K-TOR POWER BOX User manual

®
Pedal Power requires physical exercise; ensure you are healthy
enough to operate. Consult a physician if you are unsure. Connect
only compatible devices. Do not stand on generator. Do not overload.
INSTRUCTIONAL VIDEO & MORE INFO ONLINE: WWW.K-TOR.COM
PARTS
Left Pedal*
Right Pedal*
Main Body
Feet (2)
*RAND LLABELS
IDENTIFY PEDALS
COMPATIBILITY
The K-TOR Power Box pedal power generator provides DC power and has been designed to be used with devices that
accept DC current. Modern consumer electronic devices such as cell phones, tablets, digital cameras, etc., fall into this
category. Appliances like a TV, Microwave and Refrigerator require AC power and are not directly compatible with K-TOR
generators. To run devices that use AC power or more than 20 Watts of DC power, refer to the advanced charging guide on
k-tor.com.
WARRANTY
K-TOR provides a one year warranty on all generators starting from the date of purchase. The one year warranty covers
defects in material and workmanship only. If a unit is found to be defective, K-TOR will repair, replace or refund the unit. To
request a warranty claim, contact K-TOR by emailing [e-mail]. Once a return has been authorized, the unit must be
returned to the factory postage prepaid. Do not modify or overload K-TOR generators as this can damage the unit and will
void the warranty.
DISCLAIMER
K-TOR accepts no liability from loss of use, injury or direct or consequential damages as a result of the use or inability to use
or failure of K-TOR products.

CONVERTING FROM STORAGE MODE TO GENERATOR MODE
UNCLIP PEDALS
1
Detach both pedals by removing them from the plastic clips
attached to the feet.
2
REMOVE FEET
Remove the feet from the generator by pulling out the four
feet pins and removing the generator.
OPEN BASE
3
Unclip and remove the leg pin. Rotate the leg all the way
around and re-insert the pin (stiff when new). Lock in place.
4
ATTACH FEET
Align the holes in the generator legs with the holes in the
feet. Insert the feet pins to lock in place.
ALIGN
HOLES
5
ATTACH PEDAL
The right pedal is marked ‘R’ on the inside of the crank arm.
Lift the locking clip and slide the locking disc to the unlocked
position. Once unlocked, slide pedal onto crank shaft.
UNLOCKED
LOCKING
CLIP - LIFT
GENTLY AND
SLIDE DISK TO
UNLOCKED
POSITION
ATTACH
RIGHT
PEDAL
TO RIGHT
CRANK
NOTE: There is a right and left pedal. It is important they go
on the correct side or the pedals will loosen and may become
damaged.
6
LOCK PEDAL
Make sure the pedal is fully seated on the crank shaft. With
the pedal securely attached to the crank shaft, lock the pedal
in place by sliding the locking disc into the locked position.
FULLY SEAT PEDAL ON CRANK
SHAFT
NOTE: If the pedals are not in the unlocked position when
placed onto the crank shaft, they will not fully seat or prop-
erly lock into place.
Repeat steps 5 and 6 to attach the left pedal. The power box is now in generator mode. To return to storage mode, follow the
same steps in reverse.
WWW.K-TOR.COM

OPERATING IN GENERATOR MODE
1
SETUP
The generator can be operated with two hands or two feet
and should be spun in a forward bicycle motion.
Mounting holes in the generator feet can be used to screw
down or stake down the unit for a more stable base. This is
highly recommended.
MOUNTING HOLE MOUNTING HOLE
2
PLUG-IN
Connect a compatible device and its charger directly to the
outlet in the K-TOR Power Box pedal power generator.
OPTION: You may also use an extension cord to connect the
unit to your charger. You may charge more tha one device at
a time as long as the total power does not exceed the 20 Watt
maximum rating of the pedal generator.
3
READY
Position yourself, so that your hands or feet are directly over
the generator. Apply downward pressure with feet (or hands)
to help hold the generator in place.
OUTLET FACING
AWAY FROM USER
DO NOT STAND ON THE GENERATOR OR PEDALS
4
SPIN
Crank in a forward bicycle motion, accelerating quickly to 90
RPM (1.5 rotations per second) for full power and efficient
operation.
ACCELERATE QUICKLY TO FULL SPEED 90 RPM
OPERATING SUMMARY
- Make sure the pedals are on the correct crank shaft in the locked position
- Pull on the cranks to ensure they are locked on the shaft and will not come off
- Failure to lock the pedals correctly will damage the unit
- Ensure that the feet pins and base pin are fully inserted
- Make sure the unit is on a flat stable surface, preferably screwed down
- Verify that you have enough space to operate the generator
- Check the cord to make sure it will not get caught while operating
- Apply downward pressure to the pedals to hold generator in place
- Accelerate quickly to full speed 90 RPM (1.5 revolutions per second)
WWW.K-TOR.COM