Kenmore 240-volt compact electric dryers Original instructions

Owner's Manual and
Installation Instructions
240-Volt
COMPACT
ELECTRIC DRYERS
IMPORTANT:
Read and follow all safety
and operating instructions
before first use of this product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
PARTNO. 3406896 PRINTED iN U.S.A.

BEFORE USING YOUR NEW DRYER 2
SEARS COMPACT ELECTRIC DRYER WARRANTY 3
IMPORTANT SAFETY INSTRUCTIONS 4
INSTALLATION INSTRUCTIONS
OPERATING YOUR DRYER 26
LAUNDRY TIPS 31
CARING FOR YOUR DRYER 33
TROUBLESHOOTING 36
SEARS MAINTENANCE AGREEMENT 38
Please read this manual, It will help you
install and operate your new Kenmore
compact dryer in the safest and most
economical way.
For more information about the care
and operation of Kenmore appliances
call your nearest Sears store, You will
need the complete model and serial
numbers when requesting information,
Your dryer's model and serial numbers
are located on the Model and Serial
Number Plate.
Use the space below to record the
model number and serial number of
your new Kenmore compact dryer.
Model No.
Serial No.
Date of Purchase
Keep this book and your Sears
Salescheck (receipt) in asafe place
for future reference,

OneYearWarrantyon
MechanicalandElectricalParts
For one year from the date of purchase,
if this dryer is installed and operated
according to the instructions in this
manual, Sears will repair or replace
any of its mechanical or electrical
parts if they are defective in material
or workmanship.
NOTE: Exhausting your dryer with
plastic product may void this warranty.
Pages 21-24 of this manual describe
the complete exhaust requirements
for this dryer.
Warranty Service
Warranty service is available by
contacting your nearest Sears
Service Center in the United States.
This warranty applies only while this
dryer is used in the United States.
This warranty gives you specific legal
rights, and you may also have other
rights which vary from state to state.
Sears, Roebuck and Co., Dept.
817WA, Hoffman Estates, IL 60179.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual
and on your appliance, Always read and obey all safety messages,
This is the safety alert symbol, This symbol alerts
you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety
alert symbol and the word "DANGER" or "WARNING,"
These words mean:
You will be killed or seriously
injured if you don't follow
instructions,
You can be killed or seriously
injured if you don't follow
instructions.
All safety messages will identify the hazard, tell you how to reduce the
chance of injury, and tell you what can happen if the instructions are
not followed.
3

YOUR SAFETY IS IMPORTANT TO US.
WARNING: To reduce the risk of fire,
electric shock, or injury to persons when
using your dryer, follow basic precautions,
including the following:
•Read all instructions before using
the dryer.
• Do not dry articles that have been
previously cleaned in, washed in, soaked
in, or spotted with gasoline, dry-cleaning
solvents, other flammable or explosive
substances as they give off vapors that
could ignite or explode.
• Do not allow children to play on or in
the dryer. Close supervision of children
is necessary when the dryer is used
near children.
• Before the dryer is removed from service
or discarded, remove the door to the
drying compartment.
• Do not reach into the dryer if the drum
is moving.
• Do not install or store this dryer where
it will be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the
dryer or attempt any servicing unless
specifically recommended in the Owner's
Manual or in published user-repair
instructions that you understand and
have the skills to carry out.
• Do nat use fabric softeners or products
to eliminate static unless recommended
by the manufacturer of the fabric softener
or product.
• Do nat use heat to dry articles containing
foam rubber or similariy textured rubber-
like materials.
• Clean Iint screen before or after each
load,
• Keep area around the exhaust opening
and adjacent surrounding areas free from
the accumulation of tint, dust, and dirt.
• The interior of the machine and exhaust
duct should be cleaned periodically by
qualified service personnel.
SAVE THESE INSTRUCTIONS
IIMPORTANT: Observe all governing codes and ordinances. I
4

INSTALLATION OVERVIEW
For a complete list of tools and parts
needed, see pages 5-7.
A, SELECT LOCATION
FOR YOUR DRYER (pgs. 8-10)
Standard Installation (p. 8) Recessed Area/Closet Installation
Instructions (p. 9)
B, INSTALL LEVELING LEGS (p, 11)
Tools Needed: PaNs Needed:
Jstable
wrench Two corner posts
(from dryer carton)
Flashlight (optional
depending on installation)
4 leveling legs (supplied with dryer)

C, MAKE ELECTRICAL CONNECTION (pgs, 12-20)
Hold-downscrew
Terminalblockcover
If using a power cord:
Tools Needed: Parts Needed:
V4-1nch nut #2 Phillips head
driver (shown) screwdriver
or socket wrench
Flashlight {optional
depending on installation)
New 3- or 4-wire, 30-amp.
U.L.-listed power supply
cord kit (includes strain relief)
If making a direct wire connection:
V4-1nch nut #2 Phillips head
driver (shown) screwdriver
or socket wrench
Wire stripper Flashlight (optional
depending on installation)
10-gauge, 3- or 4-wire, 314':U.h-listed,
flexible armored strain relief
or non-metallic
sheathed copper cable
(with grounding wire)

D, INSTALL KNOBS (p. 20)
PUSH TO START
PaNs Needed:
3 knobs(supplied with d_er)
FABRIC/TEMPERATURE @
CYCLE
SELECTOR
E, CONNECT EXHAUST (pgs, 21-24)
i •
Tools Needed:
Tin snips
Flashlight {optional
depending on installation)
Duct tape
Flat-bladed
screwdriver
PaNs Needed:
4-Inch rigid or
flexible heavy
metal vent
4-Inch metal elbow(s)
(optional depending
on installation)
4-Inch outlet (4) 4-Inch
exhaust hood diameter damps 7

A. SELECT LOCATION
FOR YOUR DRYER
Selecting the proper location for your
dryer makes installation easier and
gives you the best drying performance,
STANDARD INSTALLATION
Check location where dryer will be installed.
Proper installation is your responsibility.
Make sure you have everything necessary
for correct installation including proper
floor support, a level floor, and a separate
3g-amp. fuse.
• Protect dryer from the weather. Proper
operation of dryer cycles requires
temperatures above 45°F, At lower
temperatures, the dryer may not shut
off at the end of automatic cycles, and
drying times will be extended.
Explosion Hazard
Keep flammable materials and vapors,
such as gasoline, away from dryer.
Place dryer at least 18 inches above
the floor for a garage installation.
Failure to follow these instructions
can result in death, explosion, or fire.
•Check code requirements. Some
codes limit or do not permit installation
of clothes dryers in garages, closets,
mobile homes, or sleeping quarters.
Contact your local building inspector.
J
_- _ Separate
\ 30.ompf_
OroonOe0recep,ac,e:
' '_ /Withinf2_;ee'°f either
Support: Floor must be Level floor: Maximum
sturdy enough to support allowable slope under entire
a total weight of110 dryer - 3/_inch.
pounds (includes dryer
and lead weight).

RECESSED AREA/CLOSET
INSTALLATION INSTRUCTIONS PRODUCT DIMENSIONS
Check governing codes and ordinances. Location must be large enough to fully
This dryer may be installed in arecessed open dryer door.
area or closet.
Confined or Recessed Area Installation
The dryer must be exhausted outdoors,
The moisture and lint indoors may cause:
• Lint to gather inside and around the
dryer and be fuel for afire.
• Moisture damage to woodwork, furniture,
paint, wallpaper, carpet, etc.
• Housecleaning problems and possible
health problems.
Closet Installation
WARNING: To reduce the risk of fire, this
appliance must be exhausted outdoors
when installed in a closet.
NOTE: No fuel burning appliances may
be installed in the same closet as a dryer.
201/2"
18"
"1"4
olo
FrontView
(DoorNotShown)
**48 sq.in.,
minimum_
-- ventilation
area
_" **24 sq.in.,
"--- minimum_
ventilatien
area
t,, SideView
(DoorShown)
E}
FrontView
(Door WithVent)
MINIMUMINSTALLATIONSPACING,ClosetInstallationMUSTbeexhaustedoutside.
* Additionalclearancesforwall, doorandfloormoldingsmaybe required.
** Openingis minimumfor closetdoor.Louvereddoorwithequivalentair openings
isacceptable,
** *Additionalspaceisneededwhenexternalexhaustelbowisused.
3_
3"
• The installation spacing is in inches
and is the minimum allowable.
• Additional spacing should be
considered for ease of installation
and servicing.
• If closet door is installed, the
minimum air openings in top and
bottom are required. Louvered doors
with equivalent air openings in top
and bottom are acceptable.
9

STAND KIT CLEARANCES
12,,E-Iiiiiiii
*'1"÷ FrontView Side View
StackStand StackStand
(Door Dot Shown) (Door Shown)
3"
3"
FrontView
(DoorWithVent)
* 1"dimensionmustbefromfrontoftimerknoh.
** Additionalclearancesforwall, doorandDoormoldingsmayberequired.
*** Openingis minimumforclosetdoor.Louvereddoorwithequivalentair openings
isacceptable.
• The installation spacing is in inches • For complete installation information,
and is the minimum allowable, order Stand Kit Installation Instructions,
Part No, 49971/8, from your Sears
store or Sears Service Center.
MOBILE HOME EXHAUST
REQUIREMENTS
• The dryer must not be installed where
it will be exposed to water and/or
weather. Proper operation of dryer cycles
requires temperatures above 45°F.
At lower temperatures, the dryer may
not shut off at the end of automatic
cycles. Drying times will be extended.
This dryer is suitable for mobile home
installations. The installation must
conform to the Manufactured Home
Construction and Safety Standard,
Title 24 CFR, Part 3280 (formerly the
Federal Standard for Mobile Homes
Construction and Safety, Title 24,
HUD Part 280).
• Dryer exhaust vent must not be
connected or secured with screws
or other devices which extend into
the interior of the vent.
• If the dryer is exhausted outdoors,
the exhaust vent must be securely
fastened to a non-combustible
portion of the mobile home
structure and must _
not terminate
beneath the
mobile home.
• While in transit,
the dryer must
be securely [,_
fastened to
the floor. Order
Mobile Home Installation
Kit 346764 from your Sears
store or Sears Service Center,
Kit includes the necessary fastening
hardware and detailed installation
instructions.
10

B. INSTALL LEVELING LEGS
Leveling your dryer correctly will
reduce operating noise and provide
improved drying performance.
STEP 1. Take two of the cardboard
corners from the carton. Place them
on the floor in back of the dryer.
STEP 2. Firmly grasp the body of the
dryer. Gently lay dryer on the cardboard
corners.
STEP 4. Now stand the dryer up
and move it close to its final location.
Leave enough room to connect the
exhaust vent.
STEP 5. Check levelness of dryer by
placing a level on top of the dryer, first
side4o-side; then front4o-back.
STEP 3. Start to screw the legs into the
holes by hand. Use a wrench to finish
turning the legs. They should stick out
about 1 inch.
STEP 6. if dryer is not level, prop the
dryer up using two stacked cardboard
corner posts. Use a wrench to adjust
the legs up or down.
NOTE: it may be necessary to level
the dryer again after it is moved into
its final position.
11

C. MAKE ELECTRICAL
CONNECTION
It is your responsibility:
• To contact a qualified electrical installer.
• To assure that the electrical installation
is adequate and in conformance with
the National Electrical Code, ANSll
NFPA 70-latest edition and all local
codes and ordinances.
Copies of the code standards listed
above may be obtained from:
National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
ELECTRICAL REQUIREMENTS
The proper electrical connection
ensures asafe installation that
meets local code requirements.
A three-wire or four-wire, single phase
120/240-volt 60-Hz., AC-only, electrical
supply (or three-wire or four-wire,
120/208-volt if specified on serial/rating
plate) is required on a separate 30-ampere
circuit, fused on both sides of the line.
A time-delay fuse or circuit breaker is
recommended.
This dryer is manufactured with the 3-wire,
frame-grounding conductor connected
to the NEUTRAL (center) of the wiring
harness of the terminal block. Do not
have afuse in the neutral or grounding
circuit. A fuse in the neutral or grounding
circuit could result in an electrical shock.
Use a 4-conductor cord when the dryer
is installed in a mobile home or an
area where local codes do not permit
grounding through the neutral.
ELECTRICAL CONNECTION OPTIONS And You Will Be Go To
If Your Home Has: Connecting To: Page
3-wire electrical A U.L.-listed, 120/240-volt 13 -I.
receptacle minimum, 30-amp., dryer
(NEMA Type 10-30R) power supply cordt
3-wire direct A fused disconnect or 14 - II.
circuit breaker boxt
4-wire electrical A U.L.-listed, 120/240-volt 17- III.
receptacle minimum, 30-amp., dryer
(NEMA Type 14-30R) power supply cord.
4-wire direct A fused disconnect or 19- IV.
circuit breaker box.
*If local codes do not permit the connection of a frame-grounding conductor
to the neutral wire, see the instructions on page 16.
12

I. THREE-WIRE ELECTRICAL
CONNECTION TO RECEPTACLE
Use a 3-wire power supply cord:
Electrical Shock Hazard
Turn power supply off before
connecting cord.
Use a new 30-ampere power
supply cord.
Plug into a grounded outlet.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
Local codes may permit the use of
a U.L.-listed, 120/240-volt minimum,
30-ampere, dryer power supply cord
kit (pigtail). Power supply cord should
be type SRD or SRDT and be at least
four feet long. The wires that connect
to the dryer must end with ring terminals
or spade terminals with upturned ends.
Spadeterminals_.__ ,.j_
withupturnedends
Thisbladeconnected Ring
strainrelief (whiteorcenter)
Three-Wire Power Supply Cord
The power supply cord must have three,
No.-10 copper wires to match a three-
wire receptacle of NEMA Type 10-30R.
Do not use an extension cord with
this dryer.
Do not connect plug end of power
supply cord into a live receptacle
before connecting power supply cord
to dryer terminal block,
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or break-
down, grounding will reduce the risk of
electric shock by providing a path of
least resistance for electric current. The
power supply cord must be plugged into
an appropriate outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
WARNING: Improper connection of
the equipment-grounding conductor can
result in a risk of electric shock, Check
with a qualified electrician or serviceman
if your are in doubt as to whether the
appliance is properly grounded.
Do not modify the plug on the power
supply cord. If it will not fit the outlet,
have a proper outlet installed by a
qualified electrician.
STEP 1. Turn power supply off.
STEP 2. Remove hold-down screw
and terminal block cover.
Terminalblockcover Hold-downscrew
\ /
Three-wire
receptacle
(NEMAType
10-30R)
13

STEP 3. Attach a 3/4-inch, U.L.qisted,
strain relief to the hole below terminal
block opening, Strain relief should have
a tight fit with dryer cabinet and be in a
horizontal position. Put the power supply
cord through the strain relief.
STEP 4. Loosen or remove terminal block
screws. Connect the neutral wire (white
or center) of power supply cord under
the center screw of the terminal block.
STEP 5. Connect the other two wires
to outer terminal block screws. Tighten
all terminal block screws firmly.
Externalground
connector
Neutral
groundingwire
(green/yellow)
Centersilver-colored
terminalblockscrew
Neutral
wire
(white)
3II
/4, U.L.-listed,
strainrelief
3-Wire Connection with
Frame-Grounding Conductor
STEP 6. Tighten the strain relief screws.
STEP 7. Insert tab of terminal block
cover into slot of the dryer rear panel.
Secure cover with hold-down screw.
If local codes do not permit the
connection of a frame-grounding
conductor to the neutral wire, see
the instructions on page 16.
Otherwise, proceed with Knob
Installation. See "INSTALL KNOBS"
on page 20.
II. THREE-WIRE ELECTRICAL
CONNECTION (DIRECT WIRE)
Prepare cable as directed:
Electrical Shock Hazard
Turn power supply off before
connecting wires.
Use 10-gauge solid copper wire.
Electrically ground dryer.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
The dryer can be connected directly
to fused disconnect or circuit breaker
box with three-wire, flexible armored or
non-metallic sheathed copper cable
(with grounding wire). All current-carrying
wires must be insulated.
A conduit connector must be installed at
junction box. Allow four feet of slack in the
line so dryer can be moved if servicing
is ever necessary.
GROUNDING INSTRUCTIONS
This appliance must be connected to
a grounded metal, permanent wiring
system; or an equipment-grounding
conductor must be run with the circuit
conductors and connected to the
equipment_grounding terminal or
lead on the appliance.
STEP 1, Turn power supply off.
STEP la. Strip 3Vz inches of outer
covering from end of cable.
14

STEP lb. Cut 1 inch of insulation from
the end of each insulated wire. Shape
the end of each wire into a "U" shaped
hook.
STEP 2. Remove hold-down screw and
terminal block cover.
Terminalblockcover Hold-downscrew
\ /
STEP 3. Attach a 3/4-inch, U,L,-listed,
strain relief to the hole below terminal
block opening. Strain relief should have
a tight fit with dryer cabinet and be in a
horizontal position. Put the direct wire
cable through the strain relief.
Externalgroond
connector
STEP 4. Loosen or remove terminal block
screws. Connect the neutral wire (white
or center) of direct wire cable under the
center screw of the terminal block.
STEP 4a. Place the hook-shaped end
of the wire over the terminal
The open side of the hook should face
to the right. Squeeze hook end of wire
together to form a loop.
STEP 5. Connect the other two wires
to outer terminal block screws using the
same method(s) described in STEP 4a.
Tighten all terminal block screws firmly.
STEP 6. Tighten the strain relief screws.
STEP 7. Insert tab of terminal block
cover into slot of the dryer rear panel.
Secure cover with hold-down screw.
If local codes do not permit the
connection of a frame-grounding
conductor to the neutral wire, see
the instructions on page 16.
Otherwise, proceed with Knob
Installation. See "INSTALL KNOBS"
on page 20.
Centersilver-colored
terminal block screw
Neutral grounding
wire (green/yellow)
Neutral
"wire
(white)
_3/4'_ U.L.-listed,
strainrelief
3-Wire Connection with Direct Wire
and Frame-Grounding Conductor 15

ALTERNATE CONNECTION:
If local codes do not permit the
connection of a frame-grounding
conductor to the neutral wire:
STEP 1. Make sure the power supply to
the dryer is off.
STEP 2. Make sure the power supply
cord or direct wire cable is in place (see
steps 1-3 on pages 13-14 for power cord
connections or steps 1-3 on pages 14-15
for direct wire connection).
STEP 3. Remove the neutral grounding
wire (green/yellow wire) from external
grounding connector screw. Loosen or
remove terminal block screws. Connect
neutral grounding wire and the neutral
wire (white or center) of power supply
cord or direct wire cable under the center
screw of the terminal block.
STEP 4. Connect the other two wires
to outer terminal block screws. Tighten
all terminal block screws firmly.
STEP 5, Tighten the strain relief screws.
STEP 6. Insert tab of terminal block
cover into slot of the dryer rear panel.
Secure cover with hold-down screw.
STEP 7. Connect separate copper
grounding wire from external ground
connector to an adequate ground, If
codes permit and a separate grounding
wire is used, it is recommended that a
qualified electrician determine that the
grounding path is adequate.
Proceed with Knob Installation.
See "INSTALL KNOBS" on page 20.
External Neutral
ground grounding wire
connector (green/yellow)
Groundingpath
determined by a
qualified electrician
Alternate 3-Wire Connection with
External-Grounding Conductor
16

III. MAKE FOUR-WIRE ELECTRICAL
CONNECTION TO RECEPTACLE
Use a 4-wire power supply cord:
Electrical Shock Hazard
Turn power supply off before
connecting cord.
Use a new 30-ampere power
supply cord.
Plug into a grounded outlet.
Failure to follow these instructions
can result in death, fire, or
electrical shock.
Local codes may permit the use of
a U.L.-listed, 120/240-volt minimum,
30-ampere, dryer power supply cord
kit (pigtail). Power supply cord should
be type SRD or SRDT and be at least
four feet long. The wires that connect
to the dryer must end with ring terminals
or spade terminals with upturned ends.
NEUTRAL NEUTRAL
_/4",U.L.-listed, (white)
strainGrelie_
prong wire(green) terminals
Four-Wire Power Supply Cord
(Mobile homeor other four-wire installations)
For mobile homes or other four-wire
installations, the power supply cord must
have four, No.-10 copper wires and
match a four-wire receptacle of NEMA
Type 14-30R. The fourth wire (grounding
conductor) must be identified with a
green cover or bare copper wire and the
neutral conductor by a white cover.
Do not use an extension cord with
this dryer.
Do not connect plug end of power
supply cord into a live receptacle before
connecting power supply cord to dryer
terminal block.
GROUNDING INSTRUCTIONS
This appliance must be grounded.
in the event of malfunction or break-
down, grounding will reduce the risk
of electric shock by providing a path
of least resistance for electric current.
The power supply cord must be plugged
into an appropriate outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
WARNING: Improper connection of the
equipment-grounding conductor can
result in a risk of electric shock, Check
with aqualified electrician or serviceman
if your are in doubt as to whether the
appliance is properly grounded.
Do not modify the plug on the power
supply cord, If it will not fit the outlet,
have a proper outlet installed by a
qualified electrician.
STEP 1. Turn power supply off.
STEP 2. Remove hold-down screw
and terminal block cover.
Terminalblockcover Hold-downscrew
\ /
Four-wirereceptacle
(NEMAType14-30R)
17

STEP 3. Attach a 3/4-inch, U,L,-listed,
strain relief to the hole below terminal
block opening. Strain relief should have
a tight fit with dryer cabinet and be in a
horizontal position, Put the power supply
cord through the strain relief,
STEP 4. Remove the center terminal
block screw, Remove the neutral ground-
ing wire (green/yellow wire) from external
grounding screw.
Externalground
connector
,c
Center silver-colored
terminal block screw
©
STEP & Connect neutral grounding wire
and the neutral wire (white) of power
supply cord under the center screw of
terminal block.
STEP 6. Connect the other two insulated
wires to outer terminal block screws.
STEP 7. Connect the green, grounding
wire from the power supply cord to the
external grounding conductor screw.
Tighten all terminal block screws firmly.
STEP 8, Tighten the strain relief screws.
STEP 9. Insert tab of terminal block
cover into slot of the dryer rear panel.
Secure cover with hold-down screw.
Proceed with Knob Installation.
See "INSTALL KNOBS" on page 20.
Green/yellowwire
ofharness
Centersilver-
External colored terminal Neutral wire
ground block screw (white)
coeeeutor
18
Green wire Neutral
ofpowersupply groundingwire
cord or bare
copper wire
3/4_U.L-listed, strain
relief
4-Wire Connection with
Frame-Grounding Conductor

IV. FOUR-WIRE ELECTRICAL
CONNECTION (DIRECT WIRE)
Prepare cable as directed:
Electrical Shock Hazard
Turn power supply off before
connecting wires.
Use 10-gauge solid copper wire.
Electrically ground dryer.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
The dryer can be connected directly
to fused disconnect or circuit breaker
box with four-wire, flexible armored or
nommetallic sheathed copper cable
(with grounding wire), All current-carrying
wires must be insulated. The grounding
wire may be bare.
A conduit connector must be installed
at junction box. Allow four feet of slack
in the line so dryer can be moved if
servicing is ever necessary.
GROUNDING INSTRUCTIONS
This appliance must be connected to
a grounded metal, permanent wiring
system; or an equipment-grounding
conductor must be run with the circuit
conductors and connected to the
equipment-grounding terminal or lead
on the appliance.
STEP 1. Turn power supply off.
STEP la. Strip 5 inches of outer covering
from end of cable. Leave bare grounding
wire at 5 inches.
STEP lb. Cut l_/z inches from 3 remaining
insulated wires. Strip insulation back 1 inch.
Shape the end of each wire into a "U"
shaped hook.
STEP 2. Remove hold-down screw
and terminal block cover.
Terminalblockcover Hold-downscrew
STEP 3. Attach a 3/4-inch, U.L.qisted,
strain relief to the hole below terminal
block opening. Strain relief should have
a tight fit with dryer cabinet and be in
a horizontal position, Put the direct wire
cable through the strain relief.
STEP 4. Remove the center terminal
block screw, Remove the neutral ground*
ing wire (green/yellow wire) from external
grounding screw.
Externalground
connector Center silver-colored
terminal block screw
0
Green/yellowwire
ofharness 19

STEP & Connect neutral grounding wire
and the neutral wire (white or center) of
direct wire cable under the center screw
of terminal block.
Centersilver-colored
terminal block screw
Externalground
connector
/
Bare copperwire
Neutralwire(white)
L "
Neutral
groundingwire
(green/yellow)
3/4",&L-listed,
strainrelief
4-Wire Connection with Direct Wire
and Frame-Grounding Conductor
STEP 6. Place the hook-shaped end of
the wire over the terminal block screw,
The open side of the hook should face
to the right. Squeeze hook end of wire
together to form a loop.
STEP 7. Connect the other two wires
to outer terminal block screws. Use the
same method described in STEP 6.
STEP 8. Connect the direct wire cable
(bare) grounding wire to the external-
grounding conductor screw. Tighten all
terminal block screws firmly.
STEP 9. Tighten the strain relief screws.
STEP 10. Insert tab of terminal block
cover into slot of the dryer rear panel.
Secure cover with hold-down screw.
D. INSTALL KNOBS
One large and two small knobs are
supplied with the dryer.
On the back side of each knob is a "D"
shaped notch, The "D" shaped notch will
fit onto the "D" shaped peg on the dryer
console.
STEP 1. Firmly holding the large CYCLE
SELECTOR knob, align the "D" shaped
notch of the knob with the "D" shaped
CYCLE SELECTOR peg. Push knob
into place.
STEP 2. The small FABRIC TEMPERATURE
knob is identified by a temperature indicator
marking. Firmly holding the small FABRIC
TEMPERATURE knob, align the "D"
shaped notch of the knob with the "D"
shaped FABRIC TEMPERATURE peg.
Push knob into place.
STEP 3. Firmly holding the small PUSH
TO START knob, align the "D" shaped
notch of the knob with the "D" shaped
PUSH TO START peg. Push knob into
place.
PUSH FABRIC/
TOSTART TEMPERATURE @
CYCLE
SELECTOR
Proceed with Knob Installation.
2O