Kenmore 796.4138 series User manual

Use & Care Guide
Manual de Uso y Cuidado
EngJish /Espafiol
For best _es._is, a ow-suds r g HE .fgb f_'fic e'_cy
be used,
Model/Modelo: 796.4138 _
I('.enmoreo @
omalic
auto_itica de
=_ coloF numb®_, _'_6me_'ode co/o_
MFL67683493
vet.050514,00
Sears Brands Management Corporation
Hoffman Estotes, IL 60179 U.S.A.
www.kenmore.com
www.seors.com

iMPORTANT SAFETY INSTRUCTIONS ......................... 3-5
GROUNDING REQUIREMENTS ...................................... 5
FEATURES AND BENEFITS
Key Parts and Components ................................................. 6
Included Accessories ........................................................... 6
Optional Accessories ........................................................... 6
INSTALLATION REQUIREMENTS
Key Dimensions and Specifications ................................... 7
Choose the Proper Location ............................................... 7
Flooring .................................................................................. 7
Clearances ............................................................................. 7
INSTALLATION INSTRUCTIONS
Unpacking and Removing Shipping Bolts......................... 8
Connecting the Water Lines................................................ 9
Connecting the Drain Hose ............................................... ]0
Connecting to the Power Supply ....................................... 10
Leveling the "Washer ............................................................ 11
Installation of Non-Skid Pads ............................................. 11
HOW TO USE
Control Panel Features ........................................................ 12
Operating the Vv_asher......................................................... 13
Cycle Guide .................................................................... 14-15
Sorting _A/ashLoads ............................................................ 16
About the Dispenser Drawer .............................................. 17
Detergent and Dispenser Use............................................. 18
Magnetic Door Plunger ...................................................... 18
Time and Status Display .................................................... 19
Cycle Modifier Buttons ....................................................... 20
Steam Cycles and Options ................................................ 21
Steam Treat Option ......................................................... 21
Option Buttons .................................................................... 22
Delay Staff ........................................................................ 22
Extra Rinse....................................................................... 22
Pre Wash ........................................................................... 22
Special Functions ................................................................. 23
Control Lock ....................................................................... 23
Clean Washer ................................................................. 23
My Cycle ........................................................................... 23
Auto Soak ......................................................................... 23
Stay Fresh........................................................................... 23
CARE AND CLEANING
Regular Cleaning ........................................................... 24-25
Cleaning the Exterior ..................................................... 24
Care and Cleaning of the interior .................................24
Clean Washer ................................................................ 24
Door Seal and Glass Cleaning ...................................... 24
Removing Mineral Buildup .............................................. 24
Storing the VVasher ......................................................... 25
leaning the Dispenser .................................................. 25
Maintenance ................................................................... 26-27
Cleaning the VCater Inlet Filters ..................................... 26
Cleaning the Drain Pump Filter ......................................27
KENMORE CONNECT TM System.......................................... 28
TROUBLESHOOTING GUIDE
Normal Sounds You May Hear, ........................................ 29
Before Calling for Service ........................................... 29-31
WARRANTY ................................................................. 32
In the space below_record the date of purchase,modeb
and serial number of your product. You will find the model and
serial number printed on an identification plate located inside
the washer door, Have these items of information available
whenever you contact Sears concerning your product,
Model No,
Date of Purchase
Serial No.
Save these instructions and your sales receipt for future
reference.
Master Protection Agreements
Congratulations on making a smart purchase. Your new
Kenmore Qproduct is designed and manufactured for
•/ears of dependable operation. But llke all products, it
may require preventh, e maintenance or repair from time
to time. That's when having a Master Protection
Agreement can save you money and aggravation.
The Master Protection Agreement also helps extend the
life of your new product. Here's what the Agreement _
includes:
• Parts and labor needed to help keep products
operating properly under normal use, notjust defects.
Our coverage goes well beyond the product warranty.
No deductible, no functional failure excluded from
coverage - real protection.
•Expert service by a force of more than 10,000
authorized Sears service technicians, which means
someone you can trust will be working on your product.
• Unlimited service calls and nationwide service, as
often as you want us,"wheneveryou ,want us.
."No-lemon" guarantee - replacement of your covered
product if four or more product failures occur within
twelve months.
•Product replacement if your covered product can not
be fixed,
• Annual Preventive Maintenance Check at your request
- no extra charge.
• Fast help by phone - we call it Rapid Resolution.
Phone support from a Sears representativeon all
products.Thinkof usas a "talking owner'smanual."
• Power surge protection against electric damage due to
power fluctuations.
"$250 food loss protection annually for any food
spoilage that isthe result of mechanical failure of any
covered refrigerator or freezer.
•Rental reimbursement if repair of ,/our covered
product takes longer than promised.
•25% discountoff the regular price of an,/non-covered
repair service and related installed parts.
Once you purchase the Agreement, a simple phone
call is all that it takes for you to schedule service. You
can call at any time day or night or schedule a service
appointment online.
The Master Protection Agreement is a risk-free purchase.
If you cancel for any reason during the product
warranty period, we will provide a full refund, or a
prorated refund any time after the product -warranty
period expires. Purchase your Master Protection
Agreement today!
Some limitations and exclusions apply.
For prices and additional information in the U.S.A.
call 1-800-827-6655.
*Coverage in Canada varies on some items.
For full details call Sears Canada at 1-800-361-6665.
Sears Installation Service
For Sears professional installation of home appliances,
garage door openers, water heaters, and other major
home items, in the U.S.A. or Canada call:
1-800-4-MY-HOME ®.

Therearemanyimportantsafetymessagesinthismanualandonyour appliance. AF_¢aysread and obey
all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can result in property
damage and/or serious bodily harm or death.
Aft safety messages will follow the safety alert symbol and either the word DANGER or "vVARNING.
These words mean:
indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
Indicates a hazardceJSsituation which, if not avoided, could result in death or serious
injury.
All safety messages will tell you what the potential hazard is,tell you how to
reduce the chance of injury, and tell you what can happen if the instructions are
not followed.
To reduce the risk of fire, electric shock, or injury to
persons when using this appliance, follow basic
precautions, including the following.
"Before use,the washer must be properly installed as
described in this manual.
•Do not wash articles that have been previously cleaned
in, "washedin, soaked in, or spotted with gasoline, dry
cleaning solvents, or other flammable or explosive
substances, as they give off vapors that could
ignite or explode.
•Do not add gasoline, dry cleaning solvents, or other
flammable or explosive substances to the wash .water.
These substances give off ,vapors that could ignite
or explode.
•Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS IS
EXPLOSIVE. ff the hot water system has not been used
for such a period, before using the washer, turn ON
all hot water faucets and let the water flow from each
for several minutes. This will release any accumulated
hydrogen gas. As the gas is flammable, do not smoke
or use an open flame during this time.
•Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is
used near children.
•Before the washer is removed from service or
discarded, remove the door to prevent children from
climbing inside.
•Do not install or store the washer where it will be
exposed to the weather or freezing temperatures
• Do not tamper with controls.
•Do not repair or replace any part of the washer or
attempt any servicing other than as described in this
manual. We strongly recommend that any service be
performed by a qualified technician.
• See Installation instructions for grounding requirements
•ALV'/AYSfollow the fabric care instructionssupplied by
the garment manufacturer.
•Do not place items exposed to cooking oil in your
washer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
•Use fabric softeners or products to eliminate static only
as recommended by the manufacturer.
•This washer is not designed for maritime use or for
mobile installations such as in RVs,aircraft, etc.
•Turn OFF the water faucets and unplug the washer if
the machine isto be left for an extended period of
time, such as during vacations.
•Packaging material can be dangerous for children.
There is a risk of suffocation. Keep all packaging
from children.
•Always check the inside of the washer for foreign
objects before loading laundry. Keep the door closed
when not in use.
•Warning: This product contains chemicals known to the
State of California to cause cancer and birth defects
or other reproductive harm. Washhandsafter handling.

To reduce the risk of fire, electric shock, or injury to
persons when using this appliance, follow basic
precautions, including the following.
• Unplug the washer before cleaning to avoid the risk of
electric shock.
•Never use harsh chemicals, abrasive cleaners, or
solvents to clean the washer. They will damage
the finish.
• Do not put oily or greasy rags or clothing on top of
the washer. These substancesgive off vapors that
could ignite the materials.
*Do not wash items that are soiled with vegetable or
cooking oil. These items may contain some oil after
laundering and may catch fire.
•Disconnect this appliance from the power supply
before attempting any user maintenance. Turning the
controls to the OFF position does not disconnect this
appliance from the power supply. Failure to follow this
warning can cause seriousinjury,fire, electric shock,
or death.
"Do not combine detergents, fabric softeners, and/or
other laundry products from different manufacturers
for use in a load, unlessspecified on the fabric label.
•Do not mix chlorine bleach wffh ammonia or acids
such as vinegar. Follow package directions when
using laundry products. Incorrect usage can produce
poisonousgas, resultingin seriousinjury or death.
•Do not reach into the washer while parts are moving.
Before loading, unloading, or adding items, press
the PAUSEbutton and allow the drum to coast to a
complete stop before reaching inside. Failure to follow
this warning can cause serious injury,fire, electric shock
or death.
• Refer to INSTALLATION INSTRUCTIONS for detailed
grounding procedures. Installationinstructionsare
packed in the washer for the installer'sreference. If the
washer is moved to a new location, have it checked
and reinstalled by a qualified service technician. Failure
to follow this warning can cause serious injury, fire,
electric shock, or death.
• Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord. Failureto
follow this warning can cause serious injury, fire, electric
shock, or death.
• For personal safety, this appliance must be properly
grounded. Failure to follow this warning can cause
seriousinjury, fire, electric shock, or death.
• The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the possibility
of electric shockhazard from this appliance.
• This washer must be plugged into a 120VAC, 60Hz
grounded outlet. Failure to follow this warning can
cause serious injury, fire, electric shock,or death.
• Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is properly
grounded. Failure to follow this warning can cause
serious injury, fire, electric shock,or death.
• Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet. Failure to follow this warning can cause
serious injury,fire, electric shock, or death.
• Do not install on carpet. Install the washer on a solid
floor. Failure to follow this warning can cause serious
leak damage.
• Do not remove the grounding prong. Do not use
an adapter or extension cord. Plug into a grounded
3-prong outlet. Failure to follow these warnings can
cause serious injury,fire, electric shock,or death. 4
•The washer should always be plugged into its own
individual electrical outlet which has a voltage rating
that matches the rating plate. Thisprovides the best
performance and also prevents overloading house
wiring circuits which could cause a fire hazard from
overheated wires.
*Never unplug your washer by pulling on the power
cord. Always grip the plug firmly and pull straight
out from the outlet. Failure to follow this warning can
cause seriousinjury, fire, electric shock,or death.
*Immediately repair or replace all power cordsthat
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end. Consult with a
qualified service technician. Failure to follow this
warning can cause serious injury, fire, electric shock,
or death.
*When installing or moving the washer, be careful not
to pinch, crush, or damage the power cord. Failure
to follow this warning can cause seriousinjury, fire,
electric shock, or death.
*The washer must be installed and electrically
grounded by a qualified service technician in
accordance with local codes to prevent shock hazard
and assure stability during operation.
*The washer isheavy. Two or more people may be
needed to install and move the appliance. Failure
to do so can result in damage to property or serious
bodily injury.
*Store and install the washer where it will not be
exposed to temperatures below freezing or exposed
to outdoor weather condffions. Failure to follow this
warning can cause serious leak damage.
*To reduce the risk of electric shock, do not install
the washer in humid spaces. Failure to follow this
warning can cause seriousiniur_; fire, electric shock, or
death.

•Do not allow children to play on or in the washer. Close
supervision of children is necessary when the "washeris
used near children. As children grow, teach them the
proper, safe use of all appliances. Failure to comply with
these warnings could _sult in serious personal injury.
*Destroy the carton, plastic bag, and other packing
materials after the washer is unpacked. Children
might use them for play. Cartons covered with rugs,
bedspreads, or plastic sheets can become airtight
chambers. Failure to comply with these warnings could
result in serious personal injury.
•Keep laundry products out of children's reach. To
prevent personal injury, observe all warnings on
product labels. Failure to comply with these warnings
could result in serious personal injury.
•Before your washer is removed from service or
discarded, remove the door to the washing com_rtment
to avoid the danger of children or small animals
getting trapped inside. Failure to do so can result in
serious personal injury or death.
IMPORTANT: Please read carefully'.
TO CONNECT ELECTRICITY
Improper connection of the equipment-grounding
conductor can result in risk of electric shock. Check
with a qualified electrician or service technician
if you are in doubt as to whether the appliance
is properly grounded. Do not modify the plug
provided with the appliance. If it does not fit the
outlet, have a proper outlet installed by a qualified
electrician. Failure to follow these warnings can
cause serious injury, fire, electric shock, or death.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped
with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed and
grounded in accordance with all local codes
and ordinances.
3-prong
grounding type
wall receptacle-_
3-prong
grounding
plug
Ensure proper
ground exists
before use.
5

KEY PARTS AND COMPONENTS
ODETERGENT DISPENSER
There are four compartments. One each for prewash,
main wash, liquid bleach, and liquid fabric softener.
O ONTROL PANEL
The easy-to-read LEDdisplay showscycle options,
settings, cycle status, and estimated time remaining during
operation.
NOTE: Sensors in the washer automatically detect the
size of the wash load to optimize washing time, based
on the selected cycle and options.
OIRECT-DRIVE MOTOR
The direct-drive motor provides improved performance
and reliability while increasing energy efficiency.
(Motor is not visible.)
OARGE-CAPACITY STAINLESS STEELDRUM
The ultra-large stainless steel drum offers extreme
durability and istilted to improve emciency and allow
easier access for large items.
_ASY-ACCESS LOCKING DOOR
The extradarge door locksduring operation. The door
will not open until it issafe to do so.
O ILTERACCESS PANEL
Provideseasy access to the drain pump filter, which allows
you to clean the filter or retrieve lost itemswffhout a
service call.
_ EVELING FEET
Four leveling feet (two in the front and two in the back)
adjust to improve washer stability on uneven floors. Feet
are adjusted and locked in place usingthe adjusting
wrench included with the washer.
O IGH-EFFICIENCY STEAM CYCLES
During high-emciency steamcycles, hot steam intera_
with fabrics to help remove tough stains.
O OOR MAGNET
Safely and conveniently keep the door ajar with thedoor
magnet. The magnet keeps the door slightly open when
the washer isn't in useto promote air circul_ion and affow
the interiorof the machine to dry. Tousethis feature, after
the laundry has been removed, close the door just until it
contacts the door magnet.
included Accessories
Non-skid pads Caps (4)
(for covering
shipping bolt holes)
Wrench (for removing Tie Strap
sh{pp_ng baits and (for securing
adiusting and drain hose}
_Jocking leveling feet)
Wrench appearance may vary,
E}bow Bracket
(for securing
drain hose)
Power
Drain
Hose
Cold and hot water inlets
Rear of Washer
Shipping Bolts/Retainers (4)
NOTE: Bolts/Retainers MUST be removed prior to
operation, Keep for fl._,sreuse,
Optional Accessories ---"'_
Hot and Cold Water Hoses Drain Hose Extension
Pedestal
51022 (White)
51023 (Metallic Silver)
PiN 5215ER2002K
StackJng kit (For dryer)
f ............
D2617013 (Chrome Look}

|KEY DIMENSIONS AND SPECIFICATIONS
Description Front-Loading VVasher
Rated Voltage/Frequency 120VAC, 60Hz
Dimensions 27 in. (W) X 29 3/_in. (D) X 38 11/16in. (H), 51 in. (D, door open)
68.6 cm (W) X 75.6 cm (D) × 98.3 cm (H), 129.5 cm (D, door open)
Net Vv'eight 202.8 Ib (92kg)
CHOOSE THE PROPER LOCATION
WARNING
• This washer is heavy. Two or more people are
required when moving and unpacking the washer.
Failure to do so may result in damage to property or
serious bodily harm.
• Store and install the washer where it will not be
exposed to temperatures below freezing or exposed
to outdoor weather condfflons. Failure to follow this
warning can cause seriousinjury, fire, electric shock,
or death.
•Properly ground the washer to conform with all
electric governing codes and ordinances. Failure
to follow this warning can cause seriousinjury, fire,
electric shock, or death.
*To reduce the risk of electric shock, do not install the
washer in humid spaces. Failure to follow this warning
can cause seriousinjury, fire, electric shock, or death.
•To ensure proper air flow, do not block the large
opening on the boflom of the washer with carpeting
or other materials.
• Do not remove the ground prong. Do not use an
adapter or extension cord. Plug into a grounded
3-prong outlet. Failure to follow this warning can cause
serious injury, fire, electric shock, or death.
NOTE: Installing the washer in a humid space, or installing or
storing the -washerwhere it will be exposed to the weather
or freezing temperatures, may result in rustor other
damage that isnot covered by the product warranty.
Power O_let
•The power outlet must be within 60 in. (1.5 m) of either
side of the washer.
•The appliance and outlet must be positioned so that
the plug iseasily accessible.
•Do not overload the outlet with more than
one appliance.
*The outlet must be grounded in accordance with
current wiring electric codes and regulations.
•Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation of
the product owner to have a proper outlet installed by a
qualified electrician.
FLOORING
•To minimize noise and vibration, the washer MUST be
installed on a solidly constructed floor. See the NOTE
to your right.
•Allowable slope under the entire washer isa maximum
1 in. difference from side to side or from front to back.
•Installing on carpeting and soft tile surfaces is
not recommended.
°Never install the washer on a platform or weakly
suppofled structure. 7
CLEARANCES
I29 3/4" _ 4"
(75.6 cm) _-_! (10 cm)51"
(129.5 cm)
Toensure sumcient clearance for water lines and airflow,
allow minimum clearances of at least 1in_(2.5 cm) at the
sides and 4 in. (10 cm) behind the unit. Be sure to allow
for wall, door, or floor moldings that may increase the
required clearances.
27,,
(68.6 cm)(2,5 cm) (2.5 cm}
Allow at least 22 in. (55.9 cm) in front of
the washer to open the door.
NOTE: The floor must be strong and rigid enough to
support the weight of the washer, when fully loaded,
without flexing or bouncing. If your floor has too much
flex, you may need to reinforce it to make it more rigid.
A floor that isadequate for a top-loading washer may
not be rigid enough for a front loading washer, due to
the difference in the spin speed and direction, if the
floor is not solid, your washer may vibrate and you may
hear and feel the vibration throughout your house.

UNPACKING AND REMOVING SHIPPING BOLTS
When removing the "washerfrom the carton base, be sure
to remove the foam drum support in the middle of the
carton base. See drawing below.
If you must lay the washer down to remove the base
packaging materials, always protect the side of the
washer and lay it carefully on itsside. DO NOT lay the
washer on itsfront or back.
To prevent internal damage during transport, the washer
is equipped with four shipping bolts and plastic retainers.
IMPORTANT:
-These shipping bolts and retainers MUST NOT be
removed until just before moving the washer into its
final position,
-These bolts and retainers MUST be removed before
operating the washer.
•Failure to remove shipping bolts and retainers may
cause severe vibration and noise, which can lead to
permanent damage to the washer.
NOTE: The power cord issecured to the back of the
washer with a shipping bolt to help prevent operation
with shipping bolts in place.
f _'x
Power
Cord
J
1. Starting with the bottom two shipping bolts, use the
wrench (included) to fufly loosenall four shipping
bolts by turning them counterclockwise.
2. Remove the bolt assemblies by wiggling them
slightly while pulling.
3. Locate the four hole caps included in the accessory
pack and install them in the shipping bolt holes.
NOTE: Save the bolt assemblies for future use. To prevent
damage to internal components, DO NOT transport the
washer without reinstalling the shipping bolts.

CONNECTING THE WATER LINES
*IMPORTANT: Use new hoses when installing the
washer. Do NOT reuse old hoses.
•"Water supply pressure must be between 14.5 psi and
142 psi (100_980 kPa). If the water supplypressure is
more than 142 psi, a pressure reducing valve must be
installed.
•Periodically check the hosefor cracks, leaks, and wear,
and replace the hose if necessary.
•Make sure that the water lines are not stretched,
pinched, crushed, or kinked.
•The washer should never be installed or stored in a
location subjectto freezing temperatures. Damage to the
water linesand internal mechanisms of the washer can
result.If the washer was exposed to freezing temperatures
prior to installation, allow it to stand at room temperature
for several hoursbefore use and check for leaks prior
to operation.
Rubber Seal Rubber Seal
Water Hose
(to water inlet
on washer) (to tap)
Inspect the threaded fitting on each hose and make
sure there is a rubber seal in place in both ends.
Water
2. Connect the -water supply hosesto the HOT and
COLD water faucets tightly by hand and then tighten
another 2/3turn with pliers.
f
3. Always run a gallon or two of water through each
inlet hose to flush dirt, scale and other debris out
of the water lines. Doing so will help prevent future
problems with clogged filter screens,and will also
allow you to "verify which hose ishot and which
iscold.
Cold Water
Water Inlet
Inlet
4. Attach the (red) hot water line to the hotwater inlet on
the back of the "washer.Attach the (blue) cold water line
to the cold water inlet on the back of the washer.
Tighten the fittings securely.
NOTE: When installing the hosesonto the water
inlet valves, be careful not to cross-thread the hose
fittings. DO NOT overtighten the hoses; this could cause
damage to internal components, the -calve or the hose
gasket. Overtightening could result in property damage
from leaks.
9

CONNECTING THE DRAIN HOSE
-The drain hose should always be properly secured.
Failure to properly secure thedrain hosecan result in
flooding and propert¢ damage.
•Do not install the end of the drain hose higher than 96
in. (243.8 cm) above the bottom of the washer.
"The drain must be installed in accordance with any
applicable local codes and regulations.
-Make sure that the drain hose is not stretched, pinched,
crushed, or kinked.
NOTE:
Adrainhoseextensionkit is
available if thedrainhoseisnot
long enc___h.Do notextend the
drain hosemore than6 feet,as
thiswill cause pcx_draining,
which will _lt in poor wash
and spinperformar_:e.
Option 1: Standpipe
rain Hose
Install the end of the drain hose into the elbow bracket.
Do not extend the drain hose more than 4 inchespast the
end of the elbow bracket. Use a tie strap to secure the
drain hose in place.
NOTE:
•Total height of the hose end should not exceed 96 in.
(243.8 cm) from the bottom of the washer.
-The drain hose should be inserted no more than 8-t2
inches into the standpipe. Inserting more than 8-12
inches can cause mold or microorganisms to spread to
the inside of the washer.
If the water valves and drain are built
into the wall, fasten the drain hose
to one of the water hoses with the tie
strap (ribbed side on inside).
/
Tie Strap
Option 2: Laundry Tub
Drain Hose
The elbow bracket should be installed near the end of
the drain hose. Hang the end of the drain hose over the
side of the utility sink. Use a tie strap to secure the drain
hose in place.
Option 3: Floor Drain
Dra;n Hose
Floor Draln
Insert the end of the drain hose into the floor drain.
if possible, secure the hose to prevent it from moving or
coming out of the drain.
CONNECTING TO THE POWER SUPPLY
"Washer should be p_ugged intoa 120-VAC, 60-Hz
grounded 3_prong outlet. Plug in the washer.
10

LEVELING THE WASHER
Thedrum of your new washer spinsat very high speeds.
Tominimize vibration, noise,and unwanted movement,
the floor must be a level, solid surface.
NOTE: Adjust the leveling feet only as far as necessaryto
level the washer. Extending the leveling feet more than
necessary can cause the washer to vibrate.
NOTE: Before installing the washer, make
surethat the floor isclean, dry and free of
dust,dirt, water and oils sothe washer feet
cannot slide easily, Leveling feet that
move or slide on the floor can contribute
to excessvibration and noisedue to
poor contact with the floor. See
INSTALLATION OF NON-SKID PADS
for more information.
NOTE: If a drip pan must be used,make sureto follow the
instructions provided with thedrip pan and make surethe
leveling feet are adjusted for firm and even contact with
the pan. Useof drip pans and failure to properly level the
machine may result in increasedvibration and noise
during operation.
All four leveling feet must rest solidly on the floor. Rock
the washer from corner to corner to make sure that all
four leveling feet are in firm and even contact with the floor.
fLevel
Leveling Feet
1. Position the washer in its final location, taking special
care not to pinch, strain, or crush the water and drain
lines. Place a level across the top of the washer.
Raise
2. Loosen the iocknuts on all four leveling feet with
the wrench until you can adjust the feet (wrench
appearance may vary). Usethe wrench to turn the feet
clockwise to raise the washer, and counterclockwise
to lower the washer. Usinga level, adjust the feet until
the washer is level from side to side and front to back.
Make surethat all four feet are in firm contact with the
floor.
NOTE: if you are installing the washer on the optional
pedestal, the washer leveling feet should be fully retracted.
Use the leveling feet on the pedestal to level the washer.
Tighten all 4lock nuts
securely using the
wrench.
3. Once the washer is level from side to side and front to
back, use the adjusting wrench to tighten all four lock
nuts securely to prevent the legs from geffing out of
adjustment during operation. Make surethat all four
leveling feet are in firm contact with the floor.
NOTE: To make sure that the washer is properly level, run
the washer with a test load: place a medium-sized load
of laundry in the machine. Then, press POWER, select
RINSE & SPIN, and press the START/PAUSE button.
See the following sections for additional information on
cycle selection and operation. Verify that the washer does
not rock or vibrate excessively during the spin cycle. If the
washer vibrates or shakes, adjust the leveling feet, while
the washer is spinning, until the vibrations are reduced.
INSTALLATION OF NON-SKID PADS
Some floor surfaces are too slippery to prevent the
washer from moving on the floor during heavily
unbalanced loads. While it is normal for an occasional
load to be out of balance, excess noise and vibration can
result from the washer moving out of position, if these
conditions are encountered, follow the instructions below
for installation of the non-skid pads. These pads will help
prevent the washer from moving during heavy, out of
balance conditions, thereby reducing noise and vibration.
NOTE: The non-skid pads are included in the installation
packet.
Non-skid pads
This side up
Stick adhesive side to floor
Remove backing
:_ Piace the pads under both front feet.
11

WARNING: To reduce the risk of fire, electric shock, or injury to persons,read and follow this
entire Use & Care Guide, including the Important Safety Instructions,before operating this washer.
CONTROL PANEL FEATURES
Normal ! Casual
Bulky I Bedding
Kids _4eor
Heavy Duty
Whitest _/httes
STARTIPAUSE
Sanitize
Express Wash
Co_d Clean
Delicates
Rinse & Spin
II
O
O
O
POWER (ON/OFF) BUTTON
Pressto turn the washer ON or OFF.
NOTE: Pressing the POWER button during a
cycle will cancel that cycle and any load
settingswill be lost. The door will unlock after a
brief pause, unless the water level or
temperature is too high.
CYCLE SELECTOR KNOB
Turnthisknob to selectthedesired cycle.Once the
desired cycle has _n selected,the standard presets
will appear in the display. Thesesettings can be
adjusted usingthe cycle setting buttons any time
before starting the cycle.
START/PAUSE BUTTON
Press this button to start the selected cycle.
if the washer is running, use this button to pause
the cycle without losing the current settings.
NOTE: If you do not pressthe START/PAUSE
button within four minutes of selecting a cycle,
the washer automatically turnsOFF.
O
O
O
O
CYCLEMODIFIER BUTTONS
Use these buttons to adjust the settings for the
selected cycle. The settings light up above the
buttons to show the current selection.
SPECIAL CYCLE AND OPTION BUTTONS
These buttonsare used to activate special cycles
or options.
TIME AND STATUS DISPLAY
The display shows the cycle status, door lock
status and estimated time remaining.
STEAM TREAT BUTTON
Select the STEAM TREATbutton to add steam to
the selected cycle for added cleaning power.
NOTE: The steam option isnot available on all
cycles.
NOTE: To protect your clothing, not all settings are available on all cycle selections.
12

OPERATING THE WASHER
_ POWER
Nor_I 1C_I
Bulky !Bedding
Kids Wear
Heavy Duty
Whitest Whffes
\
;!
/
/
_nit_ze
Express Wash
Co_d C_Qan
De_cote_
...........:..................1
@
@
O
O
@
SORT LAUNDRY AND LOAD WASHER
Sort laundry by fabric type, soil level, color and load size,
as needed. Open the door and load selected items into the
washer.
TURN ON THE WASHER
Pressthe POWER button to turn ON the washer. The lights
around the cycle selector knob will illuminate and achime will
sound.
SELECTA CYCLE
Turn the cycle selector knob in either direction to select the
desired cycle. The preset VVashTemperature, Spin Speed, Soil
Level, and Option settings for that cycle will be shown.
SELECTCYCLE MODIFIERS & OPTIONS
Default settingsfor the selected cycle can now be changed if
desired. Use the cycle modifier buttons.
NOTE: To protect your fabrics, not all modifiers are available
on all cycles. Cycle options can also be added by using the
option buttons.
NOTE: Not all options are available on all cycles. A different
chime will sound and the LED will not come on if the selection
is not allowed.
ADD DETERGENT
Add High-Efficiency (HE) detergent to the detergent dispenser
drawer. For proper wash performance, always measure the
detergent using the measurements provided by the detergent
manufacturer.
START IPAUSE
OBEGIN CYCLE
Pressthe START/PAUSE button to begin the cycle. The door will
lock, and the washer will briefly tumble the load without water
to measure its weight. Once the weight of the load is measured,
the washer will begin the selected wash cycle.
Pressing the START/PAUSE button during the cycle wiiI pause
the cycle and the door will unlock. Pressthe START/PAUSE
button again to resume the wash cycle.
13

CYCLE GUIDE
The cycle guide below shows the default settings, available options and recommended fabric ty_
for each cycle. Allowable modifier adjustments are shown below the default setting for each cycle.
= Available Option
= Default Setting
Large items
SUCh aS
blankets and
comforters
Specifically
designed to
clean and
thoroughly
rinse kids
wear
Heavily
soiled
cotton fabrics
Heavily to
normally
soiled white
cottons
Heavily
soiled items,
such as work
clothes_
diapers, etc.
Hot
Tap Cold
Cold
Hot
Tap Cold
Cold
Warm
Tap Cold
Cold
Hot
Tap Cold
Cold
Warm
Tap Cold
Cold
Extra High
Medium
Low
No Spin
Low
No Spin
Extra High
Medium
Low
No Spin
High
Medium
Low
No Spin
Extra High
Medium
Low
No Spin
Extra High
Medium
Low
No Spin
*CERTIFIED BY NSF: NSF International (formerly the National Sanitation
Foundation), certifes that the Sanitize cycle reduces 99.9% of bacteria on
laundry, and none of the bacteria will carry over onto the next laundry load.
Protocoi P172
Sanitization Perbrmance of ResJdentiai and
Commercial, Family Sized Clothes Washers
NOTE:
•To protect your garments, not every wash temperature, spin speed, soil level, or option is available with every
cycle. A chime will sound and the LED will not light if the selection is not allowed.
•The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and other
operating conditions.
•These cycles use -variouswash motions to enhance cleaning and/or fabric care performance. The wash motions may sound
different at different stages of the wash cycle. Thisisnormal.
•The recommended load size for the Sanitize cycle is 10 lb.
]4

CYCLE GUIDE (continued) _ = Available Option
The cycle guide below showsthe default settings,available options and recommended fabric types
for each cycle. Allowable modifier adjustments are shown below the default setting for each cycle. = Default Setting
Express Lightly soiled
Wash clothing and
small loads
Small loads
of cotton_
Cold Clean linen, towels,
shirts, sheets,
jeans,mixed
loads
Dress shirts/
Dellcates blouses,
_or
Loads that
Rinse and only need to
Spin be rinsed Extra High
Medium
Low
No Spin
NOTE:
•To protect your garments, not every wash temperature, spin speed, soil level, or option is available with every
cycle. A chime will sound and the LED will not light if the selection is not allowed.
•The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and other
operating conditions.
•These cycles use,various wash motions to enhance cleaning and/or fabric care performance. The wash motions may sound
different at different stages of the "washcycle. This is normal.
•The recommended load size for the Sanitize cycle is 10 lb.
15

SORTING WASH LOADS
Fabric Care Labels
Many articles of clothing include a fabric care label.
Using the chart below, adjust the cycle and option
selections to care for your clothing according to the
manufacturer's recommendations.
fFabric Care Labels
Machine
wash
cycle _Jrm_ P_tmane_tp_
O0not _ _ n_t _lng
Water • • • O0 •
temperature _ war_ c0_l
Bleach
symbols A A
Anybi_ Ontynom_lo_'in__o_
(whenn_) (whenr_sd)
Donot_leach
Grouping Similar Items
Forthe best washing results,and to reduce the possibilityof
damage to clothing, care should be taken to sortthe
clothing into loadsthat are made up of similaritems.
Mixing different fabric types and/or soil levelscan result
in poor wash performance, color transfer or discoloration,
fabric damage or linting. Fabricsshould be sorted into
groups as described below.
Colors
Sort articles by color. VVashdark clothes together in a
separate load from light colors or whites. Mixing clark
clothes with light clothes can result in dye transfer or
discoloration of the lighter clothes.
Soil Level
W'ash heavily soiled clothing together. "W'ashing lightly
soiled clothing in the same load with heavily soiled
clothing could result in poor wash performance for the
lightly soiled clothing.
FabricType
Delicate articles should not be mixed -with heavier or
sturdier fabric types. _vVashingdelicates in a load with
heavy fabrics can result in damage to the more delicate
fabrics. Washing heavier fabrics in a delicate load can
result in poor wash performance for the heavier fabrics
and possible damage to the delicates.
LintType
Some fabrics attract and bind lint to them while others
give off lint in the laundry process. Avoid mixing these
lint collectors and lint producers in the same load. Mixing
these fabrics will result in pilling and linting on the lint
collectors. (For example, lint collector -knit sweater; lint
producer -terrycloth towels.)
Loading the Washer
•Check all pockets to make sure that they are empty.
Items such as clips, matches, pens, coins, and keys can
damage both ;,,our washer and your clothes.
•Close zippers, hooks, and drawstrings to prevent these
items from snagging or tangling on other clothes.
•Pretreat heavily stained areas for best results.
•Combine large and small items in a load. Load large
items first.
"Large items should not be more than half of the total
wash load.
•The drum should not be tightly packed with items. The
door of the washer should close easily.
•To prevent an out-of-balance load, do not wash
single items. Add one or two similar items to the load.
Large, bulky items, such as a blanket, comforter, or
bedspread, should be washed individually.
•Do not wash or spinwaterproof items, suchas rain
coats, sleeping bags, etc.
•When unloading the washer, check under the door seal
for small items.
NOTE: Make surethat the door seal area isclear when
closing the door. Overloading the washer can cause items
to get caught between the door and the seal. Thiscan
damage both the items and the seal.
* DO NOT OVERLOAD THE DRUM
- MAKE SURE CLOTHING IS NOT
CAUGHT IN THE DOOR GASKET
Ij Sort Laundry,.,
Iby Colors by Soil by Fabric by Lint
Whites Heavy Delicates Lint Producer
Lights Normal Easy Care Lint Collector
Darks Light Sturdy
16

ABOUT THE DISPENSER DRAWER
The automatic dispenser consists of four compartments
which hold:
•Liquid chlorine bleach.
•Liquid fabric softener.
•Liquid or powdered detergent for prewash.
•Liquid or powdered detergent and color-safe bleach
for main wash.
Liquid Chlorine
8bach
Compartment
Liquid Fabric
Softener
Compartment Liquid
Cup
Detergent
CompaRment
Pre-Wash Detergent Compartment
Add liquid or powdered detergent to this compartment
when using the Pre-Vv'ash option. Always use High-
Efficiency (HE) detergent with your washing machine.
The amount of detergent added for the Pre-VVash
option should be 1/2the amount recommended for the
main "washcycle. Forexample, if the main wash cycle
requires 1/2measure of detergent, add 1/4measure to the
Pre_Washcompartment.
NOTE: When using the Pre-"_/ash option, if using liquid
detergent for t_ main wash, the liquid detergent cup
accessory must be used in the main wash dispenser This
will prevent the main wash liquid detergent from being
dispensed immediately
Main Wash Detergent Compartment
This compartment holds laundry detergent for the main
wash cycle. The detergent is added to the load at the
beginning of the cycle. Always use High-Efficiency (HE)
detergent with your washing machine. Either powdered
or liquid detergent may be used.
Never exceed the manufacturer's recommendations
when adding detergent. Using too much detergent can
result in detergent buildup in clothing and the washer.
NOTE: Liquid or powdered color-safe bleach may be
added to the main wash compartment with detergent of
the same type. DO NOT add liquid or powdered
color-safe bleach to the bleach dispenser. DO NOT mix
liquid and powdered cleaning agents within the same
compartment.
Main Wash Detergent
Compartment
Liquid Bleach Compartment
This compartment holds liquid chlorine bleach, which is
dispensed automatically at the proper time during the
wash cycle.
•Do not add powdered or liquid color-safe bleach to
this compartment. The bleach compartment is designed
to dispense liquid chlorine bleach only. Powdered or
liquid color-safe bleach will not dispense properly.
•Always follow the manufacturer's recommendations
when adding bleach. Do not exceed the maximum fill
line since this can cause the bleach to be dispensed
immediately, causing damage to fabrics. Using too much
bleach can damage fabrics.
•Never pour undiluted liquid chlorine bleach directly
onto the load or into the drum. Fabric damage can occur
Fabric Softener Compartment
This compartment holds liquid fabric softener, which is
automatically dispensed during the final rinse cycle.
Never exceed the manufacturer's recommendations ,when
adding softener. Using too much fabric softenercan result
in buildup in clothing and the washer. Either powdered or
liquid fabric softener may be used.
•Always follow the manufacturer's recommendations
when adding fabric softener. Do not exceed the
maximum flll line. Using too much fabric softener mat/
stain clothes.
•Dilute concentrated fabric softeners ,with -warm water.
Do not exceed the maximum fill line.
•Never pour fabric softener directly onto the load or
into the drum.
17

DETERGENT AND DISPENSER USE
AWord About Detergents
High-Efficiency (HE) detergents produce fewer suds,
dissolve more efficiently to improve washing and rinsing
performance, and help to keep the interior of your
washer clean. Using detergent that is not HE may cause
oversudsing and unsatisfactory performance which
could result in error codes, cycle failure, and
machine damage.
Maximum _-.,_--!
ormal Load Amount_
Liquid Powdered
Detergent Detergent
For proper wash pe_ormance, always measure the
detergent using the measurements provided by the
detergent manufacturer.
The normal amount of HE detergent needed, for average
loads, is less than 1/2of the recommended maximum.
Use less detergent for soft water, light soil or smaller
loads. Never use more than the maximum amount
recommended by the detergent manufacturer.
Detergent Amount
For proper wash performance, always measure the
detergent using the measurements provided by the
detergent manufacturer.
Filling the Dispenser
To add detergent, bleach, and fabric softener to the
automatic dispenser:
Open the dispenser drawer.
OLoad the laundry products into the
appropriate compartments.
O Close the drawer before starting the cycle.
NOTE: It is normal for a small amount of "water to
remain in the bleach and softener compartments at the
end of the cycle.
IMPORTANT: Do not place or store laundry products,
such as detergent, bleach, or liquid fabric softener, on top
of your washer or dryer. Wipe up any spills immediately.
These products can damage the finish and controls.
Designed to use only
High-Efficiency (HE) detergent
IMPORTANT: Your washing machine isdesigned for use
with only High-Efficiency (HE) detergents. HE detergents
are formulated specifically for front-load "washersand
contain suds-reducing agents. Always look for the HE
symbol when purchasing detergent.
IMPORTANT: Not all detergentsare the same. Pay
careful attention to the amount of detergent used to
avoid oversudsing, poor rinsing and detergent buildup in
clothing, and residue buildup that can contribute to odors
inthe machine. NEVER usea cup or scoop other than the
one supplied by the manufacturer of the detergent "you
are using. Never usemore than the maximum amount of
detergent recommended by the manufacturer.
Always measure the detergent amount. While HE
detergents are designed for this type of washing
machine, be careful when measuring the detergent. For
most normal loads, no more than 1/4to 1/2 of cap or
scoop of HE detergent should be used.
NOTE: Extra care must _ exercised when using 2X and
3X concentrated detergents because even a little bit extra
can contribute to the problems mentioned above.
NOTE: Detergents designated as HE compatible may not
provide optimal results.
MAGNETIC DOOR PLUNGER
Safely and conveniently secure the door slightly ajar
with the magnetic door plunger. This will promote air
circulation and allow the interior of the machine to dry.
To use this feature, remove the clean laundry then posi-
tion the door so that the door is almost closed. "When
the magnetic door plunger comes into contact with the
metal washer cabinet, it will secure the door slightly
open, allowing the interior of the "washer to dry.
18

TIME AND STATUS DISPLAY
The time and statusdisplay showsthe estimated time remaining, cycle progress,and door lock status.
O
iWash Tempi iSPinSpeed [ Soil Level ] [ Chime l
A{! Cold R_ns_
O ESTIMATED TIME REMAINING O
V'/hen the START/PAUSE button is pressed, the
washer will automatically detect the load size for
cycles that use load sensing. The control will then
optimize the wash and rinse times, based on the se-
lected cycle, modifiers and options. When the load
size has been determined, the display will change
from dashes (- - -) to the estimated time for that
cycle. For non-load sensing cycles, the estimated
time will display when the cycle is selected.
NOTE:
*The time shown is only an estimate. For example,
the time displayed may pause for a period of time
while the machine is heating the water or balancing
the load. Under certain conditions, the machine can
pause for extended periods of time.
*Estimated time isbased on normal operating
conditions. Several external factors (load size, room
temperature, incoming water temperature, etc.) also
affect the length of estimated time vs. actual time.
LOAD-SENSING INDICATOR
At the beginning of cycles that usethe load sensing
feature, the LOAD SENSING light will blink while the
load size is being measured. Once the size has been
determined, the control adjusts the cycle for
optimum performance. Estimated time remaining will
not display until the load size has been determined,
and may be different for each load.
CYCLESTATUS INDICATOR
These status LEDs illuminate to indicate which
stage of the cycle is currently running, A blinking
light indicates the active stage of the cycle, When
that stage is complete, the light will remain steady.
DOOR LOCK INDICATOR
Indicates that the door is locked. The washer door
will lock while the washer isoperating. The door can
be unlocked by pressing START/PAUSE to pause
the washer,
NOTE:
"If the temperature in the washer istoo high, the
door cannot be unlocked until the washer
has cooled.
•If the water level istoo high, the door will not
unlock. To drain the water, press POWER, then press
the SPIN SPEEDbutton without selecting a cycle.
PressSTART/PAUSE and the water will drain and
the clothes will spin out. Do not try to force the door
open, as it will damage the door.
19

|CYCLE MODIFIER BUTTONS
Each cycle has default settings that are selected
automatically. You may also customize these settings
using the cycle modifier buttons. Pressthe button for the
desired modifier until the indicator light for the desired
value is lit. The washer automatically adjusts the water
level for the type and size of wash load for best results
and maximum efficiency. Due to the high-efficiency
nature of this product, water levels may be much lower
than expected. This isnormal operation and cleaning/
rinsing performance will not be compromised.
NOTE: To protect your garments, not every wash
temperature, spin speed, soil level, or option is available
with every cycle. A chime will sound and the LED will not
light if a selection isnot allowed.
IWashTempl [SpinSpeed] ! SoilLevel I I Chime
OWASH TEMP
"Wash Temp selects the wash and rinse temperature
combination for the selected cycle. Pressthe Wash
Temp button until the indicator light for the desired
setting islit.
"'four washer features a heating element to boost
the hot "water temperature for Extra Hot settings.
This provides improved wash performance at
normal water heater settings.
•Select the water temperature suitable for the type
of load you are washing. Follow the garment fabric
care labels for best results.
•Warm rinsesare regulated at approximately
86°F (30°C),
•_*Varm rinses leave the clothes dryer than
cold rinses, but will result in increased energy
consumption and greater wrinkling of clothes.
•Cold rinses use less energy. The actual rinse
temperature depends on the temperature of the
cold water at the faucet.
O
O
O
SPIN SPEED
Higher spin speeds extract more water from clothes,
reducing drying time and saving energy.
Pressthe SPIN SPEEDbutton until the desired speed
isselected. Some fabrics, suchas delicates, require
a slower spin speed. To protect your clothing, not all
spin speeds are available for all cycles.
The Drain & Spin cycle:
i. Pressthe POWER button to turn ON the washer.
2. Pressthe SPIN SPEEDbutton to select the desired
spin speed. For drain only, select the
NO SPIN option.
3. Pressthe START/PAUSE button. The water will
drain and the clothes will tumble before
the spin routine begins.
SOIL LEVEL
Adjusting the soil level setting will modify the cycle
to allow more time for heavily soiled clothes or less
time for lightly soiled clothes. Pressthe SOIL LEVEL
button until the desired soll level is selected.
CHIME
Pressrepeatedly to adjust the volume of the chime
and keypad tones. You may turn the end-of-cycle
chime and keypad tones ON or OFF with the CHIME
button.
2O