K-TOR POWER BOX User manual

®
PARTS LIST
COMPATIBILITY
K-TOR provides a one year warranty on all generators sold starting from the date of purchase. The one year warranty covers
defects in material and workmanship only. If a unit is found to be defective, K-TOR will repair, replace or refund the unit. To
request a warranty claim, contact K-TOR by emailing [e-mail]. Once a return has been authorized, the unit must be
returned to the factory postage prepaid. Do not modify or overload K-TOR generators as this can damage the unit and will
void the warranty.
K-TOR accepts no liability from loss of use, injury or direct or consequential damages as a result of the use or inability to use
or failure of K-TOR products.
The K-TOR Power Box pedal power generator provides DC power and has been designed to be used with devices that
accept DC current. Modern consumer electronic devices such as cell phones, tablets, digital cameras, etc., fall into this
category. Appliances like a TV, Microwave and Refrigerator require AC power and are not directly compatible with K-TOR
generators. To run devices that use AC power or more than 20 Watts of DC power, refer to the advanced charging guide on
k-tor.com.
WARRANTY
DISCLAIMER
PARTS
INSTRUCTIONAL VIDEO & MORE INFO ONLINE: WWW.K-TOR.COM
Left Pedal*
Right Pedal*
Main Body
Feet (2)
Pedal Power requires physical exercise; ensure you are healthy
enough to operate. Consult a physician if you are unsure. Connect
only compatible devices. Do not stand on generator. Do not overload.
*RAND LLABELS
IDENTIFY PEDALS

STEP TWO
6
LOCK PEDAL
5
ATTACH PEDAL
4
ATTACH FEET
3
OPEN BASE
2
REMOVE FEET
1
UNCLIP PEDALS
Detach both pedals by unclipping them from the plastic clips
attached to the feet.
Remove the feet from the generator by pulling out the four
feet pins and removing the generator.
Seat the holes in the generator legs with the holes in the
feet. Insert the feet pins to lock in place.
The right pedal is marked with an ‘R’ on the inside of the
crank arm. Lift the locking clip and slide the locking disc to
the unlocked position. Once unlocked, slide onto crank shaft.
NOTE: There is a right and left pedal. It is important they go
on the correct side or when pedaling the pedals will loosen
and may become damaged.
Unclip and remove the leg pin. Rotate the leg all the way
around and re-insert the pin (stiff when new). Lock in place.
WWW.K-TOR.COM
CONVERTING FROM STORAGE MODE TO GENERATOR MODE
UNLOCKED
LOCKING
CLIP - LIFT
GENTLY AND
SLIDE DISK TO
UNLOCKED
POSITION
ATTACH
RIGHT
PEDAL
TO RIGHT
CRANK
Make sure the pedal is fully seated on the crank shaft. With
the pedal securely attached to the crank shaft, lock the pedal
in place by sliding the locking disc into the locked position.
NOTE: If the pedals are not in the unlocked position when
slid onto the crank shaft, they will not fully seat or properly
lock into place.
Repeat steps 5 and 6 to attach the left pedal. The power box is now in generator mode. To return to storage mode, follow the
same steps in reverse.
FULLY SEAT PEDAL ON CRANK
SHAFT
ALIGN
HOLES

OPERATING IN GENERATOR MODE
Connect a compatible device and its charger directly to the
outlet in the K-TOR Power Box pedal power generator.
OPTION: You may also use an extension cord to connect the
unit to your charger. More than one charger at a time may be
used as long as the total power does not exceed the 20 Watt
maximum rating of the pedal generator.
PLUG-IN
2
PLUG-IN
Position yourself, so that your hands or feet are directly over
the generator. Pressure from feet (or hands) should be made
vertically downward to help hold the generator in places.
Crank in a forward bicycle motion, accelerating quickly to
90rpm (1.5 rotations per second) for full power and efficient
operation.
4
SPIN
3
READY
DO NOT STAND ON THE GENERATOR OR PEDALS
OUTLET FACING
AWAY FROM USER
ACCELERATE QUICKLY TO FULL SPEED 90 RPM
The generator can be operated with two hands or two feet
and should be spun in a forwards bicycle motion.
Mounting holes in the generator feet can be used to screw
down or stake down the unit for a more stable base. This is
highly recommended.
1
SETUP
OPERATING SUMMARY
- Make sure the pedals are on on the correct crank shaft in the locked position
- Pull on the cranks to insure they are locked on the shaft and will not come off
- Failure to lock the pedals on correctly will damage the unit
- Ensure that the feet pins and base pin are fully inserted
- Make sure the unit is on a flat stable surface, preferably screwed down
- Veirfy you have enough space to operate the generator
- Check the cord to make sure it will not get caught while operating
- Place pressure vertically downward on the pedals to hold generator in place
- Accelerate quickly to full speed 90 RPM (1.5 revolutions per second)
WWW.K-TOR.COM
MOUNTING HOLE MOUNTING HOLE