Kenmore 110.84422610 User manual

Use & Care Guide
Manual de uso y cuidado
Guide d’utilisation et d’entretien
English / Español / Français
Table of Contents...2 / Índice...17 / Table des matières...34
Kenmore®
120-Volt Electric Compact Dryer
Secadora compacta électrica de 120 voltios
Sécheuse électrique compacte 120 volts
Model/Modelo/Modèle: 110.84422610
P/N W10832415B
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2C3
www.sears.ca

2
DRYER SAFETY
DRYER SAFETY...........................................................................2
INSTALLATION INSTRUCTIONS.............................................3
USING YOUR DRYER..............................................................10
DRYER CARE.............................................................................12
TROUBLESHOOTING.............................................................. 13
PROTECTION AGREEMENTS............................................... 16
WARRANTY..............................................................................16
ASSISTANCE OR SERVICE.................................... Back Cover
TABLE OF CONTENTS

3
Remove Shipping Material
Before you install your dryer, remove all shipping material.
To avoid damaging the oor, use the top of the carton to slide the
dryer into place.
Stand the dryer up.
Remove the tape from the dryer door. Open the dryer door and
remove the parts bag from the dryer drum. Close the door.
INSTALLATION INSTRUCTIONS

4
Tools and Parts
Tools needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed here.
Flat-blade screwdriver Tin snips (new vent installations)
Level Vent clamps
Adjustable wrench that
opens to 1" (25 mm) or
hex head socket wrench
Caulking gun and
compound (for installing
new exhaust vent)
Parts supplied
Remove parts package from the dryer drum. Check that all parts
listed are included.
Cycle control knob Start button
Casters (4) Cord brackets (2) and
screws (2)
Parts needed
Check local codes, existing electrical supply and venting,
and see “Venting Requirements” and “Electrical Requirements”
before purchasing parts.
■Mobile home installations require metal exhaust system
hardware.
For information on ordering, please refer to the back cover. You
may also contact the dealer from whom you purchased your dryer.
Location Requirements
You will need
■A location that allows for proper exhaust installation.
See “Venting Requirements.”
■A 120-volt, 60 Hz, AC-only, 15- or 20-amp circuit.
■A grounded electrical outlet located within 2 ft (610 mm)
of either side of the dryer. See “Electrical Requirements.”
■A sturdy oor to support the dryer weight (dryer and load)
of 115 lbs (52 kg). The combined weight of a companion
appliance should also be considered.
■A level oor with a maximum slope of 1" (25 mm) under
entire dryer.
Do not operate your dryer at temperatures below 45°F (7°C).
At lower temperatures, the dryer might not shut o at the end
of an automatic cycle. Drying times can be extended.
The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
Installation Clearances
The location must be large enough to allow the dryer door
to open fully.
Dryer Dimensions Front View
237/8"
(606 mm)
13/4"
(44 mm)
*203/4"
(527 mm)
31"
(787 mm)
* Most installations require a minimum 5½" (140 mm) clearance
behind the dryer for the exhaust vent with elbows. See “Venting
Requirements.”

5
Side View
13/4"
(44 mm)
36"
(914 mm) 203/4"
(527 mm)
Back View
13/4"
(44 mm)
31/4"
(83 mm)
31/2"
(89 mm)
117/8"
(303 mm)
291/4"
(743 mm)
Minimum spacing for recessed area
and closet installation
The following dimensions shown are for the minimum spacing
allowed when the dryer is to be operated with, or without, the
Stack Stand Kit. To purchase a Stack Stand Kit, see the back cover.
■Additional spacing should be considered for ease of installation
and servicing.
■Additional clearances might be required for wall, door, and
oor moldings.
■For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings
are acceptable.
■Companion appliance spacing should also be considered.
Recessed or closet installation – Dryer only
18"
(457 mm)
51/2"*
(140 mm)
14" max.
(356 mm)
3"
(76 mm)
3"
(76 mm)
24 in.2
(155 cm2)
48 in.2
(310 cm2)
1"
(25 mm)
1"
(25 mm)
Recessed or closet installation – Stacked
3"
(76 mm)
3"
(76 mm)
24 in.2
(155 cm2)
48 in.2
(310 cm2)
1"
(25 mm)
1"
(25 mm)
12"
(305 mm)
12"
(305 mm)
51/2"*
(140 mm)
3"
(76 mm)
* Most installations require a minimum 5½" (140 mm) clearance
behind the dryer for the exhaust vent with elbows. See “Venting
Requirements.”
Mobile Home – Additional Location Requirements
This dryer is suitable for mobile home installations. The installation
must conform to the Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard
for Mobile Home Construction and Safety, Title 245, HUD Part
280) or Standard CAN/CSA-Z240 MH.
Mobile home installations require:
■Metal exhaust system hardware, which is available for
purchase from your dealer.
■Special provisions must be made in mobile homes to introduce
outside air into the dryer. The opening (such as a nearby
window) should be at least twice as large as the dryer
exhaust opening.
Closet door with vents
Recessed area
Closet door with vents
Recessed area
DRYER
WASHER

6
Electrical Requirements
■120-volt, 60 Hz, AC-only, 15- or 20-amp fused electrical supply
is required.
■A time-delay fuse or circuit breaker is recommended.
Check that the fuse or circuit breaker matches the rating
of your line.
■It is also recommended that a separate circuit serving only this
dryer be provided.
■Do not use an extension cord.
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■ For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with
the dryer: if it will not t the outlet, have a proper outlet
installed by a qualied electrician.
Venting
Venting Requirements
WARNING: To reduce the risk of re, this dryer MUST BE
EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
Dryer exhaust must not be connected into any gas vent, chimney,
wall, ceiling, attic, crawlspace, or a concealed space of a building.
Only rigid or exible metal vent should be used for exhausting.
4"
(102 mm)
4" (102 mm) heavy metal exhaust vent
■Only a 4" (102 mm) heavy metal exhaust vent and clamps
may be used.
■Do not use plastic or metal foil vent.
Rigid metal vent:
■Recommended for best drying performance and to avoid
crushing and kinking.
Flexible metal vent: (Acceptable only if accessible to clean)
■Must be fully extended and supported in nal dryer location.
■Remove excess to avoid sagging and kinking that may result
in reduced airow and poor performance.
■Do not install in enclosed walls, ceilings, or oors.
■The total length should not exceed 7¾ ft (2.4 m).
NOTE: If using an existing vent system, clean lint from entire length
of the system and make sure exhaust hood is not plugged with
lint. Replace plastic or metal foil vents with rigid metal or exible
metal vents. Review “Vent System Chart” and, if necessary, modify
existing vent system to achieve best drying performance.

7
Exhaust hoods:
■Must be at least 12" (305 mm) from ground or any object
that may obstruct exhaust (such as owers, rocks, bushes,
or snow).
Recommended Style:
Louvered hood Box hood
Acceptable Style:
Angled hood
Elbows
45° elbows provide better airow than 90° elbows.
Good Better
Clamps
■Use clamps to seal all joints.
■Exhaust vent must not be connected or secured with screws or
other fastening devices that extend into the interior of the duct,
because they can catch lint. Do not use duct tape.
Plan Vent System
Choose your exhaust installation type
Recommended exhaust installations:
Typical installations vent the dryer from the rear of the dryer.
Other installations are possible.
A
B
C
A. Exhaust hood
B. Flexible metal or rigid metal vent
C. Elbow
Alternate installations for close clearances:
Venting systems come in many varieties. Select the type best
for your installation. Two close-clearance installations are shown.
Refer to the manufacturer’s instructions.
A B
A. Over-the-top installation
(also available with one offset elbow)
B. Periscope installation
NOTE: The following kits for close clearance alternate installations
are available for purchase. For information on ordering, see the
back cover.
■Over-the-Top Installation:
Part Number 4396028
■Periscope Installation (for use when there is a mismatch
between the size of the dryer vent and wall vent openings):
Part Number 4396037 – for mismatch of 0" (0 mm)
to 18" (457 mm)
Part Number 4396011 – for mismatch of 18" (457 mm)
to 29" (737 mm)
Part Number 4396014 – for mismatch of 29" (737 mm)
to 50" (1.27 m)

8
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
Determine vent path
■Select the route that will provide the straightest and most
direct path outdoors.
■Plan the installation to use the fewest number of elbows
and turns.
■When using elbows or making turns, allow as much room
as possible.
■Bend vent gradually to avoid kinking.
■Use the fewest 90° turns possible.
Determine vent length and elbows needed for best drying
performance
■Use the “Vent System Chart” below to determine type of vent
material and hood combinations acceptable to use.
NOTE: Do not use vent runs longer than those specied in
the “Vent System Chart.” Exhaust systems longer than those
specied will:
■Shorten the life of the dryer.
■Reduce performance, resulting in longer drying times and
increased energy usage.
The “Vent System Chart” provides venting requirements that will
help to achieve the best drying performance.
Vent System Chart
Number of
90° turns
or elbows
Type of vent Box or
louvered
hoods
Angled hoods
0Rigid metal 36 ft (11 m) 26 ft (7.9 m)
1Rigid metal 26 ft (7.9 m) 16 ft (4.9 m)
2Rigid metal 16 ft (4.9 m) 6 ft (1.8 m)
Install Vent System
1. Before installing the vent system, be sure to remove the wire
exhaust guard that is located at the exhaust outlet.
2. Install exhaust hood.
12" min.
(305 mm)
12" min.
(305 mm)
Install exhaust hood and use caulking compound to seal
exterior wall opening around exhaust hood.
3. Connect vent to exhaust hood.
Vent must t inside exhaust hood. Secure vent to exhaust hood
with 4" (102 mm) clamp. Run vent to dryer location. Use the
straightest path possible. See “Determine vent path” in “Plan
Vent System.” Avoid 90° turns. Use clamps to seal all joints.
Do not use duct tape, screws, or other fastening devices that
extend into the interior of the vent to secure vent, because they
can catch lint.
Install Cord Bracket and Casters
Do not move dryer into its nal location until the following steps
have been performed.
Install cord bracket
1. Remove tape from the power cord and the rear panel.
2. Insert cord brackets into slotted holes in rear panel and
secure with screws provided.
B
A
C
A. Cord bracket
B. Slotted hole
C. Screw
NOTE: Power supply cord may be wrapped around the brackets
for storage convenience when dryer is not in use.

9
Install casters
1. To avoid damaging oor, use a large at piece of cardboard
from dryer carton. Place cardboard under entire back edge
of the dryer.
2. Firmly grasp dryer body and gently lay dryer on its side
on cardboard.
3. Screw casters into dryer base at four corners and
tighten securely.
4. Set the dryer upright. In doing so, be certain that the dryer
does not roll away from you.
Connect Vent
1. Connect vent to exhaust outlet.
Using a 4" (102 mm) clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure the vent is
clean. Dryer vent must t over dryer exhaust outlet and inside
exhaust hood. Check that vent is secured to exhaust hood with
a 4" (102 mm) clamp.
2. Roll dryer into its nal location. Avoid crushing or kinking
the vent.
Complete Installation
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see what was skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Check dryer’s nal location. Be sure vent is not crushed
or kinked.
5. Check that dryer is on a level surface.
6. Plug into a grounded 3 prong outlet.
7. Remove lm on the console and any tape remaining on dryer.
8. Remove tape from lint screen (located on inside back wall
of dryer).
9. Read “Using Your Dryer.”
10. Wipe dryer drum interior thoroughly with a damp cloth to
remove any dust.
11. To test the dryer, set the dryer on a full heat cycle (not an air
cycle) for 20 minutes and start the dryer.
If the dryer will not start, check the following:
■Controls are set in a running or ON position.
■Push to Start button has been rmly pressed.
■Dryer is plugged into a grounded 3 prong outlet.
■Household fuse is intact and tight, or circuit breaker has
not tripped.
■Dryer door is closed.
12. When the dryer has been running for 5 minutes, open the dryer
door and feel for heat. If you feel heat, cancel cycle and close
the door.
If you do not feel heat, check the following:
■Controls are set on a heated cycle, not an air cycle.
NOTE: You may notice an odor when dryer is rst heated. This
odor is common when the heating element is rst used. The odor
will go away.

10
WARNING: To reduce the risk of re, electric shock, or injury
to persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
Before using your dryer, wipe the dryer drum with a damp cloth
to remove dust from storing and shipping.
1. Clean the lint screen before each load. See “Cleaning the Lint
Screen.”
2. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
3. Turn the Cycle Control knob to the recommended cycle
for the type of load being dried. See “Drying, Cycle, and
Temperature Tips.”
4. Press PUSH TO START.
Stopping and Restarting
You can stop your dryer anytime during a cycle.
To stop your dryer
Open dryer door or turn Cycle Control knob to OFF.
NOTE: The Cycle Control knob should point to an O area when
dryer is not in use.
To restart your dryer
1. Close the door.
2. Select a new cycle and temperature (if desired).
3. Press Push to Start button.
USING YOUR DRYER
Starting Your Dryer