Kelkay 45012L User manual

Easy Fountain Instructions
45012L - Slate Crag Falls
STAGE 1
Position the base section of the feature onto a secure and level location.
STAGE 2
STAGE 3
STAGE 4
STAGE 5
STAGE 7
Thread the transformer wire through the access cavity and push the cable with 2 pins into the
transformer and screw over the plastic collar.
STAGE 6
Fill the fountain with sufficient water to ensure that the pump is fully submerged.
Please read the assembly and pump operating instructions carefully and observe the safety
instructions.
Following the diagram above, fix the top section onto the base of your water feature and lock it into
place.
Following the diagram above reach into the access cavity at the back of the water feature and
carefully bring out the LED light cables and the internal water pipe.
Connect the plug to your mains outlet.
The transformer should never be submerged or stood in water.
Please note the transformer will get hot while in use, this is normal.
Connect the LED light cables that from the inside of the water feature to the cables which extend
from the water pump. Connect the internal water pipe onto the pump outlet.
ELECTRICAL SAFETY: If outdoors the outlet must be
waterproof. We recommend the use of a residual current device
(GFI) Ground Fault Interrupter (available from all good D.I.Y.
stores) when connecting the fountain to the electric supply.
PUMP FLOW: The pump flow
can be adjusted with the
regulator, this is found on the
inlet of the pump. We
recommend starting with the
flow regulator fully open and
then adjusting down if required.
www.kelkay.com

easyfountain®
Aftercare Information
www.kelkay.com
• Clean and top-up the water on a regular basis.
• To empty the fountain of water for cleaning or for
winter care:
Smaller fountains (that are light enough to be lifted)
the water can be emptied by simply inverting the
fountain and letting the water pour away through a
suitable drain or sink.
Larger (heavier) fountains - water can be removed
by using a large sponge or by purchasing a simple
syphon pipe available from aquatic supply stores.
• Always shut off the power before cleaning and
maintaining the fountain or pump.
Please note: The easyfountain®aftercare range is only available in the UK
and Republic of Ireland. Please check with your nearest stockist for availability.
Caring for your fountainCleaning your fountain
Troubleshooting
Winter care
The easyfountain®aftercare range includes products to
help care for your fountain. Please see the table below
for more information.
Fountain Algae Stopper 385g
• Easy to use
• Removes and prevents algae and bacteria
• Will not harm animals and birds
Fountain Grime and Lime Cleaner 500ml
• Easy to use
• Removes dirt from your water feature
• Limescale buster
Fountain One Shot Algae Remover 100g
• Easy to use
• Removes algae and bacteria
• Stops slime build up
Fountain Citronella Water Scent 125ml
• Easy to use
• Clean and fresh scent
• Helps to repel insects
Fountain Shine Spray 500ml
• Easy to use
• Helps preserve radiance
• Leaves a smear free shine
Guidelines to help protect your easyfountain®:
• If possible, bring your water feature indoors
eg. garage or shed.
• Drain the fountain of all water. If water freezes within
the fountain, this can cause damage.
• If your fountain is left outside and drained of all water,
a Kelkay easyfountain® cover can be purchased to
cover the entire fountain however we cannot
guarantee that it will protect your fountain from
winter damage.
Pumps
• Check the water is covering the pump by at least 5cm.
• Check the flow dial on the pump to ensure the correct
“flow” for the fountain is set.
• Check to see if it is running if it is then it is probably
blocked.
• Clear the pipe and impeller from blockages.
• Check the fuse in the plug.
Lights/Transformers
• If the lights and the pump are not working it is likely the
transformer has failed. If the product is within the
warranty period and misuse has not occurred a
replacement part can be issued providing a proof of
purchase is supplied.
• Flickering lights are caused by a build-up of algae and
lime scale on the connectors between the transformer
and the lights. This is not covered by the warranty.
Replacement parts can be purchased from Kelkay LTD.
• If the lights stop working they are available to purchase
from Kelkay LTD. Light bulbs are not covered under
the warranty.
• Individual L.E.D lights are not replaceable but can be
replaced as a set.
Leaks/Loss of Water
• Overfilled - make sure the water reservoir is not
overfilled. Remove water if necessary.
• Pump Flow Rate - check the pump and reduce the
flow rate if required.
• Level - ensure the fountain is completely level.
• Natural evaporation, weather elements and wildlife
will also affect the fountain water level on a daily
basis. Top up your fountain as required.
Main Body & Paintwork
• Do not confuse limescale residue with fading paint -
this is not a fault and in most cases the fountain
needs cleaning.
• Paint peeling will occur if the fountain has been left
outside in the frost and will not be covered by the
warranty.
• Parts broken off the main body while in use are
usually caused by bad weather conditions and not
covered by the warranty.

Easy Fountain Instructions
45012L - Slate Crag Falls
Box Contents
www.kelkay.com