Kenmore 795.7105 series User manual

Panel PCs
USER’S MANUAL
VER. 2.0 • 2003
No part of this manual may be reproduced without permission
FPB 1x02 Series
FPB 1502-C850 15ƎTFT Flat-Panel PC
w/850 MHz Pentium III CPU (1024 x 768)
FPB 1502-L700 15ƎTFT Flat-Panel PC
with 700 MHz Celeron CPU (1024 x 768)
FPB 1202-C850 12.1ƎTFT Flat-Panel PC
w/850 MHz Pentium III CPU (800 x 600)
FPB 1202-L700 12.1ƎTFT Flat-Panel PC
with 700 MHz Celeron CPU (800 x 600)
®
CyberResearch®, Inc.
www.cyberresearch.com
25 Business Park Dr., Branford, CT 06405 USA
203-483-8815 (9am to 5pm EST) FAX: [phone]

iii
©Copyright 2003
All Rights Reserved.
2003
The information in this document is subject to change without prior notice
in order to improve reliability, design, and function and does not represent
a commitment on the part of CyberResearch, Inc.
In no event will CyberResearch, Inc. be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use of or inability
to use the product or documentation, even if advised of the possibility of
such damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of CyberResearch, Inc.
Trademarks
“CyberResearch,” and “FPB 1x02 Series,” are trademarks of
CyberResearch, Inc. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.
• NOTICE •
CyberResearch, Inc. does not authorize any CyberResearch product for
use in life support systems, medical equipment, and/or medical devices
without the written approval of the President of CyberResearch, Inc. Life
support devices and systems are devices or systems which are intended
for surgical implantation into the body, or to support or sustain life and
whose failure to perform can be reasonably expected to result in injury.
Other medical equipment includes devices used for monitoring, data
acquisition, modification, or notification purposes in relation to life
support, life sustaining, or vital statistic recording. CyberResearch
products are not designed with the components required, are not subject
to the testing required, and are not submitted to the certification required
to ensure a level of reliability appropriate for the treatment and diagnosis of
humans.

iv
Intentionally Blank

Chapter 1 General Information ......................................... 1
Introduction................................................................................................2
Specifications..............................................................................................3
General............................................................................................3
Environmental................................................................................3
Rear View ......................................................................................3
Features...........................................................................................4
Detailed Specifications...................................................................6
Touchscreen (Optional).............................................................................8
Order Information.....................................................................................9
LCD Specification ....................................................................................10
Dimensions ............................................................................................11
Panel Mounting ........................................................................................13
Packing List ............................................................................................14
Chapter 2 ........................................................................... 15
Install a 3.5ƎHDD....................................................................................16
Install a Slim CD-ROM, FDD and 2.5ƎHDD`......................................17
Chapter 3 CPU Card General Information .................... 19
Introduction ............................................................................................20
Features ............................................................................................21
Specifications............................................................................................22
Board Layout............................................................................................25
Board Dimensions ....................................................................................26
Chapter 4 Installation........................................................ 27
Jumpers and Connectors.........................................................................28
Locating Jumpers.....................................................................................30
Locating Connectors................................................................................31
Setting Jumpers........................................................................................32
CPU Installation and Upgrade ...............................................................33
Installing SDRAM (DIMMs) ..................................................................35
System Memory........................................................................................35
Supplementary Information about DIMM............................................35
Memory Installation Procedures............................................................35
DOC Address & CPU Frequency Ration Select SW1 (S1~S6)............36
DOC Address Select.................................................................................36
LCD Clock Signal & Driving Voltage Select (J1) .................................37
COM2 RS-232/422/485 Select (J2, J3) ...................................................38
Clear CMOS (J4) .....................................................................................39
Power Connectors P8 & P9 (PWR 1).....................................................40
USB Connector (CN1) .............................................................................41
Display Connectors (CN8, CN2).............................................................42
VGA Display Connector (CN8) ..............................................................43
v

LCD Display Connector (CN2)...............................................................44
Keyboard and PS/2 Mouse Connector (CN3, CN5)..............................45
Parallel Port Connector (CN4) ...............................................................47
Parallel Port IRQ .....................................................................................48
Parallel Port Connector Table (CN4) ....................................................48
Serial Ports (CN11, CN5) ........................................................................49
IrDA Connector (CN6, Pin 1~5) .............................................................50
Reset switch (CN6, Pin 6,7) .....................................................................51
External/internal speaker (CN6, Pin 8~11) ...........................................52
Hard drive LED (CN6, Pin 13, 14) .........................................................53
CPU fan power connector (CN7)............................................................54
100Base-Tx Ethernet connector (CN9) ..................................................55
IDE hard drive connector (CN10)..........................................................56
IDE hard drive connector table..............................................................57
Floppy drive connector (CN12) ..............................................................58
Connecting the floppy drive....................................................................59
Floppy drive connector table ..................................................................60
DiskOnChip socket (U10)........................................................................61
DiskOnChip (DOC) 2000 Installation....................................................62
Chapter 5 Award BIOS Setup .......................................... 63
Starting Setup...........................................................................................64
Setup Keys ............................................................................................65
Getting Help ............................................................................................66
In Case of Problems.................................................................................66
Main Setup Menu.....................................................................................67
Standard CMOS Setup............................................................................69
BIOS Features Setup ...............................................................................75
CHIPSET Features Setup .......................................................................78
Power Management Setup ......................................................................82
PNP/PCI Configuration Setup................................................................87
Load BIOS defaults/Load setup defaults...............................................89
Integrated peripherals setup...................................................................90
Supervisor/User password setting ..........................................................93
IDE HDD auto detection .........................................................................95
Save & exit setup......................................................................................96
Chapter 6 Flat Panel/CRT controller Display Drivers and
Utilities ........................................................................... 97
Software drives.........................................................................................98
Hardware configuration..........................................................................98
Necessary prerequisites ...........................................................................99
Before you begin.......................................................................................99
Windows 95 ..........................................................................................100
Driver installation ..................................................................................100
Windows 3.51..........................................................................................108
vi

Driver installation ..................................................................................108
Windows NT 4.0.....................................................................................109
Driver installation ..................................................................................109
Chapter 7 Ethernet Software Configuration ............... 111
Ethernet software configuration...........................................................112
Appendix A Programming the Watchdog Timer........ 113
Programming the watchdog timer .......................................................114
Configuration register ...........................................................................114
Setting the Watchdog Timer.................................................................115
Product Service ................................................................ 121
Warranty Notice .............................................................. 123
vii

viii
Intentionally Blank

1
Chapter 1 General Information

2
Introduction
The FPB 1202/1502 panel PC series is a PC-based, industrial integrity
computer especially designed to keep normal operation under
harsh environment, which meet the entire requirement as an industrial man
machine interface (MMI).
They provide a complete hard ware application and construct a high quality
plastic front panel NEMA 4/12 which meets the toughest industrial and
environmental protection standards
It isa full-function PC-base system with a10.4” VGA(640 x 480), 12.1” SVGA
(800 x 600), 15.1” XGA (1024 x 768) color TFT hi-brightness, and long-life
LCD display. The compact dimensions are ideal for automation applications
when the installation space is critical.
These PCs are characterized by their space saving, there are two free slots
for PCI/ ISA. FPB 1202/1502 series is a heavy-duty steel chassis with a
sealed plastic front panel. meets the toughest industrial and environmental
standards.All the controls and connectors are placed on the rear panel, you
can connect the panel PCs to other devices via them.

Chapter 1 General Information
3
Specifications
General
 Construction: Heavy-duty aluminumchassis & NEMA
4/12 plastic or aluminum front panel
 Disk drive housing:
a 3.5" HDD or a 2.5”HDD, Slim CD-ROM &
Slim FDD.

 Gross Weight: 9.6 Kg
 Dimensions (FPB 1202): 346(W) x 271(H) x 126mm(D)
 Gross Weight: 10 Kg
 Dimensions (FPB 1502): 420(W) x 300(H) x 139mm(D)
 Gross Weight: 13.6 Kg
Environmental
 Operating temperature:0° to 50°
 Storage temperature: -20° to 60°
 Relative humidity: 5 to 95%, non-condensing
 Altitude: 10,000 ft. (3000 meters)
 Vibration:
5 to 17 Hz, 0.1" double-amplitude displacement
17 to 500 Hz, 1.5G peak to peak
 Shock: 10G-peak acceleration (11-msec. duration)
 Safety: meets UL/CSA/TUV
 EMI: FCC/CE Class A
Rear View picture
 NEMA 4/12 plastic front panel
 Outside connectors
 Drive bay
 30 CFM cooling fan
 Power switch
 Power inlet & fuse

4
Features
FPB 1202 (12.1”LCD + ACS-2303 Control Box)
 12.1” SVGA color TFT LCD display
 Heavy-duty steel chassis and NEMA 4/12
compliant plastic front panel
 All-in-one SBC, Celeron 700MHz/ P III 850MHz CPU,
256MB SDRAM, Ethernet, VGA.
 One RS-232 and one RS-232/422/485 serial port
 Disk Driver Space for CD-ROM, FDD and HDD
 DiskOnChip flash disk socket
 Print Port
 Expansion IDE/Floppy connectors***
 Touch Screen (optional)
 USB port (optional)
***Expansion IDE port will not functional when both HDD & CD-ROM
install in the machine

5
FPB 1502 (15”LCD + ACS-2303 Control Box)
 15” XGA color TFT LCD display
 Heavy-duty steel chassis and NEMA 4/12
compliant plastic front panel
 All-in-one SBC, Celeron 700MHz/ P III 850MHz CPU,
256MB SDRAM, Ethernet, VGA.
 One RS-232 and one RS-232/422/485 serial port
 Disk Driver Space for CD-ROM, FDD and HDD
 DiskOnChip flash disk socket
 Print Port
 Expansion IDE/Floppy connectors
 Touch Screen (optional)
 USB port (optional)
***Expansion IDE port will not functional when both HDD & CD-ROM
install in the machine

6
FPB 1202 (12.1”LCD + ACS2303 Control Box)
 Construction: Heavy-duty steel chassis &
NEMA 4/12 plastic front panel.
 CPU: Intel Celeron 700MHz or P III 850MHz
 Memory: 256MB SDRAM
 Display: 12.1” SVGA (800 x 600) TFT color LCD
 LCD/CRT controller:
C&T 69000 VGA controller with 2MB embedded
SDRAM. CRT & LCD panel support
 Network (LAN):
Intel 82559ER 10/100 Base-T Ethernet controller
 I/O ports:
Win bond W83977
COM1: RS-232
COM2: RS-232/422/485
1 parallel port (support ECP/EPP)
1 keyboard port
1 PS/2 mouse interface
Disk Driver Housing:
3.5”HDD or 2.5”HDD and 3.5”FDD or 2.5”HDD
and Slim-size CD-ROM
 USB connector: Dual USB ports onboard
 Mounting: Panel mount or Wall mount (ACS-2303
Control Box only, optional)
 Power supply: Universal 70W switching power
supply
Detailed Specifications

7
FPB 1502 (15”LCD + ACS2303 Control Box)
 Construction: Heavy-duty steel chassis &
NEMA 4/12 plastic front panel.
 CPU: Intel Celeron 700MHz or P III 850MHz
 Memory: 256MB SDRAM
 Display: 15” XGA (1024 x 768) TFT color LCD
 LCD/CRT controller:
C&T 69000 VGA controller with 2MB embedded
SDRAM. CRT & LCD panel support
 Network (LAN):
Intel 82559ER 10/100 Base-T Ethernet controller
 I/O ports:
Win bond W83977
COM1: RS-232
COM2: RS-232/422/485
1 parallel port (support ECP/EPP)
1 keyboard port
1 PS/2 mouse interface
Disk Driver Housing:
3.5”HDD or 2.5”HDD and 3.5”FDD or 2.5”HDD
and Slim-size CD-ROM
 Disk Driver Housing:
3.5”HDD or 2.5”HDD and 3.5”FDD or 2.5”HDD
and Slim-size CD-ROM
 USB connector: Dual USB ports onboard
 Mounting: Panel mount or Wall mount (ACS-2303
Control Box only, optional)
 Power supply: Universal 70W switching power
supply.
Power Supply Selection Table
Max. Output Current
Mode Input voltage +5V +12V -12V
Universal/70W 85-265VAC 12A 2.5A 0.3A
24VDC/70W 10-30VDC 12A 2.5A 0.3A

8
Touchscreen (Optional)
 Type: 4/8-wire, analog resistive
 Resolution: Continuous
 Light transmission: 72% (surface 4H, meets
ASTM-D-3363-92A standard.)
 Operating pressure: <50 grams for finger, <25 grams
for stylus pen. Contact bounce< 10ms
 Controller: RS-232 interface
 Power consumption: +5V @200mA
 OS support: MS DOS, Windows 3.1, Windows 95,
Windows 98, Windows NT, Windows2000

9
Order Information
FPB 1502-C850: 15" TFT Flat-Panel PC, 850 MHz Pen. III (1024 x 768)
FPB 1502-L700: 15" TFT Flat-Panel PC, 700 MHz Celeron (1024 x 768)
FPB 1202-C850: 12.1" TFT Flat-Panel PC, 850 MHz Pen. III (800 x 600)
FPB 1202-L700: 12.1" TFT Flat-Panel PC, 700 MHz Celeron (800 x 600)

LCD Specifications
Model FPB 1502 FPB 1202
Display type TFT color LCD TFT color LCD
Size (diagonal) 15” 12.1”
8Number of
Pixels
1024(W) x
768(H) 800(W) x 600(H)
Dot size
(mm x mm)
0.313(W) x
0.329(H)
0.3075(W) x
0.3075
Contrast ratio 300 250
View angle
(Horizontal) 160° 120°
View angle
(Vertical) 160° 100°
Luminance
(cd/m2 ) 250 250
LCD model
Fujitsu
FLC3XGC6V-0
6
Toshiba
LTM12C289
Operating
Temperature 0 ~ 50 °C 0 ~ 50 °C
Backlight
Life-time (Hrs) 25,000 25,000
10

Dimensions
FPB 1202
(mm)
Cutout (suggestion)
The FPB 1202 series will stand on a shelf or a table or you can
mount it into a panel. Cutout panel dimensions are the following:
(mm)
H x V: 333mm x 258mm
11

ON/OFF
DEC
INC
Cutout (suggestion)
The FPB 1502 series will stand on a shelf or a table or you can
mount it into a panel. Cutout panel dimensions are the following:
(mm)
H x V: 398mm x 278.4mm
12
FPB 1502