Keurig Eccellenza touch User manual

1
ECCELLENZA TOUCH™CLEANING & STARTUP PROCEDURE
This procedure demonstrates how to properly clean
and sanitize the Eccellenza Touch™brewer
This procedure should take approximately 60 minutes
Tools Needed
 Keurig®Bean to Cup Deep Cleaning kit (if available)
 Large bucket or container
 Available sink
 Slotted screwdriver
 Key to main door
 Small paint brush

2
Table of Contents

Disconnecting & Draining ………………………………………………. Pg. 3
Removing the Brewer Assembly ………………………………………. Pg. 4
Removing the Coffee Hopper ………………………………………….. Pg. 5
Removing the Powder System ………………………………………… Pg. 6 - 9
Cleaning & Sanitizing Procedure ……………………………………… Pg. 10
Cleaning Interior & Exterior Components …………………………….. Pg. 11
Reinstalling the Powder System ………………………………………. Pg. 12
Reinstalling the Brewer Assembly …………………………………….. Pg. 13
Reinstalling the Coffee Hopper ………………………………………… Pg. 14
Restarting & Refilling ……………………………………………………. Pg. 15
How to Perform Both Cleanings & Rinses ……………………………. Pg.'s 16 - 20
Performing Test Brews ………………………………………………….. Pg. 21
Note: Cleaning: Refers to generally wiping down/removing debris or spills from surfaces.
Sanitization: Refers to using a disinfecting solution, wipe, or a cloth with disinfectant on it
to help eliminate contaminants and germs.

3
Disconnecting & Draining


Turn power switch to O position and unplug
from grounded outlet.
Turn machine around to access back cover and
remove 4 screws and lift back cover up and
away from machine.
Note: Water supply may need to be disconnected to
achieve above step.
Locate drain hose, open valve, drain hot water
into a large bucket or water-tight container then
close valve and restow.
Replace back panel with the 4 screws.
Note: Ensure back panel lower tabs are
inserted correctly.
CAUTION
WATER MAY BE VERY HOT
Shown with factory installed tape

4
Removing the Brewer Assembly
 

Turn machine back around to front.
Remove waste container, empty & clean.
Insert key and turn counterclockwise then open
main door.
Remove coffee spout from
front of brewer assembly.
Remove brewer assembly by
pressing red button and turning
to the clockwise while lifting.
Carefully remove wiper and
thoroughly clean exterior of
both parts.
NOTE: Brewer assembly cleaning
instructions can be found on page
17.

5
Removing the Coffee Hopper


LOOSEN ONLY the two screws beneath the coffee hopper.
Lift coffee hopper from unit and remove.
If necessary, discard coffee beans and wipe down or thoroughly clean.
NOTE: See cleaning instructions on page 11.

6
Removing the Powder System




Disconnect hoses to mixing chambers. Unlock and remove mixing chambers.
Remove mixing disks by sliding forward from
the whipper motor shaft.
Remove locking rings.

7
Removing the Powder System cont.




Grab and pull towards you to remove powder
drawer.
Lift powder lid.
Remove powder hopper caps. Carefully remove powder hopper liner.

8
Removing the Powder System cont.


Disconnect hot water hose and all hoses.
Clean and sanitize all removed powder system parts in
accordance with the Cleaning & Sanitizing procedure on page 11.
NOTE: We recommend cleaning and sanitizing all parts with Urnex®products from
the Keurig®Bean to Cup Deep Cleaning Kit, but comparable agents may also be
used

9
Removing the Powder System cont.


Remove and empty powder hoppers.
NOTE: If needed, hoppers can be disassembled (shown below) then cleaned
and sanitized following instructions on page 11.
Otherwise they can just be refilled following instructions on page 21.

10
Cleaning Interior & Exterior Components

Wipe interior area around the brewer motor
and powder system with a clean cloth dipped
in Urnex®Complete Café sanitizer.
NOTE: If available, Urnex®Café Wipz can be used.
Remove and wipe down or clean cup stand &
grill using cleaning instructions on page 11.
We recommend using the Urnex®Complete Café solution noted on Page 11 on all external
surfaces ONLY. But any household or commercial certified disinfectant wipe can be used
(following manufacturer's instructions).