KAPLAN 48085 User manual

Qty. 12 cam locks
Qty. 12 pin connection bolt
Qty. 6 1.5” wood screw
Qty. 25 7 x 50 hex head screw
Qty. 14 wood dowel
Qty. 16 3/4” wood screw
Qty. 8 single hook
Item # 48085 - 4 Section Coat Locker
Assembly Instructions
Hardware Components List
Parts List
Qty. 1 left side Qty. 1 right side
Qty. 1 top Qty. 1 bottom
Qty. 1 top notched shelf Qty. 1 bottom shelf
Qty. 2 toe kicks Qty. 4 top back panels
Qty. 1 bottom back panel Qty. 3 long dividers
Qty. 3 short dividers
You will need 1 Allen wrench (provided), and 1 Phillips head screwdriver to assemble

Step 1
Attach short bottom dividers to the
bottom. Place the bottom
with the unnished side facing you,
and the end with the groove for the
back panel towards the table.
Step 2
Using 6 hex head screws, attach the
short dividers, with the round edge
facing up. Using the allen wrench,
tighten the hex head screws clockwise
until snug.
Step 3
Attach the 2 toe kicks to the bottom.
Insert a 1.5” wood screw thru the
pre-drilled hole in the middle of the
toe kick, and into the pre-drilled hole on
the bottom. Using a Phillips head
screwdriver, tighten clockwise. At this time,
only do the middle screw. We will come
back to nish the rest in a later step.
Step 4
Insert 6 wood dowels into the
pre-drilled holes on the top of the
short bottom dividers.
*you may need to use a hammer to tap
dowels in if they are tight.

Step 5
Place bottom shelf on top of the
dividers, and line up dowels with the
corresponding dowel holes on the
bottom of the shelf. Push shelf down
until ush on dividers. Using 3 hex head
screws, attach the shelf to the dividers
with the allen wrench.
Step 6
Slide the bottom back panel
into the back panel groove in
between the bottom and
bottom shelf.
Step 7
Using a Phillips head screwdriver,
install 6 pin connection bolts into the
plastic insert on the top of the
bottom shelf. Tighten clockwise
until snug.
*do not over tighten
Step 8
Attach 6 single hooks to the 3 long
dividers. Install 1 hook to each side
using 2, 3/4” wood screws per hook.

Step 9
Slide the 3 long dividers onto the
pin connection bolts. Make sure the
groove for the back panels is towards
the back of the unit.
Step 10
Using 6 cam locks, secure the dividers
to the bottom shelf, using two cam
locks per divider. Tighten clockwise until
snug, about 1/2 a turn.
Step 11
After dividers are secure, slide 2 top
back panels into the back panel grooves
of the two middle sections of the dividers.
Step 12
Slide the top notched shelf into the
matching notches on the dividers.
If the shelf is a little tight, you can lie the
unit on its back, and tap the shelf into
place using a rubber mallet.
*Do not use a hammer, as this will
damage the edge of the shelf.

Step 13
Install 6 pin connection bolts into the
plastic inserts on the underside of the top
shelf. Tighten bolts clockwise until snug.
*Do not over tighten
Step 14
Place top shelf on top of the dividers,
and line up pin connection bolts with
pre-drilled holes on top edge of dividers.
Push into place until top shelf is
ush against top of dividers.
Using 6 cam locks, secure the dividers
to the top shelf, using two cam
locks per divider. Tighten clockwise until
snug, about 1/2 a turn.
Step 15
Step 16
Attach 2 remaining single hooks to
the left and right side panels using
2, 3/4” wood screws per hook.

Step 17
Slide the remaining 2 back panels
into the back panel grooves on both
ends on the unit.
Step 18
Insert wood dowels into the middle
pre-drilled holes on the ends of each
of the shelves. 4 on the right side,
and 4 on the left side.
*You may need a hammer to tap dowel
into place if dowel is to tight.
Step 19
With the end of the unit hanging o
the edge of the table, place the end
panel against the side of the unit, and
line up the dowels, with the corresponding
dowel holes on the end panel.
Step 20
When the end panel is ush against
the edges of the shelves, you can secure
the end panel in place with 8 hex head
screws. Using the allen wrench, tighten
screws clockwise until snug.
Repeat steps 19 and 20 for opposite side.

Step 21
Lie the unit on it’s back, and install
the 4 remaining 1.5”wood screws into
the toe kicks, as in Step 3.
Stand unit up.
*You may need some assistance lifting this
unit, and practice proper lifting techniques.
Congratulations!
You have now completed assembly on your new
4 Section Coat Locker.