Kenwood KNA-DV3100 User manual

KNA-DV3100
DVD NAVIGATION SYSTEM
INSTALLATION MANUAL
© PRINTED IN JAPAN B54-4407-00/00 (K) (DT)
KNA-DV3100Inst(K)_En 03.5.8 10:06 AM Page 1

2-English
Safety precautions
To prevent injury or fire, take the
following precautions:
•Insert the unit all the way in until it is fully
locked in place. Otherwise it may fall out of
place when jolted.
•When extending the ignition, battery, or ground
wires, make sure to use automotive-grade
wires or other wires with a 0.75mm2(AWG18)
or more to prevent wire deterioration and
damage to the wire coating.
•To prevent a short circuit, never put or leave
any metallic objects (such as coins or metal
tools) inside the unit.
•If the unit starts to emit smoke or strange
smells, turn off the power immediately and
consult your Kenwood dealer.
To prevent damage to the machine, take
the following precautions:
•Make sure to ground the unit to a negative 12
V DC power supply.
•Do not open the top or bottom covers of the
unit.
•Do not install the unit in a spot exposed to
direct sunlight or excessive heat or humidity.
Also avoid places with too much dust or the
possibility of water splashing.
•Do not subject the faceplate to excessive
shock, as it is a piece of precision equipment.
•When replacing a fuse, only use a new one
with the prescribed rating. Using a fuse with
the wrong rating may cause your unit to
malfunction.
•To prevent short circuits when replacing a fuse,
first disconnect the wiring harness.
•Do not use your own screws. Use only the
screws provided. If you use the wrong screws,
you could damage the unit.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it
with a dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain
off with a cloth moistened with neutral cleaner,
then wipe neutral detergent off.
Applying spray cleaner directly to the unit may
affect its mechanical parts. Wiping the
faceplate with a hard cloth or using a volatile
liquid such as thinner or alcohol may scratch
the surface or erases characters.
Lens Fogging
Right after you turn on the car heater in cold
weather, dew or condensation may form on
the lens in the DVD player of the unit. Called
lens fogging, DVDs may be impossible to play.
In such a situation, remove the disc and wait
for the condensation to evaporate. If the unit
still does not operate normally after a while,
consult your Kenwood dealer.
2CAUTION
2CAUTION
2WARNING
KNA-DV3100Inst(K)_En 03.5.8 10:06 AM Page 2

Reset
When installation is complete, check the connections.
If everything is in order, press the reset button. If the
unit does not seem to be working right, try pressing
the reset button first.
If that does not solve the problem, consult your
Kenwood dealer.
The Mark Position of Your Car Immediately After Installation
•Immediately after installation, the information of the GPS satellite is taken in and it may take
several minutes to measure the position of the current location.
•Immediately after installation, the initial value setting of the gyro sensor is required. After
measuring the position of the current location, drive of about 6.2 mile (10 km) and further at a
constant speed at least 24.8 mile/h (40 km/h) in a place where there are few obstacles (for
example, buildings and tree-lined streets).
•Until the initial values are set, the position and speed indication of you car's mark on the navigation
system may differ greatly from the actual values.
•The proper connection of the car speed signal wire can be checked with the menu screen. Please
see the instruction manual for details.
NOTE
Installation Procedure
To prevent short circuits, remove the key from the ignition and disconnect the ·battery.
Make the proper input and output wire connections for each unit.
Connect the wiring harness wires in the following order: ground, battery, ignition.
Connect the wiring harness connector to the unit.
Install the unit in your car.
Reconnect the ·terminal of the battery.
Press the reset button.(See page 3)
6
6
5
4
3
2
1
•If your car's ignition does not have an ACC position, connect the ignition wires to a power source
that can be turned on and off with the ignition key. If you connect the ignition wire to a power
source with a constant voltage supply, as with battery wires, the battery may die.
•If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace
the old fuse with one with the same rating.
•Do not let unconnected wires or terminals touch metal on the car or anything else conducting
electricity. To prevent a short circuit, do not remove the caps on the ends of the unconnected
wires or the terminals.
•After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
•Insulate unconnected wires with vinyl tape or other similar material.
2CAUTION
English-3
KNA-DV3100Inst(K)_En 03.5.8 10:06 AM Page 3

Installation
■Accessories
■Installation for Navigation System
•Select for installation a location where the unit can be placed completely horizontal.
•Be sure to firmly stabilise this product. Do not install it in a location which is not stable.
2CAUTION
Check that there are no wiring cables or other parts beneath the floor mat before cutting the floor
mat.
2WARNING
4-English
A.........2D.........1B(M5X8mm).........4C(ø5X20mm).........4
E.........1H.........1F.........1G.........1
I.........1
Ø4
AB (M5x8mm)
C (Ø5x20mm)
Holes for attachment
Holes for suspension
and attachment
KNA-DV3100Inst(K)_En 03.5.8 10:06 AM Page 4

English-5
■Installation of the GPS Antenna
•GPS antenna Dcan be installed either inside or outside of the car, but either way it should be
installed as horizontally as possible to allow easy reception of the GPS satellite signals.
•The reception conditions of the GPS satellite will be less favorable with installation inside the car
as compared to outside the car. Depending on the type of car, reception of the GPS satellite signals
might not be possible with an inside installation. Installation outside of the car is recommended if
circumstances allow.
•The GPS antenna should be installed at a position that is spaced at least 12 inch (30 cm) from
cellular phone or other transmitting antennas. Signals from the GPS satellite may be interfered with
by these types of communication.
•Do not remove the tape from the back of the GPS antenna. When the tape comes off, the
waterproof effectiveness is diminished and this may cause a fault in the GPS antenna.
•Painting the GPS antenna with (metallic) paint may cause a drop in performance.
2CAUTION
●Installation Outside the Car
Installation to the trunk lid is made with the GPS
antenna Dbuilt-in magnet.
1Affix the waterproof pad that accompanies Eat the
place that comes up against the waterproof rubber
lining the trunk.
2Draw the cable of Dfrom the trunk lid into the trunk.
●Installation Inside the Car
Install at a place close to the window surface at the
center of the rear tray or on the inside of the rear
window to allow easy reception of the GPS satellite
signals.
1Peel off the release paper of Fand affix to
placement position of D.
2Place Don F.
D
E
D
F
KNA-DV3100Inst(K)_En 03.5.8 10:06 AM Page 5

Connection
PRK SW
S SENS
Wiring harness G
Parking sensor wire (Green)
To parking brake detection switch harness of car
Car speed signal intermediate wire H(White)
To the car speed signal harness
For the sake of safety, be sure to
connect the parking sensor wire.
2WARNING
Car speed signal wire (White)
D
S SENS
Remote Control Sensor
accompanying the Remote
Control
Audio Output (MONO) (Black)
Visual Output (Yellow)
6-English
(3A)
(5A)
•Do not cut off the holder marked "S SENS" (containing a
protection diode) of the car speed signal detection wire H
(White). Doing so will cause a fault with the car.
•Please contact your dealer for information about the connection
method. A connection error will lead to car breakdown.
2WARNING
When disconnecting the interface cable, pinch and pull
the ring of the connector. If you pull other parts of the
connector, the locking mechanism of the connector is
not released, which may damage the connector.
2CAUTION
I/F Cable I
To the monitor unit
("NAV I/F" terminal)
Voice control microphone (Optional)
Do not remove the cap when
not connecting the cable.
NOTE
KNA-DV3100Inst(K)_En 03.5.8 10:06 AM Page 6

REVERSE
TEL MUTE
ILLUMI
Automatic illumination control wire (Orange)
Ignition wire (Red) 12 V
Battery wire (Yellow) 12 V
Ground wire (Black) -(To car chassis)
Car fuse box
ACC Ignition key switch
To car light control switch
Car fuse box
(Main fuse)
Battery
If no connections are made, do not let the wire
come out from the tab.
NOTE
TEL mute wire (Brown)
Connect to the TEL mute terminal
for the navigation system of the
KENWOOD car audio.
To reverse lamp harness of car
Reverse detection wire (Pink)
English-7
A)
)
Attaching Remote Control Sensor
When using a TV monitor other than ones
manufactured by KENWOOD, attach the Remote
Control Sensor following the procedure below:
Backing paper
Double-sided
tape
1Remove the backing paper from the double-sided
tape and attach the tape to the back of the
Remote Control Sensor.
2After wiping off the dirt or oil from the attachment
location, attach the Remote Control Sensor.
•Wipe off the dirt or oil from the surface to which
the Sensor is attached.
•Avoid locations under direct sunlight or near the TV
monitor where signals from the remote controller
are not received easily.
NOTE
KNA-DV3100Inst(K)_En 03.5.8 11:37 AM Page 7

KNA-DV3100Inst(K)_En 03.5.8 10:16 AM Page 8