Moxa Technologies ioLogik E1210 User manual

ioLogik E1200 Series User’s Manual
Edition 12.0, October 2016
www.moxa.com/product
© 2016 Moxa Inc. All rights reserved.

ioLogik E1200 Series User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2016 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa China (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax:
[phone]
Mo
xa Asia-Pacific
Tel:
[phone]
Fax:
[phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Product Features ................................................................................................................................1-2
Inside the Box....................................................................................................................................1-2
Product Model Information...................................................................................................................1-3
Product Specifications .........................................................................................................................1-4
Common Specifications ................................................................................................................1-4
ioLogik E1210.............................................................................................................................1-5
ioLogik E1211.............................................................................................................................1-5
ioLogik E1212.............................................................................................................................1-6
ioLogik E1213.............................................................................................................................1-7
ioLogik E1214.............................................................................................................................1-8
ioLogik E1240.............................................................................................................................1-9
ioLogik E1241.............................................................................................................................1-9
ioLogik E1242...........................................................................................................................1-10
ioLogik E1260...........................................................................................................................1-11
ioLogik E1262...........................................................................................................................1-12
Physical Dimensions..........................................................................................................................1-13
Hardware Reference..........................................................................................................................1-14
Panel Guide ..............................................................................................................................1-14
Ethernet Port ............................................................................................................................1-14
LED Indicators ..........................................................................................................................1-14
I/O Circuit Diagram...........................................................................................................................1-15
DI Circuit .................................................................................................................................1-15
Sinking DO Circuit .....................................................................................................................1-15
Sourcing DO Circuit ...................................................................................................................1-16
DIO Circuit ...............................................................................................................................1-17
Relay Circuit.............................................................................................................................1-18
AI Circuit..................................................................................................................................1-18
RTD Circuit...............................................................................................................................1-18
TC Circuit.................................................................................................................................1-19
2. Initial Setup...................................................................................................................................... 2-1
Hardware Installation..........................................................................................................................2-2
Connecting the Power ..................................................................................................................2-2
Grounding the ioLogik E1200........................................................................................................2-2
DIN Rail, Wall Mounting ...............................................................................................................2-2
Connecting to the Network ...........................................................................................................2-3
Jumper Settings (DIO and AI).......................................................................................................2-3
I/O Wiring Diagrams....................................................................................................................2-5
ioSearch™ Installation.........................................................................................................................2-7
Load Factory Default Settings...............................................................................................................2-7
3. Using the Web Console...................................................................................................................... 3-1
Introduction to the Web Console...........................................................................................................3-2
Overview...........................................................................................................................................3-3
Network Settings for the Web Console...................................................................................................3-4
General Settings .........................................................................................................................3-4
Ethernet Configuration.................................................................................................................3-4
User-Defined Modbus Addressing..........................................................................................................3-5
Default Modbus Address...............................................................................................................3-5
AOPC Server Settings..........................................................................................................................3-6
Tag Generation ...........................................................................................................................3-6
I/O Settings.......................................................................................................................................3-8
DI Channels................................................................................................................................3-8
DO Channels.............................................................................................................................3-10
AI Channels..............................................................................................................................3-11
AI Input Range .........................................................................................................................3-12
AO Channels.............................................................................................................................3-14
RTD Channels ...........................................................................................................................3-15
TC Channels .............................................................................................................................3-17
Peer-to-Peer Networking ...................................................................................................................3-18
Peer-to-Peer Settings (1-50) ......................................................................................................3-18
Sample Peer-to-Peer Configuration..............................................................................................3-19
DO Safe Mode Settings ..............................................................................................................3-20
AO Safe Mode Settings...............................................................................................................3-20
SNMP..............................................................................................................................................3-20
SNMP Trap ...............................................................................................................................3-20
Using SNMP..............................................................................................................................3-21
Accessibility IP List ....................................................................................................................3-25
RESTful API Setting ..........................................................................................................................3-26

EtherNet/IP Setting...........................................................................................................................3-26
System Management.........................................................................................................................3-27
Network Connection ..................................................................................................................3-27
Firmware Update.......................................................................................................................3-27
Import System Configuration Settings .........................................................................................3-27
Export System Settings..............................................................................................................3-28
Change Password .............................................................................................................................3-28
Load Factory Defaults........................................................................................................................3-28
Save/Restart....................................................................................................................................3-29
4. Using ioSearch™................................................................................................................................ 4-1
Introduction to ioSearch™ ...................................................................................................................4-2
ioSearch™ Main Screen .......................................................................................................................4-2
Main Screen Overview..................................................................................................................4-2
ioSearch™ Setup ................................................................................................................................4-3
System ......................................................................................................................................4-3
Sort...........................................................................................................................................4-4
Quick Links.................................................................................................................................4-4
Main Function.....................................................................................................................................4-4
Locate .......................................................................................................................................4-5
Firmware Upgrade.......................................................................................................................4-5
Unlock .......................................................................................................................................4-5
Import.......................................................................................................................................4-6
Export .......................................................................................................................................4-6
Change IP Address ......................................................................................................................4-7
Batch TCP/IP Configuration on Multiple Devices...............................................................................4-7
Change Server Name...................................................................................................................4-8
Activate EtherNet/IP....................................................................................................................4-8
Restart System ...........................................................................................................................4-9
Reset to Default........................................................................................................................4-10
Mass Deployment (Import).........................................................................................................4-10
Mass Deployment (Export) .........................................................................................................4-10
5. Activation Process for the EtherNet/IP Function .............................................................................. 5-1
6. How to Connect the ioLogik E1200 to an Allen-Bradley PLC .............................................................. 6-1
EDS Installation of the ioLogik E1200 Series in Rockwell Software RSLogix 5000 ........................................6-2
Establishing communication between the ioLogik E1200 device and the Allen-Bradley PLC...........................6-6
A. Modbus/TCP Default Address Mappings............................................................................................ A-1
ioLogik E1210 Modbus Address and Register Map ...................................................................................A-2
ioLogik E1211 Modbus Address and Register Map ...................................................................................A-3
ioLogik E1212 Modbus Address and Register Map ...................................................................................A-5
ioLogik E1213 Modbus Address and Register Map ...................................................................................A-7
ioLogik E1214 Modbus Address and Register Map ...................................................................................A-9
ioLogik E1240 Modbus Address and Register Map .................................................................................A-11
ioLogik E1241 Modbus Address and Register Map .................................................................................A-12
ioLogik E1242 Modbus Address and Register Map .................................................................................A-14
ioLogik E1260 Modbus Address and Register Map .................................................................................A-16
ioLogik E1262 Modbus Address and Register Map .................................................................................A-18
B. EtherNet/IP Default Address Mappings ............................................................................................ B-1
ioLogik E1200 EtherNet/IP Map ............................................................................................................B-1
C. RESTful API Default Address Mappings ............................................................................................. C-1
ioLogik E1200 RESTful API Map ............................................................................................................C-1
D. Network Port Numbers......................................................................................................................D-1
E. Factory Default Settings.................................................................................................................... E-1
F. Pinouts.............................................................................................................................................. F-1
G. FCC Interference Statement..............................................................................................................G-1
H. European Community (CE) ................................................................................................................H-1

1
1. Introduction
The ioLogik E1200 industrial Ethernet remote I/O has two embedded Ethernet switch ports that allow
information to flow to another local Ethernet device or connect to the next ioLogik in a daisy-chain. Applications
such as factory automation, security and surveillance systems, and tunnel monitoring, can make use of
daisy-chained Ethernet for building multidrop I/O networks over standard Ethernet cables and familiar fieldbus
protocols. The daisy-chain function on the ioLogik E1200 Ethernet remote I/O not only increases the
connections between machines and panels, but it also lowers the cost of buying separate Ethernet switches,
and at the same time reduces labor fees and cabling by a large percentage. For example, if a production facility
contains 700 stations (20 points per station), the wiring cost reduction can reach 15% of the total
implementation cost.
The following topics are covered in this chapter:

Product Features

Inside the Box

Product Model Information

Product Specifications
Common Specifications
ioLogik E1210
ioLogik E1211
ioLogik E1212
ioLogik E1213
ioLogik E1214
ioLogik E1240
ioLogik E1241
ioLogik E1242
ioLogik E1260
ioLogik E1262

Physical Dimensions

Hardware Reference
Panel Guide
Ethernet Port
LED Indicators

I/O Circuit Diagram
DI Circuit
Sinking DO Circuit
Sourcing DO Circuit
DIO Circuit
Relay Circuit
AI Circuit
RTD Circuit
TC Circuit

ioLogik E1200 Series Introduction
1-2
Product Features
•Active communication with patented MX-AOPC UA Server
•2-port Ethernet switch for daisy-chain topologies
•Easy mass deployment and configuration with ioSearch™utility
•User-friendly configuration via web browser
•Save time and wiring costs with peer-to-peer communication
•User-defined Modbus/TCP addressing
•Simplify I/O management with MXIO library on either Windows or Linux platform
•Wide operating temperature: -40 to 75°C (-40 to 167°F)
•Supports SNMPv1/v2c
•UL/cUL Class I Division 2, ATEX Zone 2 certification
Inside the Box
The ioLogik E1200 is shipped with the following items:
•ioLogik E1200 remote Ethernet I/O server
•Quick installation guide (printed)
NOTE
Notify your sales representative if any of the above items are missing or damaged.

ioLogik E1200 Series Introduction
1-3
Product Model Information
Model Description
ioLogik E1210 Remote Ethernet I/O with 2-port Ethernet switch and 16 DIs
ioLogik E1211 Remote Ethernet I/O with 2-port Ethernet switch and 16 DOs
ioLogik E1212 Remote Ethernet I/O with 2-port Ethernet switch, 8 DIs, and 8 DIOs
ioLogik E1213 Remote Ethernet I/O with 2-port Ethernet switch, 8 DIs, 4 DOs, and 4 DIOs (source
type)
ioLogik E1214 Remote Ethernet I/O with 2-port Ethernet switch, 6 DIs, and 6 relays
ioLogik E1240 Remote Ethernet I/O with 2-port Ethernet switch and 8 AIs
ioLogik E1241 Remote Ethernet I/O with 2-port Ethernet switch and 4 AOs
ioLogik E1242 Remote Ethernet I/O with 2-port Ethernet switch and 4 AIs, 4DIs, and 4DIOs
ioLogik E1260 Remote Ethernet I/O with 2-port Ethernet switch and 6 RTDs
ioLogik E1262 Remote Ethernet I/O with 2-port Ethernet switch and 8 TCs
ioLogik E1210-T Ethernet remote I/O with 2-port Ethernet switch and 16 DIs, -40 to 75°C operating
temperature
ioLogik E1211-T Ethernet remote I/O with 2-port Ethernet switch and 16 DOs, -40 to 75°C operating
temperature
ioLogik E1212-T Ethernet remote I/O with 2-port Ethernet switch, 8 DIs, and 8 DIOs, -40 to 75°C
operating temperature
ioLogik E1213-T Remote Ethernet I/O with 2 Port Ethernet switch, 8 DIs, 4 DOs, and 4 DIOs (source
type), -40 to 75°C operating temperature
ioLogik E1214-T Ethernet remote I/O with 2-port Ethernet switch, 6 DIs, and 6 Relays, -40 to 75°C
operating temperature
ioLogik E1240-T Ethernet remote I/O with 2-port Ethernet switch and 8 AIs, -40 to 75°C operating
temperature
ioLogik E1241-T Ethernet remote I/O with 2-port Ethernet switch and 4 AOs , -40 to 75°C operating
temperature
ioLogik E1242-T Ethernet remote I/O with 2-port Ethernet switch, 4 AIs, 4 DIs, and 4 DIOs, -40 to 75°C
operating temperature
ioLogik E1260-T Ethernet remote I/O with 2-port Ethernet switch and 6 RTDs, -40 to 75°C operating
temperature
ioLogik E1262-T Ethernet remote I/O with 2-port Ethernet switch and 8 TCs, -40 to 75°C operating
temperature

ioLogik E1200 Series Introduction
1-4
Product Specifications
Common Specifications
LAN
Ethernet:
2 switched 10/100 Mbps RJ45 ports
Protection:
1.5 kV magnetic isolation
Protocols:
Modbus/TCP (Slave), EtherNet/IP, SNMPv1/v2c, RESTful API, TCP/IP, UDP, DHCP, BOOTP, HTTP
Physical Characteristics
Wiring:
I/O cable max. 14 AWG
Dimensions:
27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)
Weight:
Under 200 g (0.44 lb)
Mounting:
DIN rail or wall
Environmental Limits
Operating Temperature:
Standard Models:
-10 to 60°C (14 to 140°F)
Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity:
5 to 95% (non-condensing)
Shock:
IEC 60068-2-27
Vibration:
IEC 60068-2-6
Altitude:
Up to 2000 m
Note:
Please contact Moxa if you require products guaranteed to function properly at higher altitudes.
Standards and Certifications
Safety:
UL 508
EMC:
EN 55022, EN 55024
EMI:
CISPR 22, FCC Part 15B Class A
EMS:
IEC 61000
-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000
-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000
-4-4 EFT: Power: 2 kV; Signal: 1 kV
IEC 61000
-4-5 Surge: Power: 2 kV; Signal: 1 kV
IEC 61000
-4-6 CS: 10 V
IEC 61000
-4-8
Hazardous Location:
Class 1 Division 2, ATEX Zone 2
Green Product:
RoHS, CRoHS, WEEE
Note: Please check Moxa’s website for the most up
-to-date certification status.
Warranty
Warranty Period:
5 years (excluding the ioLogik E1214)
Details:
See www.moxa.com/warranty
Note: Because of the limited lifetime of power relays, products that
use this component are covered by a 2-
year
warranty.

ioLogik E1200 Series Introduction
1-5
ioLogik E1210
Inputs and Outputs
Digital Inputs:
16 channels
Isolation:
3k VDC or 2k Vrms
Digital Input
Sensor Type:
Wet Contact (NPN or PNP), Dry Contact
I/O Mode:
DI or Event Counter
Dry
Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type:
8 points per COM
Counter Frequency:
250 Hz
Digital Filtering Time Interval:
Software configurable
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
110 mA @ 24 VDC
MTBF (mean time between failures)
Time:
671,345 hrs
Standard:
Telcordia SR332
ioLogik E1211
Inputs and Outputs
Digital Outputs:
16 channels
Isolation:
3k VDC or 2k Vrms
Digital Output
Type:
Sink
I/O Mode:
DO or Pulse Output
Pulse Output Frequency:
500 Hz
Over
-Voltage Protection: 45 VDC
Over
-Current Protection: 2.6 A (4 channels @ 650 mA)
Over
-Temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating:
200 mA per channel
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
200 mA @ 24 VDC
MTBF (mean time between failures)
Time:
923,027 hrs
Standard:
Telcordia SR332

ioLogik E1200 Series Introduction
1-6
ioLogik E1212
Inputs and Outputs
Digital Inputs:
8 channels
Configurable DIOs (by jumper):
8 channels
Isolation:
3k VDC or 2k Vrms
Digital Input
Sensor Type:
Wet Contact (NPN or PNP), Dry Contact
I/O Mode:
DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type:
8 points per COM
Counter Frequency:
250 Hz
Digital Filtering Time Interval:
Software Configurable
Digital Output
Type:
Sink
I/O Mode:
DO or Pulse Output
Pulse Output Frequency:
500 Hz
Over
-Voltage Protection: 45 VDC
Over
-Current Protection: 2.6 A (4 channels @ 650 mA)
Over
-Temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating:
200 mA per channel
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
155 mA @ 24 VDC
MTBF
(mean time between failures)
Time:
561,930 hrs
Standard:
Telcordia SR332

ioLogik E1200 Series Introduction
1-7
ioLogik E1213
Inputs and Outputs
Digital Inputs:
8 channels
Digital Outputs:
4 channels
Configurable DIOs (by jumper):
4 channels
Isolation:
3k VDC or 2k Vrms
Digital Input
Sensor Type:
Wet Contact (NPN or PNP), Dry Contact
I/O Mode:
DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type:
12 points per COM
Counter Frequency:
250 Hz
Digital Filtering
Time Interval: Software configurable
Digital Output
Type:
Source
I/O Mode:
DO or Pulse Output
Pulse Output Frequency:
500 Hz
Over
-Voltage Protection: 41 VDC
Over
-current Protection: 1.5 A per channel @ 25°C
Over
-Temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating:
500 mA per channel
Power Requirements
Output Voltage Rating:
15 to 30 VDC (12 or 9 VDC configurable by jumper on the 4 DO channels)
Input Voltage:
12 to 36 VDC
Input Current:
130 mA @ 24 VDC
MTBF (mean time between failures)
Time:
715,256 hrs
Standard:
Telcordia SR332

ioLogik E1200 Series Introduction
1-8
ioLogik E1214
Inputs and Outputs
Digital Inputs:
6 channels
Relays:
6 channels
Isolation:
3k VDC or 2k Vrms
Digital Input
Sensor Type:
Wet Contact (NPN or PNP), Dry Contact
I/O Mode:
DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type:
6 points per COM
Counter Frequency:
250 Hz
Digital Filtering
Time Interval: Software configurable
Relay
Note: Ambient humidity must be non
-
condensing and remain between 5 and 95%. The relays of the ioLogik
E1214 may malfunction when operating in high condensation environments below 0°C.
Type:
Form A (N.O.) power relay
Contact Current Rating:
Resistive Load: 5 A @ 30 VDC, 250 VAC, 110 VAC
Breakdown Voltage:
500 VAC
Relay On/Off Time:
1500 ms (max.)
Initial Insulation Resistance:
1000 mega-ohms (min.) @ 500 VDC
Mechanical Endurance:
5,000,000 operations
Electrical Endurance:
100,000 operations @ 5 A resistive load
Contact Resistance:
100 milli-ohms (max.)
Pulse Output:
0.3 Hz at rated load
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
188 mA @ 24 VDC
MTBF
(mean time between failures)
Time:
808,744 hrs
Standard:
Telcordia SR332

ioLogik E1200 Series Introduction
1-9
ioLogik E1240
Inputs and Outputs
Analog Inputs:
8 channels
Isolation:
3k VDC or 2k Vrms
Analog Input
Type:
Differential input
Resolution:
16 bits
I/O Mode:
Voltage / Current (jumper selectable)
Input Range:
0 to 10 VDC, 0 to 20 mA, 4 to 20 mA, 4 to 20 mA (burnout detection)
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @
-10 and 60°C
±0.5% FSR @
-40 and 75°C
Sampling Rate:
• All channels: 12 samples/sec
• Per
channel: 1.5 samples/sec
• Only one channel enabled: 12 samples/sec
Input Impedance:
10 mega-ohms (min.)
Built
-in Resistor for Current Input: 120 ohms
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
121 mA @ 24 VDC
MTBF
(mean time between failures)
Time:
474,053 hrs
Standard:
Telcordia SR332
ioLogik E1241
Inputs and Outputs
Analog Outputs:
4 channels
Isolation:
3k VDC or 2k Vrms
Analog Output
Resolution:
12 bits
Output Range:
0 to 10 VDC, 4 to 20 mA
Drive Voltage:
10 mA (max.)
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @
-40 and 75°C
Load Resistor:
Internal register, 400 ohms
Note: 24 V of external power required when loading exceeds 1000 ohms.
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
194 mA @ 24 VDC
MTBF (mean time between failures)
Time:
888,656 hrs
Standard:
Telcordia SR332

ioLogik E1200 Series Introduction
1-10
ioLogik E1242
Inputs and Outputs
Digital Inputs:
4 channels
Configurable DIOs (by jumper):
4 channels
Analog Inputs:
4 channels
Isolation:
3k VDC or 2k Vrms
Digital Input
Sensor Type:
Wet Contact (NPN or PNP), Dry Contact
I/O Mode:
DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type:
4 points per COM
Counter Frequency:
250 Hz
Digital Filtering Time Interval:
Software Configurable
Digital Output
Type:
Sink
I/O Mode:
DO or Pulse Output
Pulse Output Frequency:
500 Hz
Over
-Voltage Protection: 45 VDC
Over
-Current Protection: 2.6 A (4 channels @ 650 mA)
Over
-Temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating:
200 mA per channel
Analog Input
Type:
Differential input
Resolution:
16 bits
I/O Mode:
Voltage / Current (jumper selectable)
Input Range:
0 to 10 VDC, 0 to 20 mA, 4 to 20 mA, 4 to 20 mA (burnout detection)
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @
-10 and 60°C
±0.5% FSR @
-40 and 75°C
Sampling Rate:
• All channels: 12 samples/sec
• Per channel: 3 samples/sec
• Only one channel enabled: 12
samples/sec
Input Impedance:
10 mega-ohms (min.)
Built
-in Resistor for Current Input: 120 ohms
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
139 mA @ 24 VDC
MTBF (mean time between failures)
Time:
502,210 hrs
Standard:
Telcordia SR332

ioLogik E1200 Series Introduction
1-11
ioLogik E1260
Inputs and Outputs
RTDs:
6 channels
Isolation:
3k VDC or 2k Vrms
RTD
Sensor Type:
• PT50, PT100, PT200, PT500 (
-200 to 850°C)
• PT1000 (
-200 to 350°C)
• Resistance of 310, 620, 1250, and 2200 ohms
Input
Connection: 2- or 3-wire
Sampling Rate:
• All channels: 12 samples/sec
• Per channel: 2 samples/sec
• Only one channel enabled: 12 samples/sec
Resolution:
0.1°C or 0.1 ohm
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @
-40 and 75°C
Input Impedance:
625 kilo-ohms
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
110 mA @ 24 VDC
MTBF
(mean time between failures)
Time:
660,260 hrs.
Standard:
Telcordia SR332

ioLogik E1200 Series Introduction
1-12
ioLogik E1262
Inputs and Outputs
Thermocouples:
8 channels
Isolation:
3k VDC or 2k Vrms
Thermocouple
Sensor Type:
J (0 to 750°C), K (-200 to 1250°C), T (-200 to 350°C),
E (
-200 to 900°C), R (-50 to 1600°C), S (-50 to 1760°C), B (600 to 1700°C), N (-200 to 1300°C)
Millivolt Type:
• Mode: ±78.126 mV, ±39.062 mV, ±19.532 mV
• Fault and over
-voltage protection:
-35 to +35 VDC (power off)
-25 to +30 VDC (power on)
Sampling Rate:
• All channels: 12 samples/sec
• Per channel: 1.5 samples/sec
• Only one channel enabled: 12 samples
/sec
Resolution:
16 bits
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @
-40 and 75°C
Input Impedance:
10 mega-ohms
Power Requirements
Input Voltage:
12 to 36 VDC
Input Current:
118 mA @ 24 VDC
MTBF (mean time between failures)
Time:
631,418 hrs.
Standard:
Telcordia SR332

ioLogik E1200 Series Introduction
1-13
Physical Dimensions

ioLogik E1200 Series Introduction
1-14
Hardware Reference
Panel Guide
NOTE
The RESET button restarts the server and resets all settings to factory defaults. Use a pointed object such as
a straightened paper clip to hold down the RESET button for 5 seconds. The factory defaults will be loaded once
the READY LED turns green again. You may then release the RESET button.
Ethernet Port
Pin 1 2 3 4
Signal TXD+ TXD- RXD+ ---
Pin 5 6 7 8
Signal --- RXD- --- ---
LED Indicators
LED State Description
Power Amber System power is ON
OFF System power is OFF
Ready Green System is ready
Flashing Flashes every 1 second when the “Locate” function is triggered
Flashing Flashes every 0.5 second when the firmware is being upgraded
Flashing ON/OFF cycle period of 0.5 second represents “Safe Mode”
OFF System is not ready
Port 1 Green Ethernet connection enabled
Flashing Transmitting or receiving data
Port 2 Green Ethernet connection enabled
Flashing Transmitting or receiving data
EXT Green EXT field power input is connected
Off EXT field power input is disconnected

ioLogik E1200 Series Introduction
1-15
I/O Circuit Diagram
DI Circuit
Sinking DO Circuit

ioLogik E1200 Series Introduction
1-16
Sourcing DO Circuit