery little noise compared
with other sources. Lower the olume
before playing a disc to a oid damaging
the speakers by the sudden increase of the
output le el.
For safety...
• Do not raise the olume le el too much, as
this will block outside sounds, making dri ing
dangerous.
• Stop the car before performing any
complicated operations.
Temperature inside the car...
If you ha e parked the car for a long time in hot
or cold weather, wait until the temperature in
the car becomes normal before operating the
unit.
ime countdown indicator
Press either
one.
EN02-05_KD-G162_1[EX_EU]f.indd 3EN02-05_KD-G162_1[EX_EU]f.indd 3 10/18/05 4:45:09 PM10/18/05 4:45:09 PM

4
ENGLISH
Control panel — KD-G612/KD-G611/KD-G511
i M MODE button
o (control panel release) button
Display window
;DISC indicator
a RND (disc random) indicator
s RPT (repeat) indicator
d LOUD (loudness) indicator
f EQ (equalizer) indicator
g Sound mode (C-EQ: custom equalizer)
indicators—JAZZ, CLASSIC, HIP HOP,
POPS, ROCK, USER
h Source display / Volume le el indicator /
Time countdown indicator
j Main display
k RDS indicators—TP, PTY, AF, REG
l Tuner reception indicators—ST (stereo),
MO (monaural)
Parts identification
Display window
Control panel — KD-G162 and KD-G161
1 (standby/on/attenuator) button
2 SOURCE button
3 BAND button
4 Loading slot
5 Display window
6 0 (eject) button
7 TP/PTY (traffic programme/programme
type) button
8 ¢/4 buttons
9 Control dial
p SEL (select) button
q DISP (display) button
w EQ (equalizer) button
e MO (monaural) button
r SSM (Strong-station Sequential Memory)
button
t Number buttons
y RPT (repeat) button
u RND (random) button
EN02-05_KD-G162_1[EX_EU]f.indd 4EN02-05_KD-G162_1[EX_EU]f.indd 4 10/18/05 4:45:10 PM10/18/05 4:45:10 PM

ENGLISH
5
Basic settings
• See also “General settings — PSM” on pages
11 and 12.
1
2
1 Canceling the display
demonstrations
Select “DEMO,” then “DEMO OFF.”
2 Setting the clock
Select “CLOCK H” (hour), then adjust
the hour.
Select “CLOCK M” (minute), then
adjust the minute.
Select “24H/12H,” then “24H” (hour) or
“12H” (hour).
3 inish the procedure.
To check the current clock time while...
The power is turned off
Listening to...
An FM (non-RDS) or AM station:
Frequency Ô Clock
An FM RDS station:
Station name (PS) = Station Frequency =
Programme type (PTY) = Clock = (back to
the beginning)
Listening to a disc...
Elapsed playing time
with track number Ô
Clock
Getting started
Basic operations
~ Turn on the power.
Ÿ
* You cannot select “DIS ” as the
playback source if there is no disc in
the unit.
or M/AM tuner
⁄ Adjust the volume.
Volume level appears.
Volume level indicator
@ Adjust the sound as you want. (See
page 10.)
To drop the volume in a
moment ( TT)
To restore the sound,
press it again.
To turn off the power
EN02-05_KD-G162_1[EX_EU]f.indd 5EN02-05_KD-G162_1[EX_EU]f.indd 5 10/18/05 4:45:11 PM10/18/05 4:45:11 PM

6
ENGLISH
When an FM stereo broadcast is hard to
receive
Lights up when monaural mode is activated.
Reception improves, but stereo effect will be
lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO
indicator goes off.
Storing stations in memory
You can preset si stations for each band.
FM station automatic presetting —
SSM (Strong-station Sequential
Memory)
1 Select the FM band (FM1 – FM3) you
want to store into.
2
3
“SSM” flashes, then disappears when
automatic presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM
band.
Radio operations
~
Ÿ
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Selected band appears.
! Start searching for a station.
When a station is received,
searching stops.
To stop searching, press the
same button again.
To tune in to a station manually
In step ! above...
1
2 Select the desired station fre uencies.
EN06-11_KD-G162_1[EX_EU]f.indd 6EN06-11_KD-G162_1[EX_EU]f.indd 6 10/18/05 4:45:20 PM10/18/05 4:45:20 PM

7
ENGLISH
Manual presetting
E .: Storing FM station of 92.5 MHz into preset
number 4 of the FM1 band.
1
2
3
Preset number flashes for a while.
Listening to a preset station
1
2 Select the preset station (1 – 6) you
want.
FM RDS operations
What you can do ith RDS
RDS (Radio Data System) allows FM stations
to send an additional signal along with their
regular programme signals.
By receiving the RDS data, this unit can do the
following:
• Programme Type (PTY) Search (see the
following)
• TA (Traffic Announcement) and PTY
Standby Receptions (see pages 8 and 12)
•
Tracing the same programme automatically
—Network-Tracking Reception (see page 9)
• Programme Search (see page 12)
Searching for your favorite
FM RDS programme
You can tune in to a station broadcasting your
favorite programme by searching for a PTY code.
•
To store your favorite programme types, see
page 8.
~ The last selected PTY
code appears.
Ÿ Select one of your favorite
programme types.
or
Select one of the PTY codes (see
page 15).
To be continued...
EN06-11_KD-G162_1[EX_EU]f.indd 7EN06-11_KD-G162_1[EX_EU]f.indd 7 10/18/05 4:45:23 PM10/18/05 4:45:23 PM

8
ENGLISH
Using the standby receptions
TA Standby Reception
TA Standby Reception allows the unit to switch
temporarily to Traffic Announcement (TA)
from any source other than AM.
The volume changes to the preset TA volume
level if the current level is lower than the preset
level (see page 12).
To activate TA Standby Reception
The TP (Traffic Programme)
indicator either lights up or
flashes.
• If the TP indicator lights up, TA Standby
Reception is activated.
• If the TP indicator flashes, TA Standby
Reception is not yet activated. (This occurs
when you are listening to an FM station
without the RDS signals required for TA
Standby Reception.)
To activate TA Standby Reception, tune in to
another station providing these signals. The
TP indicator will stop flashing and remain lit.
To deactivate the TA Standby Reception
The TP indicator goes off.
PTY Standby Reception
PTY Standby Reception allows the unit to
switch temporarily to your favorite PTY
programme from any source other than AM.
To activate and select your favorite PTY code
for PTY Standby Reception, see page 12.
The PTY indicator either lights up or flashes.
• If the PTY indicator lights up, PTY Standby
Reception is activated.
• If the PTY indicator flashes, PTY Standby
Reception is not yet activated.
To activate PTY Standby Reception, tune in
to another station providing these signals. The
PTY indicator will stop flashing and remain lit.
To deactivate the PTY Standby Reception,
select “OFF” for the PTY code (see page 12).
The PTY indicator goes off.
! Start searching for your favorite
programme.
If there is a station
broadcasting a programme
of the same PTY code as you
have selected, that station is
tuned in.
Storing your favorite programme
types
You can store si favorite programme types.
Preset programme types in the number buttons
(1 to 6):
1 Select a PTY code (see page 7).
2 Select the preset number (1 – 6) you
want to store into.
Ex.: When ROCK M” is selected
3 Repeat steps 1 and 2 to store other
PTY codes into other preset numbers.
4 Finish the procedure.
EN06-11_KD-G162_1[EX_EU]f.indd 8EN06-11_KD-G162_1[EX_EU]f.indd 8 10/18/05 4:45:24 PM10/18/05 4:45:24 PM

9
ENGLISH
To locate a particular track
To select a number from 01 – 06:
To select a number from 07 – 12:
Prohibiting disc ejection
You can lock a disc in the loading slot.
To cancel the prohibition, repeat the same
procedure.
Selecting the playback modes
You can use only one of the following playback
modes at a time.
1
2 Select your desired playback mode.
7 Repeat play
Mode Plays repeatedly
TRK RPT : The current track.
RPT OFF : Cancels.
7 Random play
Mode Plays at random
DISC RND : All tracks of the current disc.
RND OFF : Cancels.
Tracing the same programme—
Net ork-Tracking Reception
When driving in an area where FM reception
is not sufficient enough, this unit automatically
tunes in to another FM RDS station of the
same network, possibly broadcasting the same
programme with stronger signals (see the
illustration on page 15).
When shipped from the factory, Network-
Tracking Reception is activated.
To change the Network-Tracking Reception
setting, see “AF-REG” on page 11.
Disc operations
Playing a disc in the unit
All tracks will be played repeatedly until you
change the source or eject the disc.
To stop play and eject the
disc
To fast-for ard or reverse
the track
To go to the next or
previous tracks
EN06-11_KD-G162_1[EX_EU]f.indd 9EN06-11_KD-G162_1[EX_EU]f.indd 9 10/18/05 4:45:25 PM10/18/05 4:45:25 PM

10
ENGLISH
Sound adjustments
You can select a preset sound mode suitable to
the music genre (C-EQ: custom equalizer).
1
2
Indication (For)
BAS TRE LOUD
(bass) (treble) (loudness)
USER (Flat sound) 00 00 OFF
ROCK
(Rock or disco music) +03 +01 ON
CLASSIC
(Classical music) +01 –02 OFF
POPS (Light music) +04 +01 OFF
HIP HOP
(Funk or rap music) +02 00 ON
JAZZ (Jazz music) +02 +03 OFF
Adjusting the sound
You can adjust the sound characteristics to your
preference.
1
2
Indication, [Range]
BAS*1 (bass), [–06 to +06]
Adjust the bass.
TRE*1 (treble), [–06 to +06]
Adjust the treble.
FAD*2 (fader), [R06 to F06]
Adjust the front and rear speaker balance.
BAL (balance), [L06 to R06]
Adjust the left and right speaker balance.
LOUD*1 (loudness), [LOUD ON or LOUD OFF]
Boost low and high frequencies to produce a
well-balanced sound at low volume level.
VOL (volume), [00 to 30 or 50*3]
Adjust the volume.
*1 When you adjust the bass, treble, or loudness,
the adjustment you have made is stored for
the currently selected sound mode (C-EQ)
including USER.”
*2 If you are using a two-speaker system, set the
fader level to 00.”
*3 Depending on the amplifier gain control
setting. (See page 12 for details.)
Preset values
Ex.: When ROCK” is selected
EN06-11_KD-G162_1[EX_EU]f.indd 10EN06-11_KD-G162_1[EX_EU]f.indd 10 10/18/05 4:45:26 PM10/18/05 4:45:26 PM

11
ENGLISH
Indications Selectable settings, [reference page]
DEMO
Display demonstration
DEMO ON : [Initial]; Display demonstration will be activated
automatically if no operation is done for about
20 seconds, [5].
DEMO OFF : Cancels.
CLOCK H
Hour adjustment
0 – 23 (1 – 12), [5]
[Initial: 0 (0:00)]
CLOCK M
Minute adjustment
00 – 59, [5]
[Initial: 00 (0:00)]
24H/12H
Time display mode
12H O 24H, [5]
[Initial: 24H]
CLK ADJ
Clock adjustment
AUTO : [Initial]; The built-in clock is automatically adjusted
using the CT (clock time) data in the RDS signal.
OFF : Cancels.
AF-REG
Alternative frequency/
regionalization reception
When the received signals from the current FM RDS station become
weak...
AF : [Initial]; Switches to another station (the programme
may differ from the one currently received), [9].
• The AF indicator lights up.
AF REG : Switches to another station broadcasting the same
programme.
• The AF and REG indicators light up.
OFF : Cancels.
You can change PSM (Preferred Setting Mode)
items listed in the table below.
1
2 Select a PSM item.
General settings — PSM
3 Adjust the PSM item selected.
4 Repeat steps 2 and 3 to adjust other
PSM items if necessary.
5 Finish the procedure.
To be continued...
EN06-11_KD-G162_1[EX_EU]f.indd 11EN06-11_KD-G162_1[EX_EU]f.indd 11 10/18/05 4:45:27 PM10/18/05 4:45:27 PM

12
ENGLISH
Indications Selectable settings, [reference page]
PTY-STBY
PTY standby
Activates PTY Standby Reception with one of the PTY codes, [8].
OFF [Initial]
= PTY codes, [15] = (bac to the beginning)
TA VOL
Traffic announcement
volume
[Initial: VOL 15]; VOL 00 — VOL 30 or 50*, [8]
P-SEARCH
Programme search
ON : Using the AF data, the unit tunes in to another
frequency broadcasting the same programme as the
original preset RDS station is if the preset station
signals are not sufficient.
OFF : [Initial]; Cancels.
TEL
Telephone muting
MUTING 1/MUTING 2 : Select either one which mutes the sounds
while using a cellular phone.
OFF : [Initial]; Cancels.
AMP GAIN
Amplifier gain control
You can change the maximum volume level of this unit.
LOW PWR : VOL 00 – VOL 30 (Select this if the maximum power
of the spea er is less than 45 W to prevent them from
damaging the spea er.)
HIGH PWR : [Initial]; VOL 00 – VOL 50
IF BAND
Intermediate frequency
band
AUTO : [Initial]; Increase the tuner selectivity to reduce
interference noises between close stations. (Stereo
effect may be lost.)
WIDE : Subject to the interference noises from adjacent
stations, but sound quality will not be degraded and
maintains the stereo effect.
* Depends on the amplifier gain control.
EN12-17_KD-G162_1[EX_EU]f.indd 12EN12-17_KD-G162_1[EX_EU]f.indd 12 10/18/05 4:44:41 PM10/18/05 4:44:41 PM

ENGLISH
13
Maintenance
How to clean the connectors
Frequent detachment will deteriorate the
connectors.
To minimize this possibility, periodically wipe
the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.
Connector
Moisture condensation
Moisture may condense on the lens inside the
CD player in the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the disc and
leave the unit turned on for a few hours until
the moisture evaporates.
How to handle discs
When removing a disc from
its case, press down the center
holder of the case and lift the
disc out, holding it by the edges.
• Always hold the disc by the
edges. Do not touch its recording surface.
When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).
• Ma e sure to store discs into the cases after
use.
Center holder
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe it
with a soft cloth in a straight line
from center to edge.
• Do not use any solvent (for example,
conventional record cleaner, spray, thinner,
benzine, etc.) to clean discs.
To play new discs
New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
unit may reject the disc.
To remove these rough spots, rub the edges
with a pencil or ball-point pen, etc.
Warped disc
Sticker Sticker residue
Disc Stick-on label
Do not use the following discs:
EN12-17_KD-G162_1[EX_EU]f.indd 13EN12-17_KD-G162_1[EX_EU]f.indd 13 10/18/05 4:44:44 PM10/18/05 4:44:44 PM

14
ENGLISH
• When Alternative Frequency Reception
is activated (with AF selected), Networ -
Trac ing Reception is also activated
automatically. On the other hand, Networ -
Trac ing Reception cannot be deactivated
without deactivating Alternative Frequency
Reception. (See page 11.)
• If you want to now more about RDS, visit
«http://www.rds.org.u ».
Disc operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does
not comply with the “Compact Disc Digital
Audio” standard. Therefore, the use of Non-
DVD side of a DualDisc on this product may
not be recommended.
eneral
• This unit has been designed to reproduce
CDs, and CD-Rs (Recordable)/CD-RWs
(Rewritable) in audio CD (CD-DA format).
• When a disc has been loaded, selecting
“DISC” for the playbac source starts disc
play.
Inserting a disc
• When a disc is inserted upside down, the disc
automatically ejects.
• Do not insert 8 cm discs (single CD) and
unusual shape discs (heart, flower, etc.) into
the loading slot.
More about this unit
Basic operations
Turning on the power
• By pressing SOURCE on the unit, you can
also turn on the power. If the source is ready,
playbac also starts.
Turning off the power
• If you turn off the power while listening to a
disc, disc play will start from where playbac
has been stopped previously, next time you
turn on the power.
Selecting the sources
• When no disc is loaded in the unit, “DISC”
cannot be selected.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and
stations are stored newly.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in
No. 1 will be automatically tuned in.
• When storing a station manually, the
previously preset station is erased when a new
station is stored in the same preset number.
FM RDS operations
• Networ -Trac ing Reception requires
two types of RDS signals—PI (Programme
Identification) and AF (Alternative
Frequency) to wor correctly. Without
receiving these data correctly, Networ -
Trac ing Reception will not operate correctly.
• If a Traffic Announcement is received, the
volume level automatically changes to the
preset level (TA VOL) if the current level is
lower than the preset level.
EN12-17_KD-G162_1[EX_EU]f.indd 14EN12-17_KD-G162_1[EX_EU]f.indd 14 10/18/05 4:44:44 PM10/18/05 4:44:44 PM

ENGLISH
15
eneral settings—PSM
• If you change the “AMP GAIN” setting from
“HIGH PWR” to “LOW PWR” while the
volume level is set higher than “VOL 30,” the
unit automatically changes the volume level to
“VOL 30.”
PTY codes
NEWS, AFFAIRS, INFO, SPOR , EDUCA E, DRAMA, CUL URE,
SCIENCE, VARIED, POP M (music), ROCK M (music), EASY
M (music), LIGH M (music), CLASSICS, O HER M (music),
WEA HER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE
IN, RAVEL, LEISURE, JAZZ, COUN RY, NA ION M (music),
OLDIES, FOLK M (music), DOCUMEN
Network-Tracking Reception
Programme A broadcasting on different frequency areas
(01 – 05)
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can play bac multi-session discs;
however, unclosed sessions will be s ipped
while playing.
• Some CD-Rs or CD-RWs may not play
bac on this unit because of their disc
characteristics, or for the following causes:
– Discs are dirty or scratched.
– Moisture condensation occurs on the lens
inside the unit.
– The pic up lens inside the unit is dirty.
– CD-R/CD-RW on which the files are
written with “Pac et Write” method.
– There are improper recording conditions
(missing data, etc.) or media conditions
(stained, scratched, warped, etc.).
• CD-RWs may require a longer readout time
since the reflectance of CD-RWs is lower than
that of regular CDs.
• Do not use the following CD-Rs or CD-RWs:
– Discs with stic ers, labels, or protective seal
stuc to the surface.
– Discs on which labels can be directly
printed by an in jet printer.
Using these discs under high temperatures or
high humidities may cause malfunctions or
damage to the unit.
Changing the source
• If you change the source, playbac also stops
(without ejecting the disc).
Next time you select “DISC” for the playbac
source, disc play starts from where it has been
stopped previously.
Ejecting a disc
• If the ejected disc is not removed within
15 seconds, the disc is automatically inserted
again into the loading slot to protect it from
dust. (Disc will not play this time.)
EN12-17_KD-G162_1[EX_EU]f.indd 15EN12-17_KD-G162_1[EX_EU]f.indd 15 10/18/05 4:44:46 PM10/18/05 4:44:46 PM

16
ENGLISH
Symptoms Remedies/Causes
eneral
• Sound cannot be heard from the
spea ers.
• Adjust the volume to the optimum level.
• Chec the cords and connections.
• The unit does not wor at all. Reset the unit (see page 2).
FM/AM
• SSM automatic presetting does not
wor .
Store stations manually.
• Static noise while listening to the radio. Connect the aerial firmly.
Disc playback
• Disc cannot be played bac . Insert the disc correctly.
• CD-R/CD-RW cannot be played bac .
• Trac s on the CD-R/CD-RW cannot be
s ipped.
• Insert a finalized CD-R/CD-RW.
•
Finalize the CD-R/CD-RW with the component
which you used for recording.
• Disc can be neither played bac nor
ejected.
• Unloc the disc (see page 9).
• Eject the disc forcibly (see page 2).
• Disc sound is sometimes interrupted. • Stop playbac while driving on rough roads.
• Change the disc.
• Chec the cords and connections.
• “NO DISC” appears on the display. Insert a playable disc into the loading slot.
Troubleshooting
What appears to be trouble is not always serious. Chec the following points before calling a service
center.
EN12-17_KD-G162_1[EX_EU]f.indd 16EN12-17_KD-G162_1[EX_EU]f.indd 16 10/18/05 4:44:47 PM10/18/05 4:44:47 PM

ENGLISH
17
Specifications
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front: 45 W per channel
Rear: 45 W per channel
Continuous Power Output (RMS):
Front: 1 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than 0.8%
total harmonic distortion.
Rear: 1 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than 0.8%
total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass: ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 0 dB
Line-Out Level/Impedance:
2.0 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
TUNER SECTION
Frequency Range:
FM: 8 .5 MHz to 108.0 MHz
AM: (MW) 522 kHz to 1 620 kHz
(LW) 144 kHz to 2 9 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 μV/ 5 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 μV/ 5 Ω)
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 30 dB
Capture Ratio: 1.5 dB
[MW Tuner]
Sensitivity: 20 μV
Selectivity: 35 dB
[LW Tuner]
Sensitivity: 50 μV
CD PLAYER SECTION
Type: Compact disc player
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Number of Channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
GENERAL
Power Requirement:
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:
0°C to +40°C
Dimensions (W × H × D):
Installation Size (approx.):
182 mm × 52 mm × 150 mm
Panel Size (approx.):
188 mm × 58 mm × 11 mm
Mass (approx.):
1.2 kg (excluding accessories)
Design and specifications are subject to change
without notice.
EN12-17_KD-G162_1[EX_EU]f.indd 17EN12-17_KD-G162_1[EX_EU]f.indd 17 10/21/05 3:11:48 PM10/21/05 3:11:48 PM

2
FRANÇAIS
Comment détacher/attacher le
panneau de commande
Détachement...
Attachement...
Remarque: Uniquement pour les utilisateurs du
modèle [EX] au Royaume Uni et dans les pays
européens.
Pour des raisons de sécurité, une carte
d’identification numérotée est fournie a ec cet
appareil, et le même numéro d’identification est
imprimé sur le châssis de l’appareil. Conser er
cette carte dans un endroit sûr, elle pourra aider
les autorités pour identifier otre appareil en cas
de ol.
Avertissement:
Si ous souhaitez opérer l’appareil pendant
que ous conduisez, assurez- ous de bien
regarder de ant ous afin de ne pas causer
un accident de la circulation.
Comment réinitialiser votre appareil
• Vos ajustements préréglés sont aussi effacés.
Comment forcer l’éjection d’un
disque
• Si cela ne fonctionne pas, essayez de
réinitialiser l’autoradio.
• Faites attention de ne pas faire tomber le
disque quand il est éjecté.
Merci pour a oir acheté un produit JVC.
Veuillez lire attenti ement toutes les instructions a ant d’utiliser l’appareil afin de bien comprendre
son fonctionnement et d’obtenir les meilleures performances possibles.
IMPOR AN POUR PRODUI S LASER
1. PRODUIT LASER CLASSE 1
2. AT TE NTI O N : N’ou rez pas le cou ercle supérieur. Il n’y a aucune pièce réparable par
l’utilisateur à l’intérieur de l’appareil; confiez toute réparation à un personnel qualifié.
3. ATTENTION: Risque de radiations laser isible et in isible quand l’appareil est ou ert et que
le système de errouillage ne fonctionne pas ou a été mis hors ser ice. É itez toute exposition
directe au rayon.
4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À
L’EXTÉRIEUR DE L’APPAREIL.
FR02-05_KD-G162_1[EX_EU]f.indd 2FR02-05_KD-G162_1[EX_EU]f.indd 2 10/13/05 4:24:36 PM10/13/05 4:24:36 PM

FRANÇAIS
3
Comment lire ce manuel
• L’utilisation des touches est principalement
expliquée a ec des illustrations dans le tableau
ci-dessous.
• est utilisé pour indiquer un indicateur
affiché pour l’opération correspondante.
• Certains conseils et remarques sont donnés
dans la section “Pour en sa oir plus à propos
de cet autoradio” ( oir les pages 14 et 15).
Appuyez briè ement.
Appuyez répétiti ement.
Maintenez pressée jusqu’à
ce que ous obteniez la
réponse souhaitée.
Maintenez pressées les
deux touches en même
temps.
Comment utiliser la touche M MODE
Si ous appuyez sur M MODE, l’appareil entre
en mode de fonction, et les touches numériques
fonctionnent comme touches de fonction
différentes.
Ex. : Quand la touche numérique 2
fonctionne comme touche MO
(monophonique).
Pour utiliser à nouveau ces touches pour leurs
fonctions originales après avoir appuyé sur M
MODE, attendez 5 secondes sans appuyer sur
aucune de ces touches jusqu’à ce que le mode de
fonction soit annulé ou appuyez de nou eau sur
M MODE.
TABLE DES MATIERES
Panneau de commande
—
KD-G162 et KD-G161 ............................ 4
Pour commencer ............................... 5
Opérations de base ................................................ 5
Fonctionnement de la radio .............. 6
Utilisation du système FM RDS ........... 7
Recherche de votre programme FM RDS préféré ... 7
Opérations des disques ..................... 9
Lecture d’un dis ue dans l’autoradio ................... 9
Ajustements sonores ......................... 10
Réglages généraux — PSM ............... 11
Entretien ......................................... 13
Pour en savoir plus à propos de cet
autoradio ...................................... 14
Guide de dépannage ......................... 16
Spécifications ................................... 17
Précautions sur le réglage du volume:
Les disques produisent très peut de bruit
par rapport aux autres sources. Réduisez le
olume a ant de reproduire un disque afin
d’é iter d’endommager les enceintes par la
soudaine augmentation du ni eau de sortie.
Pour sécurité...
• N’augmentez pas trop le olume car cela
bloquerait les sons de l’extérieur rendant la
conduite dangereuse.
• Arrêtez la oiture a ant de réaliser toute
opération compliquée.
empérature à l’intérieur de la voiture...
Si otre oiture est restée garée pendant
longtemps dans un climat chaud ou froid,
attendez que la température à l’intérieur de la
oiture rede ienne normale a ant d’utiliser
l’appareil.
Indicateur de compte à rebours
Appuyez sur une
de ces touches.
FR02-05_KD-G162_1[EX_EU]f.indd 3FR02-05_KD-G162_1[EX_EU]f.indd 3 10/13/05 4:24:42 PM10/13/05 4:24:42 PM

4
FRANÇAIS
Panneau de commande — KD-G612/KD-G611/KD-G511
i Touche M MODE
o Touche (libération du panneau de
commande)
Fenêtre d’affichage
; Indicateur DISC
a Indicateur RND (lecture aléatoire de
disque)
s Indicateur R T (répétition)
d Indicateur LOUD (loudness)
f Indicateur EQ (égaliseur)
g Indicateurs de mode sonore (C-EQ:
égaliseur personnalisé)—JAZZ, CLASSIC,
HI HO , O S, ROCK, USER
h Indicateur d’affichage de la source / niveau
de volume / Indicateur de compte à rebours
j Affichage principal
k Indicateurs RDS—T , TY, AF, REG
l Indicateurs de réception du tuner—
ST (stéréo), MO (monophonique)
Identification des parties
Fenêtre d’affichage
Panneau de commande — KD-G162 et KD-G161
1 Touche (attente/sous tension/
atténuation)
2 Touche SOURCE
3 Touche BAND
4 Fente d’insertion
5 Fenêtre d’affichage
6 Touche 0 (éjection)
7 Touche T / TY (programme
d’informations routières/type de
programme)
8 Touches ¢/4
9 Molette de commande
p Touche SEL (sélection)
q Touche DIS (affichage)
w Touche EQ (égaliseur)
e Touche MO (monophonique)
r Touche SSM (Mémorisation automatique
séquentielle des stations puissantes)
t Touches numériques
y Touche R T (répétition)
u Touche RND (aléatoire)
FR02-05_KD-G162_1[EX_EU]f.indd 4FR02-05_KD-G162_1[EX_EU]f.indd 4 10/24/05 11:11:45 AM10/24/05 11:11:45 AM