Keysight M9187A User guide

Keysight M9187A
PXI Digital IO Module
Startup Guide

Notices
© Keysight Technologies, Inc. 2014
No part of this manual may be repro-
duced in any form or by any means
(including electronic storage and retrieval
or translation into a foreign language)
without prior agreement and written con-
sent from Keysight Technologies, Inc. as
governed by United States and interna-
tional copyright laws.
Manual Part Number
M9187-90001
Edition
Third Edition, December 2014
Published in U.S.A.
900 S. Taft Avenue,
Loveland, CO. 80537
Trademarks
PICMIG®, COMPACT PCI®, and Advanced
TCA®are registered trademarks of the
PCI Industrial Computer Manufacturers
Group
PCI-SIG®, PCI Express®, and PCIe®are
registered trademarks of PCI-SIG
Sales and Technical Support
To contact Keysight for sales and techni-
cal support, refer to the support links on
the following Keysight websites:
www.keysight.com/find/M9187A (prod-
uct-specific information and support,
software and documentation updates)
www.keysight.com/find/assist (world-
wide contact information for repair and
service)
Declaration of Conformity
Declarations of Conformity for this prod-
uct and for other Keysight products may
be downloaded from the Web. Go to
http://www.keysight.com/go/conformity
and click on “Declarations of Conformity.”
You can then search by product number
to find the latest Declaration of Confor-
mity.
Technology Licenses
The hardware and/or software described
in this document are furnished under a
license and may be used or copied only in
accordance with the terms of such
license.
Warranty
THE MATERIAL CONTAINED IN THIS
DOCUMENT IS PROVIDED “AS IS,” AND
IS SUBJECT TO BEING CHANGED,
WITHOUT NOTICE, IN FUTURE EDI-
TIONS. FURTHER, TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE
LAW, KEYSIGHT DISCLAIMS ALL WAR-
RANTIES, EITHER EXPRESS OR IMPLIED,
WITH REGARD TO THIS MANUAL AND
ANY INFORMATION CONTAINED
HEREIN, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. KEYSIGHT
SHALL NOT BE LIABLE FOR ERRORS OR
FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES IN CONNECTION WITH THE
FURNISHING, USE, OR PERFORMANCE
OF THIS DOCUMENT OR OF ANY INFOR-
MATION CONTAINED HEREIN. SHOULD
KEYSIGHT AND THE USER HAVE A SEP-
ARATE WRITTEN AGREEMENT WITH
WARRANTY TERMS COVERING THE
MATERIAL IN THIS DOCUMENT THAT
CONFLICT WITH THESE TERMS, THE
WARRANTY TERMS IN THE SEPARATE
AGREEMENT SHALL CONTROL.
Keysight Technologies does not warrant
third-party system-level (combination of
chassis, controllers, modules, etc.) per-
formance, safety, or regulatory compli-
ance unless specifically stated.
DFARS/Restricted Rights
Notices
If software is for use in the performance
of a U.S. Government prime contract or
subcontract, Software is delivered and
licensed as “Commercial computer soft-
ware” as defined in DFAR 252.227-7014
(June 1995), or as a “commercial item” as
defined in FAR 2.101(a) or as “Restricted
computer software” as defined in FAR
52.227-19 (June 1987) or any equivalent
agency regulation or contract clause.
Use, duplication or disclosure of Software
is subject to Keysight Technologies’ stan-
dard commercial license terms, and non-
DOD Departments and Agencies of the
U.S. Government will receive no greater
than Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S. Gov-
ernment users will receive no greater
than Limited Rights as defined in FAR
52.227-14 (June 1987) or DFAR 252.227-
7015 (b)(2) (November 1995), as applica-
ble in any technical data.

Safety Information
The following general safety precau-
tions must be observed during all
phases of operation of this instrument.
Failure to comply with these precau-
tions or with specific warnings or oper-
ating instructions in the product
manuals violates safety standards of
design, manufacture, and intended use
of the instrument. Keysight Technolo-
gies assumes no liability for the cus-
tomer's failure to comply with these
requirements.
General
Do not use this product in any manner not
specified by the manufacturer. The protec-
tive features of this product must not be
impaired if it is used in a manner specified in
the operation instructions.
Before Applying Power
Verify that all safety precautions are taken.
Make all connections to the unit before
applying power. Note the external markings
described under “Safety Symbols”.
Ground the Instrument
Keysight chassis’ are provided with a
grounding-type power plug. The
instrument chassis and cover must be
connected to an electrical ground to
minimize shock hazard. The ground pin
must be firmly connected to an electri-
cal ground (safety ground) terminal at
the power outlet. Any interruption of
the protective (grounding) conductor
or disconnection of the protective
earth terminal will cause a potential
shock hazard that could result in per-
sonal injury.
Do Not Operate in an Explosive
Atmosphere
Do not operate the module/chassis in
the presence of flammable gases or
fumes.
Do Not Operate Near Flammable
Liquids
Do not operate the module/chassis in
the presence of flammable liquids or
near containers of such liquids.
Cleaning
Clean the outside of the Keysight mod-
ule/chassis with a soft, lint-free,
slightly dampened cloth. Do not use
detergent or chemical solvents.
Do Not Remove Instrument Cover
Only qualified, service-trained person-
nel who are aware of the hazards
involved should remove instrument
covers. Always disconnect the power
cable and any external circuits before
removing the instrument cover.
Keep away from live circuits
Operating personnel must not remove
equipment covers or shields. Proce-
dures involving the removal of covers
and shields are for use by service-
trained personnel only. Under certain
conditions, dangerous voltages may
exist even with the equipment
switched off. To avoid dangerous elec-
trical shock, DO NOT perform proce-
dures involving cover or shield removal
unless you are qualified to do so.
DO NOT operate damaged
equipment
Whenever it is possible that the safety
protection features built into this prod-
uct have been impaired, either through
physical damage, excessive moisture,
or any other reason, REMOVE POWER
and do not use the product until safe
operation can be verified by service-
trained personnel. If necessary, return
the product to an Keysight Technolo-
gies Sales and Service Office for ser-
vice and repair to ensure the safety
features are maintained.
DO NOT block the primary
disconnect
The primary disconnect device is the
appliance connector/power cord when
a chassis used by itself, but when
installed into a rack or system the dis-
connect may be impaired and must be
considered part of the installation.
Do Not Modify the Instrument
Do not install substitute parts or per-
form any unauthorized modification to
the product. Return the product to an
Keysight Sales and Service Office to
ensure that safety features are main-
tained.
In Case of Damage
Instruments that appear damaged or
defective should be made inoperative
and secured against unintended oper-
ation until they can be repaired by
qualified service personnel
Do NOT block vents and fan exhaust:
To ensure adequate cooling and venti-
lation, leave a gap of at least 50mm
(2") around vent holes on both sides of
the chassis.
Do NOT operate with empty slots: To
ensure proper cooling and avoid dam-
aging equipment, fill each empty slot
with an AXIe filler panel module.
Do NOT stack free-standing chassis:
Stacked chassis should be rack-
mounted.
All modules are grounded through the
chassis: During installation, tighten
each module's retaining screws to
secure the module to the chassis and
to make the ground connection.
Operator is responsible to maintain
safe operating conditions. To ensure
safe operating conditions, modules
should not be operated beyond the full
temperature range specified in the
Environmental and physical specifica-
tion. Exceeding safe operating condi-
tions can result in shorter lifespan,
improper module performance and
user safety issues. When the modules
are in use and operation within the
specified full temperature range is not
maintained, module surface tempera-
tures may exceed safe handling condi-
tions which can cause discomfort or
burns if touched. In the event of a
module exceeding the full temperature
range, always allow the module to cool
before touching or removing modules
from the chassis.
iv

Safety Symbols
A CAUTION denotes a hazard. It
calls attention to an operating pro-
cedure or practice, that, if not cor-
rectly performed or adhered to
could result in damage to the
product or loss of important data.
Do not proceed beyond a CAUTION
notice until the indicated condi-
tions are fully understood and met.
A WARNING denotes a hazard. It
calls attention to an operating pro-
cedure or practice, that, if not cor-
rectly performed or adhered to,
could result in personal injury or
death. Do not proceed beyond a
WARNING notice until the indi-
cated conditions are fully under-
stood and met.
Products display the following sym-
bols:
The instrument has been tested,
investigated and found to comply with
the requirements of the Standard(s) for
Electrical Measuring & Test Equip-
ment.
Notice for European Community: This
product complies with the relevant
European legal Directives: EMC Direc-
tive (2004/108/EC) and Low Voltage
Directive (2006/95/EC).
This is the symbol for an Industrial,
Scientific, and Medical Group 1 Class A
product.
The Regulatory Compliance Mark
(RCM) mark is a registered trademark.
This signifies compliance with the Aus-
tralia EMC Framework regulations
under the terms of the Radio Commu-
nication Act of 1992.
ICES/NMB-001 indicates that this ISM
device complies with the Canadian
ICES-001.
This symbol represents the time period
during which no hazardous or toxic
substance elements are expected to
leak or deteriorate during normal use.
Forty years is the expected useful life
of this product.
Waste Electrical and
Electronic
Equipment (WEEE)
Directive
2002/96/EC
This product complies with the WEEE
Directive (2002/96/EC) marking
requirement. The affixed product label
(see below) indicates that you must not
discard this electrical/electronic prod-
uct in domestic household waste.
Product Category: With reference to
the equipment types in the WEEE
directive Annex 1, this product is clas-
sified as a “Monitoring and Control
instrumentation” product.
Do not dispose in domestic household
waste.
To return unwanted products, contact
your local Keysight office, or see
www.keysight.com/environment/prod-
uct for more information.
Warning, risk of electric
shock
Refer to manual for addi-
tional safety information.
Earth Ground.
Chassis Ground.
Alternating Current (AC).
Standby Power. Unit is not
completely disconnected
from AC mains when
switch is in standby.
Antistatic precautions
should be taken.
For localized Safety Warnings, Refer
to Keysight Safety document (p/n
9320-6792).
ICES/NMB-001
ISM GRP 1-A
v

vi

Keysight M9187A PXI Digital IO Module Startup Guide vii
Contents
Keysight PXI Digital IO Module Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Related documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 1: Unpack and Inspect the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Inspect for damage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Return the module for service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step 2: Verify Shipment Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Step 3: Install the Software on the Host Computer . . . . . . . . . . . . . . . . . . . . . 12
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PXI System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power the controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Install Keysight IO Libraries Suite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Install instrument drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Step 4. Connect the Controller to the PXI Chassis. . . . . . . . . . . . . . . . . . . . . . 16
Using a remote PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using an embedded computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 5: Install the Module in the PXI Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . 17
Step 6. Verify Operation of the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Run Keysight IO Libraries Connection Expert . . . . . . . . . . . . . . . . . . . . . . . 19
Verify operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Module Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Module Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Module Front Panel, Connector and Pin Out. . . . . . . . . . . . . . . . . . . . . . . . 23
M9187A Module Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Y1181A 78 Pin Shielded Connector Block. . . . . . . . . . . . . . . . . . . . . . . . . . 26
Y1187A, Y1188A 78 Pin Male to Female Connector Cable. . . . . . . . . . . . . 27
Disassembling the Connector Block Clam Shells . . . . . . . . . . . . . . . . . . . . 28
Electrical Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Transients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
High Energy Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Electrical Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

viii Keysight M9187A PXI Digital IO Module Startup Guide

M9187A PXI Digital IO Module
Startup Guide
9
Keysight PXI Digital IO Module Introduction
The Keysight M9187A PXI Digital IO Module provides 32 high output voltage and
current channels along with 32 dual variable threshold input channels.
-Each of the output channels can drive the output either high (sourcing up to
0.4A) or low (sinking up to 0.5A), or three-stated (off ). All output channels are
protected against over-voltage, over-current, and thermal overload. An
external power supply is required for high-side driving.
-The 32 input channels are read by comparing the input DC voltage to two
threshold voltages that can be set between 0.3 and 50Vdc. The thresholds
can programmatically be set with 12.5mVdc resolution, permitting input
testing against the system thresholds that define a logic low or logic high.
Note that the two thresholds are the same for all 32 input channels -- the
thresholds are not independently set for each input channels.
-The inputs can be connected directly to the outputs without risk of damage,
allowing module configuration for operation as 32 channels of independent
input and output or as 32 channels of configurable I/O.
-User connection is a 78 pin D-type connector on the module front panel.
Keysight also supplies software drivers allowing you to support the module in all
popular PXI chassis’ and programming environments. Soft Front Panel software
allows you to exercise the channels for test purposes.
For detailed usage instructions, refer to the M9187A Digital Soft Front Panel help
file on the Digital IO Module Software and Product Information CD.
Related documentation
This Startup Guide, and the documentation listed below, are on the Digital IO
Module Software and Product Information CD.
-Help file for the Digital IO Module Soft Front Panel
-Help file for the Digital IO Module IVI-C/IVI-COM device drivers
-Help file for the Digital IO Module LabVIEW G device drivers
-Keysight PXI Digital IO Module Specifications. For the latest specifications,
check the Keysight web site at: www.keysight.com/find/pxi-dio.
Inputs to the Keysight M9187A module are DC voltage
only.

10 Keysight M9187A PXI Digital IO Startup Guide
Step 1: Unpack and Inspect the Module
Step 1: Unpack and Inspect the Module
ESD
Electrostatic discharge (ESD) can damage or destroy electronic components. All
work on electronic assemblies should be performed at a static-safe work station.
The following figure shows an example of a static-safe work station using two
types of ESD protection.
-Conductive table-mat and wrist-strap combination.
-Conductive floor-mat and heel-strap combination.
Both types, when used together,
provide a significant level of ESD
protection. Of the two, only the
table-mat and wrist-strap
combination provides adequate
ESD protection when used alone.
To ensure user safety, the
static-safe accessories must
provide at least 1 Mof isolation
from ground. Purchase
acceptable ESD accessories from
your local supplier.
Keysight’s PXI Modules are shipped in materials that prevent
static electricity damage. The modules should only be removed
from the packaging in an anti-static area ensuring that correct
anti-static precautions are taken. Store all modules in anti-static
envelopes when not in use.

Keysight M9187A PXI Digital IO Startup Guide 11
Step 1: Unpack and Inspect the Module
Inspect for damage
After unpacking the module, carefully inspect it for any shipping damage. Report
any damage to the shipping agent immediately, as such damage is not covered
by the warranty.
Return the module for service
Should it become necessary to return a Keysight module for repair or service,
follow the steps below:
1Review the warranty information shipped with your product.
2Contact Keysight to obtain a return authorization and return address. If you
need assistance finding Keysight contact information go to
www.keysight.com/find/assist (worldwide contact information for repair and
service) or refer to the Support information on the product web page at:
www.keysight.com/find/pxi-dio.
3Write the following information on a tag and attach it to the malfunctioning
equipment.
–Name and address of owner. A Post Office box is not acceptable as a return
address.
–Product model number (M9187A).
–Product serial number (for example, MYXXXXXXXX). The serial number
label is located on the side of the module.
–A description of failure or service required.
4Carefully pack the module in its original ESD bag and carton. If the original
carton is not available, use bubble wrap or packing peanuts, place the
instrument in a sealed container and mark the container “FRAGILE”.
5On the shipping label, write ATTENTION REPAIR DEPARTMENT and the
service order number (if known).
To avoid damage when handling a module; do not touch exposed
connector pins.
If any correspondence is required, refer to the product by serial
number and model number.

12 Keysight M9187A PXI Digital IO Startup Guide
Step 2: Verify Shipment Contents
Step 2: Verify Shipment Contents
Your shipment should have included the following:
-The Keysight PXI M9187A Digital IO module that you ordered.
-This document (Keysight PXI M9187A Module Startup Guide).
-A Digital IO Module Software and Product Information CD. This CD contains
software, drivers and all product printed documentation in PDF format for the
PXI Digital IO Module.
-An Automation-Ready CD with Keysight IO Libraries Suite (version 16.0 or
later).
-Any other accessories that you ordered (cables, connectors, etc.).
Step 3: Install the Software on the Host Computer
The following illustration shows typical system installations.
Controller:
System Interface:
PXI System Chassis:
M9018A
18 Slot PXIe Chassis
M9021
Cable Interface
Module
Y1200A
PCIe Cable
M9045
PCIe Laptop
Adapter
Laptop PC
Y1202A
PCIe Cable
M9047
PCIe Desktop
Adapter
Desk mount or
Rack mount PC
PXIe Embedded
System Controller
Do not install the PXI modules in the PXI chassis yet! You must
install the software prior to installing the modules in the chassis
so that Keysight IO Libraries Connection Expert finds them.

Keysight M9187A PXI Digital IO Startup Guide 13
Step 3: Install the Software on the Host Computer
System requirements
The following table lists the minimum system requirements for Keysight IO
Libraries Suite 16. In general, any x86 or x64 (except Itanium) should work but
there may be a significant decrease in performance.
PXI System
Operating
System
Windows XP Service Pack 3 or
later
Windows Vista SP1 and SP2
(32-bit and 64-bit), Business,
Ultimate, Enterprise, Home
Basic, and Home Premium
Windows 7 (32- and 64-bit)
Starter, Home Basic, Home
Premium, Professional,
Ultimate, Enterprise
Processor
Speed
600 MHz or higher required,
800 MHz recommended
1Ghz 32-bit (x86),
1GHz 64-bit (x64),
no support for Itanium64
1Ghz 32-bit (x86),
1GHz 64-bit (x64),
no support for Itanium64
Available
memory
256 MB minimum
(1 GB or greater
recommended)
1 GB minimum 1 GB minimum
Available
hard disk
space*
1.5 GB available hard disk
space, includes:
•1GB available for Microsoft
.NET Framework 3.5 SP1†
•100MB for Keysight IO
Libraries Suite
1.5 GB available hard disk
space, includes:
•1GB available for Microsoft
.NET Framework 3.5 SP12
•100MB for Keysight IO
Libraries Suite
1.5 GB available hard disk
space, includes:
•1GB available for Microsoft
.NET Framework 3.5 SP12
•100MB for Keysight IO
Libraries Suite
Video Super VGA (800x600) 256
colors or more
Support for DirectX 9 graphics
with 128MB graphics memory
recommended (Super VGA
graphics is supported)
Support for DirectX 9 graphics
with 128MB graphics memory
recommended (Super VGA
graphics is supported)
Browser Microsoft Internet Explorer 6.0
or greater
Microsoft Internet Explorer 7
or greater
Microsoft Internet Explorer 7
or greater
* Because of the installation procedure, less memory may be required for operation than is required for installation.
† .NET Framework Runtime Components are installed by default with Windows Vista. Therefore you may not need this amount of
available disk space.
PXI system/ host
controller
A PXI or PXI Express embedded controller or PC host controller is
required.

14 Keysight M9187A PXI Digital IO Startup Guide
Step 3: Install the Software on the Host Computer
Power the controller
-If you are using a desktop, laptop, or rack mount PC as remote controller:
1Install any peripheral devices in the PC (e.g., PCIe Interface adapters, etc.).
Follow the manufacturers instructions.
2Power up the controller. Do not apply power to the PXI chassis yet.
3Choose the default option for any “Found Hardware” dialogs.
-If you are using a PXI embedded computer as the host computer:
1Install the embedded computer module into the PXI chassis following the
manufacturers instructions.
2Connect peripherals such as a mouse, keyboard, monitor, CD drive, etc.
3Power up the chassis.
4Choose the default option for any “Found Hardware” dialogs
Install Keysight IO Libraries Suite
Keysight IO Libraries Suite 16.0 (or later) is required for the PXI modules. It
includes the Keysight Connection Expert, the IVI Shared Components, and the
VISA Shared Components.
1Insert the Automation-Ready CD with Keysight IO Libraries Suite into the
CD-ROM drive of your system controller. Wait a few seconds for the auto-run
window to appear. If the auto-run window does not appear automatically:
–Click Start > Run...
–Type: <drive>:Autorun\IOLibraries.hta
where <drive> is your CD drive letter.
2Follow the installation instructions that came with the IO Libraries Suite.
Keysight IO Libraries version 16.0 (or later) must be installed prior
to installing and running any other software and prior to powering
the chassis. The latest version can be downloaded from:
www.keysight.com/find/iosuite.
If the IVI Shared Components and VISA Shared Components are not
already installed on your PC, Keysight IO Libraries Suite installs
them in the default locations. If they are already installed, the
installer upgrades them to the latest version, using the same
location used by the older version. If this is a first-time
installation, you can select installation locations for these
components by choosing a Custom Installation.

Keysight M9187A PXI Digital IO Startup Guide 15
Step 3: Install the Software on the Host Computer
Install instrument drivers
1Insert the Digital IO Module Software and Product Information CD into the
CD-ROM drive of your PC.
Wait a few seconds for the auto-run window to appear. If the auto-run
window does not appear automatically:
–Click Start > Run...
–Type: <drive>:Autorun.exe where <drive> is your CD drive letter.
2Select the Install Software link. Follow the installer prompts. Accept all of the
default directories specified during installation if prompted.
3After the Welcome screen, you will be prompted three times for license
agreements. The software installer installs the following drivers:
–Keysight Modular Software License Agreement. The installer program
installs the Soft Front Panel (SFP) application and other object code to
connect to the module. Accept the license terms and click Next.
–Keysight IVI Driver Source Code License Agreement. The Interchangeable
Virtual Instrument (IVI) driver is available for programming the Keysight
modules using Microsoft development environments (e.g., Visual Studio, C,
C++, C#, Visual Basic), Keysight VEE, MATLAB, or National Instruments
Labview. Accept the license terms and click Next.
–Keysight Software License Agreement for drivers for use with LabVIEW
Software. The LAbVIEW driver provides access to the functionality of the
module through LabVIEW VIs. This driver works in National Instruments
LabVIEW development environments. Before this driver can be installed,
your computer must already have the IVI Shared Components installed.
Accept the license terms and click Next.
4Next, the installer indicates the LabVIEW installations found on your host
computer. Click Next
5After accepting the licenses, the driver software is ready to be installed on
your host computer. Click Install.
6When the installation wizard is finished, you will be prompted to reboot your
host computer. Do not reboot the host computer at this time! Select “No, I
will restart my computer later.” Power down the host computer.
Proceed to “Step 4. Connect the Controller to the PXI Chassis” on the next
page.
Installing Keysight IO Libraries also installs the IVI Shared
Components. The IVI Shared Components are required before IVI
drivers (e.g., IVI-COM, IVI-C) can be installed from the product
reference CD.

16 Keysight M9187A PXI Digital IO Startup Guide
Step 4. Connect the Controller to the PXI Chassis
Step 4. Connect the Controller to the PXI Chassis
Using a remote PC
Refer to the following figure. Make certain that both the PC and the PXI chassis
are turned off. Unplug the chassis from the ac power mains. If you are using the
M9018A 18 Slot PXIe chassis, install the Keysight M9021A PCIe Cable Interface
module in the chassis.
-If you are using a desktop or rack mount PC, install the M9047A PCIe Desktop
Adapter in the PC. With a Keysight Y1202A cable, connect the adapter to the
System Interface module.
-If you are using a laptop PC, install the M9045A PCIe ExpressCard Adapter in
the laptop. With a Keysight Y1200A cable, connect the adapter to the System
Interface module on the PXI chassis
.
Using an embedded computer
Refer to the figure above. If you are using an embedded controller in the PXI
chassis, you should have installed it prior to installing the Keysight IO Libraries
and instrument drivers. No cables or other adapters are required. After
installation, proceed to “Step 5: Install the Module in the PXI Chassis”
To ensure proper system operation and the PC’s ability to
enumerate all of the PXI modules, you must use an approved
embedded PC, desktop PC, or laptop PC along with approved
PCIe adaptor and cable.
Controller:System Interface:
PXI System Chassis:
18 Slot PXIe Chassis
M9021
Cable Interface
Module
Y1200A
PCIe Cable
M9045
PCIe Laptop
Adapter
Laptop PC
Y1202A
PCIe Cable
M9047
PCIe Desktop
Adapter
Rack mount PC
Desk mount or
PXIe Embedded
System Controller

Keysight M9187A PXI Digital IO Startup Guide 17
Step 5: Install the Module in the PXI Chassis
Step 5: Install the Module in the PXI Chassis
1Make sure the PXI chassis power is turned off.
2If the chassis has multiple fan speed settings, ensure that the fans are set to
automatic. Do not set the fan speed to low or turn them off.
3Position the chassis so that there is ample space between the chassis fan
intake and exhaust vents. Blockage by walls or obstructions affects the air
flow needed for cooling. (Refer to the chassis documentation for more
information about cooling).
4The modules are shipped with thread protectors over the mounting screws.
These must be removed before installing the modules in a chassis.
5Holding the PXI module by the injector/ejector handle, slide it into an
available PXI (or hybrid) slot, as shown in the following figure.
–Install the module in the PXI slot by
placing the module card edges into the
front module guides (top and bottom).
–Slide the module to the rear of the
chassis and assure that the
injector/ejector handle is pushed down
in the unlatched (downward) position.
–Slide the module completely into the
chassis. When you begin to feel resistance, push up on the injector/ejector
handle to fully seat the module into the chassis.
- PXI hard ware does not support “hot-swap” capabilities
(changing modules while power is applied to the chassis).
- Before installing Keysight PXI Modules into the chassis, the
chassis must be powered off to prevent damage to the PXI
module. Remove all cables/terminal blocks from the module
prior to installing or removing the module.
The module can be used in a chassis with a cPCI, PXI-1, or PXIh
chassis peripheral slot.
The module can be installed in any standard PXI slot
marked with a peripheral slot compatibility image (a
circle containing the slot number).
The module can also be installed in any hybrid PXI slot
marked with a peripheral slot compatibility image (the
letter “H” and a solid circle containing the slot
number).

18 Keysight M9187A PXI Digital IO Startup Guide
Step 5: Install the Module in the PXI Chassis
6Latch the module by pulling up on the injector/ejector handle and secure the
front panel to the chassis using the module mounting screws.
7Tighten the screws on the module (or remote controller) front panel.
Performance may suffer if the screws are not securely tightened.
8Install all chassis covers, filler panels, and air inlet modules after installing the
module. Missing filler panels may disrupt necessary air circulation in the
chassis.
9If you are using a remote controller, connect the System Interface Card in the
chassis to the host computer.
10 Plug in and power up the PXI chassis. Verify that the chassis fans are
operating and free of obstructions that may restrict airflow.
11 If you are using a remote host computer (rack mount, desktop, or laptop PC),
power-on the computer. Choose the default option for any “Found New
Hardware” dialogs.
Chassis Power Down Process
If you are using a remote controller linked to the M9021A Cable
Interface, you must power up the chassis BEFORE you power up
the PC. When you power down your system, you must Shut Down
the PC BEFORE you power down the chassis.
If you are using MXI-3 to connect a desktop PC to a PXI chassis or
link to multiple chassis, power up the system as follows:
-For a system with a PC and one chassis, power up the chassis
before powering the PC.
-For a system with more than one chassis, power on the last
chassis in the system followed by the penultimate, etc. Finally,
turn on the PC or chassis containing the system controller.
After all of the “Found New Hardware” dialogs are complete, you
must reboot the host computer.
If you are using a remote controller linked to the M9021A Cable
Interface, you must Shut Down the PC BEFORE you power down
the chassis. When you restore power, you must power up the
chassis BEFORE you power up the PC.

Keysight M9187A PXI Digital IO Startup Guide 19
Step 6. Verify Operation of the Module
Step 6. Verify Operation of the Module
Run Keysight IO Libraries Connection Expert
If Keysight Connection Expert is already running on the system controller, click
the Refresh All button to identify any hardware you have just installed or
re-connected.
If Connection Expert is not already running, run it now to verify your I/O
configuration. In the Windows Notification Area, click the IO icon ( ), then click
Keysight Connection Expert.
Locate your interfaces and instruments in the Keysight Connection Expert
Explorer Pane. The following graphic shows the Connection Expert screen.
Select the module in the center pane (Instrument I/O on this PC). The right-hand
Pane shows the instrument properties. Select the Installed Drivers tab
then click the Start SFP button. You can use the M9187A Soft Front Panel
(SFP) software to set the outputs read the inputs, and verify operation of the
module. The Soft Front Panel software was installed as part of the Software
installation process.
For detailed instructions for using the M9187A Digital IO module, refer to the
Soft Front Panel help file on the Digital IO Module Software and Product
Information CD.

20 Keysight M9187A PXI Digital IO Startup Guide
Step 6. Verify Operation of the Module
Refer to the SFP help file on the Digital IO Module Software and Product
Information CD for specific detailed information on the SFP. The following graphic
shows an example of the SFP for the M9187A PXI Digital IO module.
If you have another application, either your own program or another instance of
the SFP interface, that has initialized the M9187A module, then the SFP enters it’s
“monitor” mode. In this mode, you must check the “Allow Control” check box (upper
left corner) before you can actually set the digital output channels. If Allow Control
is not checked, the Output Channels section of the SFP display is grayed out.
Selecting the Continuous button allows the SFP monitor mode to continuously read
and update the state of the digital inputs regardless of whether the Allow Control
check box is checked or not. The “light” next to the Continuous button flashes to
indicate the SFP is reading and updating the display.
Verify operation
There are no specific operational verification or self test procedures. However, you
can use the Soft Front Panel software to set the outputs and read the inputs.
Module specifications are guaranteed by design.