Kenwood CO600 series User manual

Your Kenwood Can Opener can be used to open a variety of domestic
can shapes and sizes. In addition the CO600 Series incorporates a
bottle opener and a knife sharpening facility.
When using electrical appliances basic safety precautions should
always be followed, including the following:-
1. Read all instructions.
2. This appliance is not intended for use by young children or infirm
persons without supervision.
3. Do not immerse appliance, cord or plug in water or other liquid.
4. Do not use the appliance if it is damaged.
5. Unplug the appliance from the mains supply
- before cleaning
- immediately after use
6. Do not use the appliance for other than its intended use.
7. This appliance is for domestic use only.
8. Young children should be supervised to ensure that they do not
play with this appliance.
KEEP THESE INSTRUCTIONS
IMPORTANT SAFEGUARDS
Know your Table Top Can Opener
1. Bottle Opener 5. Cutter Blade
2. Drive Wheel 6. Guide Pin
3. Magnet 7. Knife Sharpener
4. Lever 8. Cord Stowage
Key
1. Plug the appliance into the power
supply.
2. Lift the lever to the open position.
3. Hold the can with the top rim resting
under the metal guide pin and the can
resting on the drive wheel (Fig. 1).
4. Press the lever lightly down to start the
motor. The self-starting blade will then
pierce the can and commence cutting
(Fig. 2).
5. The can will be held fixed in position
with the magnet resting against the lid.
Large or wide cans may require extra
support from the user.
6. Once the can is open, the motor will
automatically stop, retaining the can and
lid safely in place.
7. To remove, lift the lever whilst holding
the can.
8. With the exception of aluminium cans,
the lid will be retained by the magnet
(Fig. 3).
9. For tidiness, any unwanted length of
cord can be stowed inside the
appliance.
10. Do not use the appliance to open ring-
pull cans.
Using your Table Top Can Opener
Connecting to Power
Before switching on make sure that the voltage of your electricity
supply is the same as that indicated on the underside of your can
opener.
IMPORTANT (UK ONLY): The wires in the mains lead are coloured
in accordance with the following code:
BLUE NEUTRAL
BROWN LIVE
NOTE:
This can opener complies with European Economic Community Radio
Interference Directive 89/336/EEC.
Fig. 1
Fig. 2
KENWOOD
Fig. 3
KENWOOD









When opening tall bottles, the unit should be
used towards the edge of a work top.
1. Position the bottle with the cap under the
front rim of the bottle opener.
2. Push down the bottle to remove the cap
whilst steadying the unit with one hand.
1. With the can opener sideways on, place
the knife into one of the recesses.
2. Gradually draw it towards yourself. Then
place the knife in the other recess and
repeat. Take care not to allow the knife to
cut into the body of the can opener.
3. Repeat this cycle several times in order
to sharpen the knife satisfactorily.
NOTE: Knives without a serrated edge,
preferably carbon steel are most suitable for
sharpening.
1. Disconnect the appliance by switching off
and removing the plug from the power
supply.
2. Lift the lever fully and withdraw the
assembly from the can opener.
3. Wash the lever in hot sudsy water and
dry thoroughly. Dishwasher is not
advised.
4. Replace the lever in the body
5. Wipe over the body with a damp cloth
and dry thoroughly.
Cleaning
Using the Knife Sharpener
Using the Bottle Opener
LIMITED
New Lane • Havant • Hants • PO9 2NH
www.kenwood.co.uk 10203/2
CO600 series
KENWOOD
KENWOOD
If the cord of this appliance is damaged it must, for safety reasons, be
replaced by Kenwood or an authorised Kenwood repairer.
UK
If you need help with:
using your can opener or servicing or repairs (in or out of guarantee)
call Kenwood on 023 9239 2333. Have your model number ready, it is
on the underside of your can opener.
EIRE
Contact local repairer from advertisement in GOLDEN PAGES.
ALL OTHER MARKETS
Contact the dealer from whom you purchased your appliance.
Service
KENWOOD
KENWOOD