KAP ROiK-10 User manual

Instruction Manual
DATE.
www.kaptrade.com
Korea Auto Parts
2019.02.25
ROiK-10
ANDROID NAVIGATION

[ANDROID NAVIGATION] ROiK-10
COMPONENTS
ROiK-10 Power Cable AV Cable
RGB OUT Cable External GLONASS
GPS Antenna MIC
Capacitive Touch Cable Resistor Touch Cable Speaker
WiFi/BT Antenna x 2 LVDS OUT HDMI Cable CVBS OUT Cable

[ANDROID NAVIGATION] ROiK-10
SPEC
※ ANDROID
OS
CPU
VPN
Memory
USB
USB
3.0
Wireless
GPS
Touch
RGB OUT
LVDS OUT
CVBS OUT
HDMI OUT
Speaker
I/O
Input Power
Temperature
Operating
Android
7.1.2(Nougat)
Six
-Core 64bit Server Class Cortex-A72 Core @2.0Ghz,
Mali
-T860 Quad-Core GPU (Total Ten-Core)
H.264/H.265/VP9 up to
4Kx2K@60fps (4K Video)
2GB
DDR3
USB2.0 High Speed Port x 2
USB3.0
5.0Gbps Port x 1
2.4GHz/5GHz
Dual-Band WiFi,
Support 802.11a/b/g/n/ac, Bluetooth 4.1
Ublox8
GPS
(GLONASS/BEIDOU/GALILEO/QZSS/SBAS)
Resistor/Capacitive touch
1280x720
video IN -> 800x480 OUT or 480x234 OUT
(RGB
Scale adjustment)
1280x720
video IN -> Digital 800x480 LVDS OUT
(LVDS
Scale adjustment)
1280x720
video IN -> CVBS OUT
HDMI 2.0, Support maximum
4K@60Hz display
2W
Stereo
Audio Out, Mic (voice recognition),
CVBS Out(On LVDS Out)
DC 8V ~ 24V
-
20°C ~ 80°C
-
15°C ~ 70°C

[ANDROID NAVIGATION] ROiK-10
DIGITAL LVDS OUT
800x480
(Block RGB Signal)
CVBS OUT
Use UART or
Resistive Touch
RGB 800x480
Use Capacitive
Touch
(GOODIX GT9XX)
RGB 480x234
GPS Power Self
(Use car GPS Cable
–Option)
GPS Power from
ROiK-10
(Use External
GLONASS GPS
Antenna –MUST ON)
DIP S/W INFORMATION
ON OFF
Pin No.
ON OFF
SW - 1 ANALOG RGB OUT DIGITAL LVDS OUT / CVBS OUT
SW - 2 GPS Power from ROiK-10 GPS Power Self
1 2
ON
1 2
ON 1 2
ON
ON OFF
Pin No. ON OFF
Mode SW - 1 Capacitive Touch
Resistive Touch, UART Touch
Mode SW –2
(SW –1 switch is ON) RGB 480x234 Output RGB 800x480 Output
Mode SW –3
(SW –1 switch is OFF) Interface Using tw8836 Normal
Mode SW - 4 1200x720
(Same Ratio 800x480) - Default 1280x720
1 2
ON 3 4
1 2
ON 3 4 1 2 ON 3 4
1 2
ON 1 2 ON 3 4
1 2
ON 1 2 ON 3 4
1 2
ON 1 2 ON 3 4
1 2
ON 1 2 ON 3 4
1 2
ON 1 2 ON 3 4
1 2
ON 1 2 ON 3 4
1 2
ON 1 2 ON 3 4
Mode SW
SW

[ANDROID NAVIGATION] ROiK-10
CONNECTOR PIN ASSIGNMENT –POWER / AV
CONNECTOR PIN ASSIGNMENT –RGB OUT / CVBS OUT
12 3
123
Yellow Black Red
BATTERY Power GND ACC 12V IN
POWER
1357911 13 15 17 19 21 23
2 4 6 8 10 12 14 16 18 20 22 24
Power Cable
(POWER/CAN)
AV Cable
(AV IN/OUT)
1357911 13 15 17 19 21 22
White Red White Blue White Yellow Black Green Red Green
Speaker +
AUX OUT R
AUX OUT L
Capacitive
Touch SCL
Capacitive
Touch SDA
Capacitive
Touch
Interrupt
Touch X- Touch X+ UART TX UART RX NC NC
246810 12 14 16 18 20 22 24
Black Black Black Black Red Green White Red White Black Black
Speaker - GND GND GND
Capacitive
Touch 3.3V
Capacitive
Touch Reset
Touch Y- Touch Y+ MIC + MIC - NC NC
AV/IN OUT
RGB OUT DIP S/W
1 2
ON
123456 7
RGB OUT Cable
(RGB OUT)
1 2 3 4 5 6 7
Red Green Black White Black
Red Green Blue C-Sync GND NC NC
1 2
ON
123456 7
CVBS OUT Cable
(RGB OUT)
1 2 3 4 5 6 7
White White Black
CVBS CVBS NC NC GND NC NC

[ANDROID NAVIGATION] ROiK-10
SCREEN VIEW
※ Screen Size : 1280px X 720px
※ This icon will show when Dip s/w set to use “Resistive Touch” ,
or it will show car have a resistive touch. automatically
※ Screen Size : 1578px X 584px

[ANDROID NAVIGATION] ROiK-10
SCREEN VIEW
1NAVIGATION Quick icon for Navigation Application
2Multimedia Quick icon for Multimedia Application
3Music Player Music player Widget
4File Manager Quick icon for File Manager Application
5APPS Application List
6Back Button Return
7Home Button Home
8Multitasking 1. Multitasking
2. PIP Mode by Long Press
9APP Shortcut Quick icon
10 Sound Volume control
11 WiFi Open Wifi setting screen
12 Settings Open Android Settings
13 Zoom Tool Screen Zoom in / out
1 2 3
4 5
6 7 8 9 10 11 12
13

[ANDROID NAVIGATION] ROiK-10
SCREEN VIEW –Split Screen Mode
Long
Press
Normal
Mode
Split Screen
Mode
※ Split Screen
1. Press and hold the multi-tasking button to enter the split screen mode.
2. In the split screen mode, press center to reverse the direction.
※ Some apps are not work on Split Screen Mode
1
1
2
2Press center : Reverse left to right

[ANDROID NAVIGATION] ROiK-10
CABLE CONNECTION
ANDROID
NAVIGATION
POWER UART LVDS OUT RGB OUT AV IN/OUT SW GPS WIFI/BT
DEBUG
MODE SW R-KEY USB3.0 T-KEY HDMI OUT USB2 USB1 MicroSD
HEADREST MONITOR
[CVBS]
WiFi/BT
Antenna x 2
+ -
Car battery
ACC
12V
KAP
Interface
Digital
LVDS
Interface
USB
A-A
Cable
VIDEO
INTERFACE
RGB IN
OR
GPS
Antenna
CAP - Touch
RES - Touch
UART - Touch
MIC
SPEAKER
AUX OUT R
AUX OUT L
INTERFACE

[ANDROID NAVIGATION] ROiK-10
CABLE CONNECTION
ANDROID
NAVIGATION
POWER UART LVDS OUT RGB OUT AV IN/OUT SW GPS WIFI/BT
DEBUG
MODE SW R-KEY USB3.0 T-KEY HDMI OUT USB2 USB1 MicroSD
※ Play movies or music
using USB or Micro-SD Card
※ Firmware update is
available only by “USB1”
HEADREST MONITOR
[HDMI]

[ANDROID NAVIGATION] ROiK-10
Resitive
Touch panel
CABLE CONNECTION –Interface Resistive Touch
Use Resistive Touch
※ Digital LVDS OUT/CVBS OUT
DIP S/W 1 = OFF
※ Resistive Touch
DIP S/W 1 = OFF
1 2
ON 3 4
ANDROID
NAVIGATION
POWER UART LVDS OUT RGB OUT AV IN/OUT SW GPS WIFI/BT
DEBUG
MODE SW R-KEY USB3.0 T-KEY HDMI OUT USB2 USB1 MicroSD
DIGITAL LVDS
INTERFACE
LVDS IN
RGB
INTERFACE
RGB IN
1 2
ON
1 2
ON
※ RGB OUT
DIP S/W 1 = ON
OR

[ANDROID NAVIGATION] ROiK-10
CABLE CONNECTION –Interface Capacitive Touch
Use Capacitive Touch
(Goodix GT9xx)
※ Digital LVDS OUT/CVBS OUT
DIP S/W 1 = OFF
CAP TOUCH EXT
※ Capacitive Touch
DIP S/W 1 = ON
1 2
ON 3 4
ANDROID
NAVIGATION
POWER UART LVDS OUT RGB OUT AV IN/OUT SW GPS WIFI/BT
DEBUG
MODE SW R-KEY USB3.0 T-KEY HDMI OUT USB2 USB1 MicroSD
DIGITAL LVDS
INTERFACE
LVDS IN
RGB
INTERFACE
RGB IN
Capacitive
Touch Panel
CAP
TOUCH
1 2
ON
1 2
ON
※ RGB OUT
DIP S/W 1 = ON
OR

[ANDROID NAVIGATION] ROiK-10
OR
CABLE CONNECTION –Interface UART Touch
ANDROID
NAVIGATION
POWER UART LVDS OUT RGB OUT AV IN/OUT SW GPS WIFI/BT
DEBUG
MODE SW R-KEY USB3.0 T-KEY HDMI OUT USB2 USB1 MicroSD
ROiK UART RX connect with UART TX
ROiK UART TX connect with UART RX
TX
RX
UART TX
UART RX
GND
Use UART Touch
※ UART Touch
DIP S/W 1 = OFF
1 2
ON 3 4
DIGITAL LVDS
INTERFACE
LVDS IN UART TX
RGB
INTERFACE
RGB IN
Cut the USB-Cable
Connect white-cable
of USB-Cable to the
interface.
1
2
Use one or two methods
depend on protocol
12

[ANDROID NAVIGATION] ROiK-10
TOUCH SETTING
1. Capacitive Touch Setting
※ DIP S/W 1 = ON : Capacitive Touch Goodix GT9xx Model
2. Select Touch Panel name
If don’t have on the list, select “OTHER STORAGE”
3. OK 4. Select setting file (saved on USB/SD)
On the list Not on the list
※ Tab “Select Interface” to change type of interface.
Capacitive Touch Setting (GOODIX GT9xx)
UART Touch Setting (USB Conection)

[ANDROID NAVIGATION] ROiK-10
CABLE CONNECTION –HEADREST MONITOR
ANDROID
NAVIGATION
POWER UART LVDS OUT RGB OUT AV IN/OUT SW GPS WIFI/BT
DEBUG
MODE SW R-KEY USB3.0 T-KEY HDMI OUT USB2 USB1 MicroSD
※ Headrest Monitor (CVBS or HDMI)
CVBS HDMI
INTERFACE
OR

[ANDROID NAVIGATION] ROiK-10
No. Button Function
1RESET SETTINGS Reset settings to default
2RESTART DEVICE System Reboot
3External Speaker Turn on/off external speaker
4Softkey Enable Use soft key or disable (Floating button when disabled)
5Softkey Position Soft key position setting (side, bottom)
6Softkey Auto Hiding Set softkey auto-hide time
7Zoom Button Enable Enable or Disable the Zoom Button on the Soft Key
8Startup App Select Startup APP
9Select Interface Select Manufacturer of Connected Interface
10 Cooling Fan Turn on / off Cooling Fan
11 HDMI OUT Turn on / off HDMI Out
12 Digital Out Settings (Developer menu) DIGITAL LVDS only,
Screen Settings - Position, Brightness, Contrast, Sharpness
13 CVBS Settings (Developer menu)
Screen Settings - Brightness, Contrast, Sharpness
14 FMT Settings Select FM transmitter frequency
15 Touch Calibration Touch Calibration ( for UART Touch )
16 Set User Boot Logo File Format : PNG, JPG, BMP
Image Size : 1280 X 720 pixel
17 Upgrade Device (Hidden menu) Firmware update is available.
DEVICE SETTINGS

[ANDROID NAVIGATION] ROiK-10
DEVICE SETTINGS –Softkey / Floating Button Settings
1. Softlkey Use
Floating Button Enble Using or not using floating button
Transparent Adjust the transparency of floating buttons
Automatic Hide Floating button auto-hide setting
Automatic Close Floating button auto-hide setting time
2. Floating Button Use (Disable Softkey)

[ANDROID NAVIGATION] ROiK-10
DEVICE SETTINGS –Select Interface
Touch Data is different for each manufacturer,
so you should choose the right manufacturer.
If you do not know the manufacturer, please contact us at [e-mail]

[ANDROID NAVIGATION] ROiK-10
DEVICE SETTINGS - FMT Settings
1. FMT Settings
2. Press 'OFF' in the FMT Setting screen.
3. Setting

[ANDROID NAVIGATION] ROiK-10
DEVICE SETTINGS –CALIBRATION (RESISTIVE TOUCH)
Press and hold the center of '+‘, 5 times.
Calibration mode
※ Capacitive touch panel no need set calibration
B. Push button 2~3 sec after booting
Set User Boot Logo Activate
1. Device Setting
2. Click ‘Set Use Boot Logo’ and select boot logo image.
A. Device Settings > Touch Calibration
A
B
DEVICE SETTINGS - USER LOGO UPDATE
※ File Format : PNG, JPG, BMP
※ Image Size : 1280px X 720px