JVC LoLux TK-T8101WPRU User manual




IR BULLET CAMERA TK-T8101WPRU
IR BULLET CAMERA TK-T8101WPRE
INSTRUCTIONS



Important Safety Information

Before attempting to connect or operate this product, please read these instructions
carefully and save this manual for future use.
1

Important Safety Information

Warning and Operating Notes
Installation and serving the camera should be performed only by qualified and experienced technicians to
conform to all local codes and to maintain your warranty.
WARNING! The use of CSA certified/UL Listed Class 2 power adapters are required to ensure
compliance.
Note:
This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked
"Class 2" or Listed Adapter marked "L.P.S." (or "Limited Power Source") and rated
output DC 12V, 0.58A minimum or AC 24V, 60Hz, 0.58A minimum. (for USA)
WARNING! To reduce the risk of fire or electric shock, do not expose the product to rain or
moisture.
Caution
Connect only one camera to the power line,
AC24V/DC12V.Do not share the power line with other
equipment. The power cable between power source and
the camera must be under 3 m.
Operating Notes
Power Supply: This bullet camera can operate on AC 24V or DC 12V.
Note
Connectors and field wiring terminals for external Class 2
circuits provided with marking indicating minimum Class of
wiring to be used. Class 2 shall be marked adjacent to the
field wiring terminals.
Operating Conditions
yAvoid viewing very bright objects (example, light fixtures) for extended periods.
yAvoid operating or storing the unit in the following locations:
-Extremely humid, dusty, hot, cold environments (where the operating temperature is outside the
recommended range of 14°F to 122°F [-10°C to +50°C].)
-Close to sources of powerful radio or TV transmitters
-Close to fluorescent lamps or objects reflecting light
-Under unstable light sources (may cause flickering)
2

CONTENTS
1 Instructions ........................................................................................................................................... 4
1.1 Before You Begin .......................................................................................................................... 4
1.2 Dimensions ................................................................................................................................... 4
1.3 Names of Camera Parts................................................................................................................ 5
1.4 Routine Maintenance .................................................................................................................... 6
2 Installation ............................................................................................................................................... 7
2.1 Mounting the Camera.................................................................................................................... 7
3. OSD Settings.........................................................................................................................................10
3.1
Lens ....................................................................................................................... .....................10
3.2 SHUTTE
R/AGC ................................................................................................................
.......... 10
3.3 WHITE BAL................................................................................................................................. 11
3.4 BACKLIGHT................................................................................................................................ 11
3.5 PICTURE
ADJUST ............................................................................................................. ........12
3.6 ATR ........................................................................................................................ .....................12
3.7 MOTION
DET................................................................................................................. .............12
3.8 PRI
VACY .................................................................................................................... ................12
3.9 DAY/NIGHT.................................................................................................................................. 13
3.10 NR............................................................................................................................................. 13
3.11 CAMERA ID .............................................................................................................................. 13
3.12 LANGUAGE .............................................................................................................................. 13
3.13 CAMERA RESET...................................................................................................................... 13
3.14 SAVE ALL ................................................................................................................................. 13
4. Specification ......................................................................................................................................... 14
3

Introductions


1．Instructions
The IR Bullet camera is ideal for indoor installation in commercial and residential environment.
1.1 Before You Begin
Please read this guide carefully before you install the bullet camera. Keep this guide for future reference.
1.2 Dimensions
4



Part Names and Locations
1.3 Names of Camera Parts
Figure 2-1
1. Camera main body
2. Sun shield:Minimize the effects of rain
and sunlight on image quality.
3. Externally adjustable focal length &
focus
4. OSD menu joystick:
To use the OSD joystick control:
•Press the OSD joystick control straight
down to enter the Main menu or a
selected item.
•Move the OSD joystick control UP,
DOWN, LEFT and RIGHT to navigate
through menus and options.
5. Mount bracket:Connects to the Mount.
6. BNC connector: Connects to the VIDEO
IN connector of the Monitor Video Connector
7. Power connector: Connects to the
external power source.
DC12V/AC24V (Please refer to camera label)
5



Part Names and Locations
1.4 Routine Maintenance
yUse a soft, dry cloth to remove any fingerprints or dust.
yClean the camera housing with a soft, dry cloth. For more stubborn stains, use a cloth dampened
with a small quantity of neutral detergent, then wipe dry.
Caution: Do not use volatile solvents such as alcohol, benzene or thinners to avoid damaging the
surface finish.
6



Installation
2 Installation
2.1 Mounting the Camera
Step 1: Drill mounting holes and insert anchors.
In desired location, use the supplied Guide Pattern to drill three 5mm mounting holes. Then insert the
supplied anchors into the holes.
To prevent the camera from falling off, ensures it is connected to a firm place (ceiling slab or channel)
using a Safety Wire (fall prevention wire is not supplied).
Safety Wire (fall prevention wire is not
supplied).
Please tighten a safety wire on a firm place
as photo.
7



Installation
Step 2: Pass all the signal cables through the hole for the cables.
Optionally connect a video monitor to the BNC connector if you want to perform focus/zoom adjustments
during the installation.

Step 3: For static electricity protection, ensure that the rubber pad is placed inside
the mounting bracket base.
Step 4: Modify the position of camera
Loosen the two screws (left and right) first (just rotate slightly one circle or the screws will fall down),
second, rotate the Retaining ring then you will be able to hold the camera and adjust its angle. Fasten
the screws and retaining ring to ensure the desired angle.
8



Installation
Step 5: Adjustment
It can be adjusted once the screw is fully loosened. After adjustment, be sure to lock it tightly for
waterproof.
Notice: Please be careful when adjusting Tele/Wide and Near/Far so as to avoid damage to the lens
Step 6: Place the three provided insulation caps onto the three tapping screws.
Insert the screws to the screw holes on the camera bracket, and then tighten the screws to the anchors
to attach the camera..



Tele &WideControl
Near&FarControl
OSDjoystick
9