Kellfri 13-KW340 User manual
Read this manual carefully
before using the product!
Translated from the original
2018-10-23
13-KW340
LOG CUTTER AND SPLITTER
ELECTRIC-POWERED
Table of contents
TABLE OF CONTENTS
Introduction 3
Product information 3
Use of product 3
Technical specication 3
Safety information 4
Safety warnings 5
Incase of emergencies 5
Personal protection 5
Surroundings 6
Warning Symbol 6
Electric chainsaw 7
Technical information 13KW109 7
Product safety information 8
Chain brake 9
Starting the engine 10
Installing new chain 10
Stopping the engine 11
After use 11
Safety measures before operating 12
Operating the machine 13
Phase inverter 13
Cutting and splitting of wood 14
Transport and storing 15
Maintenance and service 15
Service 16
Recycling 16
13-KW340 spare parts 17
Spare part - chainsaw 19
Installation instructions 20
How to mount the chainsaw on themachine 21
Electrical diagram 22
Complaint form 23
EC-declaration of conformity, original 24
Table of contents
Kellfri AB is constantly working to further develop its products, and therefore reserves the right to make changes
to, among other things, design and appearance without prior notice.
INTRODUCTION
Thank you for choosing a product from Kellfri AB. By following the general safety information,
instruction manual and common sense you will get many years of enjoyable use of the prod-
uct. Kellfri’s tools and machines are aimed for farmers with high demands on functionality.
PRODUCT INFORMATION
KW430 Combined machine is equipped with a electic chainsaw, Bar Oregon and Oregon
Chain, The chainsaw can handle up to 34 cm thick logs. The machine can split logs into 2 or 4
pieces. The height of the knife is adjustable. The machine is equipped with a hitch and 3 phase
inverter as standard.
The electric chainsaw must be connected to a separate 230 V outlet.
USE OF PRODUCT
Only for cutting and splitting logs. The machine is for outdoor use only.
TECHNICAL SPECIFICATION 13KW340
Cutting diameter 340 mm
Cut length min - max 150 - 600 mm
Compression Force 7 tonnes
Engine 4 kw
RPM 1400 rpm
Fuse 16 amp
Hydraulic oil tank 35 l
Oil ow 26 l/min
Electric saw 2,2 kW
Blade length 400 mm
Chain 3,25
Wheel 600-9
Towing 50 mm coupling
Three-phase with the phase inverter Standard
Length x Width x Height 3000 x 1100 x 1250 mm
Danger! The machine can be dangerous when used incorrectly. Therefore,
it is required that the operator has sucient knowledge about the machine
how works, all functions and how to operate it.
Table of contents
SAFETY INFORMATION
Before using the product, please read the safety information and instruction manual and un-
derstand its contents for your own and others’ safety. Always keep the safety information and
instruction manual easily accessible to the user of the product. Remember that it may be good
for your own and others’ safety to read the safety information every now and then. If the in-
structions manual is damaged or otherwise unusable, please contact and order a new one
from: Your retailer
The general safety instruction is also available from Kellfris website: www.kellfri.co.uk
Do not use this equipment if you are feeling sick, tired or in inuence of alcohol. Nor if you
are under the inuence of strong medications or drugs, suering from strong depression or
severe mental illness. Always follow the general trac rules and regulations and the rules of
the Animal Welfare Act. Persons under 15 years old and people with mental illness may not
use these product.
WARNING!
The machine’s original design must not under any circumstances be changed without the permission of the manufacturer.
Unauthorized modications and / or accessories can result in life-threatening or fatal injury to the operator or others.
Kellfri disclaims all responsibility for self-made modications and alterations
Danger!
CAUTION!
Note!
Warning!
This symbol indicates that a serious accident will occur if the instructions in the manual is not followed.
The accident resulting in serious injury, possibly death or serious property damage.
This symbol indicates that an accident will occur if the instructions in the manual is not followed. The
accident resulting in serious injury or property damage.
This symbol indicates that an accident could occur if the directions is not followed.The accident resulting
in personal injury or property damage.
NOTE! indicates the potential for machine breakdown of the regulations is not followed.
Warning symbols identify important safety aspects in this manual to help you and others avoid hazards and ac-
cidents. When using the machine: Take extreme caution!
When using the machine in a company, the employer has the responsibility to ensure the user of the
machine has theoretical and practical knowledge of the machine and the operation is done safely.
Follow the country’s Health and Safety regulation. For more information, contact your Health and
Safety Executive.
Table of contents
SAFETY WARNINGS
* Read the manual carefully before using the machine.
* The machine should only connect on 3-phase 400V grounded outlet. The outlet shall be
installed by a qualied electrician.
* For your own and others safety, make sure that circuit breaker is installed.
* Keep working area free from other people. Moving parts increases the risk of accidents.
* Do not use or store the machine on a place exposed to rain or moisture.
* Make sure the working area is well lit.
* Do not use electrical equipment near inammable gases or liquids.
* Children must never be present within the work area, never let children handle machines,
tools or extension cords.
* Use the machine only within the capacity it is meant for. Do not increase the capacity of the
machine!
* Stand rmly, never bend over the machine when it is running.
* Check the cords and extension cords periodically, to ensure that no damage has occurred.
* Unplug the power cord when the machine is not in use and during maintenance/service.
* Make sure the power switch is turned o (OFF) before power is connected.
* Never overload the machine.
* Do not move the machine whilst it is running.
* Never leave the machine unattended whilst it is running.
* Do not allow any person to be near the chainsaw when starting and stopping.
* Keep bystanders and animals out of the workplace.
* Keep away all body parts from the chainsaw when it is running.
* Never use the chainsaw if it is damaged, improperly installed or not correctly set.
* Make sure that the chain stops moving when you release the button.
Warning!
For safety, this product should only be used in the manner described in this man-
ual.The user is responsible for the instruction to be read through and followed.
INCASE OF EMERGENCIES
In case of an emergency please dial 999.
Keep cell phone or emergency phone available specially when working alone. First aid kit and
re extinguishers must be kept easily accessible during all work, maintenance and service.
PERSONAL PROTECTION
Always wear suitable clothing and footwear. Do not wear loose clothing or jewelry when using
the machine. Remember to put up long hair when operating machines with rotating parts.
Wear protective gloves, to prevent burn injuries on contact with hot surfaces such as exhaust
system, and to avoid oil and gasoline on the skin. Hearing protection should be used when
the engine is running.
Table of contents
SURROUNDINGS
Make sure your working area is clear from people, children and objects before attaching, con-
necting and using the machine. Risk of serious injuries can occur during operation. Take an
extra caution when children are in the area where the equipment/ product is being use or
stored. Check the area for low hanging electrical wires. Be careful when working on slopes and
near ditches.
Always work alone with single - purpose products such as this product. Never have junk lying
in your area. Keep working areas clean. Always respect the risk zone.
Danger! Children in the area should be supervised.
WARNING LABELS
Make sure that the warning labels are always visible, clean the warning labels if necessary. Do
not wash with high pressure washer directly on the warning label. If any part of the decal is
worn or label becomes frayed or otherwise unreadable, order new decals.
WARNING SYMBOL Explanation
Read the user manual! Before starting the operation.
5m
Warning! Prohibition of staying in the risk area! Risk zone 5m! No one is
allowed in the vicinity of the machine during operation
WARNING! Children are not allowed in the work area!
Warning crushing hazard!
Risk for serious injuries
Warning! Electrical power lines. Keep sucient distance from electrical
power lines.
In the case of electric faults, contact a qualied electrician
The machine is inteded for single purpose use only
Warning! rotating knives!
The product is CE-marked
Table of contents
ELECTRIC CHAINSAW
1
3
4
56
2
1. Start / Stop Switch
2. Immobilizer
3. Hand guard
4. Chain
5. Guide bar
6. Oil tank cap
TECHNICAL INFORMATION 13KW109
Max power 2,2 kW/3 hp
Cutting length 16 "(mm) 400
Oil, Volume (ml) 270
Blade size (in) 16"
Chain pitch (in) 3/8”
Chain spåvidd (in) 0,058"
Weight 5,5 kg
Warning!
The machine can be dangerous when it
is use carelessly or incorrectly . This can
cause serious injury or even death.
DANGER!
Be aware of kickback!
Förbidden to use the machine when
it’s raining and in bad weather
Switch o and unplugg whenever
you leave the machine
CE-label
Read the instruction!
Always use safety guards
Loud sound coming from the
machine. use hearing protection
Table of contents
PRODUCT SAFETY INFORMATION
• Before using the product for the rst time, you should know how it works. If it is possible ,
learn the proper use of the machine from a person with experience.
• Do not use in conditions such as; rainfall, thunderstorms and strong winds, or when the
weather conditions make it unsafe to use this product.
• Do not allow other person to be near the chainsaw when starting and stopping it.
Keep bystanders and animals out of the working area.
• Keep all body parts away from the saw when the engine is running.
• Before starting the engine, make sure that the saw is not in contact with any objects.
• Do not use a chainsaw that is damaged, improperly adjusted or not correctly installed.
• Make sure that the chain stops moving when the throttle is released.
• Follow the instructions in the manual on how to start a chain saw and make sure to hold the
chain saw with a rm grip on the handles.
• Keep handles dry, clean and free from oil. A chainsaw should never be carried around with
the engine running.
• When transporting your chain saw you must use appropriate protective guards which
should be provided for the guide bar or chain.
• Protection against kickback hazard. Kickback occurs when the bar makes an upward move-
ment. This occurs when the chainsaw, at the front of the bar, come into contact with an
object. Kickback can cause you to lose control of the saw and can be very dangerous.
• A chainsaw is intended to be use with two hands. Careless use of the chainsaw can result a
serious injury to the operator, helpers, and / or by standers.
• Pull the cover (Fig. 1) towards the front handle to check that the chain brake is not activated.
• Remove the screw-nuts (A) and the chain guard (B) (Fig. 2)
• Remove and discard plastic spacers from the pins (C) (3)
• Move chain tension pin (D) all the way to the gear (E) (Fig. 3) using chain tension screw (L)
(Figure 5).
• Place the bar (F) on the pins so that tension pin (D) ts into the groove (G) (Fig. 3)
• Install the chain (H) on to the gear (E) and around the guide bar (M) (Fig. 4)
• Pay attention to the chain direction (Fig. 6)
• Reinstall the chain guard and nuts, but do not tighten them completely.
• Thighten the chain using by turning tensioning screw (L) (Figure 5)
• Keep the top of the bar upwards and tighten the nuts completely on the chain guard (Fig. 7).
• The chain should be taut but still can move (Fig. 8)
• The chain is correctly tensioned when it can be pulled up by a few millimeters (Figure 8)
Table of contents
BEFORE OPERATING
• Check the working area, the object to be cut and the cutting direction.
• Before you begin cutting, make sure that the working area is cleared.
• Take care and keep bystanders and animals away from the area within 5m in diameter.
• Makesurethemachineisnotwornout,havelooseordamagedparts.Donotuseifdamaged,
incorrectly, or if not installed correctly. Make sure the sawchain stops moving when the
throttle is released.
CHAIN OIL
Use lubricating oil intended for the chain saw.
Use of proper lubricating chain-oil when cutting limits wear to a minimum between the chain
and the guide bar. This prolongs the life of the product. Always use oil of good quality.
NOTE! Never use discarded oil. Always use a biodegradable environmentally friendly lubricant
designed for bar and chain, gentle both to nature and chainsaw parts.
HAND GUARD
This saw is equipped with a chain brake that stops the chain in the event of a kickback. You
must check the chain brake before each use by running the saw at full throttle for about 2
seconds and pushing the front hand guard forward.
The chain should immediately stop the engine at maximum speed. If the chain stops too slow-
ly or does not stops at all, the brake band and clutch drum must be replaced before the saw
can be used again. It is essential that the chain brake is properly checked before each use and
that the chain is sharpened to maintain security on this saw.
Removal of safety equipment, inadequate maintenance or incorrect replacement the bar or
chain may increase the risk of serious injury due to kickback.
CHAIN BRAKE
The machine is equipped with an automatic brake that stops the chains rotation when kick-
back occurs. The brake system is automatic and controlled by a mechanical force responsive
to the weight of the front shield.
This brake can also be controlled manually with the front hood that folds down to the bar.
Release the brake by pulling up the front guard toward the handle until a “click” is heard.
NOTE! BE THOROUGH WITH THE DAILY INSPECTION OF THE BREAK.
Checking the chain break:
• Turn o the engine.
• Hold the saw horizontally and let go of the front handle, let the guide come in contact with
a tree stump or similar object and check that the brake is activated. Operating levels vary be-
tween dierent bar sizes. If the brake does not work, you must submit the saw for inspection
and repair to your nearest dealer. The engine can be at high rpm for extended periods because
of warmed up clutch which can lead to problems. When the brake is activated during opera-
tion, you must immediately release the throttle.
Table of contents
Never touch the chain while the engine is running.
Before using the machine you must read the sections entitled “SAFETY” and “PRODUCT IN-
FORMATION”. We recommend that you start by practicing sawing smaller logs. This also helps
you to learn the proper use of the chainsaw.
Always follow the safety rules. The chainsaw must only be used to cut wood. It is forbidden
to cut any other types of materials. Vibrations and kickback vary between dierent materials
and the requirements for safety are not met by cutting into other materials. Do not use the
chainsaw as a lever to lift, move, or to share objects. Lock it in xed positions. It is forbidden to
assemble the tools or attachments that are not specied by the supplier.
It is not necessary to force the chainsaw to cut the log . Apply only light pressure while the
engine is running at full throttle. Do not try to pull out the chain saw with violence if it gets
stuck in the cutter, but use a wedge or a skewer to break up the log.
STARTING THE ENGINE
Plug the saw’s power cord into an outlet. Start the chain saw by pressing the throttle. Always
hold the saw rmly with both hands when the engine is running. Use a rm grip with thumbs
and ngers around the handle. Keep all body parts away from the machine while the engine is
running. Before starting the engine, make sure that the chain is not touching anything.
INSTALLING NEW CHAIN
New chains are stretched out and must be adjusted periodically. Adjusting the chain should
only be done when the chain is cold. First lubricate the chain and bar with oil, then start the
chain saw and put it on it’s average speed. Make sure the oil pump is working properly. Stop
the engine and adjust the chain’s tension. Start the saw again and make a pair of cut on a log
to warm up the chain. Stop the engine and let the chain cool and adjust again. Repeat this
process until the chain gets the right tension. Do not touch the ground with the chain.
DANGER!
CHECK THE OIL PATTERN
Start the engine and drive chain on the average
speed and see if the oil is spreading as shown in
the picture
Table of contents
CHECK THE OIL PATTERN
STOPPING THE ENGINE
Warning!
WARNING: Kickback may occur when the nose or tip of the guide bar touches an object, or
when the wood closes in and pinches the saw chain in the cut.Tip contact in some cases
may cause a lightning fast reverse reaction, kicking the guide bar up and back towards the
operator. Pinching the saw chain along the top of the guide bar may push the guide bar
rapidly back towards the operator. Either of these reactions may cause you to lose control of
the saw which could result in serious injury to user.
Release the throttle
Ventilation
AFTER USE
Turn o the chainsaw and unplug the power. Clean the unit before storing. Be extra careful
and make sure the air intake is free from dirt. Use a mild detergent and sponge to clean the
plastic parts. Store in a dry place out of reach of children. Make sure the chain is clean when
storing in a longer period of time and keep the chain saw guide bar chain oiled.
Warning!
Maintain safety.
Dangerous accidents may occur when:
Improper maintenance or removal of safety devices.
Always follow the instructions carefully
Always test the chain saw before performing any operation, check that the chain saw stops as
soon as you release the throttle handle. Do not use chain saw if this does not occur. The chain
saw must not be used until the fault is corrected.
Table of contents
Varning!
Använd aldrig ett redskap eller produkt med defekta säkerhetsdetaljer.
SAFETY MEASURES BEFORE OPERATING
Read the safety information and instruction manual carefully. Be sure you understand
the safety measures, instruction manual and warning labels. Use common sense when
operating the machine and use appropriate personal protective equipment.
Always check the performance and the machine combination that are used. It’s highly
important these matches in a satisfactory manner. This is to ensure the product or the
function and most important yours and others safety.
Do visual inspection of equipment or product before use. Fix or replace damaged or
worn parts immediately to reduce the risk of injury. Lubricate moving parts and check
that all screw-nuts and bolts are tightened.
Learn and remember the correct working methods. Beginners should keep a low speed
until the person has learn the proper use of the machine/product. The user/customer is
responsible to handle the situation correctly. Do not use the machine if it is experienced
to be dangerous for the user.
• The machine comes with ve-pole connection glove CEE 16A (3-phase + Neutral +
ground). The glove must be connected to a corresponding socket, which must be
installed by a qualied electrician. NOTE! In order for the machine to work, connect it
to a neutral-conductor outlet!
• The combined machine is tested before delivery and delivered lled with hydraulic oil
SHS 32, motor guard and connection glove are installed.
• The electrical chainsaw must be connected to a separate socket (230 V). Ensure that
the power socket is grounded.
• Place the machine on a level and stable surface. Make sure that it can not tip-over
• Fold down the collector table.
• Familiarize yourself with the machine without starting it.
• Test the safety switch: Start the machine, open the lock and lift the cover over the
splitting zone, the machine will shut down automatically as soon as the safety mecha-
nism located behind the machine is disabled. Do not use this machine if this does not
occur. The machine must not be used until the fault is corrected.
Table of contents
OPERATING THE MACHINE
Only people who understand the safety information and instructions in this manual may op-
erate the equipment. Be alert and careful when working with the machine and only use the
tool or product in the manner described in this manual. When working with equipment that
has moving parts, there is always the risk of injury. Be careful when working with equipment
equipped with hydraulic hoses ,oil under pressure can penetrate the skin. Seek medical at-
tention immediately if this occurs. Always work alone with the tools that are dened as single
purpose tools. Respect the equipment’s danger zone.
• Place the machine on stable at surface.
• Plug the power cord into a grounded 400V and chainsaw on 230V outlet. Always check
that the power cables and electrical connectors are not damaged before use.
• Check that the engine / hydraulic pump is running in the right direction. Rotation is
changed easily with phase inverter that is mounted on the machine.
• Press the engine start button, then the machine is ready to use.
• Always test the shut-o button before each use. Start the machine and press the “OFF”
button, the machine should turn o immediately, do not use the machine if this does not
occur. The machine must not be used until the fault is corrected.
• After nishing the work, switch OFF the power and unplug.
• Switch OFF the power and unplug the machine when you leave even if it’s only for a brief
moment. This ensures that no one in particular children can access and maneuver the
machine accidentally while playing.
PHASE INVERTER
After starting the log spliter, check the engine rotation. An arrow that indicates the direction
of rotation is located at the rear of the motor. If the ram does not move forward, this is a sign
that the engine is running in the wrong direction. Stop at once, check and change the engine’s
rotation.
The direction of the motor rotation is changed simply by turning the phase inverter with a
screwdriver.
ON/OFF
SWITCH
ROTATABLE PHASE INVERTER WITH A
SLOT FOR A SCREWDRIVER.
THE EMERGENCY BUTTON SHOULD
BE MOUNTED ON TOP OF THE
ON/OFF SWITCH
CONNETION GLOVE
Table of contents
CUTTING AND SPLITTING OF WOOD
• Make sure no one has hands or arms near moving parts of the machine
• Walk around and look at the machine to familiarize yourself with its features before start-
ing.
• Press the start button and wait a few minutes until the oil has reached the operating tem-
perature. Run the machine without any load for a number of times and check all functions
(cutting and splitting of wood) before work begins to get used to the controls.
• Lay a straight, twig-free timber on the feeding table and aim it against the electric saw.
• Set the length stop to the desired length.
• Start cutting by moving the log forward towards the longitudinal stop.
• Start the electric chainsaw and bring it down to the log. When you release the control
handle, the chain saw should stop.
• Grasp the lever and start splitting by moving it forward. The pressure plate pushes the log
against the splitting wedge. WARNING! Be careful when splitting hard or twisted wood.
Certain types of wood may crack or y away, which may result in injuries. The pressure
plate returns to the initial position when the splitting is complete.
• If the wood is stuck in the splitting knife: Return the pressure plate to the starting po-
sition, open the protective cover and remove the jammed wood. Warning for crushing
injuries! Make sure the pressure plate is in its starting position and had stopped moving
before performing anything on the machine. NEVER put your hand or other body part
between the pressure plate and the splitting knife, use suitable tools such as spike or rub-
ber mallet to loosen the jammed wood, never use your hands!
Length - guide
Loosen the bolt and move
to tube to desired measure-
ments.
Open the guard by loosening the lock
Table of contents
TRANSPORT AND STORING
Make sure there are no people, children and foreign objects around the area before transport-
ing the machine. Always take an extra caution during the transport. Ensure that the product
is well secured and that transport brackets are mounted. Always place the load as low as pos-
sible. Respect the danger zone even during transport. When lifting the equipment, never go
underneath suspended loads. Trailer used for transport should have working brakes. Always
store the machine in a dry place preferably underneath a cover when not in use. Ensure that
the product is stable and not likely to tip over. Never let children play where the machine is
being stored. Always keep in mind the risk of tipping!
Kellfri disclaim any responsibility for self-made modications, alterations or conversions of the product.
ALWAYS REMEMBER!
• Work alone, concentrate and always use common sense.
• Use working gloves, safety glasses and shoes with steel cap.
• Do not wear loose or hanging clothing that can be drawn into the machine.
• Always connect the hydraulic pressure hoses correctly.
MAINTENANCE AND SERVICE
Ensure that the unit is stable and cannot tip over during maintenance and service. Replace
damaged or worn parts immediately to reduce the risk of abrasion. Always perform mainte-
nance, service and inspection, as recommended. Use only original replacement parts or spare
parts with equivalent performance to reduce the risk of damage. All repairs and connections
with electricity must be performed by a qualied person.
Check all nuts and bolts are tightened after performing maintenance and service.
Always test the machine before using it.
Adjust the valve package to make the manoeuvering of the splitter easier.
Adjust by
moving the
valve package
Table of contents
RECYCLING
This product must not be disposed of as household waste.When scrapping, the
machine must be disassembled and transported to the municipality’s intended
location. Contact your municipality for further information.
SERVICE INTERVAL ACTION
Oil Exchange after 10 h
Thereafter every 50 h
or once a year
Oil Change
• Use hydraulic oil ISO 32 or 46
• Draining the tank is done by removing the
drain-plug under the tank.
• Fill through the ller plug on top.
Bolts and nuts Check regularly, preferably before
each use
Check and retighten all bolts and nuts
Moving parts Regularly Lubricate moving parts on a regular basis
Chainsaw Regularly Check the condition of the following parts:
Gear: check for abrasion and/or cracks
Guide bar: Check for abrasion.
Chain: The cutting links must be kept sharp for the
machine to cut eciently. Sharpens if requires.
TROUBLESHOOTING
ERROR PROBABLE CAUSE ACTION
The piston is not moving
forward
Low or no pressure in the system
The engine rotates the wrong
way
Check oil pressure and level. check if there’s a leak age
in the system.
Check the engine rotation and reverse if requires
The machine doesn’t start Fault with the power source
The machine is not correctly
plugged
Check the power source
Check and plug the machine correctly.
The machine don’t have
the power
Low or no pressure in the system Check if there’s leakage in the system.
Check all couplings and hydralic hoses.
Chainsaw is not working The machine is not plug
the Neutral conductor is not
connected
Check and connect.
Contact a qualied electrician for repair
All repairs and connections with electricity must be
carried out by a qualied person!
Table of contents
13KW340 SPAREPARTS
NO. SPECIFICATION
1. Guide roller, nylon 80/16 x95mm
2. Supporting arm
3. Cylinder 60/37 stroke 630
4. Pin 35 x95mm
5. Pin 16 x100mm - drawbar
6. Ball coupling 50 mm
7. Drawbar 50x50 x950mm
8. Outrigger 50x50 x400mm
9 Bolt FZB M12x25
10 Oil tank
NO. SPECIFICATION
11 Lid for rell and venting
12 Adapter-motor pump
13 Electric motor Y2 112M-4-4kW S1 1430 rpm 380V
14 Hub cap
15 Wheel 600-9 6 bearings
16 Tension spring with hook Ø30 rows. Ø4x150mm
17 Protective cover
18 Ball bearing 6304 2RS
19 Valve kit
20 Protective Cover
5
6
7
8
9
13
15
14
12
11
10
16
17
18
19
20
2
1
3
4
Table of contents
POS.NO. SPECIFICATION
21. Hydraulic valve
22. Valve house 90º
23. Hydraulic tube ½L=370mm- 90º
90º coupling : RETURN pump-tank
24. Hydraulic tube ½ L=1050 mm
90ºcoupling: Pressure,cylinder- control valve
25. Hydraulic pump
26. Hydraulic tube ½ L=1000 mm
27. Hydrualic tube ½ L=450 mm
28. Hydraulic tube ½L=350 straight
90º coupling
21 22
23
24
25
27
28
Table of contents
SPARE PARTS PRODUCT.NO.
1. Ball coupling R13-KW340.005
2. Wheel, 600 - 9 6 PR R13-KW340.013
3. Adjuster arm for the knife R13-KW340.033
4. Electrical chainsaw R13-KW340.027
5. Guide roller, nylon R13-KW340.001
6. Attachment for guide rollers R13-KW340.002
7. Motor guard R13-KW340.029
8. Guard cover R13-KW340.013
9. Electic motor 4 kW (not shown in the pict.) R13-KW340.011
10. Hydraulic pump R13-KW340.028
SPARE PART CHAINSAW
R13-KW109.001 Chain 16"
R13-KW109.002 Sword 16"
3
2
7
8
1
5
6
4
Table of contents
INSTALLATION INSTRUCTIONS
The chainsaw is delivered separately (not tted to the machine)
A mounting plate and bracket that locks the chainsaw holder in place is delivered together
with the chainsaw.
Make sure that the bracket is mounted on the chain
saw, (marked in the picture) if the bracket is not
mounted see the instruction below:
Install the bracket on the chainsaw
1. Disassemble the cover (marked on the picture)
2. Disassemble the chain and the sword
3. Install the bracket as shown in the picture above, tighten all screws
4. Re-t the sword and chain, check and tighten the chain.
1. 2. 3.
Table of contents
