Kenwood KAC-M3004 User manual

Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new power
amplifier.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided
below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product.
Model KAC-M3004 Serial number
US Residence Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
B5A-0393-00/00 (KV)© 2015 JVC KENWOOD Corporation
KAC-M3004
COMPACT 4 CHANNEL DIGITAL AMPLIFIER
INSTRUCTION MANUAL
AMPLIFICATEUR COMPACT 4 CANAUX NUMÉRIQUE
MODE D’EMPLOI
AMPLIFICADOR DIGITAL COMPACTO DE 4 CANALES
MANUAL DE INSTRUCCIONES
KAC-M3004KEnFrEs00.indd1 15/01/1510:33

Warranty Card
© B46-0824-00/02 (K) (14/10)
Identification du produit
Modelo do aparelho e numero de série
Model number & serial number
Revendeur & cachet
Nome da loja e carimbo
Dealer & stamp
Date d’achtat
Data da compra
Purchase date
Nom & adresse du client
Nome e endereço do cliente
Name & address of customer
Attention:
This card and receipt (or invoice) are necessary to purchase a new panel in case of theft
or damage.
Attention:
Vousaurez besoin de cette carte et du reçu (ou de la facture) pouracheter unnouveau
panneau en casde vol ou d'endommagement.
Atenção:
Emcaso de dano ou perda do painel frontal, este Certifi cado de Garantia ea Nota Fiscal
de compra serãorequisitados para a aquisiçãode umnovo painel.
B46-0824-0002K-Warranty.indd114/10/2915:05
KAC-M3004KEnFrEs00.indd1 15/01/1510:33

O fabricante garante o produto identificado na Nota Fiscal de venda ao consumidor contra
qualquer defeito de fabricação ou de matéria-prima durante o período de garantia. Esta garantia
é válida no território brasileiro desde que o produto tenha sido adquirido no Brasil e distribuído
pela JVC KENWOOD do Brasil Comércio de Eletrônicos Ltda.
PERÍODO DE GARANTIA
Este produto é garantido pelo prazo de 01 (um) ano, incluindo o período estabelecido por lei,
a partir da data de aquisição, comprovada mediante a apresentação da respectiva Nota Fiscal
de venda ao consumidor final.
Eventuais reparos realizados no produto durante o período de garantia não implicam na
dilatação do seu prazo.
EXCLUSÃO DA GARANTIA
(a) Produtoscomonúmerodesérieoucertificadodegarantiarasurados,adulteradosouilegíveis;
(b) Defeitos resultantes de acidentes (quedas, batidas e etc), uso em desacordo com o manual
de instruções, má utilização, ligação à fonte de tensão diferente da especificada no Manual
de Instruções, modificações não autorizadas;
(c) Danos causados por agentes da natureza (Ex: chuvas, raios, maresia, enchentes e etc);
(d) Defeitos ou danos em decorrência de consertos realizados por pessoas não autorizadas;
(e) Defeitosoudanosresultantesdousodepeçasoudispositivosnãoconformesàsespecificações
da JVC KENWOOD;
(f) Danos ou deteriorações aos acabamentos externos, partes cosméticas, cabos, chicotes,
parafusos de fixação, luvas, alças, bolsas, estojos, adaptadores, antenas, fitas, cabeças
gravadoras, CDs ou danos causados por pilhas defeituosas ou com vazamento;
(g) Defeitos ou danos devido ao transporte (reclamações devem ser feitas junto à empresa
transportadora);
(h) Qualquer outra causa que não esteja relacionada a defeitos de matéria-prima e de fabricação;
(i) Danos causados por tentativa de roubo ou furto;
(j) Danos causados por uso de CDs de má qualidade;
(k) Danos decorrentes do desgaste natural do produto;
(l) Danoscausadospormauuso.(derramamentodelíquidose/oualimentos,corrosão,oxidação,
exposição à umidade ou situações climáticas extremas, riscos ou quedas).
CONSERTO EM GARANTIA
É indispensável a apresentação deste Certificado de Garantia devidamente preenchido,
acompanhado da respectiva Nota Fiscal de compra do produto, desde que não apresente
rasuras ou modificações.
O consumidor somente terá direito a estes benefícios, quando o produto for entregue diretamente
no balcão de um Serviço Autorizado da JVC KENWOOD.
O QUE NÃO É COBERTO PELA GARANTIA
Instalaçãoeremoçãodoproduto,despesasdefrete,seguro eembalagem sãode responsabilidade
do proprietário.
Este produto é destinado exclusivamente ao uso doméstico.
IMPORTANTE:
Para qualquer informação sobre seu equipamento JVC KENWOOD, ou para obter o endereço do
Serviço Autorizado mais próximo, acesse o site www.kenwood.com.br , ou ligue para a Central
de Atendimento JVC KENWOOD – Tel.: [phone] com os dados abaixo preenchidos.
JVC KENWOOD DO BRASIL COMÉRCIO DE ELETRÔNICOS LTDA
Tel: [phone]
www.kenwood.com.br
Nome do consumidor: ________________________________________
Endereço: _________________________CEP: ___________________
Cidade: ___________________________ Estado: _________________
Telefone: _______________________
Data da compra: _____ / _____ / _____ Nota Fiscal: ______________
JVC KENWOOD DO BRASIL COMÉRCIO DE ELETRÔNICOS LTDA
BRASIL
U.S.A. JVCKENWOOD USA Corporation
This warranty will be honored only in the U.S.A.
KENWOOD LIMITED WARRANTY
FOR CAR STEREO COMPONENTS
HOW LONG IS THE WARRANTY
Kenwood U.S.A. Corporation (“Kenwood”) warrants this
product for a period of one (1) year from the date of original
purchase.
WHAT IS COVERED AND WHAT IS
NOT COVERED
Except as specified below, this warranty covers all defects in
materialandworkmanshipinKenwoodcarstereocomponents.
The following are not covered by the warranty:
1. Any product which is not distributed in the U.S.A. by
Kenwood or which is not purchased in the U.S.A. from an
authorized Kenwood car stereo dealer or an automobile
dealer, unless the product is purchased through the U.S.A
Military Exchange Service.
2. Any product on which the serial number has been defaced,
modified or removed.
3. Damage, deterioration or malfunction resulting from:
a. Any shipment of the product (claims must be presented
to the carrier).
b. Installation or removal of the product.
c. Accident, acts of nature, misuse, abuse, neglect,
unauthorized product modification or failure to follow
instructions supplied with the product.
d. Repair or attempted repair by anyone not authorized
by Kenwood.
e. Any other cause which does not relate to a product
defect.
WHO IS PROTECTED
This warranty is enforceable only by the original purchaser.
WHAT WE WILL PAY FOR
We will pay for all labor and material expenses for covered
items. Payment of shipping charges is discussed in the next
section of this warranty.
HOW TO OBTAIN WARRANTY
SERVICE
If your KENWOOD product ever needs service:
1. Take or ship it to any KENWOOD Authorized Service Center
in the U.S.A. along with & complete description of the
problem.(ifyouareuncertain as to whether a Service Center
isauthorized,pleasecall1-800-KENWOOD forthenearest
Service Center. 1-800-536-9663).
2. Althoughyoumustpayanyshippingchargesifitisnecessary
toshiptheproductforwarrantyservice,wewillpaythereturn
shipping charges if the repairs are covered by the warranty
within the United States.
3. Whenever your units are taken or sent for warranty service,
you must include a copy of the original dated sales receipt
as proof of warranty coverage.
LIMITATION OF IMPLIED
WARRANTIES
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF
THIS WARRANTY.
EXCLUSION OF DAMAGES
KENWOOD’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS
LIMITEDTOTHEREPAIRORREPLACEMENTOFTHEPRODUCT
AT OUR OPTION. KENWOOD SHALL NOT BE LIABLE FOR:
1. INSTALLATION OR REMOVAL CHARGES, DAMAGE
TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN
KENWOOD CAR STEREO COMPONENTS, DAMAGES
BASED UPON INCONVENIENCE, LOSS OF USE OF THE
PRODUCT; OR
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT
ALLOWTHE EXCLUSIONOR LIMITATIONOF INCIDENTALOR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
AND EXCLUSIONS MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
IfaproblemdevelopsduringoraftertheLimitedWarrantyPeriod,
or if you have any questions regarding the operation of the
product,youshouldcontactyourKENWOODAuthorizedDealer
orAuthorizedServiceCenter. If theproblemoryour question is
not handled to your satisfaction, please contact our Customer
Relations Department at the address listed below:
JVCKENWOOD USA Corporation
PO Box 22745, 2201 E. Dominguez St .
Long Beach, CA 90810-5745
Tel: [phone]
www.us.jvckenwood.com
B46-0824-0002K-Warranty.indd214/10/2915:05
KAC-M3004KEnFrEs00.indd1 15/01/1510:33

CANADA KENWOOD ELECTRONICS CANADA INC.
KENWOOD WARRANTY
KENWOOD ELECTRONICS CANADA INC. (hereinafter called
“KENWOOD”), gives the following written warranty to the
originalcustomerofeachnew Kenwood product distributed in
CanadabyKENWOODandpurchasedfromadealerauthorized
by KENWOOD.
KENWOOD warrants that each new Kenwood product, under
normal use, is free from any defects, subject to the terms and
conditions set forth below. If a defect should occur within the
warranty period, repairs will be made free of charge for parts
and labour when such defects are determined by KENWOOD
or its’ authorized service centres to be attributable to faulty
materials or workmanship at time of manufacture. Please
contact KENWOOD to confirm if a dealer or service centre is
authorized by KENWOOD.
WARRANTY PERIOD
This Kenwood product is warranted for parts and labour for a
period of one (1) year from the date of original purchase, lease
or rental, except for products which are used in a professional
or commercial application, which are warranted for a period
of ninety (90) days for parts and labour and are subject to the
terms and conditions of the warranty.
WARRANTY EXCLUSIONS
This warranty excludes:
(a) Products purchased in a foreign country or purchased in
Canada and taken to a foreign country.
(b) Products purchased from a dealer not authorized by
KENWOOD.
(c) Products with the serial number defaced, altered or
missing.
(d) Periodic check-ups which do not disclose any defects
covered by this warranty.
(e) Defects resulting from disaster, accident, abuse, misuse,
lightning, power surges, neglect or lack of periodic
maintenance,unauthorizedmodification or failure tofollow
instructions in the owner’s manual.
(f) Defects or damage as a result of repairs performed by a
person or party not authorized by KENWOOD.
(g) Defects resulting from the use of parts or devices that do
not conform to KENWOOD specifications.
(h) Damage or deterioration occurring to any exterior finishes,
cosmetic parts, tape heads, adaptors, antennas, cables,
tapes, discs or faults or damage caused by defective or
leaking batteries.
(i) Defectsordamageoccurringduringshipping(claimsshould
be presented to the shipping company).
(j) Product voltage and /or line frequency conversions.
(k) Product installation or removal charges.
TO OBTAIN WARRANTY SERVICE
ShouldyourKenwoodproductrequirewarrantyservice,deliver
it to any authorized KENWOOD service centre and present
the original copy of your bill of sale and this warranty card
as proof of warranty, or send your product fully insured and
freight prepaid to the nearest authorized KENWOOD service
centre. To avoid possible shipping damage, make sure the
product is properly packed. Include a copy of your original
bill of sale and this warranty card as proof of warranty along
with your name, home and /or work telephone number(s),
a complete return address and a detailed description of the
fault(s). Products repaired within warranty will be returned
freight prepaid to destinations within Canada. The customer
is responsible for all freight and related costs for the return of
product(s) to destinations outside Canada.
ENTIRE WARRANTY
This warranty constitutes the entire written warranty given
by KENWOOD. No person, party, dealer or service centre
or their agents or employees are authorized to extend or
enlarge this warranty on behalf of KENWOOD by any written
or verbal statement or advertisement or promotion, including
any extended warranty program or plan that may be offered
by the dealer or service centre, unless approved in writing
by KENWOOD.
DISCLAIMER
KENWOOD disclaims any responsibility for loss of time or use
oftheproduct or anyotherindirect,incidental or consequential
damage to other products or goods, inconvenience or
commercial loss.
NOTICE TO CONSUMER
Theprovisionscontainedinthiswrittenwarrantyarenotintended
to limit, modify, take away, disclaim or exclude any warranties
or rights you may have which are set forth in any applicable
provincial or federal laws or legislation.
IMPORTANT
This warranty card by itself is not considered by KENWOOD as
a valid proof of purchase. When applying for warranty repairs,
you must present the original copy of your bill of sale and this
warrantycardasproofofwarranty,sowerecommendthattheybe
kept in a safe place, should they be required in the future.
KENWOOD ELECTRONICS CANADA INC.
6070 Kestrel Road, Mississauga,
Ontario, Canada L5T 1S8
Tel.: [phone]
Fax: [phone]
GARANTIE KENWOOD
KENWOOD ELECTRONICS CANADA INC. (ci-après appelée
“KENWOOD”), donne par écrit la garantie suivante à l’acheteur
original de chaque nouveau produit Kenwood distribué au
CanadaparKENWOODetachetéàunconcessionnaireautorisé
par KENWOOD.
KENWOODgarantit,sousréserve des termes etdesconditions
énoncés ci-dessous, que chaque nouveau produit Kenwood,
dans des conditions d’emploi normales, est exempt de tous
défauts.Sil’undéfautseproduitpendantla périodedegarantie,
KENWOODs’engageàassumerlecoûtdespiècesdéfectueuses
etdelamain-d’oeuvrenécessairespoureffectuerlesréparations
pourvu que de tels défauts sont attribuables à des pièces
défectueuses employées lors de la fabrication du produit
Kenwood ou à la main-d’oeuvre tel qu’établi par KENWOOD ou
parl’undesescentresdeserviceautorisés.AppelezKENWOOD
pour vérifier si un concessionnaire ou un centre de service est
autorisé par KENWOOD.
PÉRIODE DE GARANTIE
Les pièces et la main-d’oeuvre nécessaires pour la réparation
desproduitsKenwoodsontgarantiespendantlapérioded’un(1)
anàcompter de ladated’achat, de bailoudelocation originale,
saufdans les casoùles produits Kenwoodsontemployés dans
un but professionnel ou commercial, où la garantie des pièces
etdelamain-d’oeuvredemeureenvigueurpendantunepériode
de quatre-vingt-dix (90) jours sous réserve des termes et des
conditions de la garantie.
EXCLUSIONS DE GARANTIE
Cette garantie ne couvre pas:
(a) les produits achetés à l’étranger ou achetés au Canada et
transportés à l’étranger;
(b) les produits achetés à un concessionnaire non autorisé
par KENWOOD;
(c) les produits dont le numéro de série manque, a été effacé
ou modifié;
(d) les services d’entretien périodiques qui n’indiquent aucun
défaut couvert par cette garantie;
(e) les défauts causés par les désastres, les accidents, les
abus, les emplois incorrects, les éclairs, les surtensions de
courant,lesmanquesdesoinsoud’entretiens périodiques,
lesmodificationsnonautoriséesoulesmanquesde respect
du mode d’emploi;
(f) les défauts ou les dommages causés lors de réparations
effectuéespar unepersonneouparune partienon autorisée
par KENWOOD;
(g) lesdéfautscausésparl’emploidepiècesoudedispositifsqui
ne se conforment pas aux exigences de KENWOOD;
(h) les finitions extérieures, les pièces cosmétiques, les têtes
de bandes, les adaptateurs, les antennes, les câbles,
les bandes, les disques endommagés ou dépéris, ni les
défauts ou dommages causés par des piles défectueuses
ou qui fuient;
(i) les défauts ou dommages qui se produisent pendant
l’expédition des produits Kenwood (On devrait déposer de
telles réclamations auprès des compagnies de transport);
(j) les conversions de tension et/ou de fréquence du
produit;
(k) les frais d’installation ou d’enlèvement du produit.
COMMENT OBTENIR DU SERVICE
SOUS GARANTIE
Au cas où un service sous garantie de votre produit Kenwood
s’avère nécessaire, veuillez livrer le produit à n’importe quel
centre de service KENWOOD et présenter la copie originale du
contrat de vente et cette carte de garantie en tant que preuve
de garantie ou veuillez faire parvenir votre produit assuré et
port payé au centre de service KENWOOD autorisé le plus
proche. Pour éviter toutes possibilités de dommages pendant
le transport, veuillez bien emballer le produit. Veuillez inclure
une copie du contrat de vente original et cette carte de garantie
en tant que preuve de garantie aussi bien que votre nom,
numéros de téléphone au poste de travail et/ou au domicile,
votre adresse et une description détaillée des défauts. Les
produits sous garantie réparés seront retoumés port payé aux
destinations à l’intérieur du Canada. Le consommateur sera
responsable de tous frais de transport et d’autres frais qui s’y
rapportent pour faire expédier les produits à destinations à
l’extérieur du Canada.
L’ENTIÈRE GARANTIE
Cettegarantie représente l’entière garantie donnée par écrit par
KENWOOD. KENWOOD ne se tient aucunement responsable
de toutes extensions ni de toutes augmentations de cette
garantie faites ou entreprises par toutes personnes, parties,
concessionnaires ou centres de service ou par leurs agents
ou employés au nom de KENWOOD au moyen d’affirmations
verbalesouécrites,d’annoncesoudepromotions,yinclustous
programmes ou plans de garantie étendue que puissent offrir
les concessionnaires ou les centres de service, à moins que
KENWOOD n’y ait consenti par écrit d’avance.
RENONCIATION
KENWOODrenonceàtoutesresponsabilitésdepertedetemps,
d’emploiduproduit,detousdommagesindirectsouaccessoires
causés à d’autres produits ou biens, de tous inconvénients ou
de toutes pertes commerciales.
AVIS AUX CONSOMMATEURS
Lesstipulationscontenuesdanslaprésentegarantieécriten’ont
pas pour but de limiter, de modifier, de diminuer, de rejeter ni
d’exclure d’autres garanties ni droits énoncés dans n’importe
quelles lois ou législations provinciales ou fédérales.
IMPORTANT
KENWOOD ne considère pas cette garantie toute seule comme
étantunepreuve d’achat valide. Lorsqu’on demandeduservice
sousgarantie,ilfaudraprésenterlacopieoriginaleducontratde
vente aussi bien que cette carte de garantie en tant que preuve
de garantie. On recommande de les conserver dans un lieu sûr
au cas où elles s’avèreraient nécesaires à l’avenir.
KENWOOD ELECTRONICS CANADA INC.
6070 Kestrel Road, Mississauga,
Ontario, Canada L5T 1S8
Téléphone: [phone]
Télécopieur: [phone]
B46-0824-0002K-Warranty.indd214/10/2915:05
KAC-M3004KEnFrEs00.indd1 15/01/1510:33

Dear Customer,
Thank you for purchasing this kenwood product. As mentioned in the pages of this booklet, our warranty is only
valid in the countries listed. If your country is not listed please contact your retailer for information on warranty
procedure, or write to:
JVC KENWOOD Customer Information Center
3-12, Moriyacho, Kanagawa-ku, Yokohama-shi, Kanagawa 221-0022, Japan
Units purchased through the U.S.A. military exchange service
overseas may be serviced under warranty in the continental
U.S.A., subject to the following conditions.
1) The original warranty is in effect.
2) Proof of purchase is provided to the servicer.
WARRANTY FOR MILITARY MARKET
Kenwood corporation is proud of the quality and workmanship
of its audio equipment. This unit has been properly designed,
tested and inspected before it was shipped to you. If properly
installedandoperatedinaccordancewithinstructionsfurnished,
it should give you an optimum reliable performance.
WARRANTY PERIOD
This product is warranted for a period of (1) year from the date
of the original purchase.
SCOPE OF WARRANTY
Except as specified below, this warranty covers all defects in
materials and workmanship of the Kenwood brand products.
During the warranty period, any authorized Kenwood Service
Center in the military market listed in the back of this warranty
card will provide you free-of-charge both parts and labor
required to correct any defect in materials or workmanship.
The following are not covered by this warranty.
1. Voltage conversions.
2. Periodiccheck-upswhichdonotdiscloseanydefectcovered
by the warranty.
3. Cabinets, grilles, other exterior finishes, belts, tape heads,
and other non-durable parts and accessories.
4. Unitsonwhich the serialnumberhas been effaced,modified
or removed.
5. Installation and/or removal charges.
6. Damaged magnetic tapes.
7. House call charges for any repairs.
8. Shipping or delivery charges to or from an authorized
Kenwood Service Center.
9. Thiswarrantywillnotcoveranyfailurethatisduetoanyofthe
followingconditionsinaccordancewiththevisualinspection
of the authorized Kenwood Service Center:
* Improper maintenance or repair, including the installation of
parts or accessories that do not conform to the quality and
specifications of the original parts.
* Misuse, abuse, neglect, unauthorized product modification
or failure to follow instructions contained in the Owner’s
Manual.
* Accidental or intentional damages.
* Repairs or attempted repairs by an unauthorized agency.
(All repairs must be performed at an authorized Kenwood
Service Center.)
* Damages or deteriorations caused during shipment (Claims
must be presented to the carrier).
* Damages or deteriorations resulting from removal and/
or replacement.
PURCHASER’S RESPONSIBILITIES
As the purchased of a new Kenwood brand product, you are
requested to do the following in order to obtain Kenwood
warranty service.
1. Retainyoursalessliporotherevidenceofpurchaseforproving
your eligibility for requesting Kenwood warranty service.
2.Make your unit available to an authorized Kenwood Service
Center in the military market for inspection and approved
warranty service, or ship your unit in its original carton box
or equivalent, fully insured and shipping charges prepaid,
to the authorized Kenwood Service Center.
LIMITATION OF IMPLIED
WARRANTIES
Any and all implied warranties, including warranties of
merchantability and fitness for a particular purpose, shall be
limited in duration to the length of this warranty.
EXCLUSION OF CERTAIN DAMAGES
KENWOOD’s liability for any defective product is limited to
the repair or replacement of said product, at our potion, and
shall not include damages of any kind, whether incidental,
consequential or otherwise, expect to the extent prohibited
by applicable law.
KENWOOD AUTHORIZED SERVICE
CENTERS IN MILITARY MARKET
JAPAN:
Yokota
Kenwood Rep,; c/o
Yokota BX, JAAX AAFES-PAC,
APO San Francisco 96328
Zama
Kenwood Rep,; c/o
Zama PX, JAAX AAFES-PAC,
APO San Francisco 96343
Misawa
Kenwood Rep,; c/o
Misawa BX, JAAX AAFES-PAC,
APO San Francisco 96519
Yokosuka
Kenwood Rep,; c/o
A-33, Yokosuka NEX No. 260-010
FPO Seattle 98760
Atsugi
Kenwood Rep,; c/o
Atsugi NEX No. 260-020 FPO Seattle
98767
Iwakuni
Kenwood Rep,; c/o
Marine Corps Exchange, Marine Corps
Air Station,
FPO Seattle 98764
Sasebo
Sasebo NEX;
Navy Exchange 260-040
F.A. Box 115 FPO Seattle 98766
Okinawa
Kenwood Rep,; c/o
OWAX, AAFES-PAC, APO San Francisco
96230
KOREA:
Kenwood Rep,; c/o
KOAX Repair Shop, AAFES-PAC
DD-Camp Market, APO San Francisco
96488
GUAM:
Kenwood Rep,; c/o
Guam NEX No. 230-010,
FPO San Francisco 96630
Kenwood Rep,; c/o
GUAX, AAFES-PAC, APO San Francisco
96334
U.S.A.:
In The Continental U.S.A.
For Nearest Authorized Service Center;
Tel: [phone]
www.us.jvckenwood.com
EUROPE:
Please inquire at the military resale
outlets where you bought your
Kenwood products, or
KENWOOD ELECTRONICS
DEUTSCHLAND GMBH:
Rembrücker-Str. 15, 63150
Heusenstamm, Germany
Tel.: [phone]
MILITARY
B46-0824-0002K-Warranty.indd114/10/2915:05
KAC-M3004KEnFrEs00.indd1 15/01/1510:33

Combined impedance
FCC WARNING
This equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate
this equipment if an unauthorized change or modification is made.
FCC NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment may cause harmful
interference to radio communications, if it is not installed
and used in accordance with the instructions. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Safety precautions
WARNING
To prevent injury or fire, take the following
precautions:
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and
wiring work to professionals.
• When extending the ignition, battery, or ground wires,
make sure to use automotive-grade wires or other wires
with the range of 5 mm² (AWG10)or more to prevent
wire deterioration and damage to the wire coating.
• To prevent a short circuit, never put or leave any metallic
objects (such as coins or metal tools)inside the unit.
• If the unit starts to emit smoke or strange smells, turn
off the power immediately and consult your Kenwood
dealer.
• Do not touch the unit during use because the surface of
the unit becomes hot and may cause burns if touched.
CAUTION
To prevent damage to the machine, take the following
precautions:
• Be sure the unit is connected to a 12V DC power supply
with a negative ground connection.
• Do not open the top or bottom covers of the unit.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid places
with too much dust or the possibility of water splashing.
• When replacing a fuse, only use a new one with the
prescribed rating. Using a fuse with the wrong rating
may cause your unit to malfunction.
• To prevent a short circuit when replacing a fuse, first
disconnect the wiring harness.
NOTE
• If you experience problems during installation, consult
your Kenwood dealer.
• If the unit does not seem to be working right, consult
your Kenwood dealer.
Cleaning the unit
If the front panel gets dirty, turn off the power and wipe
the panel with a dry silicon cloth or soft cloth.
CAUTION
Do not wipe the panel with a hard cloth or a cloth
dampened by volatile solvents such as paint thinner and
alcohol. They can scratch the surface of the panel and/or
cause the indicator letters to peel off.
To prevent battery rise
When the unit is used in the ACC ONposition without
turning the engine ON, it depletes the battery. Use it after
starting the engine.
Protection function
The protection function is activated in the following situations:
This unit is equipped with a protection function for
protecting this unit and your speakers from various
accidents or problems that can occur.
When the protection function is triggered, the amplifier
stops operating.
Power indicator goes off:
• When the unit malfunctions.•
When the internal temperature is high and unit won’t operate.
Power indicator lights continuously:
• When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
7Wiring
• Take the battery wire for this unit directly from the
battery. If it’s connected to the vehicle’s wiring harness, it
can cause blown fuses etc.
• If a buzzing noise is heard from the speakers when the
engine is running, connect a line noise filter (optional)to
each of the battery wire.
• Do not allow the wire to directly contact the edge of the
iron plate by using Grommets.
• Connect the ground wire to a metal part of the car
chassis that acts as an electrical ground passing
electricity to the battery‘s negative ·terminal. Do not
turn the power on if the ground wire is not connected.
• Be sure to install a protective fuse in the power cord
near the battery. The protective fuse should be the same
capacity as the unit’s fuse capacity or somewhat larger.
• For the power cord and ground, use a vehicle type
(fireproof)power wring cord. (Use a power wiring cord
with the range of 5 mm² (AWG10)or more.)
• When more than one power amplifier are going to be
used, use a power supply wiring wire and protective
fuse of greater current-handling capacity than the total
maximum current drawn by each amplifier.
7Speaker selection
• Using speakers with smaller input ratings than the
amplifier’s output power would result in smoke
generation or equipment failure.
• The impedance of the speakers that are going to
be connected should be 2Ω or greater (for stereo
connections), or 4Ω or greater (for bridged connections).
When more than one set of speakers are going to be
used, calculate the combined impedance of the speakers
and then connect suitable speakers to the amplifier.
<Example>
KAC-M3004KEnFrEs00.indd1 15/01/1510:33

165 mm (6-1/2”)
177 mm (6-15/16”)
190 mm (7-1/2”)
76 mm (3”)
99 mm (3-7/8”)
45
mm
(1-3/4”)
Spare
De rechange
Repuesto
MOISTURE
HUMIDITÉ
HUMEDAD
DUST
POUSSIÈRE
POLVO
7Installation procedure
Since there are large variety of settings and connections
possible according to applications, read the instruction
manual well to select the proper setting and connection.
1. Remove the ignition key and disconnect the negative ·
terminal of the battery to prevent short circuits.
2. Set the unit according to the intended usage.
3. Connect the input and output wires of the units.
4. Connect the speaker wires.
5. Connect the power wire, power control wire and
grounding wire following this order.
6. Attach the unit.
7. Connect the negative ·terminal of the battery.
CAUTION
• Do not install in the below locations;
(Unstable location, In a location that interferes with
driving, In a location that gets wet, In a dusty location, In
a place that gets hot, In a place that gets direct sunlight,
In a location that gets hit by hot air)
• Do not install the unit under the carpet. Otherwise heat
build-up occurs and the unit may be damaged.
• Install this unit in a location which allows heat to easily
dissipate.
Once installed, do not place any object on top of the
unit.
• The surface temperature of the amplifier will become hot
during use. Install the amplifier in a place where people,
resins, and other substances that are sensitive to heat will
not come into contact with it.
• When making a hole under a seat, inside the trunk,
or somewhere else in the vehicle, check that there
is nothing hazardous on the opposite side such as a
gasoline tank, brake pipe, or wiring harness, and be
careful not to cause scratches or other damage.
• Do not install near the dashboard, rear tray, or air bag
safety parts.
• The installation to the vehicle should securely fasten the
unit to a place in which it will not obstruct driving. If the
unit comes off due to a shock and hits a person or safety
part, it may cause injury or an accident.
• After installing the unit, check to make sure that
electrical equipment such as the brake lamps, turn signal
lamps and windshield wipers operate normally.
Protective cover 2
Couvercle de protection 2
Cubierta protectora 2
After setting up the unit, put the protective cover 2on the
control panel.
Après avoir configuré l’unité, placez le couvercle de
protection 2sur le panneau de commande.
Después de configurar la unidad, coloque la cubierta
protectora 2sobre el panel de control.
Installation / Installation / Instalación
7 Accessories / Accessoires / Accesorios
1Speaker cable
Câble d’enceinte
Cable de altavoces 1
2Protective cover
Couvercle de protection
Cubierta protectora 2
3Wire band
Serre-câble
Atadura de cables 2
4
ø 4 x 16 mm
Self-tapping screws
Vis taraudeuses
Tornillo autorroscantes 4
Installation board, etc. (thickness : 15 mm or more)
Tableau d’installation, etc. (épaisseur : 15 mm ou plus)
Tablero de instalación, etc. (grosor : 15 mm o más)
3Parts included
Pieces comprises
Partes incluidas
4Parts included
Pieces comprises
Partes incluidas
Example A: using the screws
Exemple A: utilisation des vis
Ejemplo A: utilizando los tornillos
Example B: using the wire bands
Exemple B: utilisation des serre-câbles
Ejemplo B: utilizando los atadura de cables
KAC-M3004KEnFrEs00.indd2 15/01/1510:33

Connection I RaccordementsI Conexiones
A.WARNING
A AVERTISSEMENT
A
ADVERTENCIA
Remove the ignition key and disconnect the negative 8 terminal of the battery to prevent short circuits.
Retirer la de de contact etdebrancher la bornenegative 8 de la batterie pour eviter les court-circuits.
Retire la Have de encendido y desconecte el terminal negativo 8 de la bateria para evitar cortocircuitos.
! .A.WARNING I
Particular attention must be given
to making good elearical contact
at the amplifier-output and
speaker termi nals.
Poor or loose connections can cause sparking or burning at the
terminals
because of thevery high powerthat the amplifier can deliver.
I .A. CAUTION I
•
If sound is not output normally,immediately turn power off and
check connections.
•
Be sure to turn the power off before changing the setting of any
swi tch.
•
If the fuse blows, check wires for shorts, then repl ace the fuse with
one
of the same rating.
• Check that no unconnected wires
or connectors are touching
the
car body. Do not remove caps from unconnected wires or
connectors to preventshort circuits.
• Connectthe speakerwires
to appropriate speaker connectors
separately.
Sharing the negative wire ofthe speaker or grounding
speaker wires to the metal body of thecar can cause this unitto fail.
• After installation, check that the brake lamp s. turn signal lampsand
windshield wipers work properly.
!
.A. AVERTISSEMENT I
Vei ll ez ace que le contact electrique a la sortie de l'amplificateuret
aux prises des enceintes soil bien etabli.
Un
mauvais branchement ou un branchement !ache peut causer de s
etincell
es ou un rechauffement des prises du fait de la tres grande
puissance de l'amplificateur.
I
.A. ATTENTION I
• En cas d'anomalie, mettre immediatement l' appareil hors tension et
vCriftcr tous lc5 r-Jccordcmcnt::;.
• Veiller amettre l'appareil
hors tension avant de changer la position
des commutateurs.
•
Si le fusible saute ,verifier si l es ~bles ne sont pas court- circuites, et
rempl acer le fusible par un autre fusible de m~me capacite nominale
• Verifier qu'aucun cable ou connecteurnon raccorde
ne touche la
carros serie de la voiture Ne pas retirer es capucho ns des cables ou
connecteurs non
raccordes afin d'eviter tout courtcircuit.
•
Ra ccorder separement les cabl es de haLt-parleur aux connecteurs de
haut-parleur appropries . La mise en commun du cable negatifd' un
haut-parleur ou des fils de masse des haut-parleurs ala carros serie
metal
liq uede lavoiture pourrait rendre l'appareil inoperant.
• Apres l'lnstallation, verifier
que l es voyants de frein, les clignotants
et l
es es suie-glace fonctionnent correaement
!
.A. ADVERTENCIA I
Debe ponerse especial atenci6n para que se haga un buen contacto
electrico
en la sa li da del amplificador yen los terminales de los
a
lt av oces .
L
as conexiones mal hechas o l as conexicnes flojas pueden causar
chispas o quemaduras en l os terminales debido a la potencia muy
a
lt aque puede suministrar el amplificador.
!
.A. PRECAUCION I
•
Si el sonido no sa le normalmente, desconecte inmediatamente la
alimentaci6n y compruebe
las conexiones.
• No
se olvide de desconect ar la alimentaci6n antes de cambiar el
ajuste de
cua lquierconmutador.
• Si
el fusible se quema, compruebe que no haya un cortocircuito
en los cables, luegocambie el fusible ~or uno que tenga el mismo
amperaje.
• Verifique que ninguno
de los cab les o coneaores que estan sin
conectar se encuentren tocando la ca rr ocerfa del autom6vil. No
retire
las tapas de lo s cabl es o conectoresque estan sin coneaar
para evitar
de que se produzcan cortocircuitos.
• Conecte los
cables del a lt avoz a l os conectores adecuados de l
a
lta voz separadamente La puesta en contacto de terminales
de altavoces distintos, o la conexi6n cc
mo toma de tierra de los
terminales del altavoz
al coche del autom6vil, pueden causar dafios
a la unidad.
• Despues de la instalaci6n, compruebe que las l amparas del freno,
luces
de deste ll o y lim piaparabrisas funcionar correctamente.
■
Power wire and speaker wire connection
■ Raccordement d'un cable de l 'a limentation et d'enceinte
■ Conexion del cable de alimentaci6n y del altavoz
Power control wire
AFTER MARKET HEAD UNIT only
AFTER MARKET
HEAD UNIT
Cable de commande de l'alimentation
AFTER MARKET HEAD UNIT uniquement J
Cable
de control de alimentaci6n
AFTERMAR/K ~E~T=H= EA = D~U=N= IT =s=o= la~m =e= nt =e~~ .q-F = <? =• =l
■ RCA
INPUT connection
■ Raccordement RCA INPUT
■ Conexion RCA INPUT
AFTER MARKET
HEADUNrr
RCAcabl~-
Cable RCA
Cable RCA
~ -
~~
-11r.
...i, -
■ SPEAKER INPUT connection
■ Raccordement SPEAKER INPUT
■ Conexion SPEAKER INPUT
FACTORY INSTALLED ~ ig
HEAD UNrr ~ ! i
~.,. o ~> i=i'f==;..
~•e '-
~!g
Speaker line to male RCA_
adapter
Ligne de haut-parleur a
adaptateur RCA male
Lfnea de altavoz a adaptador
RCA macho
Protective fuse
Fusible
de protection
Fusible
de protecci6n
~
System examples/ Exemple de configuration/ Ejemplos del sistema
■ 4-channel system/ Systeme 4 voies / Sistema de 4 canal es
-Ground wire
cable de masse
Cable
de masa
e"
Battery/ Batterie / Baterfa
!AWARNING!
To prevent fire caused bya short in the wiring,
connect a fusible link
or breaker nearby the
battery's positive terminal.
!
.A. AVERTISSEMENT I
Pour eviter tout incendie dO aun court-circui~
inserer
un fusible ou un coupecircuit aproximite
de la borne
de la batterie.
!
.A. ADVERTENCIA I
Para evitarincendios producidos por
cortocircuit
os en el cabl eado, conecte un fusible
o cortacircuito entre
la baterfa y lo sterminales de
la ba terfa.
*1
The output from the F ACTORY INST A LLED HEAD UNIT
up to SOW can be input.
The power is turned on and off as the unit detects
input
signa l (S IGN AL SENS IN G TURN-ON) . Therefore it
is not necessary to connea the power control wire.
La puissance de sortie maximum de la FACTORY
IN STAL LED HEAD UNIT ne doit pas depa s ser SOW.
L'alimentation est aaivee et desactivee lorsque
l'appareil deteae
le signal d'entree (SIGNAL SENS IN G
TURN- ON). Cest pourquoi ii n'est pas necessaire de
connecter le cable de commande de l'alimentation.
El FACTORY INST A LLED HE AD UNIT debera tener una
potencia de
salida maxima no superior a SOW .
La alimentaci6n se enciende y apaga conforme
la unidad detecte una sena l de entrada (SIGNA L
SENSING TURN-ON) . Por lo tanto no es necesario
coneaar el cable de control de
al imentaci6n.
HEADUNrr
ll',liite) IBlanc)IBlanco) ~ 0 Front leftspeaker
Haut-parleur avant
gauche
ll'lllite/Bladc] (Blanc/No r) (Blanco/Negro]0 Altavoz delantero Izquierdo
"IGray)IGris]IGris) [!ill~ Front right sp eaker
'------------ Haut-parleur avant droit
!Gray/Blade) IGr isMoir) !Gris/Negro] Altavoz delantero derecho
!Green] [Vert]IVerde ) l!iliJ0 Rear left speaker
Haut-parleur arriel'e
gauche
(Green,1!1adcl (Vert/Noir) [Verde/Negro) Altavoz trasero izquierdo
!Purple] IV"tolet) (Purp<ireo]
Rear right speaker
Haut-parleur arriel'e droit
Altavoz trasero derecho
■ High-power2-channel system/ Systeme 2 voies, puissance elevee / Sistema de 2 canales de alta potencia
HEADUNrr
L
R
h
l'lllite] !Blanc) !Blanco] ~ o
!Gray/Blade] IGr isMoir) !Gris/Negro]
e
(Wh iti/Bladcl IBlanc/Noir] 1Blanco/N09"ol
( Gre,n/Bladc] IVert/Noir) [Verde/Negro]
[Gra ) (Gris] !Gris)
!l'llrple) [Viol•tl !l'llrpureo]
! Green] !Vert) IVa-de)
!Purple/Blade) l 'llolet/Noir) [Pur pureo/Negro) e
Left speaker [Bridged)
Haut-parleur
gaucne (Pont)
Altavoz izquierdo (Puenteada )
Prevent a short circuit!
Eviter
les court-circuits!
i Evitar cortoc1rcuitos1
Right speaker [Bridged)
Haut-parleur
droit (Pont)
Altavoz
derecho ( Puenteda)
■ 2-channel + Subwoofer system/ Systeme 2 voies + enceinte d'extremes graves /
Sistema de 2 canales + Altavoz de subgraves
HEADUNrr
ll'lll~e) IB~nc]IBlanco] [!ill 0
!White/Black) (Blanc/Noir) (Blanco/Negro) e
(Gray]IGris]IGris) ~0
!Gray/Blade] [Gris/Noir) (Gris/N'9'ol
e
!Green) [Vert) !Verde)
l!ili]o
!Purple/Blade) l 'llolet/Noir) IPur pureo/Negro) 0
[Green/Black] IVert/Noir) [Verde/Neg'o]
!Purple] IV"tolet) [Purp<ireo]
Left speaker (high pass)
Haut-parleur
gauche (filtre passe-haut)
Altavoz izquierdo (paso alto )
Right speaker (High pass)
Haut-parleur droit [filtre passe-haut)
Altavoz derecho fpaso alto)
Subwoofer [Bridged)
Haut-parleur d'extremes graves (Pont)
Altavoz
de subgraves (Puenteada )
Prevent a short circu1tl
£v1ter
les court-circuits1
I
Evitarcortocircuitos I

Controls / Contrôles / Controles
This is a 4 channel amplifier
including 2 stereo amplifiers in a
body. One amplifier is referred to as
amplifier A and the other is amplifier
B. This unit is compatible with a large
variety of systems by combining the
switches and functions described in
the following.
1Fuse (30 A)
NOTE
If you can’t find the specified capacity
fuse at your store etc., consult your
Kenwood dealer.
2Battery terminal (BATT.)
3Ground terminal (GND)
4Power control terminal (P.CON)
Controls the unit ON/OFF.
NOTE
Controls the unit power. Be sure to
connect it with all the systems.
5SPEAKER OUTPUT terminals
(A.ch/B.ch)
• Stereo
connections:
When you wish to use the unit as a stereo
amplifier, stereo connections are used.
The speakers to be connected should have
an impedance of 2Ω or greater. When
multiple speakers are to be connected,
ensure that the combined impedance is
2Ω or greater for each channel.
• Bridged connections:
When you wish to use the unit as a high-
output amplifier, bridged connections
are used. (Refer to <High-power
2-channel system> or <2-channel +
Subwoofer system> of <Connection>.)
The speakers to be connected should
have an impedance of 4Ω or greater.
When multiple speakers are to be
connected, ensure that the combined
impedance is 4Ω or greater.
6FILTER FREQUENCY control
(A.ch/B.ch)
Sets the cutoff frequency when the
“FILTER” switch is set to “HPF” or “LPF”.
7FILTER switch (A.ch/B.ch)
This switch allows to apply high-pass or
low-pass filtering to the speaker outputs.
• HPF (High-Pass Filter) position:
The filter outputs the band of higher
frequencies than the frequency set with
the “FILTER FREQUENCY” control.
• OFF position:
The entire bandwidth is output without
filtering.
• LPF (Low-Pass Filter) position:
The filter outputs the band of lower
frequencies than the frequency set with
the “FILTER FREQUENCY” control.
8LINE IN terminal (A.ch/B.ch)
9INPUT SENSITIVITY control
(A.ch/B.ch)
Set this control according to the
pre-output level of the HEAD UNIT
connected with this unit.
NOTE
For the pre-output level, refer to the
<Specifications> in the instruction
manual of the HEAD UNIT.
The entire bandwidth is output without
filtering.
0Power indicator
When the power is turned on, the Power
indicator lights.
Ceci est un amplificateur à 4 canaux
avec deux amplificateurs stéréopho-
niques en un élément; l’un appelé
amplificateur A, l’autre amplificateur
B. Cet appareil est compatible avec
diverses configurations de chaîne,
simplement en sélectionnant les
positions des commutateurs et les
fonctions comme indiqué ci-après.
1Fusible (30 A)
REMARQUE
Si vous ne trouvezpas de fusible de
calibre adéquat dans le commerce, etc.,
contacter votre agent Kenwood.
2Borne BATT. (alimentation)
3Borne GND (masse)
4Borne P.CON (fil de commande
d’alimentation)
Commande l’unité ON/OFF.
REMARQUE
Commande l’unité d’alimentation.
Assurez-vous de le connecter à l’en-
semble des différents systèmes.
5Bornes SPEAKER OUTPUT (A.ch/B.
ch)
• Connexions stéréo:
Pour utiliser l’appareil comme amplifi-
cateur stéréo, des connections stéréo
doivent être utilisées. Les haut-parleurs
à connecter doivent avoir une impé-
dance de 2 ohms ou supérieure. Lorsque
plusieurs haut-parleurs doivent être
connectés, s’assurer que l’impédance
combinée soit de 2 ohms ou supérieure
pour chaque canal.
KAC-M3004KEnFrEs00.indd2 15/01/1510:33

Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.
Before calling service, first check the following table for possible problems.
PROBLEM POSSIBLE CAUSE SOLUTION
No sound.
(No sound from one
side.)
(Blown fuse.)
• Input (or output)cables are disconnected.
• Protection circuit may be activated.
• Volume is too high.
• The speaker cord is shorted.
• Connect the input (or output)cables.
• Check connections by referring to
<Protection function>.
• Replace the fuse and use lower volume.
• After check the speaker cord and fixing the
cause of the short, replace the fuse.
The output level is too
small (or too large).
• The input sensitivity adjusting control is
not set to the correct position. • Adjust the control correctly referring to <Controls>.
The sound quality is
bad.
(The sound is distorted.)
• The speakers wire are connected with
wrong ª/·polarity.
• A speaker wire is pinched by a screw in
the car body.
• The switches may be set improperly.
• Connect them properly checking the ª/·
of the terminals and wires well.
• Connect
the speaker wire again so that it is
not pinched by anything.
• Set switches properly by referring to
<Controls>.
Guide de dépannage
Ce qui peut apparaître comme un mauvais fonctionnement de votre appareil n’est peut-être que le résultat d’une
mauvaise opération ou d’une mauvaise connexion. Avant d’appeler un centre de service, vérifiez d’abord dans le
tableau suivant les problèmes possibles.
PROBLEME CAUSE POSSIBLE SOLUTION
Absence de sons.
(Pas de son d’un côté)
(Fusible grillé)
• Les câbles d’entrée (ou de sortie)sont
débranchés.
• Le circuit de protection peut être actionné.
• Le volume est trop fort.
• Les fils de raccordement d’enceinte sont en
court-circuit.
• Brancher les câbles d’entrée (ou de sortie).
• Vérifier les raccordements en se reportant au
paragraphe <Fonction de protection>.
• Remplacezle fusible et utilisezun niveau de
volume plus faible.
• Après avoir vérifié le câble d’enceinte et
réparé la cause du court-circuit, remplacezle
fusible.
Niveau de sortie trop
faible (ou trop fort).
• La commande de réglage de la sensibilité
d’entrée n’est pas amenée sur la bonne
position.
• Faire le réglage correctement en se reportant
aux indications données en <Contrôles>.
La qualité sonore est
manuvaise.
(Le son est distordu.)
• Les câbles de haut-parleur ont été
raccordés en inversant la polarité ª/·.
• Un câble de haut-parleur est pincé par une
vis dans le châssis de la voiture.
• Les commutateurs ne sont peut-être pas
positionnés comme il convient.
• Raccorder correctement en respectant les
indications ªet ·des bornes et des câbles.
• Rebrancher le câble de haut-parleur en
évitant tout pincement
• Positionner les commutateurs en tenant
compte des indications fournies aux
paragraphes <Contrôles>.
Guía sobre localización de averías
Lo que podría parecer una falla de funcionamiento de su unidad podría ser simplemente el resultado de un
pequeño error de operación o de un defecto de conexión. Antes de acudir al servicio, verifique primero el
siguiente cuadro sobre los problemas que se podrían presentar.
PROBLEMA CAUSA POSIBLE SOLUCION
No hay sonido.
(No hay sonido de un
lado.)
(Fusible fundido)
• Los cables de entrada (o salida)están
desconectados.
• El circuito de protección puede estar
activado.
• El volumen está demasiado alto.
• El cable del altavozestá cortocircuitado.
• Conecte los cables de entrada (o salida).
• Compruebe las conexiones consultando
<Función de protección>.
• Reemplace el fusible y utilice volumen bajo.
• Después de revisar el cable del altavoz
y arreglar la causa del cortocircuito,
reemplace el fusible.
El nivel de salida está
muy bajo (o muy alto)
• El control de ajuste de sensibilidad de
entrada no está en la posición correcta. • Ajuste bien el control consultando en <Controles>.
La calidad del sonido
es mala.
(El sonido está
distorsionado.)
• Los cables de los altavoces están
conectados con las polaridades ª/ ·
invertidas.
• Un cable de altavozestá pellizcado por un
tornillo de la carrocería del automóvil.
• Los conmutadores pueden estar mal
ajustados.
• Conéctelos correctamente asegurándose
bien de cuáles son los terminales ªy ·.
• Vuelva a conectar los cables de los altavoces
de forma que no queden pellizcados.
• Ponga bien los conmutadores consultando
<Controles>.
KAC-M3004KEnFrEs00.indd2 15/01/1510:33

Specifications
Specifications subject to change without notice.
Audio section
Rated power output (+B = 14.4V)
Stereo (4 Ω)................50 W × 4 (20 Hz– 20 kHz, ≤ 1.0 % THD)
Stereo (2 Ω).....................................75 W × 4 (1 kHz, ≤ 1.0 % THD)
Bridged (4 Ω)...............................150 W × 2 (1 kHz, ≤ 1.0 % THD)
Speaker impedance...............................4 Ω (2 Ω to 8 Ω allowable)
(Bridged connection: 4 Ω to 8 Ω allowable)
Frequency response (+0, –3 dB).............................20 Hz– 20 kHz
Input sensitivity (RCA)...........................................................0.2 V – 5.0 V
Signal to noise ratio .............................................................................87 dB
Input impedance...................................................................................10 kΩ
Low pass filter frequency (-12 dB/oct.)
.....................................................................50 Hz– 200 Hz(variable)
High pass filter frequency (-12 dB/oct.)
.....................................................................50 Hz– 200 Hz(variable)
General
Operating voltage................................14.4 V (11 – 16 V allowable)
Current consumption............................................................................21 A
Dimensions (W × H × D)......................................165 × 45 × 99 mm
6-1/2 × 1-3/4 × 3-7/8 inch
Weight....................................................................................0.76 kg (1.7 lbs)
CEA-2006 RMS Watts per channel @ 4 ohms, ≤ 1% THD+N
.....................................................................................50 W × 4
Signal to noise ratio
(Reference: 1Watt into 4 ohms)......................74 dBA
Spécifications
Les spécifications sont sujettes à changements sans
notification.
Section audio
Puissance de sortie norminale (+B = 14,4V)
Stéréo (4 Ω)................50 W × 4 (20 Hz– 20 kHz, ≤ 1,0 % THD)
Stéréo (2 Ω).....................................75 W × 4 (1 kHz, ≤ 1,0 % THD)
Pont (4 Ω)......................................150 W × 2 (1 kHz, ≤ 1,0 % THD)
Impédance d'enceinte.........................4 Ω (2 Ω à 8 Ω admissible)
(Connexions en pont: 4 Ω à 8 Ω admissible)
Réponse en fréquence (+0, –3 dB).........................20 Hz– 20 kHz
Sensibilité d'entrée (RCA)..................................................0,2 V – 5,0 V
Taux de signal/bruit.............................................................................87 dB
Impédance d’entrée............................................................................10 kΩ
Fréquence du filtre passe-bas (-12 dB/oct.)
.....................................................................50 Hz– 200 Hz(variable)
Fréquence du filtre passe-haut (-12 dB/oct.)
.....................................................................50 Hz– 200 Hz(variable)
Général
Tension de fonctionnement........14,4 V (11 – 16 V admissible)
Courant absorbé.......................................................................................21 A
Taille d’installation (L × H × P)..........................165 × 45 × 99 mm
6-1/2 × 1-3/4 × 3-7/8 pouce
Masse ......................................................................................0,76 kg (1,7 lbs)
CEA-2006
RMS Watts par channel @ 4 ohms, ≤ 1% THD+N
.....................................................................................50 W × 4
Taux signal/bruit
(référence : 1 Watt/4 ohms)...............................74 dBA
Especificaciones
Las especificaciones se encuentran sujetas a cambios
sin previo aviso.
Sección de audio
Salida de potencia nominal (+B = 14,4V)
Estereofónicas (4 Ω)...50 W × 4 (20 Hz– 20 kHz, ≤ 1,0 % de
distorsión armónica total)
Estereofónicas (2 Ω)........................75 W × 4 (1 kHz, ≤ 1,0 % de
distorsión armónica total)
Puenteada (4 Ω).............................. 150 W × 2 (1 kHz, ≤ 1,0 % de
distorsión armónica total)
Impedancia de altavoz...........................4 Ω (2 Ω a 8 Ω permitido)
(Conexiones en puente: 4 Ω a 8 Ω permitido)
Respuesta de frecuencia (+0, –3 dB).....................20 Hz– 20 kHz
Sensibilidad de entrada (RCA)........................................0,2 V – 5,0 V
Relación señal a ruido.........................................................................87 dB
Impedancia de entrada .....................................................................10 kΩ
Frecuencia del filtro pasa bajos (-12 dB/octava)
.....................................................................50 Hz– 200 Hz(variable)
Frecuencia del filtro pasa altos (-12 dB/octava)
.....................................................................50 Hz– 200 Hz(variable)
General
Tensión de funcionamiento
....................................14,4 V (margen de 11 – 16 V permitido)
Consumo.......................................................................................................21 A
Tamaño de instalación (Anch × Alt × Prof )
........................................................................................
165 × 45 × 99 mm
6-1/2 × 1-3/4 × 3-7/8 pulgada
Peso.....................................................................................0,76 kg (1,7 libras)
CEA-2006
Vatios RMS por canal @ 4 ohms, ≤ 1 % de
distorsión armónica total + N
.....................................................................................50 W × 4
Relación señal a ruido
(referencia: 1 vatio en 4 ohmios)....................74 dBA
KAC-M3004KEnFrEs00.indd2 15/01/1510:33