KAM LED BRONCO User manual

Kam LED Bronco
Six lens RGBW gobo lighting effect with DMX
Due to continuous product development, please ensure that you have downloaded
the latest instruction manual for this product from the Kam website at www.kam.co.uk
M A N U A L V E R S I O N 2 .0
1 2 - 0 6 - 13
For the latest instruction manual updates and information on the entire Kam range visit:
www.kam.co.uk
Kam products are manufactured by: Lamba plc, Unit 1, Southfields Road, Dunstable, Bedfordshire, United Kingdom LU6 3EJ
Telephone: (+44) (0)1582 690600 • Fax: (+44) (0)1582 690400 • Email: [email protected] • Web: www.lambaplc.com
Made in China. Due to continuous product development, specifications and appearance are subject to change. © Copyright Lamba plc 2013. E&OE.

Thank you for purchasing this Kam product, we are sure that it will serve you for many years to come.
To optimise the performance of this product, please read these operating instructions carefully to familiarise yourself with the basic
operations of this unit. Please retain them for future reference. This unit has been tested at the factory before being shipped to you.
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. To prevent a fire hazard, do not
expose the unit to any naked flame sources. Unplug this apparatus during lightning storms or if it is unlikely to be used for long
periods of time.
When installing the unit, please ensure you leave enough space around the unit for ventilation. Slots and openings in the unit are
provided for ventilation to ensure reliable operation of the product and to protect it from overheating. To prevent fire hazard, the
openings should never be blocked or covered.
The unit is powered by mains electricity, always handle the power cable by the plug. Never pull out the plug by pulling on the cable.
Never touch the power cable when your hands are wet as this could cause an electric shock. Do not tie a knot in the cable. The
power cable should be placed such that it is not likely to be stepped on. A damaged power cable can cause a fire or give you an
electrical shock. Check the power cord periodicaly, if you ever find that it is damaged, replace it before using the unit again. Contact
your retailer for a replacement.
The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area
where this unit is to be used meets the required written on the unit.
The lightning flash symbol inside a triangle is to alert the user to the presence high voltage within the unit’s enclosure that
may be of sufficient power to constitute a risk of electrical shock to persons.
Caution: to prevent the risk of electric shock, do not attempt to open the unit. No user-serviceable parts inside. Refer all
servicing to qualified service personnel.
The exclamation mark inside a triangle is intended to alert the user to the presence of important operating and
maintenance instructions in the literature accompanying the appliance.
Select the installation location of your unit carefully. Avoid placing it in direct sunlight or locations subject to vibration and excessive
dust. Do not use the unit where there are extremes in temperature (below 41ºF / 5ºC or exceeding 95ºF / 35ºC).
Unpacking and safety Please unpack your new product carefully. Your new product should reach you in perfect condition. Please
check that no damage has occurred during transit. If any damage is found, do not operate your unit. Please contact the retailer you
purchased it from immediately. If there is any damage to the mains cable do not use the device. Always disconnect the unit from the
mains supply when carrying out any cleaning of the unit.
Manufacturer declarations
In compliance with the following requirements: RoHS Directive (2002/95/EU) and WEEE Directive (2002/96/EU).
If this product is ever no longer functional please take it to a recycling plant for environmentally friendly disposal.
CE declaration of conformity
R&TTE Directive (1999/5/EU), EMC Directive (2004/108/EU), Low Voltage Directive (2006/95/EU).
The declarations are available on application from [e-mail]
Before putting the devices into operation, please observe the respective country-specific regulations.
Installation
Unless it has already been assembled prior to shipping, attach the hanging bracket to the unit via the screw holes. Ensure that the
unit is firmly fixed together to avoid vibration during operation. Make sure that the structure that you attach the light to is secure and
able to support a weight of 10 times of the unit’s own weight. Always use a safety cable that can hold 12 times of the weight of the
unit when installing the fixture. The equipment must be fixed by professionals and must be attached in a position that is out of the
reach of unqualified personal.
Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimise light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause
greater accumulation of dirt on the unit’s optics. Clean with soft cloth using normal glass cleaning fluid. Always dry the parts carefully.

Operation
There are three ways to operate this unit:
Auto mode
Sound activated (Sound-to-Light) mode
Via a universal DMX controller
Master/Slave mode / Standalone operation
Auto mode and Sound activated (Sound-to-Light) mode
To operate the unit in either of the above modes, use the Function Setting buttons on the rear of the unit. Start by pressing the Menu
button to select your desired effect from the table below e.g. A1 mode (Auto 1 red), then use the Up and Down buttons to select the
speed of the effect 1-9 (slow to fast). Then press the Enter button to save your changes.
Manual setting mode:
A1 Mode
Red setting
Speed 1~9
A2 Mode
Green setting
Speed 1~9
A3 Mode
Blue setting
Speed 1~9
A4 Mode
White setting
Speed 1~9
A5 Mode
Auto setting
Speed 1~9
A6 Mode
Auto setting (not flash)
Speed 1~9
A7 Mode
Auto setting (flash)
Speed 1~9
S1 Mode
Red setting
Speed 1~9
S2 Mode
Green setting
Speed 1~9
S3 Mode
Blue setting
Speed 1~9
S4 Mode
White setting
Speed 1~9
S5 Mode
Sound active setting
Speed 1~9
S6 Mode
Sound active setting (not flash)
Speed 1~9
S7 Mode
Sound active setting (flash)
Speed 1~9
d Mode
DMX setting (5 channels)
H Mode
DMX setting (6 channels)
Universal DMX controller operation
When using a universal DMX controller to control a chain of units, you have to set the address using the DMX table below.
Master/Slave operation
Multiple units can be linked together in a daisy chain and operated in Master/Slave mode. Please use a 3 pin XLR cable/plug when
connecting multiple units together in Master/Slave mode.
Master unit: select Auto or Sound mode on the Master unit.
Slave units: select DMX mode and set the start address to d001.
In Master/Slave mode please refer to the DMX settings using the table below.

LED digital setting: d001~d512 (5 channels)
CH1
0~255
LED Gobo
CH2
0~100
Single Gobo Select
101~255
LED Gobo Speed
CH3
0~255
Flash
CH4
11~200
Auto DMX
201~255
Sound DMX
CH5
0~255
Auto DMX/ Sound DMX Speed (Slow--Fast)
DMX code setting: H001~H512 (6 channels)
CH1(Lenses 1)
0~15
Off
16~31
Red
32~47
Green
48~63
Blue
64~79
White
80~95
Red + Green
96~111
Red + Blue
112~127
Red + White
128~143
Green + Blue
144~159
Green + White
160~175
Blue + White
176~191
Red + Green +Blue
192~207
Red + Green + White
208~223
Red+ Blue + White
224~239
Green + Blue + White
240~255
Red + Green + Blue + White
CH2(Lenses 2)
0~15
Off
16~31
Red
32~47
Green
48~63
Blue
64~79
White

80~95
Red + Green
96~111
Red + Blue
112~127
Red + White
128~143
Green + Blue
144~159
Green + White
160~175
Blue + White
176~191
Red + Green +Blue
192~207
Red + Green + White
208~223
Red+ Blue + White
224~239
Green + Blue + White
240~255
Red + Green + Blue + White
CH3(Lenses 3)
0~15
Off
16~31
Red
32~47
Green
48~63
Blue
64~79
White
80~95
Red + Green
96~111
Red + Blue
112~127
Red + White
128~143
Green + Blue
144~159
Green + White
160~175
Blue + White
176~191
Red + Green +Blue
192~207
Red + Green + White
208~223
Red+ Blue + White
224~239
Green + Blue + White
240~255
Red + Green + Blue + White
CH4(Lenses 4)
0~15
Off
16~31
Red
32~47
Green
48~63
Blue
64~79
White

80~95
Red + Green
96~111
Red + Blue
112~127
Red + White
128~143
Green + Blue
144~159
Green + White
160~175
Blue + White
176~191
Red + Green +Blue
192~207
Red + Green + White
208~223
Red+ Blue + White
224~239
Green + Blue + White
240~255
Red + Green + Blue + White
CH5(Lenses 5)
0~15
Off
16~31
Red
32~47
Green
48~63
Blue
64~79
White
80~95
Red + Green
96~111
Red + Blue
112~127
Red + White
128~143
Green + Blue
144~159
Green + White
160~175
Blue + White
176~191
Red + Green +Blue
192~207
Red + Green + White
208~223
Red+ Blue + White
224~239
Green + Blue + White
240~255
Red + Green + Blue + White
CH6(Lenses 6)
0~15
Off
16~31
Red
32~47
Green
48~63
Blue
64~79
White

80~95
Red + Green
96~111
Red + Blue
112~127
Red + White
128~143
Green + Blue
144~159
Green + White
160~175
Blue + White
176~191
Red + Green +Blue
192~207
Red + Green + White
208~223
Red+ Blue + White
224~239
Green + Blue + White
240~255
Red + Green + Blue + White
Technical specification & features
Kam LED Bronco
Six lens gobo lighting effect with DMX
Multi-colour RGBW LED effects
Classic disco gobo shape lighting effects
Sound-to-Light mode via built-in microphone
Adjustable microphone sensitivity
Auto/standalone mode / DMX mode / Master/Slave mode
The unit can be operated by DMX512 control or can be used as an individual unit without controller
Four button function setting with LED display
Tough metal chassis / Adjustable metal hanging bracket / Safety chain loop
IEC mains input
Fan cooled operation
Voltage: AC110～240V / 60/50HZ
Power: 80w / Fuse: 3A
LED: 6 x 10w 4-in-1 LED (red, green, blue and white)
Control signal: DMX signal / Channels: 5/24 channels
Dimensions (WxHxD): 430 x 50 x 280mm (not including bracket)
Weight: 3.1Kg