Kilews SKD-BE512P User manual

OPERATION AND MAINTENANCE MANUAL
SKD-BE512L
SKD-BE519L
SKD-BE512LF
SKD-BE517LF
SKD-BE512P
SKD-BE519P
SKD-BE512PF
SKD-BE517PF
DC-TYPE Automatic Non-Carbon-Brush with Counter Series
KILEWS INDUSTRIAL CO., LTD.
www.kilewswest.com
KILEWS WEST USA INC. - 6945 LTC PKWY - PORT ST LUCIE, FL 34986
PHONE [phone] FAX [phone] EMAIL [email protected]
Y2F032A-E-003
Ver. 3.0


1
Metal Assembly Screwdrivers are designed for installing threaded fasteners in light industrial and appliance
manufacturing applications.
KILEWS is not responsible for customer modification of tools for applications on which KILEWS was not
consulted.
Important safety information enclosed.
Read all these instructions before placing tool in service or operation this tool and save these instructions. It is
the responsibility of the employer to place the information in this manual into the hands of the operator. Failure
to observe the following warnings could result in injury. When using electric tools, Basic safety precautions
should always be followed to reduce the risk of fire, electric shock and personal injury, including the following:
WARNING
NOTICE


2
WARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock
fire and/or serious injure. The term “power tool” in all of the warning listed below refers to your mains operated
(corded) power tool or battery operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Electrical Safety
a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate power tools in explosive atmosphere, such as in the presence of flammable liquids,
gases or dust. Power tools create sparks which may ignite the dust of fumes.
c)Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
2) Electrical Safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Don’t expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord to carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of
cord suitable for outdoor use reduces the risk of electric shock.
3) Personal Safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use power tool while you are tired or under the influence of drugs, alcohol, or medication. Amoment
of inattention while operating power tools may result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
Rubber gloves and non-skid footwear are recommended when working outdoors.
c) Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power
tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.
d) Remove any adjusting keys or wrench before turning the power tool on. A wrench or a key that is left
attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away
from moving parts. Loose clothes, jewellery, or long hair can be caught in moving parts
g) Secure work. Use clamps or a vice to hold the work. It is safer than using your hand and frees
both hands to operate the tool.
h) If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of these devices can reduce dust related hazards.
Important Safety Rules


3
4) Power tool Use and Care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will
do the job better and safer at the rate for which it was designed.
b) Do not use power tool if switch does not turn it on or off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before making any adjustments, changing accessories,
or storing the power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of reach of children and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained
users.
Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the power tools operation. If damaged, have the power tool repaired
before use. Many accidents are cause by poorly maintained power tools.
Inspect extension cords periodically and replace, if damaged.
f) Keep cutting tools sharp and clean, properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tools, accessories and tool bits etc., in accordance with these instructions and in the
manner intended for the particular type of power tool, taking into account the working conditions
and the work to be performed. Use of the power tool for operations different from intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by qualified repair person using only identical replacement parts, this will
ensure that the safety of the power tool is maintained.
Additional information shall be provide
a) Instruction for putting into use
1. Setting-up or fixing power tool in a stable position as appropriate for power tools which can be mounted
on a support.
2. Assembly
3. Connection to power supply, cabling, fusing, socket type and earthing requirements.
4. Illustrated description of functions.
5. Limitations on ambient conditions.
6. List of contents.
b) Operating Instructions.
1. Setting and testing.
2. Tool changing.
3. Clamping of work.
4. Limits on size of work piece.
5. General instructions for use.
c) Maintenance and servicing.
1. Regular cleaning, maintenance, and lubrication.
2. Servicing by manufacture or agent, list of addresses.
3. List of user-replaceable parts.
4. Special tools which may be required.


4
WARNING！
DO NOT OPERATE THIS TOOL WITHOUT
PROTECTIVE EARTH CONNECTED
1、This tool should be grounded while in use to protect the operator from electric shock. NOTICE! To ensure
the grounding result, the grounding conductor of the power cord must be well connected with the
grounding terminal of power facility. This tool is equipped with grounding conductors. The Green (or Green
and Yellow) conductor in the Power Cord is the grounding wire. Never connect Green (or Green and
Yellow) to a live terminal. The grounding wires in this tool can not only earth the electric leakage safely, but
also can eliminate ESD-the electrostatic that tool occurred while in use.
2、The grounding is the most important task a user. Periodically, depends on the working condition and
circumstance, for maintaining a good function the user has to check the grounding condition every 3~6
months by an electric meter and following simple steps; Set the Ohm meter to level R*100(Ohm).
Touching 2 test rods (“＋”＆”－”) together and reset the meter to “0”. Using the Red(“＋”) rod to touch the
Grounding wire on the Plug of controller’s cord, and the Black(“－”) rod to the end of Bit Head. It stands for
the grounding is normal if the meter is read as close as to “0”. For getting a normal indication on the meter
while in testing, need to press the test rods firmly to the testing objects.
3、The instrument QC of the tool is performed before the tool ex-factory. The grounding continuity test is
conducted by input 26A voltage to the end of earth terminal, and subject to the resistance value lower than
0.3Ohm.
Grounding Instructions


5
1) Whenever changing a bit, make certain the Forward / Reverse Switch is in the “OFF “position and tool is
unplugged.
2) Do not allow chemicals such as acetone, benzene, thinner, trichloroethylene ketone, or other similar
chemicals to come in contact with the screwdriver housing as damage will result.
3) Do not drop or abuse the screwdriver.
4) Do not adjust the torque setting higher than 8 on the torque scale.
5) There should be a tool rest interval when cycles three seconds or longer. This tool is intended for a duty
cycle of 1.0 sec on, 3.0 sec off.
6) Do not use this screwdriver for tightening wood screws. This is “Metal Assembly Screw Driver”
7) Do not operate the Forward / Reverse Switch the motor is running.
8) Whenever a tool is not being used, move the Forward / Reverse Switch to the “OFF” position and unplug
the screwdriver.
9) Don't touch For&Rew Switch during operating for keeping system from wrong judgment.
●Do not drop or abuse the tool.
●Whenever a tool is not being used, position the Power Switch to the “OFF” position and unplug the power
cord.
OperationsCautions
CAUTION


6
Attaching / detaching bit and bit type
Push up the holder clamp by finger tip, and it will be unlocked. Thus, the bit can be freely attached and
detached (single finger notion type) select such a bit whose shank is equal to the size shown below.
Insert the power plug into a receptacle and set the changeover switch to “F”position.
Apply the bit to the screw head and press the lever or push main body to, then the switch will be turned
ON to start the motor running.
When the screw is tighten and reach the torque that you had set, The tool will stopped automatically.
To reset the tool by releasing the lever to the original position or releasing the bit from the screw head.
To return the screw, set the changeover switch to “R” position.
Maintenance and Inspection:
1. The screw driver must be operated in top condition, one day working hour must be
not more than eight hours.
2. Please note don’t let the motor get over heated, every minute use 10~15 screws to operate.
3. The frequency use of this electric screw driver is over than eight hours a day, still it needs periodically
testing and treatment. Every 5-6 months.
4. Inspect tool cords periodically and if damaged, have them repaired by an authorized service facility.
Inspect extension cords periodically and replace if damaged.
5. Do not remove any labels. Replace any damaged label.
Description of Operation
Servicing


7
1. The use of other than genuine KILEWS replacement parts may Result in decreased
tool performance and increased maintenance, and may invalidate all warranties.
2. All repairs and maintenance of this tool and its word must be performed by an authorized service center.
3. KILEWS is not responsible for customer modification of tools for applications on which KILEWS was not
consulted.
4. Repairs should by made only by authorized, trained personnel. Consult your nearest KILEWS authorized
service center.
5. It is the responsibility of the employer to place the information in this manual into the hands of the operator.
DO NOT ATTEMPT TO REPAIR THIS
ELECTRIC SCREW DRIVER
SAVE THESE INSTRUCTIONS
DO NOT DESTROY
CAUTION
CAUTION


8
MODEL SKD-BE512L SKD-BE519L SKD-BE512P SKD-BE519P
Input voltage(DC) DC 24V OR 32V
Power Consumption 55W
Torque
(kgf.cm) 1.5-12 3-19 2-12 3-19
(Lbf.in) 1.33-10.44 2.57-16.46 1.77-10.44 2.57-16.46
(N.m) 0.15-1.18 0.29-1.86 0.2-1.18 0.29-1.86
Repeatable Torque Accuracy (%) ±3%
Torque Adjustment Step less
Unloaded Rotation
Speed (r.p.m) )±10%
HI 1000 1000 1000 1000
LO 700 700 700 700
Screw Size
Dia(mm)
Machine screw 1.6~3.0 2.3~3.5 1.6~3.0 2.3~3.5
Tapping screw 1.6~2.6 2.3~3.0 1.6~2.6 2.3~3.0
Weight (g) 580
Length (mm) 270
Model of Torque Fixing Ring KC-6C、KC-6S
Power controller SKP-32B-60W
Model of Suspension Rack KH-4、(KC & KH-2)
Bit Type
HEX5mm, HEX6.35mm Ø4mm, Ø5mm
MODEL SKD-BE512LF SKD-BE512PF SKD-BE517LF SKD-BE517PF
Input voltage(DC) DC 32V
Power Consumption 55W
Torque
(kgf.cm) 1.5-12 2-12 3-17 3-17
(Lbf.in) 1.33-10.44 1.77-10.44 2.57-14.78 2.57-14.78
(N.m) 0.15-1.18 0.2-1.18 0.29-1.67 0.29-1.67
Repeatable Torque Accuracy (%) ±3%
Torque Adjustment Step less
Unloaded Rotation
Speed (R.p.m) )±10%
HI 2000 2000 2000 2000
LO - - - -
Screw Siz
Dia(mm)
Machine screw 1.6~3.0 1.6~3.0 2.3~3.5 2.3~3.5
Tapping screw 1.6~2.6 1.6~2.6 2.3~3.0 2.3~3.0
Weight (g) 580
Length (mm) 270
Model of Torque Fixing Ring KC-6C、KC-6S
Power controller SKP-BE32HL
Model of Suspension Rack KH-4、(KC & KH-2)
Bit Type
HEX5mm, HEX6.35mm Ø4mm, Ø5mm
* 1N.m=10.2Kgf.cm 1N.m=8.85Lbf.in
Specifications


9
1. Ｂit Type：No. 00 ．．． Bit use in dia 1.3~1.8mm screw
No. 0．．．． Bit use in dia 1.8~2.0mm screw
No. 1．．． ．Bit use in dia 2.0~2.6mm screw
No. 2．． ．．Bit use in dia 3.0~4.0mm screw
SKD-BE512 with BIT 1# & 2# 1 Pcs. Each
SKD-BE519 withBIT 1#&2# 1Pcs.Each
S
KD-BE512F withBIT 1#&2# 1Pcs.Each
SKD-BE517F withBIT 1#&2# 1Pcs.Each
2. Suspension rack and Torque fixing ring acceptable for use with the tool are available from KILEWS
catalogue.
3. Torque Fixing Ring (KC-6C) 1 Pcs.
NO Name Function
1 Three-Color Light
To Show operating is OK, N.G or in the mode
condition.
2 Panel To show set value, set screws number and other
value
3 Power Switch
Push five seconds: to disable COUNTING
FUNCTION
CLEAR Push three seconds: CLEAR
4 SELECT Key Push three seconds: Enter the system
5 Up Key When entering the system , this key increases
value
6 Down Key When entering the system , this key decreases
value
7 Reset Restore to factory settings
※S+P Automatic learning.
※UP+P Waiting time mode
※UP+DOWN Buzzer
mode
※S+UP If press together to enable P/R/S button, and then
press again to disable P/R/S button.
Accessories
PanelSpecifications
1
3
5
7
6
4
2


10
※Push three seconds to enter the selection ) SL===SC===At===Ht===Lt===LL===Ns===Rn===Rt <Confirm>
Function Name Set up Time and
Value Description Buzz Time/ Light
Factory
default
settings
SL 01-05/UU Screw List --- ---
SC 1-99 Counting number / count-down only --- 05
At 0.1-9.9 Automatic zero time / Signal output time --- 1.0
Ht 0.1-9.9 Ht time Stop time ( Show wrong as screwdriver can’t sop at
set time after starting, can be used to test stripped screws
Five buzz and LED red flash 2.0
Lt
0.01-9.9 Lt time will show wrong as screwdriver stops before Lt after
starting, can test screw is not properly fastened at its
position. .
Two buzz and LED red flash
0.00
LL 0.01-9.9 Reconfirm time after fastening. --- 0.00
Ns
Y or N Ns：Set the function of stopping the screwdriver when any
error message occurs.
Y: Stop the screwdriver when any error occurred meanwhile,
Reverse is OK; Restore by pressing “S” button
N: screwdriver could operate continually when any error
occurred.
Rn
Y or N Rn：Set the count-up mode for the reversion.
Y:taken in count for each reversion；N:Only count once when
reverse
Rt 0.01 – 9.99 Rt：Set auto reverse time after the screwdriver shutting off.
Backward to Count-Up 1 COUNT When screwdriver is backward, the number will be back one --- ---
LC --- Keypad LOCK P/S/R button
UN --- UNLOCK
Ln --- Automatic learning. LED keeps flash of light ---
Buzzer
En
Wrong
Set-Up
--- Wrong Set-Up, such as Lt＞Ht
Three buzz and LED red flash.
Automatically show En ---
dt
Standby
Time
Seconds buzz if set-number of screws are not completed in the allotted
set time for each screw fastening
Lasting buzz s and LED red
flash ---
Tt
Working
Time for a
set of
screwdriver
Minutes buzz if set-number of screws are not completed in the allotted
set time for a set screw fastening。
Lasting buzz s and LED red
flash
※In the set-up , if Lt and LL show “02.”means 0.02, push P to adjust decimal to become 0.2.
※During operation, LED will show three kinds of colors: OK is green light; NG is red light; standby learning is orange light.
※SKD-BE PCB has three kinds of signal, OUTPUT OK1, OKALL and N.G and is an open collector type.
※Output users need input voltage to drive the buzzer, the input voltage can’t be over DC24V 10mA.
※There is a new judgment which is the screwdriver will judge a N.G.in the case of there is a start signal and it is OFF
before Lt.
Push both UP + DOWN set up the buzzer：
ON Fastening a screw, completing work and mistaken operation, buzzer will be on.
OFF Wrong operation will be buzzed.
FF Work completed and wrong operation will cause buzz.
EF As one screw is fastened and work is completed, buzzer will be on; as mistake made has no buzz.
Counting Set-Up instruction
(4) OK All (3) N.G
(1) GND (1) GND
(2) OK ONE
(1) GND
NO. Function Color
1GND Black
2 OK ONE Brown
3N.G Red
4 OK All Orange
Open Collector接點


11
Ht/Lt Description:
※To shut down the count: If count needs be shut down, push P key for five seconds until no figures on the panel, meanwhile
LED 1 will show green light.
※If set value need be reset during counting, just push three seconds.
※Simulate-learning: as electric screwdriver is not used, push S key and then push P key to enter simulate-learning procedure;
SL(S)===SC(S)===At(S)=== Test Data===(P)
1) Show SL (Screw List), select UP/DOWN to change number and then push S(confirm)
2) Show SC (counting number), select UP/DOWN to change number and then push S(confirm)
3) Show At (automatic zero), UP/DOWN to change value; then push P (confirm)
4) Enter simulate-learning (LED 1 will keep flash)
5) When recording value, push P key and back working condition.
※LED light flash in simulate-learning.( means under simulate- learning condition), push P key to record value after simulate -learning. )
※As no use of screwdrivers: UP and push P key can set up waiting time.
If three seconds are set, but no starting signal after set time, it will buzz.
※Push R key to restore to factory settings.
General execution of pre-set program:
Start
Ht/Lt mainly set up the period of time. If stop is within the set period, it means OK. In contrast, it
will be (NG), as stop before Lt or after Ht. and should reconfirm whether wrong screws is taken. More
accuracy requested means more correct Ht/Lt set-up should be. The LT accepts 0.00, but it can be
increased or decreased in SELECT.
STAR
STOP
Lt
0.02 s
Ht
2.0 s
If screwdriver stops before Lt. If screwdriver has no stop after Ht.
N.G N.G
OK
It is “OK” as
screwdriver stops
between Lt and Ht.
Lt=0.02
Ht=2.0
LL=1.0
O
K
N.G N.G
Screws stuck or wrong screws Screws stripped or wrong screws
＊ If stop is among dots, it is normal fastening. “OK”will be shown.
＊ If stop is before Lt or over Ht, it is “N.G.”.
＊ User can freely adjust Lt. However, if Ht and Lt is closer, it will
re
q
uest more accurac
y
.


12
To adjust the torque on these screwdrivers. Proceed as follows :
1. Determine the torque output of the tool by checking a tightened Fastener with a torque wrench.
2. Increase or decrease the torque by rotating the Spring Adjusting Ring. Rotating the Ring clockwise to a
higher number on the torque Scale increase torque output while rotating the Ring counterclockwise to a
lower number decreases the torque output.
3. Check the adjustment with a torque wrench. A number of factors will affect torque output from one job to
another. Final torque adjustment should be made at the job through a series of gradual increase. Always
start below the desired torque and work upward.
4. Adjust the bit torque by changing the driving in length of the adjust ring at the end.
5. The relationship between torque scale and bit torque is as shown Ring, in the torque diagram. The figures
of torque scale do not indicate bit torque values. However, the clamping torque of screw itself is different
form type, size, material of the screw and the material of its mating part. Use it as standard to obtain an
appropriate clamping torque.
6. The (Return torque method) in which once-clamped screw is returned with torque wrench or the like is
available as one of torque control methods however, note that the measured values by the return torque
method generally appear in 10%~30% lower than the actually clamping torque.
7. The torque checker measures the torque of screwdriver. The clamping torque of screw itself is different
from the clamped conditions. Understand the correlation between clamping torque values and the torque
checker values perform the torque control properly.
Torque Adjustment Operation


13
1. Also in reverse rotation, the clutch is turned off in such manner as in normal rotation, stopping the motor
running. Accordingly, when the screw tightened at a large torque, set it to a higher torque scale.
2. The number from zero to eight on the Torque Scale is reference number only and not an indication of
actual torque output.
3. The power supplier will generate low power when the button of the power controller is switched to "LO."
Also, the electric screwdriver's torque output setting value should be adjusted to middle torsion value
accordingly.
4. The mechanical wear condition of the electric screwdriver depends on the torque, duration, and the
frequency that user used. In the case of using greater torque, the higher frequency and the longer
operation, the screwdriver will get worn faster. The new screwdriver uses in the scale of 4 for one month
(frequency: 12 pcs/ min; 8 hours / per day) will result in 3% ~ 5% torque decay. (Scale of 8 will result in
5% ~ 7% torque decay). By the growth in use of time, the torque decay level will gradually reduce and
stabilize. User could test the torque output of the screwdriver by torque meter periodically and then
adjust it to meet user’s requirement for the compensation of the torque decay.
5. Please refer to Kilews website http://www.kilews.com for the detail component list.
CAUTION

PRODUCTION NO.
THIRD ANGLE PROJECTION.
ITEM NO:
DES. BY
CHKD.BY
APPD.BY
TITLE:
CUSTOMERDWG NAME
DWG NO:
MATERIAL
DATE
DATE
DATE
UNIT
SHRINK
SCALESHT NO.
OF SHTS.
SKD-BE512LF
SKD-BE517LF
MODEL:

NO PARTS NO PARTS NAME-E PARTS NAME-C Q'ty NO PARTS NO PARTS NAME-E PARTS NAME-C Q'ty
1 AA50001-26 CORD ASSEMBLY 2M 電源線 2M 1 33 GC30341-3 CAM 上離合器頭 1
2 AA50001-52N CORD ASSEMBLY 檔尾電源線 1 34 GP30351 STEEL BALLS 跳脫鋼珠 2
3 CJ20011 SUSPENSION RING 起子吊環 1 35 GU30370 STOP PILOT 停止用酒杯 1
4 CC50017 TRIGGER ASSEMBLY 手按開關半成品 1 36 GP30371 STELL BALLS FOR A,C,D 酒杯鋼珠 (A,C,D) 2
CC50017-1 TRIGGER ASSEMBLY (ESD) 手按開關半成品(ESD) 1 GP30351 STELL BALLS FOR B 酒杯鋼珠 (B頭) 2
5 C40744F HOUSING-UNDERSIDE
(
A'ss
y)
(
BLUE-BLAC
K
下蓋半成品(白-黑) 1 37 GD30381A SHAFT FOR "A" TYPE 傳動軸(A頭) 1
C40744-1F HOUSING-UNDERSIDE-ESD (A'ssy) 下蓋半成品-防靜電 1 GD30381B-2 SHAFT FOR "B" TYPE 傳動軸(B頭) 1
6 CA50232 HOUSING-UPSIDE (WHITE-BLACK) 外殼上蓋(白-黑) 1 GD30381C SHAFT FOR "C" TYPE 傳動軸(C頭) 1
CA50232-1 HOUSING-UPSIDE (ESD) 外殼上蓋(ESD) 1 GD30381D SHAFT FOR "D" TYPE 傳動軸(D頭) 1
7 CE50152-3 PUSH ROD 開關推桿半成品 1 GD30383AD SHAFT FOR "AD" TYPE 傳動軸(AD頭) 1
8 CE80001 FIXTURE 三合一固定片 1 38 GP20331 STEEL BALLS FOR "A、D" TYPE(2ψ) 起子頭帽鋼珠(A、D用) 2
9 EG31418-15F PCB 計數機板成品 1 GP21291B STEEL BALLS FOR "B、C" TYPE(2.5mm) 起子頭帽鋼珠(B、C用) 2
10 W50110 PC BOARD GAP COLUMN PC板間隔柱 2 39 GF30401 WARING PLATE FOR "A,C,D" TYPE 扭力推盤(A,C,D用) 1
11 EG31418-16 PCB 驅動機板成品 1 GF30401B WARING PLATE FOR "B" TYPE 扭力推盤(B用) 1
12 CH90122-2 SCREW FOR PCB 螺絲 2 40 GO30541-3 SPRING FOR "BE512LF" 兩段式小彈簧(BE512LF) 1
13 CH30200 SCREW FOR FIXTURE 螺絲 2 GO30544 SPRING FOR "BE517LF" 兩段式小彈簧(BE517LF) 1
14 EG31421-1 PCB-CHANGEOVER 機板成品 (正反) 1 41 GO30531 SPRING CAP 彈簧蓋 1
15 CI50212-1 F/R SWITCHING ELEMENT 正反轉推板半成品 1 42 GE50411-4 WARING SPRING FOR "BE512LFA.C.D" 扭力彈簧(BE512LFA.C.D) 1
16 C50213-1 BOTTOM 矽膠按鍵 1 GE50411-5 WARING SPRING FOR "BE512LFB" 扭力彈簧(BE512LFB) 1
17 CH20102 SCREW FOR HOUSING 螺絲 4 GE30413-9 WARING SPRING FOR "BE517LFA.C.D" 扭力彈簧(BE517LFA.C.D) 1
18 MI90302 PILOT ROD 開關引導棒 1 GE30413-12 WARING SPRING FOR "BE517LFB" 扭力彈簧(BE517LFB) 1
19 CH20102-24 SCREW FOR MOTOR 馬達螺絲 4 43 GY30421 WARING SPRING BASE FOR "A,C,D" TYPE 止推盤(A,C,D) 1
20 MO50115CE MOTOR ASSEMBLY FOR 馬達整組 1 GY30421B WARING SPRING BASE FOR "B" TYPE 止推盤(B) 1
21 M20102-1 GEAR COUPLER 主齒連接套 1 44 GK20231B "C"-RING FOR GY30421B (LB) 傳動軸固定C環 1
22 M11324 GEAR 馬達主齒 1 45 GB30441-12A CLUTCH CASE (A,C,D) 下離合器筒 (A,C,D)1
23 MG30081-1 PILOT ROD 陶瓷棒 1 GB30441-1A CLUTCH CASE (B) 下離合器筒 (B) 1
24 GZ51901-3A CLUTCH ASSEMBLY FOR "BE512LFA" 離合器整組 (BE512LFA) 1 46 GO30452 BIT SPRING FOR "A,C,D" TYPE 起子頭帽彈簧(A,C,D) 1
GZ51901-5BF CLUTCH ASSEMBLY FOR "BE512LFB" 離合器整組 (BE512LFB) 1 GO20391B BIT SPRING FOR "B" TYPE 起子頭帽彈簧(B) 1
GZ51901-3C CLUTCH ASSEMBLY FOR "BE512LFC" 離合器整組 (BE512LFC) 1 47 GJ30461 BIT SLEEVE FOR "A,C,D" TYPE 起子頭帽(A,C,D) 1
GZ51901-3D CLUTCH ASSEMBLY FOR "BE512LFD" 離合器整組 (BE512LFD) 1 GJ3046B BIT SLEEVE FOR "B" TYPE 起子頭帽(B) 1
GZ51901-3AD CLUTCH ASSEMBLY FOR "BE512LFAD" 離合器整組 (BE512LFAD) 1 48 GQ30471 "C" RING FOR "A,C,D" 起子頭帽C環(A,C,D) 1
GZ51903-3A CLUTCH ASSEMBLY FOR "BE517LFA" 離合器成品 (BE517LFA) 1 GQ21361 "C" RING FOR "B" 起子頭帽C環(B) 1
GZ51903-5BF CLUTCH ASSEMBLY FOR "BE517LFB" 離合器成品 (BE517LFB) 1 49 GL30481-1 TORQUE ADJUST PIN 扭力調整棒 4
GZ51903-3C CLUTCH ASSEMBLY FOR "BE517LFC" 離合器成品 (BE517LFC) 1 50 GM30491 TORQUE ADJUST RING 扭力調整環 1
GZ51903-3D CLUTCH ASSEMBLY FOR "BE517LFD" 離合器成品 (BE517LFD) 1 51 GS30501 "C" RING FOR GM30491 扭力環C環 1
GZ51903-3AD CLUTCH ASSEMBLY FOR "BE517LFAD" 離合器成品 (BE517LFAD) 1 52 CD20111-1 COUPLER 外殼前鎖環 1
25 MI31221 PILOT ROD FOR"A,C,D"TYPE 開關引導棒 (A;C;D) 1 CD20111-2 COUPLER ESD 外殼前鎖環 ESD 1
MI33241 PILOT ROD FOR"B"TYPE 開關引導棒 (B) 1 53 CH50671-7 GROUNDING MEANS 接地線 1
26 GK20231 "C" RING 齒輪固定C環 1 54 CH20102-8 WASHER 華司 1
27 GI20251-1 IRON WASHER 齒輪固定片 1 55 CH20514 SCREW 地線螺絲 1
28 G21302 SPACER 快速墊圈 1 56 CK28031-1 TRIGGER SPRING 壓板彈簧 1
29 GH20241-1 IDLE GEAR 游星齒輪 3 57 GN30435 MAIN BEARING 離合器主軸承 1
30 GG20271-1 GEAR SEAT 齒盤 1 58 C50226 Fixture 開關保護蓋 1
31 GA91284-1 GEAR CASE 上離合器筒 1 59 CH90122 SCREW 螺絲 2
32 GN30321 MAIN BEARING 離合器主軸承 1
BE512LF BE517LF(CE)