Kenmore 153.336162 User manual

1www.sears.com
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A
C3 Technology®Gas Water Heaters meet
the new ANSI Z21.10.1 standard that deals
with the accidental or unintended ignition
of flammable vapors, such as those
emitted by gasoline.
Owner’s Manual
FORPOTABLE WATER HEATINGONLY.
NOT SUITABLE FOR SPACE HEATING.
NOT FOR USE IN MOBILE HOMES.
MODELNO.
153.336162 30Gallon Short
153.336262 40Gallon Short
153.336362 30Gallon
153.336466 40Gallon
153.336566 50Gallon
153.336762 30Gallon Propane (L.P.)
153.336862 40Gallon Propane (L.P.)
153.336962 50Gallon Propane (L.P.)
For Your Safety
ANODORANTISADDEDTOTHEGASUSEDBYTHISWATERHEATER.
• Safety Instructions
• Installation
• Operation
• Care and Maintenance
• Troubleshooting
• Parts List
POWER MISER™ 6
GAS WATER HEATER
Sinopuede leero entenderelinglésynecesitael manualinstructivo
y/o etiquetas en español puede obtenerlos llamando al
1-800-821-2017. NO TRATE DE INSTALAR O OPERAR ESTE
CALENTADORDEAGUAsinoentiendelainformaciónenlasetiquetas
oenelmanual instructivo.Nohacercasode estaadvertencia podría
resultarenlaMUERTEOGRAVESLESIONESCORPORALES.
ADVERTENCIA
PRINTED IN THE U.S.A 0705 PART NO. 184231-001

2
SAFE INSTALLATION, USE AND SERVICE
Your safety and the safety of others is extremely important in the installation, use and servicing of this water heater.
Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and
others of a potential injury hazard. Read and obey all safety messages and instructions throughout this manual. It is very
important that the meaning of each safety message is understood by you and others who install, use or service this water heater.
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
All safety messages will generally tell you about the type of hazard, what can happen if you do not follow the safety message and
how to avoid the risk of injury.
IMPORTANT DEFINITIONS
•Gas Supplier: The natural gas or propane utility or service who supplies gas for utilization by the gas burning
applianceswithin thisapplication. Thegas suppliertypically hasresponsibility forthe inspectionand codeapproval of
gas piping up to and including the natural gas meter or propane storage tank of a building. Many gas suppliers also
offerservice andinspection of appliances within the building.
DANGER
WARNING
CAUTION
DANGER indicates an imminently
hazardous situation which, if not avoided,
could result in death or injury.
WARNINGindicates a potentiallyhazardous
situation which, if not avoided, could result
in death or injury.
CAUTION indicatesa potentiallyhazardous
situation which, if not avoided, may result
in minor or moderate injury.
CAUTION used without the safety alert
symbol indicates a potentially hazardous
situation which, if not avoided, could result
in property damage.
CAUTION
© Sears, Roebuck and Co.

3
SAFETY PRECAUTIONS

4
TABLE OF CONTENTS
SAFEINSTALLATION, USEAND SERVICE ................................................................................................. 2
SAFETYPRECAUTIONS.............................................................................................................................. 3
TABLE OF CONTENTS ................................................................................................................................ 4
CUSTOMERRESPONSIBILITIES ................................................................................................................ 5
PRODUCT SPECIFICATIONS...................................................................................................................... 5
MATERIALS AND BASIC TOOLS NEEDED ................................................................................................. 6
MaterialNeeded ...................................................................................................................................................... 6
Basic Tools ............................................................................................................................................................. 6
TYPICALINSTALLATION............................................................................................................................... 7
INSTALLATIONINSTRUCTIONS...............................................................................................................8-16
RemovingtheOldWater Heater .............................................................................................................................. 8
Facts to Consider About the Location ................................................................................................................ 9-10
InsulationJackets ................................................................................................................................................. 10
CombustionAir and VentilationAppliances
inUnconfinedSpaces............................................................................................................................................ 10
CombustionAir and VentilationAppliances
inConfinedSpaces ...........................................................................................................................................11-12
WaterPiping .................................................................................................................................................... 12-13
TemperaturePressure Relief Valve.................................................................................................................... 13-14
Fillingthe Water Heater......................................................................................................................................... 14
Venting............................................................................................................................................................. 14-15
GasPiping ....................................................................................................................................................... 15-16
SedimentTrap.................................................................................................................................................. 16-17
OPERATING INSTRUCTIONS ................................................................................................................ 18-19
Lighting&Operating Label .................................................................................................................................... 18
TemperatureRegulation ......................................................................................................................................... 19
SERVICEANDADJUSTMENT ............................................................................................................... 20-22
Tank(Sediment) Cleaning...................................................................................................................................... 20
Venting System Inspection.................................................................................................................................... 20
BurnerInspection .................................................................................................................................................. 20
BurnerCleaning..................................................................................................................................................... 20
Housekeeping .................................................................................................................................................. 20-21
AnodeRodInspection ........................................................................................................................................... 21
Temperature-PressureReliefValveOperation ........................................................................................................ 21
Draining............................................................................................................................................................ 21-22
DrainValve WasherReplacement.......................................................................................................................... 22
Service .................................................................................................................................................................. 22
TROUBLESHOOTINGGUIDE ................................................................................................................ 23-26
Start Up Conditions .............................................................................................................................................................23-25
ThermalExpansion........................................................................................................................................... 23
StrangeSounds ............................................................................................................................................... 23
DraftHoodOperation................................................................................................................................... 23-24
Condensation ................................................................................................................................................... 24
Smoke/Odor..................................................................................................................................................... 24
OperationalConditions ..................................................................................................................................... 24-25
SmellyOdor ..................................................................................................................................................... 24
Air in Hot Water Faucets.................................................................................................................................. 25
HighTemperatureShut-OffSystem .................................................................................................................. 24
LeakageCheckpoints....................................................................................................................................... 25
TroubleshootingItems ........................................................................................................................................... 26
NOTES.................................................................................................................................................... 27-28
PARTS ORDER LIST .............................................................................................................................29-31
WARRANTY ................................................................................................................................................ 32

5
Thank You for purchasing a Kenmore water heater. Properly
installed and maintained, it should give you years of trouble
free service. If you should decide that you want the new water
heaterprofessionallyinstalled bySearscall 1-800-4-MY-HOME®.
They will arrange for prompt, quality installation by Sears
authorized contractors.
AbbreviationsFoundIn ThisInstruction Manual:
• CSA - Canadian Standards Association
• ANSI - American National Standards Institute
• NFPA - National Fire Protection Association
• ASME - American Society of Mechanical Engineers
• GAMA - Gas Appliance Manufacturers Association
• This gas-fired water heater is design certified by CSA
INTERNATIONAL under American National Standard/CSA
Standard for Gas Water Heaters ANSI Z21.10.1 • CSA 4.1
(current edition).
• Read the “Safety Precautions” section, page 3 of this manual
first and then the entire manual carefully. If you don’t follow
the safety rules, the water heater will not operate properly. It
could cause DEATH, SERIOUS BODILY INJURY AND/OR
PROPERTYDAMAGE.
This manual contains instructions for the installation,
operation, and maintenance of the gas-fired water heater. It
also contains warnings through out the manual that you must
read and be aware of. All warnings and all instructions are
essential to the proper operation of the water heater and
your safety. Since we cannot put everything on the first few
pages,READ THEENTIREMANUALBEFOREATTEMPTING
TOINSTALLOROPERATETHEWATERHEATER.
• The installation must conform with these instructions and
the local code authority having jurisdiction. In the absence of
local codes, installations shall comply with the following:
In the United States: The National Fuel Gas Code ANSI
Z223.1/NFPA 54. This publication is available from the
Canadian StandardsAssociation, 8501 East Pleasant Valley
Rd, Cleveland Ohio 44131, or The National Fire Protection
Association, 1 Batterymarch Park, Quincy, MA 02269.
• If after reading this manual you have any questions or do not
understand any portion of the instructions, call the Sears
Service Center.
• Carefully plan the place where you are going to put the water
heater. Correct combustion, vent action, and vent pipe
installation are very important in preventing death from
possible carbon monoxide poisoning and fires. See
figure 1.
Examine the location to ensure the water heater complies
with the Facts to Consider About the Location section in this
manual.
• For California installation this water heater must be braced,
anchored, or strapped to avoid falling or moving during an
earthquake. See instructions for correct installation
procedures. Instructions may be obtained from your local
dealer, wholesaler, public utilities or California Office of the
State Architect, 400 P Street, Sacramento, CA 95814.
• Massachusetts Code requires this water heater to be
installed in accordance with Massachusetts 248-CMR 2.00:
State Plumbing Code and 248-CMR 5.00.
• Complies with SCAQMD rule #1121 and districts having
equivalent NOx requirements.
CUSTOMER RESPONSIBILITIES
PRODUCT SPECIFICATIONS
RECOVERYRECOVERY
RECOVERYRECOVERY
RECOVERY MINIMUMMINIMUM
MINIMUMMINIMUM
MINIMUM DIMENSIONSDIMENSIONS
DIMENSIONSDIMENSIONS
DIMENSIONS
TT
TT
TANKANK
ANKANK
ANK TYPETYPE
TYPETYPE
TYPE INPUTINPUT
INPUTINPUT
INPUT RARA
RARA
RATE GTE G
TE GTE G
TE GALAL
ALAL
ALSS
SS
S..
..
.VENT PIPEVENT PIPE
VENT PIPEVENT PIPE
VENT PIPE DIAMETERDIAMETER
DIAMETERDIAMETER
DIAMETER IN INCHES (mm)IN INCHES (mm)
IN INCHES (mm)IN INCHES (mm)
IN INCHES (mm)
MODELMODEL
MODELMODEL
MODEL CAPCAP
CAPCAP
CAPAA
AA
ACITYCITY
CITYCITY
CITY OFOF
OFOF
OF RARA
RARA
RATETE
TETE
TE PER HOURPER HOUR
PER HOURPER HOUR
PER HOUR INCHESINCHES
INCHESINCHES
INCHES INCHESINCHES
INCHESINCHES
INCHES HEIGHT TOHEIGHT TO
HEIGHT TOHEIGHT TO
HEIGHT TO
NUMBERNUMBER
NUMBERNUMBER
NUMBER IN GIN G
IN GIN G
IN GALAL
ALAL
ALS (LS (L
S (LS (L
S (LTRS)TRS)
TRS)TRS)
TRS) GASGAS
GASGAS
GAS (Btu/hr)(Btu/hr)
(Btu/hr)(Btu/hr)
(Btu/hr) @ 90°F RISE@ 90°F RISE
@ 90°F RISE@ 90°F RISE
@ 90°F RISE (mm)(mm)
(mm)(mm)
(mm) (mm)(mm)
(mm)(mm)
(mm) JACKET TOJACKET TO
JACKET TOJACKET TO
JACKET TOP
153.336162 30 (114) NATURAL 32,000 30.6 3" (76) or 4" (102) 181/2" (470) 433/4" (1,111)
153.336262 40 (151) NATURAL 35,500 35.4 3" (76) or 4" (102) 20"(508) 47 1/4"(1,200)
153.336362 30 (114) NATURAL 35,500 34.9 3” (76) 16”(406) 57 1/2”(1,461)
153.336466 40 (151) NATURAL 35,500 35.4 3" (76) 181/2" (470) 551/2" (1,410)
153.336566 50 (189) NATURAL 35,500 35.4 3" (76) 20"(508) 56 1/2”(1,435)
153.336762 30 (114) PROPANE 35,500 34.9 3" (76) 16" (406) 571/2” (1,461)
153.336862 40 (151) PROPANE 35,500 35.4 3" (76) 181/2" (470) 551/2”(1,410)
153.336962 50 (189) PROPANE 35,500 35.4 3" (76) 20"(508) 56 1/2”(1,435)

6
MATERIALS AND BASIC TOOLS NEEDED
Materials Needed
To simplify the installation Sears has available the installation parts shown below. You may or may not need all of these materials,
depending on your type of installation.
WATER HEATER INSTALLATION KIT WITH
FLEXIBLE CONNECTORS FOR 3/4”
(19.05 mm) OR 1/2” (12.7 mm) THREADED OR
COPPER PLUMBING AND FLEXIBLE WATER
HEATER GAS CONNECTOR WITH FITTINGS.
EXPANSIONTANKS FOR
THERMALEXPANSION
CONDITIONSAVAILABLE
IN 2 GALLONS
(7.6 LITERS) AND
5 GALLONS (18.9 LITERS)
CAPACITYHROUGH
LOCAL SEARS STORE OR
SERVICE CENTER.
DRAINPANSAVAILABLEIN 20”
(508 mm) DIAMETER FOR
WATER HEATERSHAVINGA
DIAMETER 18” (457 mm) OR
LESS, 24” (610mm) DIAMETER
FOR WATER HEATERSHAVING
A DIAMETER 22” (559 mm) OR
LESSANDAVAILABLE IN 28”
(711 mm) DIAMETER FOR
WATER HEATERSHAVINGA
DIAMETER 26” (660 mm) OR
LESS.
Basic Tools
You may or may not need all these tools, depending on your
type of installation. These tools can be purchased at your local
Sears Store.
• Pipe Wrenches (2) 14” (356 mm)
• Screwdriver
• Tin Snips
• 6’ (1.82 m) Tape or Folding Ruler
• Garden Hose
• Drill
• Pipe Dope or Teflon Tape
Additional Tools Needed
When Sweat Soldering
• Tubing Cutters or Hacksaw
• Propane Tank
• Soft Solder
• Solder Flux
• Emery Cloth
• Wire Brushes
SLOT-HEAD SCREWDRIVER
PHILLIPS SCREWDRIVER TIN SNIPS
PIPE WRENCH
PIPE DOPE
(SQUEEZE TUBE)
USE FOR WATER AND GAS
CONNECTIONS
DRILL
GARDENHOSE 6 FOOT TAPE
ROLL OF TEFLON
TAPE (USEONLY ON
WATER CONNECTIONS)
HACKSAW
3/4” (19 mm) WIRE BRUSH
1/2” (13 mm) WIRE BRUSH SOLDER FLUX
ROLL OF LEAD-FREE
SOFT SOLDER
TUBING CUTTER PROPANE TORCH
ROLL OF
EMERYCLOTH

7
TYPICAL INSTALLATION
GET TO KNOW YOUR WATER HEATER - GAS MODELS
A Vent Pipe
B Draft Hood
C Anode
D Hot Water Outlet
E Outlet
F Flexible Water Connections
G Gas Supply
H Manual Gas Shut-off Valve
I Ground Joint Union
* INSTALLINACCORDANCE
WITH LOCAL CODES.
* DRIP LEG AS REQUIRED
BY LOCAL CODES.
FIGURE1.
J Drip Leg (Sediment Trap)
K Inner Door
L Outer door
M Union
N Inlet Water Shut-off Valve
O Cold Water Inlet
P Inlet Dip Tube
Q Temperature-Pressure Relief Valve
R Rating Plate
S Flue Baffle
T Thermostat
U Drain Valve
V Pilot and Main Burner
W Flue
X Drain Pan
Y Thermostat Shield (optional)
Z Piezo Igniter
AA Air Intake Screen
(V) PILOT & MAIN BURNER
(T) THERMOSTAT
* ALL PIPING MATERIALS TO BE
SUPPLIED BY CUSTOMERS.
TO VENT TERMINATION
ON ROOF
THERMOSTAT
COVER
(OPTIONAL)
Y

8
INSTALLATION INSTRUCTIONS
1. Turn “OFF” the gas supply to the
water heater.
If the main gas line Shut-off valve
serving all gas appliances is
used, also shut “OFF” the gas at
each appliance. Leave all gas
appliances shut “OFF” until the
water heater installation is
completed, see Figures 2 and 3.
2. Turn “OFF” the water supply to the
water heater at the water shut off
valve or water meter. Some
installations require that the water
be turned off to the entire house,
see Figures 2 and 4.
FIGURE2.
Removing the Old Water Heater
FIGURE3.
FIGURE4.
3. Check again to make sure the gas supply is “OFF” to the
water heater. Then disconnect the gas supply connection
from the gas control valve.
4. Attach a hose to the water heater
drain valve and put the other end
in a floor drain or outdoors. Open
thewaterheaterdrain valve. Open
anearbyhot waterfaucetwhich will
relieve pressure in the water
heater and speed draining. The
waterpassingout of thedrainvalve
may be extremely hot. To avoid
being scalded, make sure all
connections are tight and that the
water flow is directed away from
any person, see Figures 2 and 5. FIGURE5.
5. Disconnectthevent pipe fromthedraft hoodwhereitconnects
to the water heater. In most installations the vent pipe can
be lifted off after any screw or other attached devices are
removed. Dispose of the draft hood. The new water heater
has a draft hood which must be used for proper operation.
6. If you have copper piping to the water heater, the two copper
water pipes can be cut with a hacksaw approximately four
inches away from where they connect to the water heater,
see Figure 6. This will avoid cutting off pipes too short.
Additional cuts can be made later if necessary. Disconnect
the temperature-pressure relief valve drain line. When the
water heater is drained, disconnect the hose from the drain
valve. Close the drain valve. The water heater is now
completely disconnected and ready to be removed.
FIGURE6.
If you have galvanized pipes to the water heater, loosen the
two galvanized pipes with a pipe wrench at the union in each
line. Alsodisconnectthepiping remaining tothewater heater,
see Figure 7. These pieces should be saved since they may
be needed when reconnecting the new water heater.
Disconnect the temperature-pressure relief valve drain line.
When the water heater is drained, disconnect the hose from
the drain valve. Close the drain valve. The water heater is
now completely disconnected and ready to be removed.
Mineral buildup or sediment may have accumulated in the
old water heater. This causes the water heater to be much
heavier than normal and this residue, if spilled out, could
cause staining.
FIGURE7.

9
• Devices that will turn off the gas supply to a gas water heater
while at the same time shutting off its water supply.
INSTALLATIONS INAREAS WHERE FLAMMABLE LIQUIDS
(VAPORS) ARE LIKELY TO BE PRESENT OR STORED
(GARAGES, STORAGE AND UTILITY AREAS, ETC.):
Flammable liquids (such as gasoline, solvents, propane [LP or
butane, etc.] and other substances such as adhesives, etc.)
emit flammable vapors which can be ignited by a gas water
heater’s pilot light or main burner. The resulting flashback and
fire can cause death or serious burns to anyone in the area.
Even though this water heater is a flammable vapors ignition
resistant water heater and is designed to reduce the chances
of flammable vapors being ignited, gasoline and other
flammable substances should never be stored or used in the
same vicinity or area containing a gas water heater or other
open flame or spark producing appliance.
Also, the water heater must be located and/or protected so it is
not subject to physical damage by a moving vehicle.
This water heater must not be installed directly on carpeting.
Carpeting must be protected by metal or wood panel beneath
the appliance extending beyond the full width and depth of the
appliance by at least 3 inches (76.2 mm) in any direction, or if
the appliance is installed in an alcove or closet, the entire floor
must be covered by the panel. Failure to heed this warning may
result in a fire hazard.
Facts to Consider About
the Location
Carefully choose an indoor location for the new water heater,
because the placement is a very important consideration for
the safety of the occupants in the building and for the most
economical use of the appliance. This water heater is not for
use in manufactured (mobile) homes or outdoor installation.
Whetherreplacingan old waterheateror putting thewaterheater
in a new location, the following critical points must be observed:
• Select a location indoors as close as practical to the gas
vent or chimney to which the water heater vent is going to be
connected, and as centralized with the water piping system
as possible.
• Selected location must provide adequate clearances for
servicing and proper operation of the water heater.
Installation of the water heater must be accomplished in such a
manner that if the tank or any connections should leak, the flow
will not cause damage to the structure. For this reason, it is not
advisable to install the water heater in an attic or upper floor.
When such locations cannot be avoided, a suitable drain pan
should be installed under the water heater. Drain pans are
available at your local Sears or hardware store. Such a drain
pan must have a minimum length and width of at least 2 inches
(51 mm) greater that the water heater dimensions and must be
piped to an adequate drain. The pan must not restrict
combustion air flow.
Water heater life depends upon water quality, water pressure
and the environment in which the water heater is installed.
Water heaters are sometimes installed in locations where
leakage may result in property damage, even with the use of a
drain pan piped to a drain. However, unanticipated damage
can be reduced or prevented by a leak detector or water shut-
off device used in conjunction with a piped drain pan. These
devices are available from some plumbing supply wholesalers
and retailers, and detect and react to leakage in various ways:
• Sensors mounted in the drain pan that trigger an alarm or turn
off the incoming water to the water heater when leakage is
detected.
• Sensors mounted in the drain pan that turn off the water supply
to the entire home when water is detected in the drain pan.
• Water supply shut-off devices that activate based on the water
pressure differential between the cold water and hot water
pipes connected to the water heater.

10
Minimum clearances between the water heater and combustible
construction are 0 inch at the sides and rear,
4 inches (102 mm) at the front, and 6 inches (153 mm) from the
vent pipe, see Figure 8. Clearance from the top of the jacket is 12
inches (305 mm) on most models. Note that a lesser dimension
may be allowed on some models, refer to the label attached
adjacent to the gas control valve on the water heater.
FIGURE8.
A gas water heater cannot operate properly without the correct
amount of air for combustion, see Figure 9. Do not install in a
confined area such as a closet, unless you provide air as shown
in the Locating The New Water Heater section. Never obstruct
the flow of ventilation air. If you have any doubts or questions at
all, call your gas supplier. Failure to provide the proper amount
of combustion air can result in a fire or explosion and cause
death, serious bodily injury, or property damage.
FIGURE9.
If this water heater will be used in beauty shops, barber shops,
cleaning establishments, or self-service laundries with dry
cleaning equipment, it is imperative that the water heater or
water heaters be installed so that combustion and ventilation
air be taken directly from outdoors (direct vent).
Propellants of aerosol sprays and volatile compounds,
(cleaners, chlorine based chemicals, refrigerants, etc.) in
addition to being highly flammable in many cases, will also
change to corrosive hydrochloric acid when exposed to the
combustion products of the water heater. The results can be
hazardous, and also cause product failure.
Insulation Blankets
Insulation blankets available to the general public for external
use on gas water heaters are not necessary with Kenmore
products. The purpose of an insulation blanket is to reduce the
standby heat loss encountered with storage tank heaters. Your
Kenmorewaterheatermeetsorexceeds the NationalAppliance
Energy Conservation Act standards with respect to insulation
and standby loss requirements, making an insulation blanket
unnecessary.
WARNING
Should you choose to apply an insulation blanket to this heater,
you should follow these instructions (See Figure 1 for
identification of components mentioned below). Failure to follow
these instructions can restrict the air flow required for proper
combustion, potentially resulting in fire, asphyxiation, serious
personal injury or death.

11
•Do not apply insulation to the top of the water heater, as this
will interfere with safe operation of the draft hood.
•Do not cover the outer door, thermostat or temperature &
pressure relief valve.
•Do not allow insulation to come within 2” (50.8 mm) of the
floortopreventblockage of combustion airflowtothe burner.
•Do not cover the instruction manual. Keep it on the side of
the water heater or nearby for future reference.
•Do obtain new warning and instruction labels from Sears
for placement on the blanket directly over the existing labels.
•Do inspect the insulation blanket frequently to make certain
it does not sag, thereby obstructing combustion air flow.
CombustionAir and Ventilation for
Appliances Located in Unconfined Spaces
UNCONFINED SPACE is space whose volume is not less than
50 cubic feet per 1,000 Btu per hour (4.8 m3per kW) of the
aggregate input rating of all appliances installed in that space.
Rooms communicating directly with the space in which the
appliances are installed, through openings not furnished with
doors, are considered a part of the unconfined space.
In unconfined spaces in buildings, infiltration may be adequate
to provide air for combustion, ventilation and dilution of flue
gases. However, in buildings of tight construction (for example,
weatherstripping,heavily insulated, caulked,vaporbarrier, etc.),
additional air may need to be provided using the methods
described in Combustion Air and Ventilation for Appliances
Located in Confined Spaces.
CombustionAir and Ventilation for
Appliances Located in Confined Spaces
CONFINED SPACE is a space whose volume is less than
50 cubic feet per 1,000 Btu per hour (4.8 m3per kW) of the
aggregate input rating of all appliances installed in that space.
A. ALLAIR FROMINSIDEBUILDINGS:
(See Figure 9 on page 9 and Figure 10 below)
The confined space shall be provided with two permanent
openings communicating directly with an additional room(s)
of sufficient volume so that the combined volume of all spaces
meets the criteria for an unconfined space. The total input of
all gas utilization equipment installed in the combined space
shall be considered in making this determination. Each
opening shall have a minimum free area of one square inch
per 1,000 Btu per hour (22 cm2/kW) of the total input rating of all
gas utilization equipment in the confined space, but not less
than 100 square inches (645 cm2). One opening shall
commence within 12 inches (30 cm) of the top and one
commencing within 12 inches (30 cm) of the bottom of the
enclosures.
FIGURE10.
B.ALLAIR FROM OUTDOORS: (See Figures 9, 11,12 and 13)
The confined space shall be provided with two permanent
openings, one commencing within 12 inches (30 cm) of the
top and one commencing within 12 inches (30 cm) from the
bottom of the enclosure. The openings shall communicate
directly, or by ducts, with the outdoors or spaces (crawl or attic)
that freely communicate with the outdoors.
FIGURE11.
• When directly communicating with the outdoors, each opening
shall have a minimum free area of 1 square inch per 4,000 Btu
per hour (5.5 cm2/kW) of total input rating of all equipment in the
enclosure, see Figure 12.
• When communicating with the outdoors through vertical
ducts, each opening shall have a minimum free area of
1 square inch per 4,000 BTU per hour (5.5 cm2/kW) of total
input rating of all equipment in the enclosure, see
Figure 12.

12
FIGURE12.
• When communicating with the outdoors through horizontal
ducts, each opening shall have a minimum free area of 1
square inch per 2,000 BTU per hour (11 cm2/kW) of total
input rating of all equipment in the enclosure, see
Figure 13.
• When ducts are used, they shall be of the same cross-
sectional area as the free area of the openings to which
they connect. The minimum short side dimension of
rectangular air ducts shall not be less than 3 inches
(76.2 mm), see Figure 13.
FIGURE13.
• Louvers and Grilles: In calculating free area, consideration
shall be given to the blocking effect of louvers, grilles or
screens protecting openings. Screens used shall not be
smallerthan1/4inch (6.4 mm) mesh. Ifthefree area through
a design of louver or grille is known, it should be used in
calculating the size opening required to provide the free
area specified. If the design and free area is not known, it
may be assumed that wood louvers will be 20-25 percent
free area and metal louvers and grilles will have 60-75
percent free area. Louvers and grilles shall be fixed in the
open position or interlocked with the equipment so that they
are opened automatically during equipment operation.
• Special Conditions Created by Mechanical Exhausting or
Fireplaces: operation of exhaust fans, ventilation systems,
clothes dryers or fireplaces may create conditions requiring
specialattentiontoavoid unsatisfactory operationofinstalled
gas utilization equipment.
Water Piping
HOTTERWATER CAN SCALD:
Waterheatersareintended toproducehotwater. Waterheated
to a temperature which will satisfy space heating, clothes
washing, dish washing, cleaning and other sanitizing needs
can scald and permanently injure you upon contact. Some
people are more likely to be permanently injured by hot water
than others. These include the elderly, children, the infirm, or
physically/mentallyhandicapped. Ifanyone usinghotwater in
your home fits into one of these groups or if there is a local
code or state law requiring a certain temperature water at the
hot water tap, then you must take special precautions. In
addition to using the lowest possible temperature setting that
satisfies your hot water needs, a means such as a *mixing
valve,shallbeusedat thehotwatertapsused bythesepeople
oratthe water heater.Mixingvalves areavailableatplumbing
supply or hardware stores, see Figure 14 below. Valves for
reducingpoint ofusetemperaturebymixingcoldand hotwater
are also available. Follow manufacturer’s instructions for
installation of the valves. Before changing the factory setting
onthethermostat, readtheTemperature Regulation sectionin
this manual.
FIGURE14.

13
Thiswaterheater shall not beconnectedto any heatingsystems
or component(s) used with a non-potable water heating
appliance.
All piping components connected to this unit for space heating
applications shall be suitable for use with potable water.
Toxic chemicals, such as those used for boiler treatment shall
not be introduced into this system.
Water supply systems may, because of such events as high
line pressure, frequent cut-offs or the effects of water hammer
among others, have installed devices such as pressure
reducing valves, check valves, back flow preventers, etc. to
control these types of problems. When these devices are not
equipped with an internal by-pass, and no other measures are
taken, the devices cause the water system to be closed. As
water is heated, it expands (thermal expansion) and closed
systems do not allow for the expansion of heated water.
The water within the water heater tank expands as it is heated
and increases the pressure of the water system. If the relieving
point of the water heater’s temperature-pressure relief valve is
reached, the valve will relieve the excess pressure. The
temperature-pressure relief valve is not intended for the
constant relief of thermal expansion. This is anunacceptable
condition and must be corrected. It is recommended that any
devices installed which could create a closed system have a
by-pass and/or the system have an expansion tank to relieve
the pressure built by thermal expansion in the water system.
Refer to the Thermal Expansion section under Troubleshooting
Guide or contact local plumbing authority or local Sears Service
Center on how to control this situation.
NOTE:To protect against untimely corrosion of hot and cold
water fittings, it is strongly recommended that di-electric
unions or couplings be installed on this water heater when
connected to copper pipe.
Figure 15 shows the typical attachment of the water piping to
the water heater. The water heater is equipped with 3/4” NPT
water connections.
NOTE: If using copper tubing, solder tubing to an adapter
before attaching the adapter to the cold water inlet
connection. Do not solder the cold water supply line directly
to the cold water inlet. It will harm the dip tube and damage
the tank.
• Look at the top cover of the water heater. The water outlet is
marked “HOT”. Put two or three turns of teflon tape around
the threaded end of the threaded-to-sweat coupling and
around both ends of the 3/4” NPT threaded nipple. Using
flexible connectors, connect the hot water pipe to the hot
water outlet on the water heater.
• Look at the top of the water heater. The cold water inlet is
marked “COLD”. Put two or three turns of teflon tape around
the threaded end of the threaded-to-sweat coupling and
around both ends of the 3/4” NPT threaded nipple. Using
flexible connectors, connect the cold water pipe to the cold
water inlet of the water heater.
NOTE: This water heater is super insulated to minimize
heat loss from the tank. Further reduction in heat loss
can be accomplished by insulating the hot water lines
from the water heater.
INSTALLATIONCOMPLETEDUSING
INSTALLATION KIT
FIGURE15.
T & P Valve and Pipe Insulation
Remove insulation for T & P valve and pipe connections from
carton.
FIGURE15A.
Fit pipe insulation over the incoming cold water line and the hot
water line. Make sure that the insulation is against the top
cover of the heater.

14
FitT&Pvalve insulationovervalve. Makesurethat theinsulation
does not interfere with the lever of the T & P valve.
Secure all insulation using tape.
Temperature-Pressure Relief Valve
This heater is provided with a properly certified combination
temperature - pressure relief valve by the manufacturer.
The valve is certified by a nationally recognized testing
laboratory that maintains periodic inspection of production of
listed equipment as meeting the requirements for Relief Valves
and Automatic Gas Shut-off Devices for Hot Water Supply
Systems, ANSI Z21.22 and the code requirements of ASME.
If replaced, the valve must meet the requirements of local
codes, but not less than a combination temperature and
pressure relief valve certified as indicated in the above
paragraph.
The valve must be marked with a maximum set pressure not to
exceed the marked hydrostatic working pressure of the water
heater (150 psi = 1,035kPa) and a discharge capacity not less
than the water heater input rate as shown on the model rating
plate.
For safe operation of the water heater, the relief valve must not
be removed from its designated opening nor plugged.
The temperature-pressure relief valve must be installed directly
into the fitting of the water heater designed for the relief valve.
Position the valve downward and provide tubing so that any
discharge will exit only within 6 inches (153 mm) above, or at
anydistance belowthestructural floor, seeFigure16. Be certain
that no contact is made with any live electrical part. The
discharge opening must not be blocked or reduced in size
under any circumstances. Excessive length, over 30 feet
(9.14 m), or use of more than four elbows can cause restriction
and reduce the discharge capacity of the valve.
No valve or other obstruction is to be placed between the relief
valve and the tank. Do not connect tubing directly to discharge
drain unless a 6 inch air gap is provided. To prevent bodily
injury, hazard to life, or property damage, the relief valve must
be allowed to discharge water in quantities should
circumstances demand. If the discharge pipe is not connected
to a drain or other suitable means, the water flow may cause
property damage.
FIGURE16.
The Discharge Pipe:
• Shall not be smaller in size than the outlet pipe size of the
valve, or have any reducing couplings or other restrictions.
• Shall not be plugged or blocked.
• Shall be of material listed for hot water distribution.
• Shall be installed so as to allow complete drainage of both
the temperature-pressure relief valve, and the discharge
pipe.
• Shall terminate at an adequate drain.
• Shall not have any valve between the relief valve and tank.

15
The temperature-pressure relief valve must be manually
operated at least once a year. Caution should be taken to
ensure that (1) no one is in front of or around the outlet of the
temperature-pressure relief valve discharge line, and (2) the
water manually discharged will not cause any bodily injury or
property damage because the water may be extremely hot.
If after manually operating the valve, it fails to completely reset
and continues to release water, immediately close the cold
water inlet to the water heater, follow the draining instructions,
and replace the temperature-pressure relief valve with a new
one.
Filling the Water Heater
Never use this water heater unless it is completely full of water.
To prevent damage to the tank, the tank must be filled with
water. Water must flow from the hot water faucet before turning
“ON” gas to the water heater.
To fill the water heater with water:
• Close the water heater drain valve by turning the handle to
the right (clockwise). The drain valve is on the lower front of
the water heater.
• Open the cold water supply valve to the water heater.
NOTE:The coldwater supplyvalve mustbeleftopenwhen
the water heater is in use.
• To insure complete filling of the tank, allow air to exit by
opening the nearest hot water faucet. Allow water to run
until a constant flow is obtained. This will let air out of the
water heater and the piping.
• Check all water piping and connections for leaks. Repair
as needed.
Venting
VENT DAMPERS - Any vent damper, whether it is operated
thermally or otherwise must be removed if its use inhibits proper
drafting of the water heater.
Thermally Operated Vent Dampers: Gas-fired water heaters
having thermal efficiency in excess of 80% may produce a
relatively low flue gas temperature. Such temperatures may
not be high enough to properly open thermally operated vent
dampers. This would cause spillage of the flue gases and
may cause carbon monoxide poisoning.
Vent dampers must bear evidence of certification as complying
with the current edition of the American National Standard
ANSI Z21.68 (ANSI Z21.66 & 67, respectively, cover electrically
and mechanically actuated vent dampers). Before installation
of any vent damper, consult your local Sears Service Center or
the local gas supplier for further information.
To insure proper venting of this gas-fired water heater, the
correct vent pipe diameter must be utilized. Any additions or
deletions of other gas appliances on a common vent with this
water heater may adversely affect the operation of the water
heater. Consult your gas supplier if any such changes are
planned. For replacement heater installations where using pre-
existing venting, venting must be inspected for obstructions
and if deterioration is present, venting must be replaced.
For proper venting in certain installations, a larger diameter
vent pipe may be necessary. Consult your local Sears Service
Center or gas supplier to aid you in determining the proper
venting for your water heater from the vent tables in the current
edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54.
Periodically check the venting system for signs of obstruction
or deterioration and replace if needed.
The combustion and ventilation air flow must not be obstructed.
The water heater with draft hood installed must be connected
to a chimney or listed vent pipe system, which terminates to
theoutdoors. Neveroperatethewater heater unless it isvented
to the outdoors and has adequate air supply to avoid risks of
improper operation, explosion or asphyxiation.
• For proper draft hood attachment, the draft hood legs may
be angled slightly inward.
• Place the draft hood legs in the receiving holes on the top of
the water heater. The legs will snap in the holes to give a
tight fit. Secure two legs to top with sheet metal screws.
• Place the vent pipe over the draft hood. With the vent pipe in
position, drill a small hole through both the vent pipe and
draft hood. Secure them together with a sheet metal screw,
see Figure 17.
Obstructed or deteriorated vent systems may present serious
health risk or asphyxiation.

16
FIGURE17.
The vent pipe from the water heater must be no less than the
diameter of the draft hood outlet on the water heater and must
slope upward at least 1/4 inch per linear foot (21 mm per meter),
see Figure 18.
FIGURE18.
All vent gases must be completely vented to the outdoors of the
structure (dwelling). Install only the draft hood provided with
the new water heater and no other draft hood.
Vent pipes must be secured at each joint with sheet metal
screws.
There must be a minimum of 6 inches (153 mm) clearance
between single wall vent pipe and any combustible material.
Fill and seal any clearance between single wall vent pipe and
combustible material with mortar mix, cement, or other
noncombustible substance. For other than single wall, follow
vent pipe manufacturer’s clearance specifications. To insure
a tight fit of the vent pipe in a brick chimney, seal around the
vent pipe with mortar mix cement.
Failure to have required clearances between vent piping and
combustible material will result in a fire hazard.
Be sure vent pipe is properly connected to prevent escape of
dangerous flue gases which could cause deadly asphyxiation.
Chemical vapor corrosion of the flue and vent system may
occur if air for combustion contains certain chemical vapors.
Spray can propellants, cleaning solvents, refrigerator and air
conditioner refrigerants, swimming pool chemicals, calcium
and sodium chloride, waxes, bleach and process chemicals
are typical compounds which are potentially corrosive.
Gas Piping
Make sure the gas supplied is the same type listed on the
model rating plate. The inlet gas pressure must not exceed
14 inch water column (3.5kPa) for natural and propane gas
(L.P.). The minimum inlet gas pressure listed on the rating
plate is for the purpose of input adjustment. If the gas control
valve is subjected to pressures exceeding 1/2 pound per square
inch (3.5kPa), the damage to the gas control valve could result
in a fire or explosion from leaking gas.
If the main gas line shut-off serving all gas appliances is used,
also turn “OFF” the gas at each appliance. Leave all gas
appliances shut “OFF” until the water heater installation is
complete.
A gas line of sufficient size must be run to the water heater.
Consult the current edition of National Fuel Gas Code ANSI
Z223.1/NFPA 54 and your gas supplier concerning pipe size.
There must be:
• A readily accessible manual shut off valve in the gas supply
line serving the water heater, and
• A drip leg (sediment trap) ahead of the gas control valve to
help prevent dirt and foreign materials from entering the
gas control valve.
• A flexible gas connector or a ground joint union between the
shut off valve and control valve to permit servicing of the unit.
Be sure to check all the gas piping for leaks before lighting the
water heater. Use a soapy water solution, not a match or open
flame. Rinse off soapy solution and wipe dry.
The minimum inlet gas pressure shown on the rating plate is
that which will permit firing at the rated input.

17
Sediment Traps
Contaminants in the gas lines may cause improper operation
of the gas control valve that may result in fire or explosion.
Before attaching the gas line be sure that all gas pipe is clean
on the inside. To trap any dirt or foreign material in the gas
supply line, a drip leg (sometimes called a sediment trap)
must be incorporated in the piping. The drip leg must be readily
accessible. Install in accordance with the Gas Piping section.
Refer to the current edition of the National Fuel Gas Code,
ANSIZ223.1/NFPA54.
A sediment trap shall be installed as close to the inlet of the
water heater as practical at the time of water heater installation.
The sediment trap shall be either a tee fitting with a capped
nipple in the bottom outlet or other device recognized as an
effectivesedimenttrap.Ifa tee fitting is used, it shallbeinstalled
in conformance with one of the methods of installation, shown
in Figures 19 and 20.
FIGURE19. GASPIPINGWITHFLEXIBLECONNECTOR.
FIGURE20. GASPIPINGWITHALL
BLACKIRON PIPETOGASCONTROL.
Water heaters covered in this manual have been tested and
approved for installation at elevations up to 7,700 feet (2,347m)
above sea level. For installation above 7,700 feet (2,347m),
the water heater’s Btu input should be reduced at the rate of 4
percent for each 1,000 feet (305 m) above sea level which
requires replacement of the burner orifice in accordance with
the National Fuel Gas Code ANSI Z223.1/NFPA 54. Contact
your local gas supplier for further information.
Failure to replace the standard orifice with the proper high
altitude orifice when installed at elevations above 7,700 feet
(2,347m) could result in improper and inefficient operation of
the appliance, producing carbon monoxide gas in excess of
the safe limits. This could result in serious injury or death.
Contact your local gas supplier for any specific changes that
may be required in your area.
Use pipe joint compound or teflon tape marked as being
resistant to the action of petroleum (Propane [L.P.]) gases.
The appliance and its gas connection must be leak tested
before placing the appliance in operation.
The appliance and its individual shut-off valve shall be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
1/2 pound per square inch (3.5 kPa). It shall be isolated from
the gas supply piping system by closing its individual manual
shut-off valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than 1/2 pound
per square inch (3.5 kPa).
Connecting the gas piping to the gas control valve of the water
heater can be accomplished by either of the two methods
shown in Figures 19 and 20.

18
FORYOURSAFETYREADBEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob.Never usetools.If theknobwill notpush inorturn
by hand, don’t try to repair it, call a qualified service
technician.Force orattemptedrepairmayresult inafire
orexplosion.
D. Do not use this appliance if any part has been under
water.Immediately contactaqualifiedinstalleror service
agencytoreplacea floodedwater heater.Donot attempt
torepairtheunit!Itmustbe replaced!
LIGHTINGINSTRUCTIONS
1. Setthermostattothelowestsetting(PILOT LIGHTING).
TOTURN OFFGASTOAPPLIANCE
BEFORE OPERATING: ENTIRE SYSTEM MUST BE FILLED WITH WATERANDAIR PURGED FROMALL LINES.
1. STOP! Readthesafetyinformation
aboveon thislabel.
2. Set thethermostattolowestsetting (PILOTLIGHTING).
Turnthermostat dial fullyclockwise until itstops.
3. Pushthegascontrolknobdownslightlyandturnclockwise
to“OFF”,SEEFIGURE “A”.
NOTE:KnobCANNOT beturnedfrom“PILOT”to “OFF”
unlessitis pusheddown slightly. Donotforce.
4. Remove the outer burner door located below the gas
control.
5. Wait five (5) minutes to clear out any gas. If you then
smellgas, STOP! Follow“B” inthe safetyinformation
aboveon thislabel.Ifyou don’tsmell gas,gotonextstep.
6. Thisunitisequipped witha pushbuttonpilotigniter,which
is used to light the pilot. Locate the igniter on the gas
control.
7. Turn gascontrolknobcounterclockwise to“PILOT”,
SEEFIGURE “B”.
8. Thepilotislocatedonthe rightside ofthe burner.Itcanbe
located by looking through the glass view port while
pressingthepiezoigniter buttonseveraltimes. Lookfora
sparkatthepilotlocation, FIGURE“D”.
9. Once the pilot has been found, push the gas knob all the
waydown. Immediatelypressthepilotigniterbutton rapidly
(4) to (5) times. If the pilot will not light, repeat step (3)
through(9).
10. Continueto holdthe gascontrol knobdown foraboutone
(1)minute afterthepilot islit.Release thegascontrol knob
andit willpopback up.Pilotshould remainlit.If itgoesout,
repeatstep (3)through(9). Itmay takeseveralminutes for
airto clearthe linesbefore thepilotwilllight.
• If knob does not pop up when released, stop and
immediatelycall yourservicetechnician orgas supplier.
• If the pilot will not stay lit after several tries, turn the gas
controlknob clockwise to “OFF”and callyour service
technicianorgassupplier.SEE FIGURE“A”.
11. Oncethepilotflame isestablishedreplacethe outerburner
door.
12. At arms length away, turn gas control knob
counterclockwise to“ON”.SEEFIGURE “C”.
13. Setthermostat todesired setting.
DANGER: Hotter water increases the risk of
scald injury. Consult the instruction manual
before changing temperature.
A. This appliancehas apilot whichis litby apiezo electric
gas ignition system. Do not open the inner door of the
applianceand tryto lightthepilot byhand.
B. BEFORELIGHTINGsmellallaround theappliancearea
forgas. Besureto smellnext tothefloor becausesome
gasisheavier thanair andwill settleonthe floor.
WHATTODOIFYOU SMELL GAS:
• Donot tryto lightanyappliance.
• Donot touchanyelectric switch;do notuse anyphone
inyourbuilding.
• Immediately call your gas supplier from a neighbor’s
phone.Follow thegas supplier’sinstructions.
2. Push gascontrol knobdown slightlyand turnclockwise
to“OFF”. Donotforce. SEEFIGURE“A”.
FIGURE“D”
GAS CONTROL TOPKNOB
OPERATING INSTRUCTIONS

19
THE WATER HEATER SHOULD BE LOCATED IN AN AREA
WHERE THE GENERALPUBLIC DOES NOT HAVE ACCESS.
IFASUITABLEAREAISNOTAVAILABLE,ACOVERSHOULDBE
INSTALLED OVER THE THERMOSTAT TO PREVENT
TAMPERING. Suitable covers are available through the Sears
Service Center.
Never allow small children to use a hot water tap, or to draw
theirownbath water. Neverleaveachild orhandicappedperson
unattended in a bathtub or shower.
NOTE: Awatertemperaturerange of 120°F-140°F(49°C-60°C)
is recommended by most dishwasher manufacturers.
The thermostat of this water heater has been factory set at its
lowest position (PILOT LIGHTING). It is adjustable and must
be reset to the desired temperature setting to reduce the risk of
scald injury. The mark ( ) indicative of approximately 120°F
(49°C) is preferred starting point. Some states have a
requirement for a lower setting.
Turn the water temperature dial clockwise ( ) to decrease
the temperature, or counterclockwise ( ) to increase the
temperature.
Should overheating occur or the gas supply fail to shut off, turn
off the manual gas control valve to the appliance.
FIGURE21.
Temperature Time to Produce 2nd & 3rd
Settings Degree Burns on Adult Skin
VERYHOT=approx.160°F(71°C) About 1/2 second
C = approx. 150°F (66°C) About 1-1/2 seconds
B = approx. 140°F (60°C) Less than 5 seconds
A = approx. 130°F (54°C) About 30 seconds
= approx. 120°F (49°C) More than 5 minutes
LOW = approx. 80°F (27°C) - - - - - - - - - - - - - - - -
FIGURE22.
Temperature Regulation
Due to the nature of the typical gas water heater, the water
temperature in certain situations may vary up to 30F° (16.7 C°)
higher or lower at the point of use such as, bathtubs, showers,
sink, etc.
Any water heater’s intended purpose is to heat water. Hot
water is needed for cleansing, cleaning, and sanitizing (bodies,
dishes, clothing). Untempered hot water can present a scald
hazard. Depending on the time element, and the people
involved(adults, children,elderly, infirm,etc.)scalding mayoccur
at different temperatures.
HOTTER WATER CAN SCALD: Water heaters are intended to
produce hot water. Water heated to a temperature which will
satisfy space heating, clothes washing, dish washing, and
other sanitizing needs can scald and permanently injure you
upon contact. Some people are more likely to be permanently
injured by hot water than others. These include the elderly,
children, the infirm, or physically/mentally handicapped. If
anyone using hot water in your home fits into one of these
groups or if there is a local code or state law requiring a certain
temperature water at the hot water tap, then you must take
special precautions. In addition to using the lowest possible
temperature setting that satisfies your hot water needs, a
means such as a mixing valve, shall be used at the hot water
taps used by these people or at the water heater. Mixing valves
are available at plumbing supply or hardware stores. Follow
manufacturer’s instructions for installation of the valves. Before
changing the factory setting on the thermostat, read the
Temperature Regulation section in this manual, see Figures
21 and 22.

20
Tank (Sediment) Cleaning
Sediment build-up on the tank bottom may create varying
amount of noise, and if left in the tank will cause permanent
tank failure. In some water areas, you may not be able to drain
all sediment deposits by simply draining the tank. In these
cases Mag-Erad (part no. 23600) can be used to help remove
the sediment deposits. This may be ordered from the Sears
Service Center. For ordering, refer to the Parts Order List
section.
Vent System Inspection
At least once a year a visual inspection should be made of the
venting system. You should look for:
• Obstructions which could cause improper venting. The
combustion and ventilation air flow must not be obstructed.
• Damage or deterioration which could cause improper
venting or leakage of combustion products.
• Rusted flakes around top of water heater.
Be sure the vent piping is properly connected to prevent escape
of dangerous flue gasses which could cause deadly
asphyxiation.
Obstructions and deteriorated vent systems may present
serious health risk or asphyxiation.
Chemical vapor corrosion of the flue and vent system may
occur if air for combustion contains certain chemical vapors.
Spray can propellants, cleaning solvents, refrigerator and air
conditioner refrigerants, swimming pool chemicals, calcium
and sodium chloride, waxes, bleach and process chemicals
are typical compounds which are potentially corrosive.
If when inspecting the vent system you find sooting or
deterioration, something is wrong. Call the local gas supplier
to correct the problem and clean or replace the flue and venting
before resuming operation of the water heater.
Burner Inspection
Flood damage to a water heater may not be readily visible or
immediately detectable. However, over a period of time a
flooded water heater will create dangerous conditions which
cancauseDEATH, SERIOUSBODILYINJURY,OR PROPERTY
DAMAGE. Contact a Sears Service Center to replace a flooded
water heater. Do not attempt to repair the unit! It must be
replaced!
At least once a year a visual inspection should be made of the
main burner and pilot burner, see Figure 23.
You should check for sooting. Soot is not normal and will impair
proper combustion.
Soot build-up indicates a problem that requires correction
before further use. Turn “OFF” gas to water heater and
leave off until repairs are made, because failure to correct the
cause of the sooting can result in a fire causing death, serious
injury, or property damage.
FIGURE23.
Burner Cleaning
In the event your burner needs cleaning, following these
instructions:
If inspection of the burner shows that cleaning is required, turn
the gas control knob clockwise ( ) to the “OFF” position,
depressing slightly.
NOTE: The knob cannot be turned from “PILOT” to “OFF”
unless knob is depressed slightly. DO NOT FORCE.
The burner needs to be removed for cleaning. Call the Sears
Service Center to remove and clean the burner and correct the
problem that required the burner to be cleaned.
SERVICE AND ADJUSTMENT
• Flue gases may escape if vent pipe
isnot connected.
• Be alert for obstructed, sooted or
deteriorated vent system to avoid
seriousinjury ordeath.
• Do not store corrosive chemicals
in vicinity of water heater.
• Chemical corrosion of flue and vent
system can cause serious injury or
death