Kaiser SUA-8448KW Datasheet

Model#SUA-8448KW
TABLE HOCKEY

P1 - Main Cabinet
(1 pc)
H1 - 8mm x 130mm Hex Head Bolt
(8 pcs)
H2 - 8mm x 40mm
Hex Head Bolt
(20 pcs)
H3 - M8 Flat Washer
(28 pcs)
H4 - M8 Lock Washer
(28 pcs)
P2 - Leg Baseplate
(2 pcs)
P3 - Middle Leg
(2 pcs)
P4 - Upper Leg
(2 pcs)
P5 - Bottom Leg
(2 pcs)
PARTS IDENTIFIER
(Not to Scale)
HARDWARE IDENTIFIER
(To Scale)
（Not to Scale)
T1 - Socket Head Wrench
(1 pc)
3

ACCESSORIES IDENTIFIER
(Not to Scale)
4
A1 - Striker
(2 pcs)
A2 - Puck
(2 pcs)
A3 - Felt Pad
(2 pcs)
NOTE: A3 Felt Pads may already
be attached to A1 Strikers
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation."
"CAUTION: Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment."

PARTS REQUIRED
12pcs - H2 Hex Head Bolt
12pcs - H4 M8 Lock Washer
12pcs - H3 M8 Flat Washer2pcs - P3 Middle Leg
2pcs - P4 Upper Leg
1pc - P1 Main Cabinet
PARTS REQUIRED
8pcs - H1 Hex Head Bolt 8pcs - H4 M8 Lock Washer
8pcs - H3 M8 Flat Washer
2pcs - P5 Bottom Leg
STEP 1
Attach the P4 Upper Leg, P3 Middle Leg onto the P1 Main Cabinet
using the H2 Hex Head Bolt,H3 M8 Flat Washer and H4 M8 Lock
Washer as shown in FIGURE 1.
Attach the P5 Bottom Leg onto the
P3 Middle Leg using the H1 Hex
Head Bolt,H3 M8 Flat Washer and
H4 M8 Lock Washer as shown in
FIGURE 2.
STEP 2
Screw the P4 Upper Leg with P3 Middle Leg using the H1 Hex
Head Bolt,H3 M8 Flat Washer and H4 M8 Lock Washer as shown
in FIGURE 2.
FIGURE 1
FIGURE 2
5
H2
H4
H3
P3
P4
P3
H2 H3
H3
H4
H2 H3
H4
H2
H4
P1
P4
H1
H4
H3
H3
P5
P3
H1
H4
Tighten H2 bolts using the T1 Socket Head Wrench.
Tighten H1 bolts using the
T1 Socket Head Wrench.

PARTS REQUIRED
8pcs - H2 Hex Head Bolt
8pcs - H4 M8 Lock Washer
8pcs - H3 M8 Flat Washer2pcs - P2 Leg Baseplate
1pc - P1 Main Cabinet
Attach the P2 Leg Baseplate onto the P3 Middle Leg and P5
Bottom Leg using the H2 Hex Head Bolt,H3 M8 Flat Washer and
H4 M8 Lock Washer as shown in FIGURE 3.
FIGURE 3
6
P5
P5
P2
H2
H4
H3
H2
H4
H3
H2
H2
H4
H4
H3
H3
P3
P2
THIS STEP REQUIRES FOUR OR MORE ADULTS.
WHILE FLIPPING THE TABLE OVER, DO NOT ALLOW TABLE
TO REST ON THE SIDE OF LEGS AS THIS COULD DAMAGE THEM.
VERY CAREFULLY TURN THE TABLE OVER AND SET IT ON
ITS LEGS. BE CAREFUL. THE TABLE IS VERY HEAVY.
HOLD TABLE
CABINET DO NOT
HOLD THE
LEGS
DO NOT LEAN THE
TABLE ON ITS LEGS!
STEP 3
Tighten H2 bolts using the T1 Socket
Head Wrench.

7
Customer Service Parts
C3

8
C3
C4
C5
C1
C2
ELECTRONIC CONNECTIONS
C5. Scorer
C6. Blower with A/C Cord
C3. Control Box
C4. Battery Box
C1. Sensor with
Short Wire
C2.Sensor with
Long Wire
NOTE:
ON/OFF switch is attached to the air
fan motor cord. Be sure to always turn
fan motor off when play is completed.
IMPORTANT:
Plug into wall outlet.
Do not allow cord to be a trip hazard.

9
LED SCORING OPERATING