(D MODE/SCAN switch
This switch is used to select both FM STEREO/MONO
mode and AUTO/MANUAL scanning mode. These func-
tions are related to each other. When stereo reception is
possible, set this switch to AUTo/sTEREo (r) for auto
tuning. When signals are too weak to be received, set to
MANU/MONO (^) for manual tuning; in this mode the
left and right channel FM signals are mixed and heard
from both speakers.
(E rurutruc buttohs
Auto tuning
Up-scanning button ( > ): When this button is pressed,
beeps will be heard and the tuned-in frequency changes in
the direction of increasing frequencies. Use this button to
search the upper frequency broadcast. Scanning (Auto
Tuning) stops automatically when the next FM (or AM)
station is pulled in. This tuned:in frequency is displayed
digitally by the f requency indicator.
When you continue to press this button, scanning does
not stop even if broadcasts which could be tuned in are
detected. Press the Up-scanning button and then press the
Down-scanning button to select stations by down-scan-
ning.
Down-scanning button ( 1 ): Press to tune in the direc-
tion of decreasing frequencies. Use this button to search
the lower f requency station. Functions are identical with
those of the Up-scanning button.
Note: Scanning starts when the < or > button is press-
ed and is stopped by pressing th'e MODE/SCAN
switch.
Manual tuning
Manual tuning is possible by pressing the MODE/SCAN
switch @ . Pressing the Up-Down-scanning buttons, thti
tuned-in frequency changes in 100kHz steps for FM
reception (50 kHz steps for Europe, U.K., and Australia)
or 10 kHz steps for AM (MW) (9 kHz steps for Europe,
U.K. and Australia), or 1 kHz steps for LW. Tapping this
button changes the tuner step by step, continuous press-
ing (more than 0.5 sec.) changes tuning in a high speed
scanning sequence which stop when released.
lf one of these buttons is pressed immediately after the
AM or FM source select button, the tone of the beep will
be different.
(D MEMORY switch
Press this switch and the memory indicator will light to
show that this unit is ready to receive a memory setting.
(This switch is a non-lock type.) Pressing the station select
button while the MEMORY indicator is lit (for about 10
sec.) makes it possible to memorize the station being
received. When the MEMORY indicator is not lit, the
memory function does not operate.
(D MEMORY indicator
When the MEMORY switch is pressed, this MEMORY
indicator lights to show that the unit is ready to register
the preset station to memory. This indicator will go out
automatically in about 10 sec. or by pressing the station
select button.
@ Station select buttons/Station indicators
These buttons are used to select one of the preset stations
or to memorize the station for an individual channel.
When one of these buttons is pressed, beeps will be heard
and the LED indicator on the corresponding button lights
to indicate which channel is in operation.
lf one of these buttons is pressed when the MEMORY
switch (D is pressed in, the station which is being
received will be "Memorized". One of the station select
buttons can be used in common for one FM station and
one AM station (one MW or LW station for R-X40L).
lf you change the mode from radio reception to any
other mode including power-off and back to radio recep-
tion, the station previously selected with the station
select buttons remains tuned in.
lf one of these buttons is pressed immediately after the
AM or FM source select button, the tone of the beepwill
be different.
O FM STEREo indicator
This indicator lights when an FM stereo broadcast is tuned
in.
@ Frequency indicator
The tuned-in frequency is displayed digitally. Four digits
(kHz) are displayed for AM reception and five digits
(MHz) (for Europe, U.K., Australia and other countries)
or four digits (MHz) (for U.S.A., and Canada) are display-
ed for FM reception.
@ stcrual STRENGTH indicator
This is used in tuning to both FM and AM (MW/LW)
broadcasts. The greater the number of LEDs that light,
the stronger the signal being received.
@ ourpur LEVEL indicator
These LEDs indicate the output level.
(D TAPE MONITOR indicator
This indicator lights when the TAPE MONITOR switch is
pressed for monitoring or listening to the tape recordings.
\z
v
R-X4O / R-X4OL
No.2603 -3-
v
