Kenmore 16025628 User manual

Side-by-Side Refrigerator--Technical Information
Due to a possibility of personal injury or property damage, always contact an authorized technician for
service or repair of this refrigerator.
I CAUT,ON I
All safety information must be followed as provided in Service Manual 16025628.
IWARNING I
To avoid risk of electricalshock that can cause death or severe personal injury,disconnect unitfrom power before
servicing unless testing is required. Discharge capacitors through a I0,000 ohm resistor before handling. Wires
removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.
No-Load Performance, Controls in Normal Position
Refrigerator Center
Compartment Freezer Compartment
Percent Run Time Average Food Average Food
Kw/24 hr _+0.4 _+10% Cycles/24 hr
_+25% Temperature _+3°F Temperature _+3°F
Ambient °F 70° 90° 110° 70° 90° 110° 70° 90° 110° 70° 90° 110 ° 70° 90° 110°
22 cuft 1.2 1.85 2.6 35 55 75 24 24 19 37 39 42 0 0 -2
23 cu ft 1.2 1.85 2.6 35 55 75 24 24 19 37 39 42 0 0 -2
26 cuft 1.2 1.85 2.6 35 55 75 24 24 19 37 39 42 0 0 -2
Suction
Evaporator Evaporator Suction Line Average Total Pressure Head Pressure
Outlet Inlet _+7°F Wattage _+10% _+2PSIG _+5 PSIG
-+3°F _+3°F
Ambient °F 70° 90° 70° 90° 70° 90° 70° 90° 70° 90° 70° 90°
22 cuft -15 -15 -16 -!6 72 98 132 138 6"(Vac.) 0 87 137
23 cu ft -19 -15 -20 -!6 72 98 132 138 6"(Vac.) 0 95 137
26 cuft -15 -15 -16 -!6 72 98 132 138 6"(Vac.) 0 87 137
Schematic
I
I I
December 2004 1 12893007

Component Specifications
IWARNING
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires
removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.
Component
Compressor run capacitor
Compressor
Electric damper control
Thermistor
Condenser motor
Evaporator fan motor
Overload/Relay
Thermostat (Defrost)
Evaporator heater
22 & 26 cu. ft
Evaporator heater
23 cu. ft
Control board
Auger Motor
Water Valve
Super CooI Fan
Light switch /Interlock
Solenoid (Ice Chute)
Specifications all parts
115VAC/60HZ unless noted
Volt ..................................................... 220 VAC
Capacitance ...................................... 15 __dd+ 10%
BTUH ................................................. 905 BTUH
Watt ................................................... 60 Hz /153 watts
Current Lock rotor .............................. 19.0 amps_+ 15%
Current Full load ................................ 1.26 amps_+ 15%
Resistance Run windings ................... 3.33 ohms_+ 15%
Resistance Start windings .................. 4.28 ohms_+ 15%
Maximum closing time 36 seconds
Temperature Rating 20°F- 110°F
RPM 1
Temperature Resistance
77°F .................................................... 10,000 ohms_+ 1.8%
36°F ................................................... 29,500 ohms_+ 1.0%
0°F ...................................................... 86,300 ohms_+ 1.8%
Rotation (facing end opposite shaft) Clockwise
RPM 1120 RPM
Watt .................................................... 3.4 watts _+15%@ 115VAC
Current ............................................... 0.085 amps_+ 15%@ 115VAC
Rotation (facing end opposite shaft) Clockwise
RPM .......................................... 2800 RPM
Watt ........................................... 6.0 -+15% watts@l!5 VAC
Note: Fan blade must be fully seated
on shaft to achieve proper airflow.
UIt. trip amps @ 158°F (70°C) ........... 2.67 amps-+ 15%
Close temperature ........................... 142°F +9°
Open temperature ............................ 284°F +9°
Short time trip (seconds) .................... 10 seconds _+5
Short time trip (amps @77°F (25°C).. 11 amps _+2amps
Volt .................................................... 120/240 VAC
Watt ................................................... 495 watts
Current ............................................... 5.8/2.9 amps
Resistance across terminals:
Above 42°F +5° .................................. Open
Below 12 °F +7° .................................. Closed
Volt ..................................................... 115 VAC
Wattage ............................................. 450 _+5%watts @ 115VAC
Resistance ......................................... 29 _+5% ohms
Volt ..................................................... 115 VAC
Wattage ............................................. 350 -+5% watts @ 115VAC
Resistance ......................................... 37.8 _+5%ohms
Volt ..................................................... 120VAC, 60 HZ
See Control board troubleshooting section
Rotation (facing end opposite shaft) Power to blue and white is clockwise. Power to orange and white is
counterclockwise
RPM ................................................... 17+ 3 RPM
Watts .................................................. Brown side 35w,YelIow side 20w
Rotation (facing end opposite leads) Counterclockwise
RPM .......................................... 1530 + 250
Watt .......................................... 1.2 @ 12 VDC
Type ............................................ SPDT NO/NC
Volt ............................................. 125/250 VAC
Current ......................................... 8/4 amps
Resistance across leads .................... 1Olohms + 10%
Service Specifications
I WARNING ]
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires
removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.
Programming Mode:
NOTE: The Program Code is located on the Serial Plate on this unit after the word Code.
.
.
3.
4.
.
.
Open the Fresh Food door and press and hold the Door Alarm Keypad
Press and hold Freezer Temperature Down Keypad(_-I_.
Release the Door Alarm Keypad and wait 3 seconds.
The control will display PE to indicate the programming mode.
I Freezer O O r_<c_r _<Z_pl_ce O @ O O Refrigerator
Entry is confirmed by pressing the Freezer Temperature Down Keypad _ once more.
The control will display the current Program CODE. This value should be validated with the Program CODE printed on
the unit serial plate.
(_ Freezer o o_r _p_ace o ® o o Refrigerator
NOTE: If the Program CODE is correct, the Programming Mode is exited by closing the Refrigerator door(s).
7. Press the Refrigerator Temperature UP Keypad _ or Refrigerator Down Keypad ([_) to change the digit value
with each key press.
8. The decimal point indicates the selected digit. Press the Freezer Temperature UP Keypad (_ to select the next
digit.
9. Once the desired Program CODE is displayed, press and hold the Freezer Temperature DOWN Keypad (_ until the
Program CODE begins flashing indicating it has been saved.
NOTE: If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will
NOT run with a Program CODE of 0000).Once the Program CODE has been saved the Programming Mode is
exited by closing the Refrigerator door(s). If the new code is incorrect this process should be repeated after closing
the Refrigerator door(s).
The Programming mode can be exited at any time by closing the Refrigerator Door(s) or will exit if unattended for
four minutes.
Defrost Operation:
The Control Board adapts the compressor run time between defrosts to achieve optimum defrost intervals by
monitoring the length of time the defrost heater is on. After initial power up, defrost interval is 4 hours compressor run
time. Defrost occurs immediately after the 4 hours.
December 2004 2 12893007 December 2004 3 12893007

Service Specifications
IWARNING I
To avoidriskofelectricalshockthatcan cause deathorseverepersonalinjury,disconnectunitfrompower before
servicingunlesstestsrequire power.Dischargecapacitorsthrougha 10,000-ohmresistorbeforehandling.Wires
removed duringdisassemblymust be replacedon correctterminalstoensure propergroundingand polarization.
Forced Defrost Mode:
The forced defrost function is performed using the Freezer display and Refrigerator keypad. Enter the
Forced Defrost Mode by performing the following sequence of events:
1. Open the Fresh Food door and press and hold the Door Alarm Keypad _.
2. Press and hold Refrigerator Temperature Down Keypad(_.
3. Release the Door Alarm Keypad and wait 3 seconds. FD appears in left display
'/ Freezel o@_ _,_ _ _ _ Refrigerator
4. Press the Refrigerator Down Keypad _ again. SH appears in right display.
5. Press again to force defrost Fd and SH will flash in display indicating unit is in defrost.
Service Test Mode:
The service test functions are performed using the refrigerator display and keypad. Enter the Service Test Mode
by performing the following sequence of events.
1. Open the Fresh Food door and press and hold the Door Alarm Keypad
2. Press and hold Refrigerator Temperature UP Keypad(_.
3. Release the Door Alarm Keypad and wait 3 seconds.
L Freezer Or_r _p,_0_@ _ _ _ Refrigerator S
4. Press the Refrigerator Down Keypad L.._T_Jagain.
5.
.
Display will show 001 in left display and numeric or dashes in right display.
Press Freezer Up Keypad (_ and Freezer Down Keypad _ to toggle through Service Test numbers.
Service Test - 101 Defrost Heater & Defrost Circuit
•Press the Refrigerator Up keypad (_ and Refrigerator Down keypad _to energize or de-energize the
Defrost circuit. The display will read OFF when de-energized OP when energized with open defrost thermostat
and CL when energized with closed defrost thermostat.
Service Test - 102 Compressor /Condenser Fan
• Press the Refrigerator Up keypad _ and Refrigerator Down keypad _ to toggle
Compressor/Condenser fan On and Off.
Service Test- 111 Fresh Food Fan (if equipped)
• Press the Refrigerator Up Keypad _ and Refrigerator Down Keypad _ to toggle
Fresh Food Fan On and Off.
NOTE: Display will show state OFF or DC voltage
December 2004 4 12893007

Service Specifications
I WARNING I
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires
removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.
Service Test- 112 Freezer Fan
•Press the Refrigerator Up keypad (_ and Refrigerator Down keypad _ to toggle Freezer Fan On and Off.
NOTE: Display will show state OFF or DC voltage.
Service Test - 121 Damper Operation
• Press the Refrigerator Up keypad _ and Down keypad (_ to toggle Damper (OP) open and (CL) closed.
NOTE: If damper is opening or closing it will not allow you to toggle damper and beep. Display will show state -CL or -OP
if Damper is in the process of closing or opening.
Service Test- 131 (3) Door Bottom Freezer Mullion Heater
• Press the Refrigerator Up Keypad _ and Refrigerator Down Keypad _ to toggle Mullion Heater Off and On.
Service Test- 141 Fresh Food Thermistor
• Will Show Fresh Food Temperature or OP for open thermistor or SH for shorted thermistor.
Service Test - 142 Freezer Thermistor
• Will Show Freezer Temperature or OP for open thermistor or SH for shorted thermistor.
Service Test - 143 Machine Compartment Thermistor
• Will Show Machine CompartmentTemperature or, OP open thermistor or SH shorted thermistor.
Service Test - 151 Fresh Food Door State
• Will show state of Fresh Food Door. OP (open) CL (closed).
NOTE: By pushing fresh food door switch you can toggle state from OP (open) to CL (closed).
Service Test - 152 Freezer Food Door State
• Will show state of Freezer Door. OP (open) CL (closed).
NOTE: By pushing freezer door switch you can toggle state from OP (open) to CL (closed).
Service Test - 161 Cube Dispenser (if equipped)
• Display shows the state of the Cube Dispenser (ON or OFF).
NOTE: By pushing Actuator pad you can control state of cube dispenser without opening Ice Chute door.
Service Test - 162 Crusher Dispenser (if equipped)
• Display shows the state of the Crusher Dispenser (ON or OFF).
NOTE: By pushing Actuator pad you can control state of Crusher dispenser without opening Ice Chute door.
Service Test - 163 Water Dispenser (if equipped)
• Display shows the state of the Water Dispenser (ON or OFF).
NOTE: By pushing Actuator pad or Bottle fill you can control state of Water dispenser.
December 2004 5 12893007

Service Specifications
I & WARNING I
To avoidriskofelectricalshockthatcan cause deathor severepersonalinjury,disconnectunitfrompower before
servicingunlesstestsrequire power.Dischargecapacitorsthrougha 10,000-ohmresistorbeforehandling.Wires
removed duringdisassemblymust be replacedon correctterminalstoensure propergroundingand polarization.
Service Specifications
IWARNING
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires
removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.
Service Test - 164 Ice Chute Dispenser (if equipped)
• Display shows the state of the Ice Chute dispenser (ON or OFF).
NOTE: By pushing Actuator pad you can control state of Ice Chute Dispenser.
Service Test- 165 Dispenser Lamp (if equipped)
• Display shows the state of the Dispenser Lamp (ON or OFF).
NOTE: By pushing Actuator pad or Bottle fill you can control state of dispenser lamp.
Service Test- 171 Actuator Pad (if equipped)
• Display shows the state of the Actuator Pad (ON or OFF).
Service Test - 172 Sports Fill (if equipped)
• Display shows the state of the Sports Fill (ON or OFF).
Service Test- 173 Ambient Light (if equipped)
• Display shows light sensor measurement (Hi or Lo). Night light will turn on light sensor measures Lo.
By changing the sensor's exposure to ambient light you can control the sensor measurement.
Service Test - 174 Water Actuator Bottom Mount Internal Dispenser (if equipped)
• Display shows the state of the Water Valve (ON or OFF).
NOTE: By pushing Water Actuator you can control state of Water Valve On or Off.
Service Test- 175 Dispenser Line (if equipped)
• Display shows the state of the Dispenser Line (ON or OFF).
NOTE: By pushing Actuator pad or Bottle fill you can change state of Dispenser Line.
Service Test - 181 Keypad Operation
• Display shows a numeric or letter display indicating the last key pressed.
NOTE: Refrigerator Up/Down keypads have no effect when pressed and Freezer Up/Down keypads
remain operational.
Service Test- 182 LED Indicator Operation
• Press the Refrigerator Up Keypad_ to show operation of LED Indicators. All LED Indicators will flash.
Press twice and LED will stop flashing.
Service Test - 191 Ice Maker Water Valve
• Display shows the state of the Ice Maker Water Valve (ON or OFF).
Service Test - 201 Mullion Heater Override (if equipped)
• Press the Refrigerator Up Keypad _or Refrigerator Down Keypad _ to change Mullion Heater from cycling on
with compressor (Off position) to 100% operation (On Position).
Service Test - 202 Default Defrost Operation
• Press the Refrigerator Up Keypad (_or Refrigerator Down Keypad _ to change Defrost Operation from normal
adaptive defrost (Off position) to minimum time between defrosts (On position).
Service Test - 203 Show Temperature Set points
• Press the Refrigerator Up Keypad (_or Refrigerator Down Keypad _ to change from showing actual
temperature (Off position) showing temperature set points only (On position).
Service Test - 211 Fresh Food Temperature Adjustment
• Press the Refrigerator Up Keypad (_or Down Keypad _ to change calibration of Fresh Food Temperature plus
or minus in 1°F increments up to -- 6°F.
NOTE: Temperature will read in Fahrenheit regardless of what current temperature scale is being used.
Service Test - 212 Freezer Temperature Adjustment
• Press the Refrigerator Up Keypad _or Down Keypad (_ to change calibration of Freezer Temperature plus or
minus I°F in increments up to --6°F.
NOTE: Temperature will read in Fahrenheit regardless of what current temperature scale is being used.
Service Test - 221 Reset Default Settings
Press the Refrigerator Up Keypad (_ and Down Keypad (_ to force to dEF (default factory settings).
December 2004 6 12893007 December 2004 7 12893007

Wiring Diagram
I & WARNING I
To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before
servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires
removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.
12921601 PRINTED I U,SA.
December 2004 8 12893007