K&m 24140 User manual

3. ASSEMBLY

1. SAFETY NOTES

- Check the mount for damage prior to and after use.

-Do not continue to use damaged mounts.

- Maximum centered load: 35 kg

- not suitable for outdoors or moist rooms.

- please refer to local mounting instructions (may possibly

-deviate from the examples provided in Section 5 A, B, C)

- use 4 screws for the wall mount

- only use trained technicians to assemble the system

- only mount on suitable walls with the corresponding

-assembly material (not included in the delivery)

- walls, that are too weak or have electrical and water conduits

-or the like are unsuitable. In case of doubt consult a qualified

-technician.

- regularly check that the screws are tight and the conditions of

-the parts and components are in working order.

- Careful and attentive handling is required when adjusting the

-loudspeakers, because the adjustment options can result in

-the pinching or wedging of your hand.

- when using the holder at "events and production sites for

-scenic presentations" BGV C1 applies accordingly.

1.1 Pace each cover jon the plates Duntil it clicks in place.

1.2 Place plates through the slit in wall tube C.

1.2 NOTE: Hold the pieces in such a way that the back of the tube and the cover

1.2 form a line AND the round part of the cover faces forward.

1.3 Now slip on the remaining two covers jinto place until they click.

2Hold both corner plates Bto the drill hole on the wall tube Cand screw it

2on using two hexagon screws M8 x 60 hand safety nuts M8 g.

3Connect support tube Ato the wall tube C.

3.1 To accomplish this, place the plates of the support tube in the slits of

3.1 the wall tubes.

3.2 Place two hexagon screws M8x60 hthrough the corresponding drill holes

3.2 in the corner plates Band the support arm and tighten the safety nuts M8 g.

3.3 To accomplish this, use the two open-end or ring spanners SW13

3.3 (not included with the delivery).

4NOTE: The mounting bolt is placed in one of FOUR possible drill holes

4and is not tighten in the pre-mounted state.

4.1 Please select the desired position of the bolt and then screw it tight to support

4.1 tube (A) To accomplish this, hold the screw head at the top with an Allen

4.1 wrench / hexagon key SW8 and tighten the safety nut M10 between

4.1 the disk using an open-end or ring spanner SW17.

5After the installation of the screws, place the protective caps (e-1x, f-8x)

5on the screws.

6The four U-discs iare used as spacers for the wall mount.

2. PARTS - OVERVIEW

Conduct a visual inspection to ensure that all the parts are

included and are in working order.

UNPACKAGED PARTS: ASupport tube with pre-mounted bolts, BCorner plate 2x, CWall tube, DFastening clip 2x

PARTS BAG: e1x Protective cap M10, f8x Protective caps M8, g4x Safety nuts M8-SW13, h4x Hexagon screws M8 x 60 mm-SW13,

i4x U-disks ø8,4/24 mm, j4x Adjustment caps

Thank you for choosing this product. The instructions provide

directions to all of the important setup and handling steps. We

recommend you keep these instructions for future reference.

24140 Speaker wall mount

- Stable model, suitable for loudspeakers up to a max. of 35 kg

- Equally suited for home, object and public areas

- Suitable for flange bushings - internal diameter 36 mm

- The speaker distance to the wall can be individually adjusted in 4 positions

- The wall mount is largely covered by the loudspeakers

The back wall

of the wall tube

and the cover

are flush

The radius of

the cover

in the front

1. The radiuses

are in the back

2. Back walls

2. are not flush

3. Combination

3. of 1. and 2.

OK! Incorrect!

NOTE:

The Safety Nut M10 is only tighten a bit at delivery.

Select the desired position for the fitting bolt (a selection of 4 options are

available) and tighten the nut as described in 4.1.

- without sieve bushing for concrete wall.

- with sieve bushing for perforated bricks.

Advantage: Mounts without the anchors expanding, as such the mount can

be used as often as needed and ensures mounting right up to the edge (not

under 100 mm distance). Please follow the assembly/mounting instructions

provided with the products.

4. WALL MOUNT

6. ABMESSUNGEN

- Place the mount in a vertical position and mark the drill holes

- Drill the anchor holes 4x (ø8 for the bolt anchor; ø10 for frame anchor)

5. MOUNT EXAMPLES

A. Concrete wall, e.g.: Bolt Anchor M8 x 75 mm

- drill hole

- blow out the hole

- hammer in the anchor

- Place the wall mount

- Place the U disk

- Tighten the nut

-(SW13) with 20 Nm

B. Perforated brick, e.g.: Plastic frame anchors 10 x 100 mm

B. with wood screws DIN571 ø7 x 105 mm

C. Suitable for both concrete and perforated brick:

C. Injection molding anchor

- drill hole, blow out the drill hole

- hammer in the anchor

- Place wall mount

- and U-disks

- Screw in the screws (S13)

8. CHECK, MAINTENANCE, CLEANING

FAULT-FINDING (F) and REPAIR (R)

- When using the mount at "events and production sites for scenic

-presentations" BGV C1 applies accordingly.

- In the event of workstation maintenance pay attention to possible risks

-(wedging/pinching, if the product is hit, falling objects etc.) and secure

-accordingly.

- To care for the product use a damp cloth and a non-abrasive cleaning agent.

F: Mounted parts are not stable

F: R: Tighten the screws.

F: Loudspeaker sways back and forth on the locking pin

F: R: Tighten the nut beneath the locking pin 4.1

F: R: Check the loudspeaker, in particular, the internal diameter of the

F :R: connector. This should be between 35 and 36 mm.

7. TECHNICAL DATA / SPECIFICATIONS

Material

Tubes, plates, bolts - Steel, black powdered

Screws, nuts - Steel, galvanized

Cover, caps - PA, PE

Load max. 35 kg

Dimensions H x W x D: 410 x 126 x 360 mm,

Locking pin: ø 35 x 84 mm

Box H x W x D: 65 x 120 x 530 mm

Own weight net: 2.6 kg / gross: 3.0 kg

Accessories Adapter Sleeve 21326 for loudspeakers

with 38 mm internal diameter (US Variant)

KÖNIG & MEYER GmbH & Co. KG

Kiesweg 2, 97877 Wertheim, www.k-m.de

24140-000-55 Rev.07 03-80-339.00 3/16

These mounting accessories may only be mounted and used:

- by qualified personnel familiar with the relevant regulations,

- in accordance with local and state regulations and the regulations for occupational insurance schemes

- as described in the assembly instructions (=installation and operating instructions),

- after a fault-free functional and visual inspection (completeness, operational safety; special attention must be paid to deformations, notches, cracks,

-wear, damage to threads; corrosion and legibility of markings),

- without changing or processing the components,

- indoors (not in damp rooms).

- The installation should be carried out by qualified personnel.

- Depending on the nature of the walls/ceilings and the type of load, fasteners of suitable design and sufficient dimensions must be used.

- In particular take into account the reduced load-bearing capacity of wall and ceiling coverings, facing plywood and insulation panelling.

- The specified tightening torques must be observed for all screw connections. If nothing is specified, the maximum tightening torques for the respective

-screw connection apply.

Box systems must be secured against falling down in the area of stages or studios. A distinction is made between two types of protection:

1. Mobile installation (e.g. flying speakers, installation using C-hooks on trusses, manually detachable fastening elements) requires a second,

1. independently acting safety element on the unit.

2. Stationary mounting allows the second securing element to be dispensed with if the fastening is sufficiently dimensioned and can only be detached

2. with tools plus being protected against self-loosening.

2. Nevertheless, we recommend using a second securing element.

KÖNIG & MEYER GmbH & Co. KG

Kiesweg 2, 97877 Wertheim, www.k-m.de

Rev.02 03-80-900-00 7/20

3. Safety measures

2. General installation instructions

GENERAL SAFETY AND

ASSEMBLY INSTRUCTIONS

MOUNTING ACCESSORIES for overhead installations (e.g. wall, ceiling and truss mounts)

1. General safety instructions

4. Safety factors

Fasteners of loudspeaker boxes are safety-relevant parts that can endanger life and health of people in case of failure. Depending on the country in

which the article is used, the country-specific standards and guidelines for the sector "loudspeakers" must be observed respectively followed.

5. Inspection and maintenance

Overhead mounting is highly security relevant and requires an appropriate awareness of the potential danger. A safety inspection of the mounting

accessories is essential. If damage and/or malfunctions are found on accessories, the product must not be used again until it has been completely

overhauled.

- First of all, a visual and functional check must be carried out before initial operation, paying particular attention to deformations, cracks, wear,

-corrosion, fault-free functioning and the legibility of markings.