keylitos Electric Bug Zapper User manual
Keylitos
Electric Bug Zapper
Please read these instructions before using the Keylitos Electric
Bug Zapper and keep for future reference.
-1-
Keylitos electric bug zapper is designed to kill mosquitoes, flies,
moths, and other flying insects. It uses high-power UVA lamps to
attract insects with their perception of light and entrap insects
with the grid of high voltage effectively, high electric field inside
can kill insects immediately. The UVA light is harmless to human
bodies and pets, with no chemicals involved. This product is ideal
for indoor and outdoor use, such as homes, hotels, restaurants,
shops, warehouses, corridors, gardens, etc.
Working Principle:
1. Shell material: ABS
2. Operating voltage: 100-120V~60Hz (US)
3. Voltage of grid: 4200V
4. Bulb wattage: 18W (Replaceable UVA bulb)
5. Have an on/off switch
6. Model number: LG-361-28W
7. Waterproof level: IPX4
8. Package list: Bug zapper with 2 meters power cable, Hanging
chain, Cleaning brush.
Specification:
1. The bug zapper is free-standing. Moreover, it’s
equipped with a hanging chain and can be
hung on the wall.
2. The package includes a catcher tray which
allows for free-standing placement without a
mess.
3. Self-cleaning vertical grid allows dead bugs to
drop straight down into the removable catcher
tray. And the brush can easily clean the insects.
Features:
1. Do not touch the high voltage grids with fingers or metal when
the product works.
2. Do not use metal and other conductors for cleaning.
3. This is electric equipment, please don’t keep it in water
4. Please keep the machine away from children.
5. Keep away from flammable and explosive places.
Warning:
1. Take the product from the package, and check if it is damaged
before use. If it’s damaged, please feel free to contact Keylitos
2. Lay it flat on the table or hang it on the wall.
3. Connect it with the correct power socket, and switch on. When
the tube is lighting, it is working normally.
qualified electrician for advice.
How to Use:
1.Be sure to disconnect the power supply for the removal of
insect corpses or maintenance.
How to Clean:
1.Place or hang the bug zapper 1.5-2 meters above the ground
and do not place it near a fan and other places with strong air
currents.
2.Turn off the lights to provide a dark environment for the best
effect and close the doors and windows if it’s for indoor use.
3.Please turn on the Bug Zapper 2-3 hours before entering the
room.
4.Please clean the device regularly.
How to Get Most Out of the Insects Killer
Note: If you want to clean the Bug zapper thoroughly, please
disconnect the power supply and discharge the mesh
grid with an insulated screwdriver.
-2-
3. Use the brush to clean the dead insect from the product.
4. Remove the screw, rotate the bottom tray counterclockwise
and open it, then pour the dead insect into the trash. Then you
can rotate the bottom tray clockwise to install it.
5. Please rinse it down with water if there are insect corpses left
and use it after the machine dries.
Note:- Do not rinse the machine upside down, it will cause water
accumulation on the top circuit board and the Bug zapper
will be damaged.
- Please remove the bottom tray before rinsing.
- The bulb can be pulled out for clean and replacement.
Do not splash water on the top connectors of the lamp.
OFFON
-4-
Failures
Bulb does not light and no
high voltage on grid
Possible Causes Solutions
Troubleshooting
1.No electrical power
2.Lamp not seated properly
3.Starter defective
4.Burned-out bulb
1.Check fuse or circuit
breaker
Check extension cord
2.Check all sockets for
proper seating and
alignment
3.Starter replacement by
manufacturer required
4.Replace the bulb
Bulb is on, but no high
voltage on grid
1.Shorted grids
2.Transformer defective
1.Examine killing grid for
material build-up
Clean grid using an air
blower
2.Replace by
manufacturer required
Intermittent or continuous
sparking between
1.Gap between grid rods is
too small
2.Grid clogged with foreign
material
1.Unplug unit and adjust
grids by bending back
into alignment. grid rods
2.Clean grid using an air
blower
Bulb is on, but no longer
attracts insects
Note:The above solutions are for the reference of professionals only.
1.Invisible black light output
reduced due to bulb age
1.Replace bulb. Consult
seller to get the
replacement
-5-
1.The warranty period for the device is two years from the date of
delivery.
2.Incorrect use and man-made damages are excluded under the
warranty.
3.Please download the PDF manual on the below website:
https://www.keylitos.com/downloads
Guarantee
1. Disconnect unit from electric source.
2. Depress latch and remove plastic bulb retainer at base of unit
as shown.
3. Bulb can now be pulled down out of its socket.
4. Insert replacement bulb into socket.
5. Replace plastic bulb retainer and secure latch.
Bulb Replacement
This device complies with part 15 of the FCC Rules.
Customer Service
Install
Pull out
Table of contents
